Skip to main content

Diseño de materiales nanoestructurados para aplicaciones energéticas

FJC2018-036746-I

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de Promoción del Talento y su Empleabilidad en I+D+i
Subprogram Subprograma Estatal de Formación
Call Juan de la Cierva Formación
Call year 2018
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSIDAD DE OVIEDO

Resultados relacionados

Resultados totales (Incluyendo duplicados): 7
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Nanostructured BaCo0.4Fe0.4Zr0.1Y0.1O3-δ cathodes with different microstructural architectures

  • Santos-Gómez, Lucía dos
  • Zamudio-García, Javier
  • Porras-Vázquez, Jose Manuel
  • Losilla, Enrique R.
  • Marrero-López, David
This article belongs to the Special Issue 10th Anniversary of Nanomaterials—Recent Advances in Nanomaterials for Energy and Catalysis., Lowering the operating temperature of solid oxide fuel cells (SOFCs) is crucial to make this technology commercially viable. In this context, the electrode efficiency at low temperatures could be greatly enhanced by microstructural design at the nanoscale. This work describes alternative microstructural approaches to improve the electrochemical efficiency of the BaCo0.4Fe0.4Zr0.1Y0.1O3-δ (BCFZY) cathode. Different electrodes architectures are prepared in a single step by a cost-effective and scalable spray-pyrolysis deposition method. The microstructure and electrochemical efficiency are compared with those fabricated from ceramic powders and screen-printing technique. A complete structural, morphological and electrochemical characterization of the electrodes is carried out. Reduced values of area specific resistance are achieved for the nanostructured cathodes, i.e., 0.067 Ω·cm2 at 600 °C, compared to 0.520 Ω·cm2 for the same cathode obtained by screen-printing. An anode supported cell with nanostructured BCFZY cathode generates a peak power density of 1 W·cm−2 at 600 °C., This research was funded by Ministerio de Ciencia, Innovación y Universidades (Spain), grant number RTI2018-093735-B-I00 and UMA18-FEDERJA-033.Lucía dos Santos-Gómez thanks the Ministerio de Ciencia, Innovación y Universidades for her Juan de la Cierva Formación grant (FJC2018-036746-I)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Investigation of PO43− oxyanion-doping on the properties of CaFe0.4Ti0.6O3−δ for potential application as symmetrical electrodes for SOFCs

  • Santos-Gómez, Lucía dos
  • Porras-Vázquez, Jose Manuel
  • Losilla, Enrique R.
  • Marrero-López, David
  • Slater, Peter R.
CaTi0.6-xFe0.4PxO3-δ (0≤x ≤ 0.075) perovskite series are investigated as potential symmetrical electrodes for SOFCs. Pure phase compounds with a cubic perovskite structure (s.g. Pm3m) are obtained for x ≤ 0.025, while higher doping level leads to the formation of Ca10(PO4)6(OH)2 as secondary phase. The P-doped compounds are structurally stable under reducing atmosphere unlike the undoped phase. Conductivity values of the P-doped samples are slightly higher than that of the undoped one, i.e. 0.11 and 0.07 Scm−1 for CaTi0.575Fe0.4P0.025O3-δ and CaTi0.6Fe0.4O3-δ, respectively, at 750 °C in air. The performance of CaTi0.575Fe0.4P0.025O3-δ acting simultaneously as both anode and cathode was also tested in a symmetrical solid oxide fuel cell with a 240 μm thick YSZ electrolyte. Hence, these results show that PO43− units can be introduced into CaTi0.6Fe0.4O3-δ perovskite structure, having beneficial effects on the electrochemical performance and the phase stability., This work was supported by Ministerio de Ciencia, Innovación y Universidades through the RTI2018-093735-B-I00 and UMA18-FEDERJA-033 research projects (Spain). L. dos Santos-Gómez thanks to the Ministerio de Ciencia, Innovación y Universidades for her Juan de la Cierva Formación grant (FJC2018-036746-I). J.M. Porras-Vázquez thanks the University of Málaga for his funding., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Nuevos materiales compuestos basados en silicio-xerogel para baterías de ion litio

