Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Sustainable Production of Drug-Loaded Particles by Membrane Emulsification

  • Albisa, A.
  • Piacentini, E.
  • Arruebo, M.
  • Sebastian, V.
  • Giorno, L.
As the field of drug delivery is expanding into consumer products, it is essential to advance in the development of efficient synthesis technologies while preserving, at the same time, human health and the environment for future generations. Here, the sustainable development of polymeric particles for drug delivery is described. Poly(ethylene glycol) methyl ether-block-poly(lactide-co-glycolide) based particles containing dexamethasone were produced by membrane emulsification-solvent diffusion methods. The ability of the synthesis process to control particle-size distribution and morphology and its green impactful (energy consumption, simple (sEF) and complete (cEF) E factor) were evaluated. Particles with sufficiently narrow distribution in their droplet size and mean diameter similar to the membrane pore diameter were produced by increasing the dispersed phase flux to 12.84 L h-1 m-2, minimizing the maximum shear stress to 1.12 Pa and the energy consumption to 3.96 × 105 J m-3. The impact of the solvent used on size distribution, particles morphology and green performance scores was also studied. More uniform particles, with dense and slightly rough surface, high encapsulation efficiency and drug loading were obtained by replacing dichloromethane with ethyl acetate. The E factor was also decreased by 80%. Results demonstrated that membrane emulsification is an environmentally improved method for the production of drug delivery systems with enormous impact in terms of formulation quality, energy consumption reduction and waste minimization.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Towards the dehydration of ethanol using pervaporation cross-linked poly (vinyl alcohol)/graphene oxide membranes

  • Castro-Muñoz, Roberto
  • Buera-Gonzalez, Juan
  • Iglesia, Óscar de la
  • Galiano, Francesco
  • Fila, Vlastimil
  • Malankowska, Magdalena
  • Rubio, César
  • Figoli, Alberto
  • Tellez, Carlos
  • Coronas, Joaquín
Highly hydrophilic inorganic material graphene oxide (GO) was successfully prepared and incorporated into a cross-linked poly(vinyl alcohol) (PVA) matrix. The obtained mixed matrix membranes (MMMs) have been used for the dehydration of ethanol (10: 90% water-ethanol) by pervaporation (PV), monitoring their performance in terms of total permeate flux, partial components fluxes, as well as their separation factor. The effect of filler was analyzed by doubling the GO content (at 0.5, 1.0, and 2.0 wt%) in the MMMs. A complete analysis of the operating temperature (between 40 and 70 degrees C) was carried out by means of Arrhenius relationship. Moreover, the membranes were characterized by field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), differential scanning calorimetry (DSC), thermo-gravimetric analysis (TGA), X-ray diffraction (XRD), Fourier transformed infrared spectroscopy (FTIR), measurements of degree of swelling (uptake), water contact angle (CA) and mechanical properties. At 40 degrees C, the best performance was provided by the MMMs containing 1 wt% GO, showing a separation factor of 263 and a permeate flux of about 0.137 kg m(-2) h(-1) (in which 0.133 kg m(-2) h(-1) corresponds to water). This represents a 75% enhancement of the original permeation rate of pristine cross-linked PVA membranes. Taking into account the promising results, it is likely that these MMMs will provide featured benefits in green processes, e.g. ethanol purification by means of less-energy consumption.