Skip to main content

MODELADO CINEMATICO Y DINAMICO DEL MOVIMIENTO DE LOS TEJIDOS BLANDOS. APLICACION AL DISEÑO DE MODELOS BIOMECANICOS (DESARROLLO DE TECNICAS EXPERIMENTALES Y VALIDACION DE MODELOS)

DPI2009-13830-C02-02

•
Funding agency name Ministerio de Ciencia e Innovación
Funding agency acronym MICINN
Program Programa Nacional de Proyectos de Investigación Fundamental
Subprogram Subprograma de Proyectos de Investigación Fundamental no Orientada
Call Proyectos I+D
Call year 2009
State Plan 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Management unit Subdirección General de Proyectos de Investigación
Beneficiary centre INSTITUTO DE BIOMECANICA DE VALENCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 7
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Model of Soft Tissue Artifact Propagation to Joint Angles in Human Movement Analysis

  • Page Del Pozo, Alvaro Felipe|||0000-0002-5432-310X
  • Mata Amela, Vicente|||0000-0003-2255-0567
  • Besa Gonzálvez, Antonio José|||0000-0002-7084-9937
  • De Rosario Martínez, Helios
[EN] This work describes the kinematic laws that govern the transmission of soft tissue artifact errors to kinematic variables in the analysis of human movements. Artifacts are described as relative translations and rotations of the marker cluster over the bone, and a set of explicit expressions is defined to account for the effect of that relative motion on different representations of rotations: the rotation around the screw axis, or rotation vector, and three Euler angle sequences (XY0Z, YX0Y00, ZX0 Y00). Although the error transmission is nonlinear in all cases, the effect of artifacts is greater on Euler sequences than on the rotation vector. Specifically, there are crosstalk effects in Euler sequences that amplify the errors near singular configurations. This fact is an additional source of variability in studies that describe artifacts by comparing the Euler angles obtained from skin markers, with the angles of an artifact-free gold standard. The transmission of errors to rotation vector coordinates is less variable or dependent on the type of motion. This model has been tested in an experiment with a deformable mechanical model with a spherical joint., This work has been funded by the Spanish Government and co-financed by EU FEDER funds (Grants DPI2009-13830-C02-01 and DPI2009-13830-C02-02).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Kinematic description of soft tissue artifacts: quantifying rigid versus deformation components and their relation with bone motion

  • De Rosario Martínez, Helios
  • Conejero Navarro, Efrain
  • Page Del Pozo, Alvaro Felipe|||0000-0002-5432-310X
  • Besa Gonzálvez, Antonio José|||0000-0002-7084-9937
  • Mata Amela, Vicente|||0000-0003-2255-0567
[EN] This paper proposes a kinematic approach for describing soft tissue artifacts (STA) in human movement analysis. Artifacts are represented as the field of relative displacements of markers with respect to the bone. This field has two components: deformation component (symmetric field) and rigid motion (skew-symmetric field). Only the skew-symmetric component propagates as an error to the joint variables, whereas the deformation component is filtered in the kinematic analysis process. Finally, a simple technique is proposed for analyzing the sources of variability to determine which part of the artifact may be modeled as an effect of the motion, and which part is due to other sources. This method has been applied to the analysis of the shank movement induced by vertical vibration in 10 subjects. The results show that the cluster deformation is very small with respect to the rigid component. Moreover, both components show a strong relationship with the movement of the tibia. These results suggest that artifacts can be modeled effectively as a systematic relative rigid movement of the marker cluster with respect to the underlying bone. This may be useful for assessing the potential effectiveness of the usual strategies for compensating for STA. © 2012 International Federation for Medical and Biological Engineering., This work has been funded by the Spanish Government and co-financed by EU FEDER funds (Grants DPI2009-13830-C02-01, DPI2009-13830-C02-02 and IMPIVA IMDEEA/2012/79 and IMDEEA/2012/80).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Propagation of Artifact Errors on Kinematic Variables. Effect on Euler Angles

  • De Rosario Martínez, Helios
  • Moreno Cano, Rafael
  • Page Del Pozo, Alvaro Felipe|||0000-0002-5432-310X
  • Mata Amela, Vicente|||0000-0003-2255-0567
  • Besa Gonzálvez, Antonio José|||0000-0002-7084-9937
This work has been funded by the Spanish Government and co-financed by EU FEDER funds (Grants DPI2009-13830-C02-01, DPI2009-13830- C02-02 and IMPIVA IMIDIC/2010/84)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Representation of planar motion of complex joints by means of rolling pairs. Application to neck motion

