Skip to main content

PROPAGACION Y EMISION DE RUIDO DE ADMISION EN MOTORES TURBO-SOBREALIMENTADOS

DPI2015-70464-R

•
Funding agency name Ministerio de Economía y Competitividad
Funding agency acronym MINECO
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2015
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Management unit Dirección General de Investigación Científica y Técnica
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Measuring turbocharger compressor inlet backflow through particle image velocimetry

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Broatch, A.|||0000-0001-9991-1039
  • Pastor, José V.|||0000-0003-4113-4681
  • García-Tíscar, Jorge|||0000-0003-4934-4587
  • Sharma, Raj K.
  • Cheung, R.
[EN] An experimental measurement campaign is presented where particle image velocimetry (PIV) was used in an effort to characterize the velocity field in a turbocharger compressor when unstable operating conditions lead to flow reversing from the diffuser into the inlet pipe. Previous studies have successfully used this and similar techniques, but the most relevant results have been obtained in an open compressor where the backflow can diffuse into the ambient. In this work a glass pipe long enough to confine the full extent of the backflow has been used. Advantage was taken from the fact that this backflow is at higher temperature due to the compression process, enabling a preliminary work where a thermocouple array was used to estimate its maximum length across the compressor map. Using these results as a reference both axial and transversal velocity fields were measured. Issues associated with each one are described, along with relevant results that show how the technique correctly identifies the reversed flow, a conclusion that is supported by the comparison of the velocity average and standard deviation profiles with those of measured temperature., This work has been partially supported by Jaguar Land Rover Limited, Abbey Road, Whitley, Coventry CV3 4LF, UK. The equipment used in this work has been partially supported by the Spanish Ministerio de Economia y Competitividad through grant no DPI2015-70464-R and by FEDER - EU project funds "Dotaciem de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)" framed in the operational program of unique scientific and technical infrastructure of the Spanish Ministerio de Economia y Competitividad. J. Garcia-Tiscar was partially supported through contract FPI-S22015-1530 of the Programa de Apoyo para la Investigacion y Desarrollo (PAID) of Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

On the influence of inlet elbow radius on recirculating backflow, whoosh noise and efficiency in turbocharger compressors

  • Broatch, A.|||0000-0001-9991-1039
  • Ruiz-Rosales, Santiago|||0000-0001-9536-3696
  • García-Tíscar, Jorge|||0000-0003-4934-4587
  • Roig-Villanueva, Ferran
[EN] While the influence of inlet geometry on turbocharger compressor behaviour has usually been investigated in terms of performance, surge margin and efficiency, data is scarce regarding the impact of the inlet flow field onto the noise emission. In many applications where tight packaging is required, a 90° elbow is placed just upstream of the compressor inducer. This can create a distortion of the incoming flow that affects the turbocharger operation; a distortion that is related to the radius of the elbow. In this experimental investigation three 90° elbow inlets are tested, measuring the in-duct sound intensity through acoustic beamforming, the spectral signature of the noise, and the distortion of the high temperature backflow typical of partially stalled conditions by means of thermocouple arrays. Results show that a tighter elbow radius not only impacts efficiency but also increases inlet noise at conditions close to surge. Spectral analysis shows that this increase is mainly produced in the form of a medium frequency broadband noise usually known as `whoosh¿ in the literature. On the other hand, effect on the outlet is less noticeable. Measurements of the recirculated backflow distortion in terms of circumferential skewness show good correlation with whoosh noise increase, indicating that flow distortion caused by tighter elbows at marginal surge conditions facilitates the transmission of whoosh noise oscillations to the inlet duct, worsening the acoustic behaviour of the system., The equipment used in this work has been partially supported by the Spanish Ministerio de Economia y Competitividad through grant DPI2015-70464-R and by FEDER project funds 'Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)' framed in the operational program of unique scientific and technical infrastructure of the Spanish Ministerio de Economia y Competitividad. F. Roig is partially supported through the Programa de Apoyo para la Investigacion y Desarrollo of Universitat Politecnica de Valencia (PAID-01-17).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Numerical Prediction of Inlet Geometry Influence On the In-Duct Acoustics of Small Centrifugal Compressors

