Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Pine Resin Derivatives as Sustainable Additives to Improve the Mechanical and Thermal Properties of Injected Moulded Thermoplastic Starch

  • Aldas-Carrasco, Miguel Fernando
  • Arrieta, Marina Patricia
  • Pavón-Vargas, Cristina Paola|||0000-0003-2902-0059
  • López-Martínez, Juan|||0000-0001-6904-2282
[EN] Fully bio-based materials based on thermoplastic starch (TPS) were developed starting from corn starch plasticized with glycerol. The obtained TPS was further blended with five pine resin derivatives: gum rosin (GR), disproportionated gum rosin (dehydroabietic acid, RD), maleic anhydride modified gum rosin (CM), pentaerythritol ester of gum rosin (LF), and glycerol ester of gum rosin (UG). The TPS¿resin blend formulations were processed by melt extrusion and further by injection moulding to simulate the industrial conditions. The obtained materials were characterized in terms of mechanical, thermal and structural properties. The results showed that all gum rosin-based additives were able to improve the thermal stability of TPS, increasing the degradation onset temperature. The carbonyl groups of gum rosin derivatives were able to interact with the hydroxyl groups of starch and glycerol by means of hydrogen bond interactions producing a significant increase of the glass transition temperature with a consequent stiffening effect, which in turn improve the overall mechanical performance of the TPS-resin injected moulded blends. The developed TPS¿resin blends are of interest for rigid packaging applications., This research was funded by the Spanish Ministry of Economy and Competitiveness (MINECO), project: PROMADEPCOL (MAT2017-84909-C2-2-R) as well as by Santander-UCM (PR87/19-22628) project. M.A. thanks Secretaria Nacional de Educación Superior, Ciencia, Tecnología e Innovación (SENESCYT-Ecuador) and Escuela Politécnica Nacional. C.P. thanks Santiago Grisolía fellowship (GRISOLIAP/2019/113) from Generalitat Valenciana and M.P.A. thanks MINECO for her postdoctoral contract: Juan de la Cierva-Incorporación (FJCI-2017-33536).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A Deeper Microscopic Study of the Interaction between Gum Rosin Derivatives and a Mater-Bi Type Bioplastic

  • Aldas-Carrasco, Miguel Fernando
  • Arrieta, Marina P.
  • E. Rayón|||0000-0002-0653-2046
  • López-Martínez, Juan|||0000-0001-6904-2282
[EN] The interaction between gum rosin and gum rosin derivatives with Mater-Bi type bioplastic, a biodegradable and compostable commercial bioplastic, were studied. Gum rosin and two pentaerythritol esters of gum rosin (Lurefor 125 resin and Unik Tack P100 resin) were assessed as sustainable compatibilizers for the components of Mater-Bi® NF 866 polymeric matrix. To study the influence of each additive in the polymeric matrix, each gum rosin-based additive was compounded in 15 wt % by melt-extrusion and further injection molding process. Then, the mechanical properties were assessed, and the tensile properties and impact resistance were determined. Microscopic analyses were carried out by field emission scanning electron microscopy (FE-SEM), atomic force microscopy (AFM) and atomic force microscopy with nanomechanical assessment (AFM-QNM). The oxygen barrier and wettability properties were also assayed. The study revealed that the commercial thermoplastic starch is mainly composed of three phases: A polybutylene adipate-co-terephthalate (PBAT) phase, an amorphous phase of thermoplastic starch (TPSa), and a semi-crystalline phase of thermoplastic starch (TPSc). The poor miscibility among the components of the Mater-Bi type bioplastic was confirmed. Finally, the formulations with the gum rosin and its derivatives showed an improvement of the miscibility and the solubility of the components depending on the additive used, This research was funded by Spanish Ministry of Economy and Competitiveness (MINECO), project: PROMADEPCOL (MAT2017-84909-C2-2-R) and M.P.A. s contract: Juan de la Cierva-Incorporación (FJCI-2017-33536).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Improvement of PLA film ductility by plasticization with epoxidized karanja oil

