Skip to main content

ELABORACION DE MODELOS TERMOFLUIDODINAMICOS Y TECNICAS EXPERIMENTALES PARA DESARROLLAR UN COLECTOR DE ESCAPE MULTIFUNCIONAL CON UN FILTRO DE PARTICULAS DIESEL INTEGRADO

DPI2010-20891-C02-02

•
Funding agency name Ministerio de Ciencia e Innovación
Funding agency acronym MICINN
Program Programa Nacional de Proyectos de Investigación Fundamental
Subprogram Subprograma de Proyectos de Investigación Fundamental no Orientada
Call Proyectos I+D
Call year 2010
State Plan 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Management unit Subdirección General de Proyectos de Investigación
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 11
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental theoretical methodology for determination of inertial pressure drop distribution and pore structure properties in wall-flow diesel particulate filters (DPFs)

  • Payri, F.|||0000-0002-3314-4911
  • Broatch, A.|||0000-0001-9991-1039
  • Serrano, J.R.|||0000-0003-0692-3917
  • Piqueras, P.|||0000-0002-3767-0839
Wall-flow particulate filters have been placed as a standard technology for Diesel engines because of the increasing restrictions to soot emissions. The inclusion of this system within the exhaust line requires the development of computational tools to properly simulate its flow dynamics and acoustics behaviour. These aspects become the key to understand the influence on engine performance and driveability as a function of the filter placement. Since the pressure drop and the filtration process are strongly depending on the pore structure properties - permeability, porosity and pore size - a reliable definition of these characteristics is essential for model development. In this work a methodology is proposed to determine such properties based on the combination of the pressure drop rement in a steady flow test rig and two theoretical approaches. The later are a lumped model and a one-dimensional (1D) unsteady compressible flow model. The purpose is to simplify the integration of particulate filters into the global engine modelling and development processes avoiding the need to resort to specific and expensive characterisation tests. The proposed methodology was validated against measurements of the response of an uncoated diesel particulate filter (DPF) under different flow conditions as cold steady flow, impulsive flow and hot pulsating flow. © 2011 Elsevier Ltd., This work has been partially supported by the Spanish Ministerio de Ciencia e Innovacion through grant number DPI2010-20891-C02-02.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Heat transfer modelling in honeycomb wall-flow diesel particulate filters

  • Galindo, José|||0000-0001-6068-182X
  • Serrano, J.R.|||0000-0003-0692-3917
  • Piqueras, P.|||0000-0002-3767-0839
  • García Afonso, Óscar
Heat transfer in wall-flow monoliths has gained in interest because of the widespread adoption of these systems by automotive industry to fulfil soot emission regulations and the importance of heat exchange on the regeneration process control to avoid damaging the monolith. This paper presents a heat transfer model for wall-flow diesel particulate filters coupled with an unsteady compressible flow solver. The heat exchange between the gas and the solid phase is based on a bi-dimensional discretisation of the porous medium both in axial and tangential directions. The monolith can be discretised in the radial direction to account for the heat fluxes towards the environment through the monolith and the canister, which is also coupled with the inlet and outlet ducts of the filter. The model is validated against experimental data obtained in a flow test rig. A test campaign under non-reacting conditions has been conducted to show the capability for thermal response prediction. Tests cover clean and soot loaded monolith, continuous flow under steady and transient thermal conditions, and pulsating flow. In this case, the characteristics of the pressure waves in amplitude and frequency are similar to those that the monolith can undergo depending on its location along the exhaust line. © 2012 Elsevier Ltd., This work has been partially supported by the Spanish Ministerio de Ciencia e Innovacion through grant number DPI2010-20891-C02-02.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of shock capturing methods for chemical species transport in unsteady compressible flow