  • Broatch, A.|||0000-0001-9991-1039
  • Navarro, Roberto|||0000-0003-2587-4954
  • García-Tíscar, Jorge|||0000-0003-4934-4587
  • Roig, Ferran
[EN] Small centrifugal compressors are employed to boost automotive internal combustion engines or hydrogen fuel cells, amongst other applications. In many scopes, the overall intensity and quality of noise emission is a major concern, so many researchers develop and assess numerical models to predict acoustic spectra. In this work, Detached Eddy Simulations (DES) of a vaneless centrifugal compressor are conducted to assess the impact of intake geometries on its aeroacoustic performance. Experimental measurements are employed as a means of validation. Flow field analysis and Dynamic Mode Decomposition allow us to analyze the underlying mechanisms of the most relevant acoustic features. This work provides insight into the implications for noise generation of employing tight elbows due to packaging constraints., Spanish Ministerio de-Economia y Competitividad (Grant No. DPI2015-70464-R; Funder ID: 10.13039/501100003329).Programa de-Apoyo para la Investigacion y Desarrollo of the Universitat Politecnica de-Valencia (Grant No. PAID-01-17; Funder ID: 10.13039/501100004233).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Prediction of flow induced vibration of a flat plate located after a bluff wall mounted obstacle

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Gil, A.|||0000-0001-7192-6992
  • Quintero-Igeño, Pedro-Manuel|||0000-0003-4373-2079
  • Ammirati, A.
  • Denayer, H.
  • Desmet, W.
[EN] Accurate prediction of Flow Induced Vibration phenomena is currently a field of major interest due to the use of lightweight materials in the automotive and aerospace industry. This article studies the turbulent flow around a wall-mounted obstacle, and the induced deformations produced by the pressure fluctuations on a plate located downstream the obstacle. The methodology used is a combination of experimental tests and numerical simulations. On one side, experiments were carried out in a wind tunnel test facility equipped with Particle Image Velocimetry to characterize the fluid velocity field, and laser vibro-meter to measure the vibrations of the plate. On the other side, Fluid-Structure Interaction (FSI-one-way) has been calculated by considering different turbulence modeling approximations (RANS and LES). Finally, numerical results have been analyzed and validated against the experiments in terms of main flow structures and the vibroacoustic response of the plate., This work has been partially supported by Universitat Politecnica de Valencia through the grant Programa de apoyo a la Carrera Academica del Profesorado 2018/03/14 and by the Spanish Ministerio de Economia y Competitividad through Grant No. DPI2015-70464-R. The computational resources and services used in this work were provided by the VSC (Flemish Supercomputer Center), funded by the Research Foundation Flanders and the Flemish Government department EWI. The Research Fund KU Leuven and the Flanders Innovation and Entrepreneurship Agency, within the SILENCEVENT project, are gratefully acknowledged for their support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Impact of gasoline and Diesel blends on combustion noise and pollutant emissions in Premixed Charge Compression Ignition engines

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Broatch, A.|||0000-0001-9991-1039
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
  • Monico Muñoz, Luisa Fernanda
[EN] Research efforts in the automotive sector focus on developing new combustion concepts for mitigating the emissions of nitrous oxides and soot of conventional Diesel combustion. One of the most promising concept is the Premixed Charge Compression Ignition. In this, the fuel burns in premixed conditions, avoiding the formation of soot whereas nitrous oxides are controlled using large amounts of exhaust gas recirculation. Because of the premixed combustion, high fuel-burning velocities are produced, whence combustion noise is deteriorated. In order to mitigate this drawback, different blends of gasoline and Diesel fuels are being considered due to their suitability for this combustion characteristics. The effect of these fuel blends on emissions, performance and engine noise is analysed in this paper with the aim to provide additional knowledge of the fundamental issues of this particular combustion mode. The study also includes sweeps of both the start of injection and the amount of exhaust gas recirculation, in order to evaluate further degrees of freedom in the optimisation of the engine settings. Results show that the consideration of the engine noise together with both performance and emissions, reduces dramatically the margin of variation of the combustion settings, limiting therefore the operation range of the engine. (C) 2017 Elsevier Ltd. All rights reserved., The equipment used in this work has been partially supported by the Spanish Ministerio de Economía y Competitividad through grant no DPI2015-70464-R and by FEDER project funds Dotación de infraestructuras científico técnicas para el Centro Integral de Mejora Energética y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06) framed in the operational program of unique scientific and technical infrastructure of the Spanish Ministerio de Economía y Competitividad. J. Gomez-Soriano is partially supported through contract FPI-S2-2016-1353 of the Programa de Apoyo para la Investigación y Desarrollo (PAID-01-16) of Universitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Local flow measurements in a turbocharger compressor inlet

