Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

ECN Spray G External Spray Visualization and Spray Collapse Description through Penetration and Morphology Analysis

  • Payri, Raul|||0000-0001-7428-5510
  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Marti-Aldaravi, Pedro|||0000-0003-4650-4004
  • Vaquerizo, Daniel
[EN] Inside a DISI engine, a wide range of pressure and temperature conditions are possible, and with the current evolution of the systems, many of the conditions are subject to be encountered at the moment of injection. Given the great differences between Diesel injectors and GDi fuel injectors, the effects of such conditions on the development of the fuel injected can cause phenomena like flash boiling and spray collapse that fundamentally change the behavior of sprays. In this work, the Spray G injector developed by Delphi for the Engine Combustion Network (ECN) group has been tested in a High Pressure High Temperature Constant Pressure Flow Rig (HPHT - CPFR) in a wide range of experimental conditions capturing the liquid and vapor phases of the spray by means of DBI and Schlieren imaging. The work presents the results obtained by spray visualization through comparisons of parametric variations with special focus on the collapse of the spray that occurs under high ambient temperature and density conditions. Spray collapse has been described by showing the direct increase that can cause in spray penetration and the great closing effect that can produce to the aperture of the spray (spray angle). Several contour comparisons using the raw images and the detected contours have been discussed in order to support and further explain the observed trends. (C) 2016 Elsevier Ltd. All rights reserved., This work was sponsored by "Ministerio de Economia y Competitividad" in the frame of the project "Estudio de la interaccion chorro-pared en condiciones realistas de motor (SPRAY WALL)" reference TRA2015-67679-C2-1-R. Daniel Vaquerizo is partially supported through contract FPI-S2-2015-1069 of "Programa de Apoyo para la Investigacion y Desarrollo (PAID)" of Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Study of liquid and vapor phase behavior on Diesel sprays for heavy duty engine nozzles

  • Payri, Raul|||0000-0001-7428-5510
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
  • Vaquerizo, Daniel
A lot of effort has been put in the past years into the understanding of the delivery and development of diesel sprays in engine-like conditions as it has been proved to be a very important step for the design of better and cleaner commercial engines. Due to the bigger share of passenger cars engines over heavy duty engines, the research has been mainly focused on the investigation using small nozzles. This paper studies two nozzles with diameters representative of those that can be encountered in heavy duty engines, with the objective of corroborating the conclusions gathered for small nozzles representative of passenger car engines. The experimental data have been acquired by state-of-the-art techniques and equipment, and serves two purposes: further the understanding of the physics involved in the injection event and spray evaporation; and provide a dataset to CFD models that can accurately predict the behavior of the injection event. The tests were performed in a constant pressure flow vessel that allows to simulate engine-like conditions (1000 K and 15 Mpa) with continuous flow. The injection system tested is a novel, common-rail, solenoid-actuated injector for heavy duty applications which operates up to 220 Mpa. All experiments were performed in non-reacting conditions. The extended test matrix allowed to determine the influence of several parameters such as rail pressure, gas temperature, gas density, and nozzle geometry on the air-fuel mixing and evaporation process, by analyzing the spray penetration and spreading angle. Mie scattering and double-pass Schlieren optical configurations have been used to measure global liquid and vapor penetration, respectively. The data proves that spray penetration at low temperature can be up to 15% faster than spray penetration at high temperature conditions at the same density for the nozzles experi-mented, which limits the usability of low temperature experiments to infer the behavior of the injector at high temperature conditions. The data also shows that the nozzle with the biggest diameter provided the highest value of stabilized liquid length as expected. Also, when vapor phase is reached, the temperature has negligible effect on the global diesel spray morphology, and no influence on the tip penetration or on the spreading angle., This work was sponsored by "Ministerio de Economia y Competitividad" in the frame of the project "Estudio de la interaction chorro-pared en condiciones realistas de motor (SPRAY WALL)" reference TRA2015-67679-c2-1-R. Daniel Vaquerizo is partially supported through contract FPI-S2-2015-1069 of Programa de Apoyo para la Investigacion y Desarrollo (PAID) of Universitat Politecnica de Valencia.