  • Serrano, J.R.|||0000-0003-0692-3917
  • Climent, H.|||0000-0002-2407-5651
  • Piqueras, P.|||0000-0002-3767-0839
  • García Afonso, Óscar
This paper presents a chemical species transport model to account for variable composition and gas properties along the flow path in internal combustion engines. The numerical solution to adapt the gas dynamic model to chemical species transport in boundary conditions by means of the Method of Characteristics and in volumes by means of a filling and emptying model is described. The performance for chemical species transport in 1D elementsof shock-capturing methods, such as the two-step Lax Wendroff method and the Sweby s TVD scheme considering several flux limiter definitions, is carried out by means of shocktube tests. The influence of the fluid modelling as perfect or non-perfect gas on the numerical methods features and the flow characteristics on shock-tube results are analysed., This work has been partially supported by the Spanish Ministerio de Ciencia e Innovacion through grant number DPI2010-20891-C02-02.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Application of the two-step Lax and Wendroff FCT and the CE-SE method to flow transport in wall-flow monoliths

  • Serrano, J. R.
  • García Afonso, Óscar
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Piqueras, P.|||0000-0002-3767-0839
[EN] Gas dynamic codes are computational tools applied to the analysis of air management in internal combustion engines. The governing equations in one-dimensional elements are approached assuming compressible unsteady non-homentropic flow and are commonly solved applying finite difference numerical methods. These techniques can also be applied to the calculation of flow transport in complex systems such as wallflow monoliths. These elements are characterized by alternatively plugged channels with porous walls. It filters the particulates when the flowgoes through thewall from the inlet to the outlet channels. Therefore, this process couples the solution of every pair of inlet and outlet channels. In this study, the adaptation of the two-step Lax and Wendroff method and the space-time Conservation Element and Solution Element method is performed to be applied in the solution of flow transport in wall-flow monolith channels. The influence on the prediction ability is analysed by a shock-tube test and experimental data obtained under impulsive flow conditions., This work has been partially supported by the Spanish Ministerio de Ciencia e Innovacion through grant number DPI2010-20891-C02-02.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Theoretical and experimental study of mechanical losses in automotive turbochargers

  • Serrano, J.R.|||0000-0003-0692-3917
  • Olmeda, P.|||0000-0002-3161-0165
  • Tiseira, Andrés-Omar|||0000-0001-9472-2386
  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
  • Lefebvre, Alain
The aim of the present work is to show an approximation, through an experimental an theoretical study, to quantify the mechanical losses in a turbocharging system. These are linked to the dynamics in the turbo shaft bearings, both axial and radial. Theoretical and experimental methodologies are presented in order to develop a mechanical losses model. The experimental work consists on a measurement campaign in quasi-adiabatic operating conditions, while in the theoretical part, a mathematical model is developed taking into account the radial and axial bearings. The model uses some assumptions in order to solve the Navier-Stokes equations, leading to a simplified model which includes viscosity and the Reynolds number of the oil film formed on the bearings. The proposed model has shown a good agreement with the experimental data, The authors of this paper wish to thank M.A. Ortiz and V. Ucedo for their invaluable work during the experimental setup and campaign, F.J. Arnau, Ph.D, for its excellent job maintaining and expanding Open WAMs code base and M.A. Reyes-Belmonte for all his hard and rigorous work extrapolating turbine maps and preparing and launching the simulations. This work has been partially supported by the Spanish Ministerio de Ciencia e Innovacion through grant number DPI2010-20891-C02-02.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Uncertainties in power computations in a turbocharger test bench

  • Olmeda, P.|||0000-0002-3161-0165
  • Tiseira, Andrés-Omar|||0000-0001-9472-2386
  • Dolz, Vicente|||0000-0003-1511-6957
  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
A specific study of the uncertainties of turbine power output measured in turbocharger test benches is presented using the law of uncertainty propagation and the influence of the different terms that contribute to it is shown. Then, non-linear mixed integer mathematical programming algorithms used with the turbine power uncertainty expression become an essential tool to overcome the problem of selection new sensors to improve an existing test rig or to contribute to a new one. A method of optimisation is presented for two different scenarios: first, where the maximum cost is a constraint; second where the maximum uncertainty is a constraint and the total cost is minimised. When using a large transducers database, computational efforts may be reduced by solving the relaxed non-integer problem by means of sequential quadratic programming and then probing the ceilings and floors of the parameters to get an optimum approximation with low costs. A comparison between the linear uncertainty propagation model and Monte Carlo simulations is also presented, only showing benefits of the later method when computing high order statistical moments of the turbine power output probability distribution., This work has been partially supported by the Spanish Ministerio de Ciencia e Innovacion through Grant No. DPI2010-20891-C02-02 and by the Spanish Ministerio de Economia y Competitividad through Grant No. TRA2012-36954.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Study of the turbocharger shaft motion by means of infrared sensors