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Broatch, A.|||0000-0001-9991-1039
  • Margot , Xandra|||0000-0002-2639-0444
  • García-Tíscar, Jorge|||0000-0003-4934-4587
  • Narvekar, Y.
  • Cheung, R.
[EN] This paper describes an experimental study carried out with the objective of characterizing flow instabilities in turbocharger compressors, specially the distribution of the high-temperature compressed back flow that appears upstream of the impeller at marginal surge conditions. The inlet of a test compressor was fitted with linear and circumferential thermocouple arrays in order to measure the temperature distribution caused by this backflow, whose independence of duct wall temperature was validated through thermographic imaging. Miniaturized pressure probes at the inducer and diffuser showed how pressure spectra varied during the different operating conditions. In-duct acoustic intensity was measured in both the inlet and the outlet to investigate the correlation between a known super synchronous broadband issue known as whoosh noise and the backflow behaviour as characterized by local pressure and temperature. Analysis of the results points to inlet whoosh noise being boosted by this reversed flow but not caused by it, the source probably being located at or downstream of the compressor impeller., This work has been partially supported by Jaguar Land Rover Limited, Abbey Road, Whitley, Coventry CV3 4LF, UK. The equipment used in this work has been partially supported by the Spanish Ministerio de Economía y Competitividad through the grant no DPI2015-70464-R and by FEDER project funds “Dotaciön de infraestructuras científico técnicas para el Centro Integral de Mejora Energética y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)” framed in the operational program of unique scientific and technical infrastructure of the Spanish Ministerio de Economía y Competitividad. J. García-Tíscar is partially supported through contract FPI-S2-2015-1530 of the Programa de Apoyo para la Investigación y Desarrollo (PAID) of Universitat Politécnica de Valéncia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Numerical Methodology for Optimization of Compression-Ignited Engines Considering Combustion Noise Control

  • Broatch, A.|||0000-0001-9991-1039
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
  • Pinaki, Pal
  • Som, Sibendu
[EN] It is challenging to develop highly efficient and clean engines while meeting user expectations in terms of performance, comfort and drivability. One of the critical aspects in this regard is combustion noise control. Combustion noise accounts for about 40 percent of the overall engine noise in typical turbocharged diesel engines. The experimental investigation of noise generation is difficult due to its inherent complexity and measurement limitations. Therefore, it is important to develop efficient numerical strategies in order to gain a better understanding of the combustion noise mechanisms. In this work, a novel methodology was developed, combining computational fluid dynamics (CFD) modeling and genetic algorithm (GA) technique to optimize the combustion system hardware design of a high-speed direct injection (HSDI) diesel engine, with respect to various emissions and performance targets including combustion noise. The CFD model was specifically set up to reproduce the unsteady pressure field inside the combustion chamber, thereby allowing an accurate prediction of the acoustic response of the combustion phenomena. The model was validated by simulating several steady operating conditions and comparing the numerical results against experimental data, in both temporal and frequency domains. Thereafter, a GA optimization was performed with the goal of minimizing indicated specific fuel consumption (ISFC) and combustion noise, while restricting pollutant (soot and NOx) emissions to their respective baseline values. Eight design variables were selected pertaining to piston bowl geometry, nozzle inclusion angle, number of injector nozzle holes and in-cylinder swirl. An objective merit function based on the emissions, ISFC and combustion noise, was constructed to quantify the strength of the engine designs, and was determined using the CFD model as the function evaluator. The in-cylinder noise level was characterized by the total resonance energy of local pressure oscillations. The optimum engine configuration thus obtained, showed a significant improvement in terms of efficiency and combustion noise compared to the baseline system, along with both soot and NOx emissions within their respective constraints. This optimum configuration included a deeper and tighter bowl geometry with higher swirl and larger number of nozzle holes. Subsequently, a more detailed acoustics analysis based on proper orthogonal decomposition (POD) technique was carried out to further explore the combustion noise benefits achieved by the GA optimum. This computational study is a first of its kind (to the best of the authors¿ knowledge), which demonstrates a comprehensive framework to incorporate combustion noise into a numerical optimization strategy for engine design., The equipment used in this work was partially supported by FEDER and the Spanish Government through grant no. DPI2015-70464-R and by Fondo Europeo de Desarrollo Regional (FEDER) project funds "Dotacion de infraestructuras cientifico tecnicas para el Centro Integral de Mejora Energetica y Medioambiental de Sistemas de Transporte (CiMeT), (FEDER-ICTS-2012-06)," framed in the operational program of unique scientific and technical infrastructure of the Spanish Ministerio de Economia y Competitividad. J. Gomez-Soriano was partially supported through contract FPI-S2-2016-1353 of the "Programa de Apoyo para la Investigacion y Desarrollo (PAID-01-16)" of Universitat Politecnica de Valencia. The submitted manuscript was created partly by UChicago Argonne, LLC, Operator of Argonne National Laboratory. Argonne, a US Department of Energy (DOE) Office of Science laboratory, is operated under Contract No. DE-AC02-06CH11357. This research was partly funded by the US DOE Office of Vehicle Technologies, Office of Energy Efficiency and Renewable Energy under Contract No. DE-AC02-06CH11357. The authors wish to thank Gurpreet Singh and Leo Breton, program managers at DOE, for their support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Dynamic mode decomposition of the acoustic field in radial compressors