  • Page Del Pozo, Alvaro Felipe|||0000-0002-5432-310X
  • Mata Amela, Vicente|||0000-0003-2255-0567
  • De Rosario Martínez, Helios
  • Galvez Griso, Jose Antonio
[EN] We propose to model planar movements between two human segments by means of rolling-without-slipping kinematic pairs. We compute the path traced by the instantaneous center of rotation (ICR) as seen from the proximal and distal segments, thus obtaining the fixed and moving centrodes, respectively. The joint motion is then represented by the rolling-without-slipping of one centrode on the other. The resulting joint kinematic model is based on the real movement and accounts for nonfixed axes of rotation; therefore it could improve current models based on revolute pairs in those cases where joint movement implies displacement of the ICR. Previous authors have used the ICR to characterize human joint motion, but they only considered the fixed centrode. Such an approach is not adequate for reproducing motion because the fixed centrode by itself does not convey information about body position. The combination of the fixed and moving centrodes gathers the kinematic information needed to reproduce the position and velocities of moving bodies. To illustrate our method, we applied it to the flexion-extension movement of the head relative to the thorax. The model provides a good estimation of motion both for position variables (mean R pos=0.995) and for velocities (mean R vel=0.958). This approach is more realistic than other models of neck motion based on revolute pairs, such as the dual-pivot model. The geometry of the centrodes can provide some information about the nature of the movement. For instance, the ascending and descending curves of the fixed centrode suggest a sequential movement of the cervical vertebrae. © 2010 Elsevier Ltd., This work was funded by the Spanish Government and co-financed by EU FEDER funds (Grants DPI2006-14722-C02-01, DPI2006-14722-C02-02, DPI2009-13830-C02-01, DPI2009-13830-C02-02 and Ramon y Cajal contract to JAG).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis doctoral (DoctoralThesis)

Cinemática de la flexión del tronco en postura sedente. Aproximación basada en el eje instantáneo de rotación

  • De Rosario Martínez, Helios
[EN] This PhD Thesis presents a research on trunk kinematics in seated posture, applied to defining a biomechanical model of the flexion-extension movement, and exploring the relationship between the trunk movement and the mechanisms of reclining work chairs. This research starts from a new way of characterizing human body movements. The proposed method uses a unified vector notation to analyze velocities as well as finite displacements. The main parameter was the instantaneous axis of rotation, which describes the geometric characteristics of movement, and may be used to interpret how body segments are joined. The analysis is based on explicit formulas, which allow a mathematical estimation of instrumental errors and controlling their size, which is critical in the calculation of the instantaneous axis. The trunk was modeled as a kinematic chain consisting of two rigid bodies (pelvis and thorax) that move relative to the seat. No restrictions were imposed on the movement beforehand, so that this free model let the movement describe itself. We conducted a series of experiments to validate the theory that supported the methodology, to quantify the errors that affected the measures, and to study the trunk movement in relation to a variety of office chairs. These experiments yielded a biomechanical model of trunk flexion in seated posture, that showed a rotation axis of the pelvis higher than former models, and a sequential rotation of lumbar vertebrae. We also studied experimentally the kinematics of reclining chairs mechanisms, and how they altered the movement of the thorax when subjects sat on them. The results of this research provide a new insight on human movement in general, and about seated posture in particular, and they also contribute to developing new ideas about the design of chairs and their relation to trunk mobility, [ES] En esta tesis doctoral se presenta el desarrollo de una investigación sobre la cinemática del tronco en la postura sedente, aplicada a la definición de un modelo biomecánico del movimiento de flexo-extensión, y al estudio de la relación entre el movimiento del tronco y los mecanismos de reclinación de las sillas de trabajo. Esta investigación parte de una nueva forma de caracterizar los movimientos del cuerpo humano. Se ha utilizado una notación vectorial unificada para estudiar las velocidades y los desplazamientos finitos. El principal elemento de estudio ha sido el eje instantáneo de rotación, que describe las características geométricas del movimiento y sirve para interpretar cómo se encuentran articulados los segmentos corporales. El procedimiento de análisis se basa en fórmulas explícitas, que permiten una estimación matemática de los errores instrumentales y controlar su magnitud, aspecto crítico a la hora de calcular los ejes instantáneos de rotación. El tronco se ha modelado como una cadena cinemática formada por dos cuerpos rígidos (pelvis y tórax) que se mueven respecto al asiento. No se ha impuesto ningún tipo de restricción previa al modelo, dejándole libertad para que el movimiento se describiese a sí mismo. Se ha llevado a cabo una serie de experimentos para validar la teoría que da base a la metodología, cuantificar los errores que afectaban a las medidas, y estudiar el movimiento del tronco en relación con una serie de sillas de oficina. Se ha definido un modelo biomecánico de la flexión del tronco en la postura sedente sin respaldo, que presenta un eje de rotación de la pelvis más elevado que el de modelos previos y una rotación secuencial de las vértebras lumbares. Además se ha estudiado experimentalmente la cinemática de los mecanismos de sillas reclinables y cómo se altera el movimiento del tórax al sentarse en ellas. Los resultados obtenidos aportan una nueva visión sobre el movimiento humano en general y el de la postura sedente en particular, y también contribuyen al desarrollo de nuevas ideas sobre el diseño de sillas y su relación con la movilidad del tronco., [CA] En aquesta tesi doctoral es presenta el desenvolupament d’una investigació sobre la cinemàtica del tronc en la postura sedent, aplicada a la definició d’un model biomecànic del moviment de flexo-extensió, i a l’estudi de la relació entre el moviment del tronc i els mecanismes de reclinació de les cadires de treball. Aquesta investigació parteix d’una nova forma de caracteritzar els moviments del cos humà. S’ha utilitzat una notació vectorial unificada per a estudiar les velocitats i els desplaçaments finits. El principal element d’estudi ha estat l’eix instantani de rotació, que descriu les característiques geomètriques del moviment i serveix per a interpretar com es troben articulats els segments corporals. El procediment d’anàlisi es basa en fórmules explícites, que permeteixen una estimació matemàtica dels errors instrumentals i controlar la seva magnitud, aspecte crític a l’hora de calcular els eixos instantanis de rotació. El tronc s’ha modelat com una cadena cinemàtica formada per dos cossos rígids (pelvis i tòrax) que es mouen respecte al seient. No s’ha imposat cap tipus de restricció prèvia al model, deixant llibertat per a que el moviment es descriga a si mateix. S’ha dut a terme una sèrie d’experiments per a validar la teoria que dóna base a la metodologia, quantificar els errors que afectaven a les mesures, i estudiar el moviment del tronc en relació amb una sèrie de cadires d’oficina. S’ha definit un model biomecànic de la flexió del tronc en la postura sedent sense respatller, que presenta un eix de rotació de la pelvis més elevat que el considerat per models previs i una rotació seqüencial de les vèrtebres lumbars. A més s’ha estudiat experimentalment la cinemàtica dels mecanismes de cadires reclinables i com s’altera el moviment del tòrax al seure-hi. Els resultats obtinguts aporten una nueva visió sobre el moviment humà en general i el de la postura sedent en particular, i també contribueixen al desenvolupament de noves idees sobre el disseny de cadires i la seva relació amb la mobilitat del tronc., A los Planes Nacionales de I+D coordinados entre la UPV y el IBV, Nuevos Modelos Biomecánicos Basados en Sistemas No Paramétricos (DPI2003-07883-C02-02), Generación de Criterios para el Desarrollo de Modelos Biomecánicos Articulares a partir de Datos Antropométricos Funcionales (DPI2006-14722-C02-02) y Modelado cinemático y dinámico del movimiento de los tejidos blandos (DPI2009-13830-C02-02). Son éstos los proyectos que han dado la oportunidad de llevar a cabo la investigación, y han facilitado el intercambio de conocimientos en análisis de mecanismos y en biomecánica, necesario para el éxito del trabajo.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Propagation of soft tissue artifacts to the center of rotation: A model for the correction of functional calibration techniques