  • Serrano, J.R.|||0000-0003-0692-3917
  • Guardiola, Carlos|||0000-0002-3150-8566
  • Dolz-García, Vicente Manuel
  • López, M.A.
  • Bouffaud, F.
This work describes a technique for measuring the precession movement of the shaft of small automotive turbochargers. The main novelty is that the technique is based on infrared light diode sensors. With presented technique it is possible to perform secure mounting of electronics and also to measure, with good accuracy, far enough from the turbocharger shaft. Both advantages allow applying it even in critical lubrication conditions and when blade contact occurs. The technique's main difficulties arise from the small size of the turbocharger shaft and the high precession movement in critical conditions. In order to generate the optimum albedo reflection for infrared measurement, a special cylindrical nut with larger diameter than the original one is assembled at the shaft tip in the compressor side. Following, shaft balancing, the calibration of the sensors and the compensation of errors from different sources are needed steps before the method is able to identify the main frequencies of shaft motion. Once synchronous and sub-synchronous frequencies have been obtained it is possible to reconstruct the instantaneous position of the shaft to determine its precession movement., This research has also been partially supported by the Programa de Desarrollo del Talento Humano de la Secretaria Nacional de Educacion Superior, Ciencia, Tecnologia e Innovacion del Gobierno Ecuatoriano No. 20100289.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Pollutants emission and particle behavior in a pre-turbo aftertreatment light-duty diesel engine

  • Bermúdez, Vicente|||0000-0002-2781-5598
  • Luján, José M.|||0000-0001-6133-8943
  • Piqueras, P.|||0000-0002-3767-0839
  • Campos, Daniel
Diesel particulate filters are a standard technology used in diesel engines in order to comply with actual and forthcoming regulations, regarding soot emissions and particulate matter in exhaust gases. In recent years, pre-turbo aftertreatment response has been investigated as opposed to the traditional aftertreatment location downstream from the turbine but just regarding engine performance. Previous studies do not deal in detail with gaseous and particle emission analysis in a pre-turbo aftertreatment configuration. This paper focuses on these topics. The gaseous and particle emissions have been assessed in a 4-cylinder, light-duty diesel EURO 4 engine typically used in European passenger car vehicles. Different steady-state operating points have been considered in order to extend the study over a wide range of operating conditions. Additionally, the New European Driving Cycle has been performed with the aim of reaching a comprehensive understanding of the aftertreatment dynamic response in terms of pollutant emissions. An increase in the amount of NO2 converted from NO and a reduction in emitted CO have been found at low load steady-state operating conditions with pre-turbo aftertreatment placement In driving cycle conditions, a shift from nucleation to accumulation mode particles have been found, being the filtration efficiency scarcely affected. (C) 2014 Elsevier Ltd. All rights reserved., This work has been partially supported by the Spanish Ministerio de Ciencia e Innovacion through grant number DPI2010-20891-C02-02. The authors would like to thank Jose Ramon Serrano for his help.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A fluid dynamic model for unsteady compressible flow in wall-flow diesel particulate filters