  • Santos-Gómez, Lucía dos
  • Montes Morán, Miguel Ángel
  • García, José R.
  • García-Granda, Santiago
  • García Suárez, Ana Beatriz
  • Arenillas de la Puente, Ana
Resumen del trabajo presentado al V Workshop de la Red E3TECH / I Workshop Iberoamericano a Distancia E3TECH: “Aplicaciones Medioambientales y Energéticas de la Tecnología Electroquímica”, celebrado de forma telemática del 28 al 31 de octubre de 2020., Este trabajo ha sido financiado por el Ministerio de Economia, Industria y Competitividad de España (CTQ2017-87820-R y MAT2016-78155-C2-1-R) y El Principado de Asturias (FICYT-FEDER: IDI/2018/000118 y IDI/2018/000170). Lucía dos Santos-Gómez agradece al Ministerio de Ciencia, Innovación y Universidades por su beca Juan de la Cierva Formación (FJC2018-036746-I)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Graphene aerogels: A simultaneous combination of both high porosity and large electrical conductivity in a single material

  • Santos-Gómez, Lucía dos
  • Montes Morán, Miguel Ángel
  • Menéndez Díaz, José Ángel
  • García, José R.
  • García-Granda, Santiago
  • Arenillas de la Puente, Ana
Trabajo presentado a la 2nd International Online-Conference on Nanomaterials (IOCN), celebrada del 15 al 30 de noviembre de 2020., This work has been supported by CTQ2017-87820-R, MAT2016-78155-C2-1-R, IDI/2018/000118 and IDI/2018/000170 research grant (Spain). L. dos Santos-Gómez thanks the Ministerio de Ciencia, Innovación y Universidades for her Juan de la Cierva Formación grant (FJC2018-036746-I)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Recent progress in nanostructured electrodes for solid oxide fuel cells deposited by spray pyrolysis

  • Santos-Gómez, Lucía dos
  • Zamudio-García, Javier
  • Porras-Vázquez, Jose Manuel
  • Losilla, Enrique R.
  • Marrero-López, David
Low-temperature solid oxide fuel cells (LT-SOFCs), operating below 650 °C, are attracting a great interest due to their long-term stability and potential application for stationary and portable power generation. Much effort is being devoted to investigating new electrode materials because the electrode polarization resistance remains a serious limitation to the performance. Nanostructured electrodes offer the possibility of increasing the SOFC efficiency at low temperatures. Among the different electrode preparation techniques, spray pyrolysis deposition is a versatile, economic and industrially scalable method to grow electrodes directly on the electrolyte, reducing preparation steps and time. Recent progresses in this field are summarized here, especially highlighting the wide variety of different microstructural strategies used to improve the electrode performance, i.e. nanocomposite cathodes graded cathodes, infiltrated cathodes and cathodes with active/functional layers. Finally, the current existing challenges and the future working directions for further enhancing the properties of new nanostructured electrodes are discussed., This work was supported by Ministerio de Ciencia, Innovación y Universidades through the RTI2018-093735-B-I00 and UMA18-FEDERJA-033 research projects (Spain). L. dos Santos-Gómez and J. Zamudio-García thanks the Ministerio de Ciencia, Innovación y Universidades for the Juan de la Cierva Formación (FJC2018-036746-I) and FPU (FPU17/02621) grants, respectively., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Structural and proton conductivity studies of fibrous π-Ti2O(PO4)2·2H2O: application in chitosan-based composite membranes