  • Garcia-Garcia, Daniel|||0000-0002-2520-0186
  • López-Martínez, Juan|||0000-0001-6904-2282
  • Samper, María-Dolores|||0000-0002-5102-8412
  • Carbonell-Verdu, A.
  • Arrieta, Marina Patricia
[EN] In this work, karanja oil has been epoxidized and further used as biobased plasticizer to improve some properties of poly (lactic acid) (PLA). The use of epoxidized karanja oil (EKO) has been studied because karanja oil is used in organic farming as an insecticide and generating an epoxidation of the oil can act as a PLA plasticizer. Melt extrusion was used to plasticize PLA with different EKO amounts in the 0e10 wt%. The formulations with EKO decrease the glass transition temperature as the EKO content increases and, in addition, generates an increase in elongation at break. Plasticizer saturation is observed by scanning electron microscopy (SEM) above 5% of EKO. PLA formulation with 5 wt% shows an optimal balance between the improvement of the fragility of the material, improving the elongation at breakage by 77%, using a relatively small concentration of plasticizer. Moreover, all materials were disintegrated under composting conditions at laboratory scale level., This research was supported by the Ministry of Economy and Competitiveness (MINECO) [MAT2017-84909-C2-2-R] and Santander-UCM (PR87/19e22628). D. Garcia-Garcia wants to thanks the Generalitat Valenciana for their financial support through a post-doctoral grant (APOSTD/2019/201). M.P. Arrieta acknowledge for Juan de la Cierva (FJCI-2017-33536) contract from the MINECO.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Enhancing the Thermal Stability of Polypropylene by Blending with Low Amounts of Natural Antioxidants

  • Hernández-Fernández, Joaquín
  • Arrieta, Marina Patricia
  • E. Rayón|||0000-0002-0653-2046
  • López-Martínez, Juan|||0000-0001-6904-2282
[EN] Natural antioxidants are added in very low amounts to protect a polypropylene (PP) matrix against thermo-oxidative degradation during processing. Thus, PP is melt-blended with caffeic, chlorogenic, trans-ferrulic, and p-coumaric acids, and also with flavone and 3-hydroxyflavone at 0.1 wt% with respect to the PP matrix. Neat PP and PP blended with three traditional antioxidants are prepared for comparison. A complete structural, thermal, and mechanical characterization is conducted. Ferrulic acid and particularly caffeic acid increases the thermal stability, showing also the highest activation energy. The structural changes of PP-based films due to the polymer thermal degradation at high temperature (i.e., 400 degrees C) followed by FTIR reveal that antioxidants effectively delay the thermal degradation process. The wettability and the mechanical performance are also studied to get information regarding the industrial application of such films. While caffeic acid provides a more flexible material, ferrulic acid provides higher water resistance. Finally, AFM-QNM shows that PP with caffeic acid has the highest miscibility., This work was supported by the Spanish Ministry of Economy and Competitiveness (MINECO), PROMADEPCOL (MAT2017-84909-C2-2-R). M.P.A. thanks MINECO for Juan de la Cierva-incorporación postdoctoral contract (FJCI-2017-33536).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Electrospinning of PCL-based blends: Processing optimization for their scalable production

  • Arrieta, Marina P.
  • Leonés, Adrián
  • Yusen, M.
  • Kenny, José María
  • Peponi, Laura
In this work poly("-caprolactone) (PCL) based electrospun mats were prepared by blending PCL with microcrystalline cellulose (MCC) and poly(3-hydroxybutyrate) (PHB). The electrospinning processing parameters were firstly optimized with the aim to obtain scalable PCL-based electrospun mats to be used in the industrial sector. Neat PCL as well as PCL-MCC and PCL-PHB based mats in different proportions (99:1; 95:5; 90:10) were prepared. A complete morphological, thermal and mechanical characterization of the developed materials was carried out. Scanning electron microscopy (SEM) observations showed that the addition of PHB to the PCL matrix considerably reduced the formation of beads. Both the addition of MCC and PHB reduced the thermal stability of PCL, but obtained materials with enough thermal stability for the intended use. The electrospun PCL fibers show greatly reduced flexibility with respect to the PCL bulk material, however when PCL is blended with PHB their stretchability is increased, changing their elongation at break from 35% to 70% when 10 wt% of PHB is blended with PCL. However, the mechanical response of the different blends increases with respect to the neat electrospun PCL, offering the possibility to modulate their properties according to the required industrial applications., This work was funded by RYC-2014-15595, FJCI-2017-33536, MAT2017-88123-P and PCIN-2017-036 (FEDER EU).The authors thank the Spanish Ministry of Economy, Industry and Competitiveness (MINEICO) (MAT2017-88123-P, POLYMAGIC: (PCIN-2017-036) cofinanced with EU FEDER funds. M.P.A. and L.P. acknowledge the “Juan de la Cierva” (FJCI-2017-33536) and “Ramon y Cajal” (RYC-2014-15595) contracts from the MINEICO, respectively.