Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of spray/wall impingement using an ECN single-hole injector and a controlled-temperature wall under realistic engine conditions

  • Peraza, Jesús E
  • Payri, Raul|||0000-0001-7428-5510
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Carvallo-García, César Leonardo|||0000-0003-2297-2225
[EN] Spray¿wall interactions (SWI) directly affect fuel¿air mixture and emissions formation. Therefore, they are considered among the most critical physical processes in engine research nowadays. However, the physics of the wall film formation, propagation, and breakup is not fully understood yet. This work aims to use a thermoregulated steel wall to study the spray¿wall interaction phenomenon and its influence on the macroscopic spray behavior. A single-hole injector known as ``Spray D¿¿ in the Engine Combustion Network was used. n-Dodecane was employed as fuel and the wall has been positioned in four different configurations, varying angle and distance respect to the injector tip. For this work, not only diesel combustion is reproduced in the test rig due to ambient gas engine-like thermodynamic conditions, but wall temperature has been controlled to emulate characteristic values that could be found in the piston of an internal combustion engine. This implies that the spray¿wall heat transfer is simulated and its effects on ignition and spray development can be analyzed. Heat flux was measured by employing high-speed thermocouples fitted in the wall and by the use of an one-dimensional transient wall heat model. Three high speed cameras were simultaneously used to observe the SWI, one for the Schlieren optical technique which allows to study the vapor phase of the spray and to determine the ignition delay, another one to observe the natural luminosity of the flame, and finally, an intensified camera was used to determine the lift-off length by observing the chemiluminescence of the OH*. An interesting finding obtained in this work was a boundary layer formation due to the thermal diffusion that contributes to cool down the spray and to delay the high-temperature chemical reactions. Results show a substantial increment of the heat flux and the wall temperature variation with both ambient temperature and density by increasing the flame temperature and gas entrainment. The exposure to the cold wall affects the ignition delay variation with the injection pressure and the wall distance. It was found that the wall temperature (in the range of tested conditions) did not affect the lift-off length location, Authors would like to acknowledge Caterpillar Inc. for its support and interest in this work. The author C. Carvallo thanks the Universitat Politecnica de Valencia for his predoctoral contract (FPI-2019-S1) which is included within the framework of Programa de Apoyo para la Investigacion.. Desarrollo (PAID-01-19). Finally, the collaboration of Omar Huerta Cornejo and Sergi Soro in the laboratory work and the setup of the hardware is greatly thanked.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Engine Combustion Network &quot, Spray G&quot, : Wall heat transfer characterization by infrared thermography

  • Zaccara, Mirko
  • Montanaro, Alessandro
  • Allocca, Luigi
  • Cardone, Gennaro
  • Carvallo-García, César Leonardo|||0000-0003-2297-2225
  • Gimeno, Jaime|||0000-0003-3317-9994
[EN] Nowadays, several efforts are being made to design more efficient, cleaner, and economically accessible engines. Spray-wall interactions are strongly related with the fuel-air mixture and emission formation. As such, they are considered as the most important physical processes in engine research. In the present study, the infrared thermography coupled with an inverse heat transfer data reduction is applied to evaluate the wall heat transfer of an iso-octane spray generated by a multi-hole gasoline direct injector (Spray G) impinging on a heated thin foil. The experimental apparatus includes an Invar foil (50 mu m in thickness) heated by Joule effect and the injector located at 66.66 injector nozzle diameter above the surface. Thermal images of the impinging spray are acquired from the dry side of the foil at several time delays from the start of injection at two different injection pressures (10 and 20 MPa) and two different wall temperatures (373 and 473 K). The experimental data are reduced in the dimensionless form in terms of the spray cooling efficiency zeta, which represents the ratio between the spray cooling heat flux and the heat transfer capability of the fluid, by taking into account the area of impact of the spray. Results show a substantial increment of the heat flux and the spray cooling efficiency by increasing the wall temperature. Also, the increment of the injection pressure has an increasing effect on the area of impact, the heat flux, and the efficiency of the spray for both wall temperatures investigated in the experimental campaign. The spray cone angle and the plume jet axis angle were also estimated from the wall heat flux distribution., The author C. Carvallo thanks the Universitat Politecnica de Valencia for his predoctoral contract (FPI-2019- S1) which is included within the framework of Programa de Apoyo para la Investigacion y Desarrollo(PAID-01-19) and would also like to say thanks for the mobility economical help provided by the program Ayudas para movilidad dentro del Programa para la Formacion de Personal investigador (FPI) de laUPV''.The authors kindly acknowledge Consiglio Nazionale delle Ricerche- STEMS for hardware and technical support. Funding for open access charge: CRUE-Universitat Politecnica deValencia.