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Serrano, J.R.|||0000-0003-0692-3917
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Piqueras, P.|||0000-0002-3767-0839
The use of particulate filters (DPF) in Diesel engines has become in recent years the standard technology for the control of soot aerosol emissions. Once emissions reduction through the management of filtration and regeneration aspects has reached its maturity, the effect of the system location on engine performance and acoustics are key topics to be addressed. In this paper, a fluid dynamic model for wall-flow monolith filters is described in which non-homentropic one-dimensional unsteady compressible flow is considered. The good agreement with experimental data confirms that the model is able to describe the mechanisms contributing to the pressure drop across the whole filter under steady and impulsive flow conditions. The approach of the flow governing equations provides a reliable evaluation of the contributions to the pressure drop with axial resolution in the description of the flow field properties. In addition, the frequency response predicted by the model confirms its ability to evaluate the dynamic response and acoustic potential of the DPF. © 2010 Elsevier Ltd., This work has been partially supported by the Spanish Ministerio de Ciencia e Innovacion through grant number DPI2010-20891-C02-02.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Assessment by means of gas dynamic modelling of a pre-turbo diesel particulate filter configuration in a turbocharged HSDI diesel engine under full-load transient operation

  • Bermúdez, Vicente|||0000-0002-2781-5598
  • Serrano, J.R.|||0000-0003-0692-3917
  • Piqueras, P.|||0000-0002-3767-0839
  • García Afonso, Óscar
Diesel particulate filters (DPF) are becoming a standard technology in diesel engines because of the need for compliance with forthcoming regulations regarding soot emissions. When a great degree of maturity in management of filtration and regeneration has been attained, the influence of the DPF placement on the engine performance emerges as a key issue to be properly addressed. The novelty of this work leads to the study of an unusual location of an aftertreatment device in the architecture of the turbocharged diesel engine exhaust line. The problem of the pre-turbo DPF placement is tackled comparing the engine response under full-load transient operation as opposed to the traditional DPF location downstream of the turbine. The study has been performed on the basis of a gas dynamic simulation of the engine, which has been validated with experimental data obtained under steady-state and transient conditions. The DPF response has been simulated with a model able to deal with the characteristic highly pulsating flow upstream of the turbine. Several levels of DPF soot loading have been considered to represent fully the most exigent conditions in terms of performance requirements. As a result, the main physical phenomena controlling the engine and DPF response and interaction have been identified. Placing the DPF upstream of the turbine will lead to a number of important advantages, owing to the continuous regeneration mode at which the DPF will operate, the lower pressure drop in the DPF, and the thermal energy storage in the DPF, which is very useful to mitigate 'turbocharger lag' during engine transient operation. These three effects have been evidenced with calculations performed using the validated model and the results have been fully analysed and discussed., This work has been partially supported by the Spanish MCI grant DPI2010-20891-C02-02.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Contribution to the Modeling and Understanding of Cold Pulsating Flow Influence in the Efficiency of Small Radial Turbines for Turbochargers

  • Serrano, J.R.|||0000-0003-0692-3917
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Fajardo, Pablo
  • Reyes Belmonte, Miguel Ángel
  • Vidal, Fabrice
In the present paper, an unsteady approach to determine the performance of a small radial inflow turbine working under cold pulsating flow is presented. It has been concluded that a reasonably good characterization of turbine behavior working with pulsating flow can be obtained using, in a quasi-steady way, models of the turbine isentropic efficiency and turbocharger mechanical efficiency. Both models have been fitted using data obtained from a steady flow characterization procedure. Turbocharger-measured parameters from the cold pulsating flow campaign have been compared with the ones obtained from one-dimensional gas dynamics computational modeling. The modeling approach is based on quasi-steady isentropic and mechanical efficiency models. Reasonably good accuracy in compressor and turbine variables prediction has been obtained for most of the operative conditions. Influence of amplitude and frequency of the pulsating flow over the instantaneous and average turbine efficiency has been studied to put some light on the analysis of the involved physical phenomena. The main conclusion is that the biggest effect of unsteady flow on turbine efficiency is through the influence on blade jet to speed ratio. It has been also concluded that, for the same average blade jet to speed ratio, pulses' amplitude does not influence turbine efficiency when it is closed, but does at other variable geometry turbine (VGT) positions. The effect of pulses' frequency is less evident and only influences VGT performance at the highest VGT openings., The authors wish to thank part of the economical support for this work to Spanish Grant DPI210-20891-C02-02 from Ministerio de Ciencia e Innovacion.