  • Broatch, A.|||0000-0001-9991-1039
  • García-Tíscar, Jorge|||0000-0003-4934-4587
  • Roig-Villanueva, Ferran
  • Sharma, Sidharath
[EN] Widely recognized since the beginning of air travel as a major issue, noise reduction remains nowadays a pressing concern for all stakeholders in the aviation industry. While aeroengine compressors, specially at the approach phase, have been historically identified as a leading source of noise, most of the research has been conducted on compressors of the axial type. However, radial compressors are found in a wide array of applications: smaller business jets, helicopters, unmanned aerial vehicles (UAVs), auxiliary power units (APUs), turbochargers for reciprocating engines, etc. Owing to their geometrical particularities, radial compressors feature flow patterns that differ from their axial counterparts, leading to different acoustic performance but also opening the door for different optimization approaches. Yet, classical modal decomposition techniques focused on duct propagation may fail to reveal the complex interactions between geometry and flow features that act as noise sources. In this paper we apply, in addition to the classical approach, a data-driven Dynamic Mode Decomposition (DMD) to pressure data coming from a Detached Eddy Simulation (DES), in which we have experimentally validated the correct reproduction of the modal behaviour of the compressor, thus obtaining in-depth details of the link between flow phenomena and noise generation and transmission across the inlet and outlet ducts. (C) 2019 Elsevier Masson SAS. All rights reserved., The equipment used in this work has been partially supported by the Spanish Ministerio de Economía y Competitividad through grant [DPI2015-70464-R] and by FEDER project funds Dotación de infraestructuras científico técnicas para el Centro Integral de Mejora Energética y Medioambiental de Sistemas de Transporte (CiMeT), [FEDER-ICTS-2012-06] framed in the operational program of unique scientific and technical infrastructure of the Spanish Ministerio de Economía y Competitividad. F. Roig is supported through the Programa de Apoyo para la Investigación y Desarrollo of the Universitat Politècnica de València [PAID-01-17].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Prediction of the transmission loss in a flexible chamber

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Gil, A.|||0000-0001-7192-6992
  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
  • Quintero-Igeño, Pedro-Manuel|||0000-0003-4373-2079
  • F. D. Denia|||0000-0003-4536-8610
[EN] Acoustic components have been extensively studied supposing perfectly rigid behavior. Although some works have been performed for the radiated sound in the case of a flexible element, an important lack of information exists concerning transmission loss analysis. The current investigation proposes the study for a generic flexible expansion chamber. The analysis has been performed using two different methods: a resolution in the time domain, using a Finite Volume discretization for the fluid domain and a Finite Element discretization for the solid domain, and an approach in the frequency domain, using a Finite Element discretization for both fluid and solid. After studying the rigid case in order to tune up the simulation, the study of the flexible case shows a good agreement among both methods. The comparison of rigid and flexible expansion chambers shows the importance of accounting for these phenomena when the frequency content of the acoustic signal excites the natural modes of the structure., This work has been partially supported by the Spanish Ministerio de Economia y Competitividad through Grant No. DPI2015-70464-R and Generalitat Valenciana by means of project Prometeo/2016/007.