  • Babaryk, Artem A.
  • Adawy, Alaa
  • García, Inés
  • Trobajo, Camino
  • Amghouz, Zakariae
  • Colodrero, Rosario M. P.
  • Cabeza, Aurelio
  • Olivera-Pastor, Pascual
  • Bazaga-García, Montse
  • Santos-Gómez, Lucía dos
Although the fibrous polymorphic modification of titanium phosphate, π-Ti2O(PO4)2·2H2O (π-TiP) has been known for decades, its crystal structure has remained unsolved. Herewith, we report the crystal structure of π-TiP at room temperature, as determined from synchrotron radiation powder X-ray diffraction, and corroborated by 31P solid state NMR and accurate density functional theory calculations. In contrast to the previously reported ρ-TiP polymorph, the as-synthesized hydrated phase crystallizes in the monoclinic system (P21/c, a = 5.1121(2) Å, b = 14.4921(9) Å, c = 12.0450(11), β = 115.31(1)°, Z = 4), and is composed of corner-sharing titanium octahedra and phosphate units arranged in a pattern that is unique to the ρ-TiP polymorph. The unit cell was confirmed by electron diffraction, while the formation of planar packing imperfections and stacking faults along the [101] plane was revealed by HRTEM analysis. An in situ dehydration study of π-TiP, monitored by high-temperature powder X-ray diffraction, led to a new anhydrous monoclinic (P21/c, a = 5.1187(13) Å, b = 11.0600(21) Å, c = 14.4556(26), β = 107.65(2)°, Z = 4) phase that crystallizes at 500 °C. The latter resembles the packing fashion of the parental π-TiP, albeit titanium atoms are present in both distorted tetrahedral and octahedral coordination environments. Anhydrous π-TiP was found to partially rehydrate at room temperature, reversibly adopting the structure of the initial phase. The studies carried out under different conditions of leaching and impregnation with H3PO4 showed that π-TiP exhibits an extrinsic proton conductivity (1.3 × 10−3 S cm−1 at 90 °C and 95% RH) due to the presence of the protonated phosphate species bound on the particles surface, as revealed by 31P MAS-NMR spectroscopy data. The composite membranes of Chitosan (CS) matrices filled with H3PO4-impregnated π-TiP solid show an increment of proton conductivity up to 4.5 × 10−3 S cm−1, at 80 °C and 95% RH, which is 1.8-fold higher than those of the bare CS membranes., This work has been supported by Ministerio de Ciencia, Innovación y Universidades and Ministerio de Economía, Industria y Competitividad from Spain (MAT2016-78155-C2-1-R, MAT2016-77648-R and PID2019-110249RB-I00), Junta de Andalucía (FQM-113) research project and Principado de Asturias–FICYT-FEDER (IDI/2018/000170). Use of the Advanced Photon Source at Argonne National Laboratory was supported by the U. S. Department of Energy, Office of Science, Office of Basic Energy Sciences, under Contract No. DE-AC02-06CH11357. Artem A. Babaryk would like to thank Prof. Santiago García-Granda (SYSTAM Group), the Department of Physical and Analytical Chemistry, University of Oviedo, for the SRPXRD data (APS 11 BM-B “Mail-In” program, under proposal no. GUP-65338). Prof. José Manuel Recio (MALTA-Consolider Team) is acknowledged for providing computational facilities at the University of Oviedo. The authors thank Prof. José R. García and S. Khainakov, Department of Organic and Inorganic Chemistry, University of Oviedo, for their generous scientific assistance. L. dos Santos-Gómez thanks the Ministerio de Ciencia, Innovación y Universidades for her Juan de la Cierva Formación grant (FJC2018-036746-I), M. Bazaga-García thanks Junta de Andalucía for her Postdoc PAIDI grant, and R. M. P. Colodrero thanks UMA Research Plan for her financial support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Ultralight-weight graphene aerogels with extremely high electrical conductivity

  • Santos-Gómez, Lucía dos
  • García, José R.
  • Montes Morán, Miguel Ángel
  • Menéndez Díaz, José Ángel
  • García-Granda, Santiago
  • Arenillas de la Puente, Ana
The integration of 2D graphene sheets into a porous and macroscopic structure is extremely attractive for application in several electrochemical fields. In this regard, for the first time, the synthesis of 3D graphene aerogels is reported by using a rapid, easy, cost-effective, and scalable at industrial level methodology. These aerogels integrate the intrinsic properties of graphene with a high pore volume. To achieve this ultraporous graphene network, resorcinol/formaldehyde polymer with controllable porosity is employed as a binder and a cross-linker material, and a graphene oxide solution provides the graphene building blocks. Two series of materials with and without catalyst for resorcinol/formaldehyde reaction and with different synthesis conditions and graphene contents are studied. The resulting graphene aerogels present low density, large macroporosity, and electrical conductivity values as high as 852 S m−1, with 97.58% of porosity, which is the highest value of electrical conductivity reported so far in the literature for ultralight-weight graphene aerogels., This work was supported by the Ministerio de Economía, Industria y Competitividad from Spain (CTQ2017-87820-R and MAT2016-78155-C2-1-R) and Principado de Asturias—FICYT-FEDER (IDI/2018/000118 and IDI/2018/000170). L.d.S.-G. thanks the Ministerio de Ciencia, Innovación y Universidades for her Juan de la Cierva Formación grant (FJC2018-036746-I)., Peer reviewed