Skip to main content

Recubrimientos cerámicos por técnicas de proyección

FJCI-2016-27822

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de Promoción del Talento y su Empleabilidad en I+D+i
Subprogram Subprograma Estatal de Formación
Call Juan de la Cierva Formación
Call year 2016
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Numerical investigation of influence of precursors on transport properties of the jets used in solution precursor plasma spraying

  • Carpio-Cobo, Pablo
  • Pawlowski, Lech
  • Pateyron, Bernard
[EN] The solution precursor plasma spraying is a modification of the conventional plasma spraying technique where the feedstock is a liquid precursor instead of a powder. The phenomena which occur in both techniques are different since the feedstock is liquid and consequently, the jet fragmentation, the solvent evaporation and the chemical reaction or pyrolysis must occur before solid melting and impact onto the substrate. The evaporation of the precursor changes the chemical composition of the plasma plume, hence it implies an important modification in the thermodynamic properties. In the present study, the influence of the solution precursor on these properties, concretely the thermal conductivity and dynamic viscosity of the plasma plume, has been addressed. Then, the ability of heating factor of the plasma plume was estimated and different effects of the precursor on the mentioned transport properties were evaluated. The effect of the type of precursor, the feedstock flow rate and the solution concentration has been evaluated in the present work. It is concluded that all of these variables affect slightly the viscosity but considerably the thermal conductivity and the ability of heating factor. Hence, the selection of the precursor characteristics allows to heat transfer between plasma plume and starting feedstock and consequently the resultant coatings exhibit a lower presence of porous or unmelted material., P. Carpio acknowledges the Valencian Government (APOSTD/2016/040) and the Spanish Ministry of Science, Innovation and Universities for his current post-doc contract (FJCI-2016-27822) for his post-doc contract
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Solution concentration effect on mechanical injection and deposition of YSZ coatings using the solution precursor plasma spraying

  • Carpio-Cobo, Pablo
  • Candidato, Rolando T., Jr.
  • Pawlowski, Lech
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
[EN] YSZ coatings were developed by solution precursor plasma spraying from different solution concentrations. The solutions were characterized and correlated with the rheological properties (specific weight, viscosity and surface tension). The mechanical injection was used therefore a correct injection is essential to get a correct liquid jet break-up inside the plasma plume. The optimal injection pressure must be adjusted for each solution since the solution characteristics affect on the injection process. It was experimentally found out by the observation of the splats' morphology. The particles were not melted at low pressures but solidified prior to the deposition when the injection pressure is high. It was also found out that the optimal static pressure varies with the concentration, but the dynamic pressure is equal for every solution and slightly superior to the dynamic pressure of the plasma plume. After injection optimization, coatings using different solution concentrations were developed and their microstructures were investigated. The liquid jet fragmentations as well as the heat requirements were modified with the concentration so that coating microstructure was affected. The resulting coatings display a lamellar and porous microstructure with the presence of unmelted/unpyrolysed material. Coatings' porosity increased while coatings' grow-up was less intensive when diluted solutions were used as feedstock., This work has been supported by the Spanish Ministry of Economy and Competitiveness (project MAT2015-67586-C3-R). P. Carpio acknowledges the Valencia Government (APOSTD/2016/040) and the Spanish Ministry of Science, Innovation and Universities for his current post-doc contract (FJCI-2016-27822) for his post-doc contract