Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 16
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Vertically Averaged and Moment Equations for Dam-Break Wave Modeling: Shallow Water Hypotheses

  • Cantero-Chinchilla, Francisco N.
  • Gamero, Pedro
  • Castro-Orgaz, Oscar
  • Cea, Luis
  • Hager, Willi H.
  • Bergillos-Meca, Rafael Jesús|||0000-0001-8674-5043
[EN] The dam-break wave modeling technology relies upon the so-called shallow water equations (SWE), i.e., mass and momentum vertically averaged equations by implementing the shallow water hypotheses, namely (i) horizontal velocity component independent of the vertical coordinate, (ii) vertical velocity component is null, (iii) pressure distribution is hydrostatic, (iv) turbulence is neglected. While this model often yields a satisfactory answer from an engineering standpoint, flows with vertical length scales not negligible cannot be modeled with accuracy, including the undular surge generated after a dam break for relatively high tailwater levels. These flows are modeled by the Serre-Green-Naghdi equations (SGNE), which fail to mimic wave breaking for low tailwater levels, however. Neither SWE nor SGNE produce a fully satisfactory answer for modeling dam break waves, therefore. A higher-order model using vertically averaged and moment equations (VAM) is used in this work to simulate dam break waves, thereby showing good results for arbitrary values of the tailwater level. The model contains four perturbation parameters implemented to overcome the shallow water hypotheses; two for the velocity components and two for fluid pressure. The role of each parameter in relaxing the limitations of the SWE is systematically investigated, depicting a complex and necessary interplay between the dynamic component of fluid pressure and the modeling of the velocity profile in producing accurate solutions for both non-hydrostatic and broken waves in dam break flows. The results highlight how the shallow water hypotheses can be relaxed in the vertically averaged modeling of dam break waves, producing an outcome of both theoretical and practical interest in the field. The results generated are tested with available experimental data, resulting in acceptable agreement., This research was funded by the Spanish State Research Agency; project number CTM2017-85171-C2-1-R. FNCC and RB were partly funded by the Spanish Ministry of Science, Innovation and Universities through the research contracts FJCI-2016-28009 and FJCI-2017-31781, respectively.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Nearshore coastal flow processes using weighted-averaged equations

  • Cantero-Chinchilla, Francisco N.
  • Castro-Orgaz, Oscar
  • Bergillos-Meca, Rafael Jesús|||0000-0001-8674-5043
[EN] This work uses the weighted residual method to simulate non-hydrostatic flows in ocean and coastal areas in a vertically-averaged framework. A Vertically-Averaged and Moment equations set is developed. The system is solved through a hybrid finite volume-finite difference numerical scheme to tackle the hyperbolic and elliptic parts of the equations. Data of seven challenging tests are used to evaluate the model ability to reproduce non-linearity, dispersion, wave breaking, bore propagation, sheet flow and wave reflection. The tests comprise propagation of sinusoidal waves over a submerged bar; convergence of the numerical scheme; solitary wave transformation over a dry reef flat, a wet reef flat and an exposed reef crest; collision of two solitary waves; and solitary wave reflection on a vertical wall under non-breaking and breaking conditions. The results highlight the accuracy of the model without prescribing any treatment for wave breaking. The conjunction of long and short waves with wave shoaling, run-up and receding flows is accurately reproduced. The model is considered an alternative tool to Boussinesq-type models to solve non-linear flows in the nearshore region, with the advantage of having an automatic mimic of wave breaking due to the field variables used to produce the weighted residual depth-averaged equations., This work was supported by the Spanish research project CTM201785171-C2-1-R. FNCC and RB were partly funded by the Spanish Ministry of Science, Innovation and Universities through Programa Juan de la Cierva 2016 (FJCI-2016-28009) and Programa Juan de la Cierva 2017 (FJCI-2017-31781), respectively. We thank the two anonymous reviewers of this work for the comments offered to improve it.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A MATLAB software platform for modelling vertically-integrated non-hydrostatic flows with moment equations

