Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental Study of Two Air Management Strategies for Emissions Control in Heavy Duty Engines at Medium to High Loads

  • Bermúdez, Vicente|||0000-0002-2781-5598
  • Molina, Santiago|||0000-0001-7879-2421
  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • Estepa-Ruiz, Daniel
[EN] Different air management strategies, Miller timing and internal EGR (iEGR), have been studied on internal combustion engines with the objective of decreasing NOx emissions. This paper explores heavy duty diesel engine performance by the application of both strategies separately through two different camshaft configurations, mounted and tested in the same engine. On one side, in the case of Miller timing, the early intake valve closing is explored, and on other side, for iEGR, the study is carried out opening the exhaust valve during the intake process. The engine emission and performance study is achieved through the application of a methodology which begins with the selection of the operating points focusing on medium to high loads. It continues with the exploration of different camshaft profiles by mean of a 1D model. Through the 1D model, two camshaft profiles are selected and tested in the test cell, determining the intake valve closing conditions followed by the identification of the thermodynamic behavior during the compression stroke before the injection. Later on, the combustion and emissions formation analysis is performed to conclude with the fuel consumption study for each implemented strategy taking into consideration the important influence of each camshaft profile in the pumping loop. A short discussion on the transient performance effect of each air management strategy completes the scope of the study., Daniel Estepa is partially supported through contract FPI-S2-2015-1091 of Programa de Apoyo para la Investigacion y Desarrollo (PAID) of Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Miller cycle for improved efficiency, load range and emissions in a heavy-duty engine running under reactivity controlled compression ignition combustion

  • Molina, Santiago|||0000-0001-7879-2421
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Estepa-Ruiz, Daniel
[EN] The low temperature, premixed combustion strategies are being investigated in the recent years as a mean to break the NOx-soot trade-off appearing during the diffusive conventional diesel combustion. This approach relies on promoting premixed combustion events with shortened duration, which reduces the heat transfer losses, improves the thermal efficiency, and allows a simultaneous reduction of engine-out NOx and soot emissions. However, since the combustion onset only depends on chemical kinetics, most of these strategies cannot be implemented at medium and high loads due to excessive pressure gradients, which lead to unacceptable noise levels and reliability issues. This experimental work investigates the potential of the Miller cycle as a strategy to minimize the aforementioned challenges when operating under reactivity controlled compression ignition combustion. Moreover, the coupled effect of the Miller cycle with the fuel reactivity modulation is also explored as a way for improving the combustion control. For this purpose, parametric studies varying the effective compression ratio and gasoline fraction have been done in a single-cylinder heavy-duty engine operating at 14 bar indicated mean effective pressure and 1200 rev/min as a baseline condition. The results show that this strategy allows better control of the in-cylinder thermodynamic conditions, enabling a simultaneous reduction of nitrogen oxides and soot emissions down to the EURO VI limits, while keeping a reduced fuel consumption and suitable in-cylinder maximum pressure gradients., The authors thanks VOLVO Group Trucks Technology for supporting this research. The authors also acknowledge the Spanish economy and competitiveness ministry for partially supporting this research (HiReCo TRA2014-58870-R). Daniel Estepa is partially supported through contract FPI-S2-2015-1091 of Programa de Apoyo para la Investigacion y Desarrollo (PAID) of Universitat Politecnica de Valencia.