  • De Rosario Martínez, Helios
  • Page Del Pozo, Alvaro Felipe|||0000-0002-5432-310X
  • Besa Gonzálvez, Antonio José|||0000-0002-7084-9937
  • Valera Fernández, Ángel|||0000-0001-6843-6394
This paper presents a mathematical model for the propagation of errors in body segment kinematics to the location of the center of rotation. Three functional calibration techniques, usually employed for the gleno-humeral joint, are studied: the methods based on the pivot of the instantaneous helical axis (PIHA) or the finite helical axis (PFHA), and the ¿symmetrical center of rotation estimation¿ (SCoRE). A procedure for correcting the effect of soft tissue artifacts is also proposed, based on the equations of those techniques and a model of the artifact, like the one that can be obtained by double calibration. An experiment with a mechanical analog was performed to validate the procedure and compare the performance of each technique. The raw error (between 57 and 68 mm) was reduced by a proportion of between 1:6 and less than 1:15, depending on the artifact model and the mathematical method. The best corrections were obtained by the SCoRE method. Some recommendations about the experimental setup for functional calibration techniques and the choice of a mathematical method are derived from theoretical considerations about the formulas and the results of the experiment., This work has been funded by the Spanish Government (Grants DPI2009-13830-C02-01, DPI2009-13830-C02-02, DPI2010-20814-C02-01, and DPI2010-20814-C02-02).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Point of optimal kinematic error: Improvement of the instantaneous helical pivot method for locating centers of rotation

  • De Rosario Martínez, Helios
  • Page Del Pozo, Alvaro Felipe|||0000-0002-5432-310X
  • Mata Amela, Vicente|||0000-0003-2255-0567
[EN] This paper proposes a variation of the instantaneous helical pivot technique for locating centers of rotation. The point of optimal kinematic error (POKE), which minimizes the velocity at the center of rotation, may be obtained by just adding a weighting factor equal to the square of angular velocity in Woltring's equation of the pivot of instantaneous helical axes (PIHA). Calculations are simplified with respect to the original method, since it is not necessary to make explicit calculations of the helical axis, and the effect of accidental errors is reduced. The improved performance of this method was validated by simulations based on a functional calibration task for the gleno-humeral joint center. Noisy data caused a systematic dislocation of the calculated center of rotation towards the center of the arm marker cluster. This error in PIHA could even exceed the effect of soft tissue artifacts associated to small and medium deformations, but it was successfully reduced by the POKE estimation., This work has been funded by the Spanish Government (Grants DPI2009-13830-C02-01, DPI2009-13830-CO2-02, DPI2010-20814-CO2-01, DPI2010-20814-CO2-02).