  • Gamero, Pedro
  • Cantero-Chinchilla, Francisco
  • Castro-Orgaz, Oscar
  • Bergillos-Meca, Rafael Jesús|||0000-0001-8674-5043
[EN] This work presents a software platform to compute depth-integrated non-hydrostatic coastal and open channel flows. The software is based on the Vertically-Averaged and Moment (VAM) equations model. The VAM model uses the weighted residual method to account for the non-hydrostaticity and non-uniformity of flow. After presenting the governing equations, numerical scheme and structure of the graphical user interface, the software is applied to solve coastal and open channel flow tests with significant non-hydrostaticity and non-uniformity of flow. The results are compared with hydrostatic model computations and laboratory measurements. Where a hydrostatic-based simulation poorly reproduces experimental observations, the higher-order model equations by this software platform generate excellent predictions. These findings highlight the potential of this user-friendly software platform for modeling open channel, river and nearshore flows and processes, where non-hydrostatic pressure and non-uniform velocity shall be accounted for, which entails a meaningful advance for the hydraulic community., This work was supported by the research project CTM2017-85171-C2-1-R (Secretaría de Estado de I þ D þ i, Spain) and the research group AGR-127 (Junta de Andalucía). RB and FNCC were partly funded by the Spanish Ministry of Science, Innovation and Universities through Programa Juan de la Cierva 2017 (FJCI-2017-31781) and Programa Juan de la Cierva 2016 (FJCI-2016-28009), respectively.
RUC. Repositorio da Universidade da Coruña
Publication Artículo científico (JournalArticle)

Vertically Averaged and Moment Equations for Dam-Break Wave Modeling: Shallow Water Hypotheses

  • Cantero-Chinchilla, Francisco Nicolás
  • Bergillos, Rafael J.
  • Gamero, Pedro
  • Castro Orgaz, Óscar
  • Cea, Luis
  • Hager, Willi H.
[Abstract] The dam-break wave modeling technology relies upon the so-called shallow water equations (SWE), i.e., mass and momentum vertically averaged equations by implementing the shallow water hypotheses, namely (i) horizontal velocity component independent of the vertical coordinate, (ii) vertical velocity component is null, (iii) pressure distribution is hydrostatic, (iv) turbulence is neglected. While this model often yields a satisfactory answer from an engineering standpoint, flows with vertical length scales not negligible cannot be modeled with accuracy, including the undular surge generated after a dam break for relatively high tailwater levels. These flows are modeled by the Serre–Green–Naghdi equations (SGNE), which fail to mimic wave breaking for low tailwater levels, however. Neither SWE nor SGNE produce a fully satisfactory answer for modeling dam break waves, therefore. A higher-order model using vertically averaged and moment equations (VAM) is used in this work to simulate dam break waves, thereby showing good results for arbitrary values of the tailwater level. The model contains four perturbation parameters implemented to overcome the shallow water hypotheses; two for the velocity components and two for fluid pressure. The role of each parameter in relaxing the limitations of the SWE is systematically investigated, depicting a complex and necessary interplay between the dynamic component of fluid pressure and the modeling of the velocity profile in producing accurate solutions for both non-hydrostatic and broken waves in dam break flows. The results highlight how the shallow water hypotheses can be relaxed in the vertically averaged modeling of dam break waves, producing an outcome of both theoretical and practical interest in the field. The results generated are tested with available experimental data, resulting in acceptable agreement., This research was funded by the Spanish State Research Agency; project number CTM2017-85171-C2-1-R. FNCC and RB were partly funded by the Spanish Ministry of Science, Innovation and Universities through the research contracts FJCI-2016-28009 and FJCI-2017-31781, respectively
Helvia. Repositorio Institucional de la Universidad de Córdoba
Publication Artículo científico (JournalArticle)

Vertically-averaged and moment equations for flow and sediment transport

  • Cantero-Chinchilla, Francisco Nicolás
  • Castro-Orgaz, Oscar
  • Khan, Abdul Aziz
Simulation of river flow processes including sediment transport is usually conducted using the shallow water flow equations, which are based on a hydrostatic pressure distribution. To increase the accuracy of predictions in a variety of scenarios involving horizontal length scales of the order of vertical length scales, an improved repre- sentation of the vertical flow structure is necessary. The mathematical approximation to field variables like the velocity and fluid pressure must be enhanced during the depth-integrating process. Therefore, this paper presents a 1D non-hydrostatic flow and sediment transport model developed by using the method of the weighted residuals into the RANS equations. Using continuity, momentum, and moment equations, the fluid pressure distribution is modelled using a quadratic predictor with perturbation parameters to deviate the vertical momentum balance from the hydrostatic law. The flow equations are a generalized non-hydrostatic flow solver, where the fluid den- sity variation due to suspension of sediments and the bed deformation due to erosion-sedimentation processes are accounted for. A hybrid semi-implicit finite volume-finite difference numerical scheme is developed to solve the system of conservation laws. Two different approaches are used to model the sediment transport processes: (i) Unified computation of the total-load transport and (ii) separate computation of suspended and bed loads. The accuracy of the non-hydrostatic model is demonstrated by comparison with experimental data, highlighting better results accounting for separate determinations of the suspended and bed loads in highly erosive flows.
Helvia. Repositorio Institucional de la Universidad de Córdoba
Publication Artículo científico (JournalArticle)

Nearshore coastal flow processes using weighted-averaged equations

  • Cantero-Chinchilla, Francisco Nicolás
  • Bergillos, Rafael Jesus
  • Castro-Orgaz, Oscar
This work uses the weighted residual method to simulate non-hydrostatic flows in ocean and coastal areas in a vertically-averaged framework. A Vertically-Averaged and Moment equations set is developed. The system is solved through a hybrid finite volume-finite difference numerical scheme to tackle the hyperbolic and elliptic parts of the equations. Data of seven challenging tests are used to evaluate the model ability to reproduce nonlinearity, dispersion, wave breaking, bore propagation, sheet flow and wave reflection. The tests comprise propagation of sinusoidal waves over a submerged bar; convergence of the numerical scheme; solitary wave transformation over a dry reef flat, a wet reef flat and an exposed reef crest; collision of two solitary waves; and solitary wave reflection on a vertical wall under non-breaking and breaking conditions. The results highlight the accuracy of the model without prescribing any treatment for wave breaking. The conjunction of long and short waves with wave shoaling, run-up and receding flows is accurately reproduced. The model is considered an alternative tool to Boussinesq-type models to solve non-linear flows in the nearshore region, with the advantage of having an automatic mimic of wave breaking due to the field variables used to produce the weighted residual depth-averaged equations.
Helvia. Repositorio Institucional de la Universidad de Córdoba
Publication Artículo científico (JournalArticle)

Steady Flow through Gated Circular Culverts: Hydraulic Operation and Experiments

  • Cantero-Chinchilla, Francisco Nicolás
  • Belaud, Gilles
  • Castro-Orgaz, Oscar
  • Mateos, Luciano
Culverts are ubiquitous hydraulic structures used in cross-drainage and agricultural water systems, especially at farm outlets in irrigation systems. Gate control adds hydraulic complexity to culvert water flow, yet it has hardly been studied. This study has two objectives: (1) to classify the operational conditions of gated culverts, and (2) to establish an experimental data set for analyzing discharge relationships based on that classification. A theoretical inlet–outlet control–based classification resulted in 22 inlet control and 19 outlet control cases, organized in 4 inlet and 5 outlet control groups. A total of 230 laboratory tests were conducted. The laboratory setup reproduced the conditions of inlet submerged with outlet in free surface (one of four inlet control groups) and all conditions except inlet in free surface with outlet submerged (four of five outlet control groups) of the inlet and outlet control groups, respectively. Comparison with existing classification schemes for gated culverts confirmed the suitability of the proposed scheme and provided further insight into flow classification. The discharge grouped by narrow ranges of gate openings was found to follow a power-law relationship of head with an exponent between 0 and 1. Flow transition regions between groups of conditions were examined, suggesting parabolic transition curves. The gate opening was found to be the dominant variable, resulting in a direct proportional effect on discharge, i.e., data corresponding to greater gate openings enveloped those with smaller openings. The slope’s influence could not be discerned within the slope range tested. Discharge estimation based on a dimensionless, empirical model produced reasonable results, although its case-dependent nature requires further research to develop operational hydraulic models for determining discharge through gated culverts. Application of the proposed classification scheme could help develop these hydraulic tools with sufficient accuracy.
Helvia. Repositorio Institucional de la Universidad de Córdoba
Publication Artículo científico (JournalArticle)

A MATLAB software platform for modelling vertically-integrated non-hydrostatic flows with moment equations

  • Gamero, Pedro
  • Bergillos, Rafael Jesús
  • Cantero-Chinchilla, Francisco Nicolás
  • Castro-Orgaz, Oscar
This work presents a software platform to compute depth-integrated non-hydrostatic coastal and open channel flows. The software is based on the Vertically-Averaged and Moment (VAM) equations model. The VAM model uses the weighted residual method to account for the non-hydrostaticity and non-uniformity of flow. After presenting the governing equations, numerical scheme and structure of the graphical user interface, the software is applied to solve coastal and open channel flow tests with significant non-hydrostaticity and non-uniformity of flow. The results are compared with hydrostatic model computations and laboratory measurements. Where a hydrostatic-based simulation poorly reproduces experimental observations, the higher-order model equations by this software platform generate excellent predictions. These findings highlight the potential of this user-friendly software platform for modeling open channel, river and nearshore flows and processes, where non-hydrostatic pressure and non-uniform velocity shall be accounted for, which entails a meaningful advance for the hydraulic community.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Vertically-averaged and moment equations for flow and sediment transport

  • Cantero-Chinchilla, Francisco N.
  • Castro-Orgaz, Óscar
  • Khan, Abdul A.
Simulation of river flow processes including sediment transport is usually conducted using the shallow water flow equations, which are based on a hydrostatic pressure distribution. To increase the accuracy of predictions in a variety of scenarios involving horizontal length scales of the order of vertical length scales, an improved representation of the vertical flow structure is necessary. The mathematical approximation to field variables like the velocity and fluid pressure must be enhanced during the depth-integrating process. Therefore, this paper presents a 1D non-hydrostatic flow and sediment transport model developed by using the method of the weighted residuals into the RANS equations. Using continuity, momentum, and moment equations, the fluid pressure distribution is modelled using a quadratic predictor with perturbation parameters to deviate the vertical momentum balance from the hydrostatic law. The flow equations are a generalized non-hydrostatic flow solver, where the fluid density variation due to suspension of sediments and the bed deformation due to erosion-sedimentation processes are accounted for. A hybrid semi-implicit finite volume-finite difference numerical scheme is developed to solve the system of conservation laws. Two different approaches are used to model the sediment transport processes: (i) Unified computation of the total-load transport and (ii) separate computation of suspended and bed loads. The accuracy of the non-hydrostatic model is demonstrated by comparison with experimental data, highlighting better results accounting for separate determinations of the suspended and bed loads in highly erosive flows., This work was supported by the Spanish project CTM2017-85171-C2-1-R. The first author was partly funded by the Spanish Ministry of Science, Innovation and Universities through Programa Juan de la Cierva 2016 (FJCI-2016–28009)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Modelización hidrodinámica del flujo sobre diques de materiales sueltos, Hydrodynamic modelling of overtopping flow over granular dikes

  • Cantero-Chinchilla, Francisco N.
  • Bergillos, Rafael J.
  • Castro-Orgaz, Óscar
[ES] Este trabajo presenta un análisis comparativo entre los últimos avances en el modelado promediado de flujos sobre diques de materiales sueltos. Entre los modelos más relevantes se encuentran: (i) modelos no hidrostáticos con transporte de sedimentos, (ii) modelos hidrostáticos con transporte de sedimentos y movimiento dinámico granular y (iii) modelos hidrostáticos con transporte de sedimentos por carga de fondo. Los tres tipos de modelos son comparados con datos experimentales para discutir su aplicabilidad. Mientras que el modelo hidrostático con transporte de sedimentos por carga de fondo presenta una solución adecuada en términos generales, el modelo no hidrostático permite mejorar la predicción del flujo en la cresta del dique, mientras que el modelo con movimiento granular dinámico permite mejorar las predicciones cerca del pie del dique. Por último, se discuten las limitaciones de los modelos., [EN] This paper presents a comparative analysis of the last advances in depth-averaged modelling of overtopping flow over granular dikes. Among the most relevant models in this field, three families of models are described: (i) non-hydrostatic models with sediment transport, (ii) hydrostatic models with sediment transport and dynamic granular beds, and (iii) hydrostatic models with sediment transport as bed-load. To study their suitability, examples of the three families of models are compared using experimental data of dike overtopping. Whilst the hydrostatic model with bed-load sediment transport shows a fair agreement with the experimental data, the results by the non-hydrostatic model produces a more accurate free surface profile up to the dike crest domain. The results by the hydrostatic model assuming dynamic bed deformation enhances the predictions near the dike toe downstream. Finally, the limitations of the models are discussed., Este trabajo ha sido financiado por el Ministerio de Ciencia, Innovación y Universidades a través del proyecto de investigación CTM2017-85171-C2-1-R, el Programa Juan de la Cierva 2016 (FJCI-2016-28009) y el Programa Juan de la Cierva 2017 (FJCI-2017-31781)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Vertically Averaged and Moment Equations for Dam-Break Wave Modeling: Shallow Water Hypotheses

  • Cantero-Chinchilla, Francisco N.
  • Bergillos, Rafael J.
  • Gamero-Ojeda, Pedro
  • Castro-Orgaz, Óscar
  • Cea, Luis
  • Hager, Willi H.
The dam-break wave modeling technology relies upon the so-called shallow water equations (SWE), i.e., mass and momentum vertically averaged equations by implementing the shallow water hypotheses, namely (i) horizontal velocity component independent of the vertical coordinate, (ii) vertical velocity component is null, (iii) pressure distribution is hydrostatic, (iv) turbulence is neglected. While this model often yields a satisfactory answer from an engineering standpoint, flows with vertical length scales not negligible cannot be modeled with accuracy, including the undular surge generated after a dam break for relatively high tailwater levels. These flows are modeled by the Serre–Green–Naghdi equations (SGNE), which fail to mimic wave breaking for low tailwater levels, however. Neither SWE nor SGNE produce a fully satisfactory answer for modeling dam break waves, therefore. A higher-order model using vertically averaged and moment equations (VAM) is used in this work to simulate dam break waves, thereby showing good results for arbitrary values of the tailwater level. The model contains four perturbation parameters implemented to overcome the shallow water hypotheses; two for the velocity components and two for fluid pressure. The role of each parameter in relaxing the limitations of the SWE is systematically investigated, depicting a complex and necessary interplay between the dynamic component of fluid pressure and the modeling of the velocity profile in producing accurate solutions for both non-hydrostatic and broken waves in dam break flows. The results highlight how the shallow water hypotheses can be relaxed in the vertically averaged modeling of dam break waves, producing an outcome of both theoretical and practical interest in the field. The results generated are tested with available experimental data, resulting in acceptable agreement., This research was funded by the Spanish State Research Agency; project number CTM2017-85171-C2-1-R. FNCC and RB were partly funded by the Spanish Ministry of Science, Innovation and Universities through the research contracts FJCI-2016-28009 and FJCI-2017-31781, respectively., Peer reviewec
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

A MATLAB software platform for modelling vertically-integrated non-hydrostatic flows with moment equations

  • Gamero-Ojeda, Pedro
  • Bergillos, Rafael J.
  • Cantero-Chinchilla, Francisco N.
  • Castro-Orgaz, Óscar
This work presents a software platform to compute depth-integrated non-hydrostatic coastal and open channel flows. The software is based on the Vertically-Averaged and Moment (VAM) equations model. The VAM model uses the weighted residual method to account for the non-hydrostaticity and non-uniformity of flow. After presenting the governing equations, numerical scheme and structure of the graphical user interface, the software is applied to solve coastal and open channel flow tests with significant non-hydrostaticity and non-uniformity of flow. The results are compared with hydrostatic model computations and laboratory measurements. Where a hydrostatic-based simulation poorly reproduces experimental observations, the higher-order model equations by this software platform generate excellent predictions. These findings highlight the potential of this user-friendly software platform for modeling open channel, river and nearshore flows and processes, where non-hydrostatic pressure and non-uniform velocity shall be accounted for, which entails a meaningful advance for the hydraulic community., This work was supported by the research project CTM2017-85171-C2-1-R (Secretaría de Estado de I + D + i, Spain) and the research group AGR-127 (Junta de Andalucía). RB and FNCC were partly funded by the Spanish Ministry of Science, Innovation and Universities through Programa Juan de la Cierva 2017 (FJCI-2017-31781) and Programa Juan de la Cierva 2016 (FJCI-2016-28009), respectively.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Nearshore coastal flow processes using weighted-averaged equations

  • Cantero-Chinchilla, Francisco N.
  • Bergillos, Rafael J.
  • Castro-Orgaz, Óscar
This work uses the weighted residual method to simulate non-hydrostatic flows in ocean and coastal areas in a vertically-averaged framework. A Vertically-Averaged and Moment equations set is developed. The system is solved through a hybrid finite volume-finite difference numerical scheme to tackle the hyperbolic and elliptic parts of the equations. Data of seven challenging tests are used to evaluate the model ability to reproduce non-linearity, dispersion, wave breaking, bore propagation, sheet flow and wave reflection. The tests comprise propagation of sinusoidal waves over a submerged bar; convergence of the numerical scheme; solitary wave transformation over a dry reef flat, a wet reef flat and an exposed reef crest; collision of two solitary waves; and solitary wave reflection on a vertical wall under non-breaking and breaking conditions. The results highlight the accuracy of the model without prescribing any treatment for wave breaking. The conjunction of long and short waves with wave shoaling, run-up and receding flows is accurately reproduced. The model is considered an alternative tool to Boussinesq-type models to solve non-linear flows in the nearshore region, with the advantage of having an automatic mimic of wave breaking due to the field variables used to produce the weighted residual depth-averaged equations., This work was supported by the Spanish research project CTM2017-85171-C2-1-R. FNCC and RB were partly funded by the Spanish Ministry of Science, Innovation and Universities through Programa Juan de la Cierva 2016 (FJCI-2016-28009) and Programa Juan de la Cierva 2017 (FJCI-2017-31781), respectively.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Vertically-Averaged Coastal Flow Modelling Using Moment Equations

  • Cantero-Chinchilla, Francisco N.
  • Bergillos, Rafael J.
  • Castro-Orgaz, Óscar
Editors: José María Carrillo, Eva Fenrich, David Ferràs, Silke Wieprecht.-- Trabajo presentado en el 1st IAHR Young Professionals Congress, celebrado onlien el 17 y 18 de noviembre de 2020., Among the available type of models in the literature, the vertically-averaged modelling of coastal flow processes is frequently accomplished resorting to Boussinesq-type equations. These models account for non-hydrostatic flow effects through the inclusion of dispersive extra terms in the governing equations, demanding high numerical accuracy while implementing the discrete form of derivatives in these extra terms. An useful alternative to Boussinesq-type models are the Vertically-Averaged and Moment (VAM) equations, where the extra degrees of freedown are mathematically closed in a Galerkin-type framework. This work presents the evaluation ofa VAM model for simulating complex one-dimensional coastal flows. A challenging test comprising non-linear wave propagation, wave breaking, bore propagation and reflection is selected. The accuracy of the results as compared to the experimental data highlights the utility of VAM models as alternative tools to Boussinesq-type models in coastal flow modelling., This work wassupported by the research project CTM2017-85171-C2-1-R (State Research Agency, Spain) and the research group AGR-127. RB and FNCC were partly funded by the Spanish Ministry of Science, Innovation and Universities through research contracts FJCI-2017-31781and FJCI-2016-28009, respectively.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Vertically-Integrated and Moment Equations For Non-Hydrostatic Flow Modelling Matlab Platform

  • Gamero-Ojeda, Pedro
  • Bergillos, Rafael J.
  • Cantero-Chinchilla, Francisco N.
  • Castro-Orgaz, Óscar
Editors: José María Carrillo, Eva Fenrich, David Ferràs, Silke Wieprecht.-- Trabajo presentado en el 1st IAHR Young Professionals Congress, celebrado onlien el 17 y 18 de noviembre de 2020., The majority of the software platforms designed for non-hydrostatic shallow water flow modelling rely on the solution of computational-costly three-dimensional flow models or depth-averaged Boussinesq-type models that require optimization of dispersive terms. In this field, an unexplored but reliable alternative is the Vertically-Averaged and Moment (VAM) equations model. This work presents a MATLAB software platform for one-dimensional non-hydrostatic flow modelling using the VAM model. First, the VAM governing equations are introduced, whichuse the weighted residual method to account for the non-hydrostatic and non-uniform characteristics of flow. Then, the structure of the user-friendly graphical interface is described. Finally, the model is applied to two nearshore and open-channel non-hydrostatic flow tests. The comparison of the results with experimental data highlights the accuracy of the VAM model and the potential of the present software for modelling non-hydrostatic flows., This work was supported by the research project CTM2017-85171-C2-1-R (State Research Agency, Spain) and the research group AGR-127. RB and FNCC were partly funded by the Spanish Ministry of Science, Innovation and Universities through research contracts FJCI-2017-31781 and FJCI-2016-28009, respectively
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Temporal Evolution of Clear-Water Local Scour at Bridge Piers with Flow-Dependent Debris Accumulations

  • Cantero-Chinchilla, Francisco N.
  • Mazza de Almeida, Gustavo Adolfo
  • Manes, Costantino
Previous research has shown that local scour at bridge piers is severely increased by the accumulation of woody debris around piers. However, due to the unavailability of accurate information regarding the characteristics of formed debris jams, the shape and dimensions of accumulations tested in previous laboratory experiments have had to be assumed. This article provides an assessment of debris-induced scour based on recently available knowledge about the relation between the potential dimensions of debris accumulations, the characteristics of flow, and debris elements. Clear-water scour experiments (with and without debris accumulation) were conducted using debris models with shape and size that correspond to the particular flow characteristics of each experiment. The results showed that scour depths obtained with flow-dependent debris accumulations were larger than without accumulations by a factor ranging from 1.18–2.19. The analysis of the scour depths affected by the accumulations suggested similar characteristics as well as dependence on the flow intensity, blockage area ratio, and depth ratio., This research is funded by NERC, grant reference NE/R009015/1. The first author was partly funded by the Spanish Ministry of Science, Innovation and Universities through Programa Juan de la Cierva 2016 (FJCI-2016-28009). The authors would like to thank Dr. Toru Tsuzaki, experimental officer in the Hydraulic laboratory at the University of Southampton, for his assistance during the time this research was accomplished, as well as Mr. Marco Campriani, MSc student at the Politecnico di Torino, who contributed to the experimental campaigns.