Skip to main content

Sensores de fibra óptica

IJCI-2017-32476

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de Promoción del Talento y su Empleabilidad en I+D+i
Subprogram Subprograma Estatal de Incorporación
Call Juan de la Cierva Incorporación
Call year 2017
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSIDAD DE ALCALA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Refractive Index and Temperature Sensing Using Inter-Core Crosstalk in Multicore Fibers

  • Madrigal-Madrigal, Javier|||0000-0003-3156-1321
  • Barrera Vilar, David|||0000-0002-1700-6842
  • Sales Maicas, Salvador|||0000-0001-9457-976X
[EN] Multicore optical fibers are of great interest in the optical sensing field. Their core diversity and spatial distribution enable the development of sensing mechanisms that are not possible in single-core fibers. In this paper, we study the use of the inter-core crosstalk phenomena for the implementation of a surrounding refractive index (SRI) sensor. The selective inscription of a tilted fiber Bragg grating (TFBG) intentionally increases the inter-core crosstalk between the inscribed cores and makes it sensitive to the SRI. With this technique we simplify the measurement of the SRI and improve the identification and tracking of the excited cladding modes, as compared with the analysis of the transmission spectrum of a TFBG in single-core fibers. The proposed device is also sensitive to temperature. Temperature is obtained from the crosstalk wavelength shift with a measured sensitivity of 9.75 pm/degrees C. The SRI is obtained from the measurement of the crosstalk optical power. For increasing SRIs the cladding modes gradually fade, reducing the crosstalk optical power. We observed that the higher the tilt, the higher the sensor sensitivity. For a 7 degrees TFBG the SRI sensitivity obtained is -74.2 dB/RIU from 1.31 to 1.39 and -250.8 dB/RIU from 1.39 to 1.44., This work was supported in part by the Spanish Ministry of Economy and Competitiveness under the DIMENSION TEC2017 88029-R Project and in part by the Generalitat Valenciana by PROMETEO 2017/103 research excellency award and IDI/FEDER/2018 GVA Infraestructura. The work of J. Madrigal was supported by Universitat Politecnica de Valencia scholarship PAID-01-18. The work of D. Barrera was supported by Spanish MICINN fellowship IJCI-2017-32476.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Regenerated Fiber Bragg Gratings in Multicore Fiber for Multi-parameter Sensing

  • Madrigal-Madrigal, Javier|||0000-0003-3156-1321
  • Barrera Vilar, David|||0000-0002-1700-6842
  • Sales Maicas, Salvador|||0000-0001-9457-976X
[EN] Multiple regenerated fiber Bragg gratings were inscribed in all the cores of a seven-core fiber in order to develop a multi-parameter sensor designed to operate at high temperatures. We experimentally showed the possibility of measuring strains of up to 1200 mu epsilon, curvatures from 0 degrees to 360 degrees and temperatures up to 1000 degrees C, with a maximum curvature magnitude of at least 4.6 m(-1) and a maximum sensibility of 96 pm/m(-1)., This work was supported in part by the Spanish Ministry of Economy and Competitiveness under the DIMENSION TEC2017 88029-R Project and in part by the Generalitat Valenciana by the PROMETEO 2017/103 Research Excellency Award and IDI/FEDER/2018 GVA Infraestructura. The work of J. Madrigal was supported by a Universitat Politecnica de Valencia scholarship PAID-01-18. The work of D. Barrera was supported by a Spanish MICINN Fellowship IJCI-2017-32476.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Opto-Mechanical Interactions in Multi-Core Optical Fibers and Their Applications

  • Diamandi, Hilel Hagai
  • London, Yosef
  • Bergman, Arik
  • Bashan, Gil
  • Zadok, Avi
  • Madrigal-Madrigal, Javier|||0000-0003-3156-1321
  • Barrera Vilar, David|||0000-0002-1700-6842
  • Sales Maicas, Salvador|||0000-0001-9457-976X
[EN] Optical fibers containing multiple cores are being developed towards capacity enhancement in space-division multiplexed optical communication networks. In many cases, the fibers are designed for negligible direct coupling of optical power among the cores. The cores remain, however, embedded in a single, mechanically-unified cladding. Elastic (or acoustic) modes supported by the fiber cladding geometry are in overlap with multiple cores. Acoustic waves may be stimulated by light in any core through electrostriction. Once excited, the acoustic waves may induce photo-elastic perturbations to optical waves in other cores as well. Such opto-mechanical coupling gives rise to inter-core cross-phase modulation effects, even when direct optical crosstalk is very weak. The cross-phase modulation spectrum reaches hundreds of megahertz frequencies. It may consist of discrete and narrow peaks, or may become quasi-continuous, depending on the geometric layout. The magnitude of the effect at the resonance frequencies is comparable with that of intra-core cross-phase modulation due to Kerr nonlinearity. Two potential applications are demonstrated: single-frequency opto-electronic oscillators that do not require radio-frequency electrical filters, and point-sensing of liquids outside the cladding of multi-core fibers, where light cannot reach., This work was supported in part by a Starter Grant from the European Research Council (ERC) under Grant H2020-ERC-2015-STG 679228 (L-SID), in part by the Israeli Ministry of Science and Technology under Grant 61047, and in part by the Spanish Ministry of Economy and Competitiveness under the DIMENSION TEC2017 88029-R Project. H. H. Diamandi was supported by the Azrieli Foundation for the award of an Azrieli Fellowship. The work of J. Madrigal was supported by Universitat Politecnica de Valencia scholarship PAID-01-18. The work of D. Barrera was supported by Spanish MICINN fellowship IJCI-2017-32476.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Multicore optical fiber shape sensors suitable for use under gamma radiation

  • Barrera Vilar, David|||0000-0002-1700-6842
  • Madrigal-Madrigal, Javier|||0000-0003-3156-1321
  • Sales Maicas, Salvador|||0000-0001-9457-976X
  • Delepine-Lesoille, Sylvie
[EN] We have designed and implemented a fiber optic shape sensor for high-energy ionizing environments based on multicore optical fibers. We inscribed two fiber Bragg gratings arrays in a seven-core optical fiber. One of the arrays has been inscribed in a hydrogen-loaded fiber and the other one in an unloaded fiber in order to have two samples with very different radiation sensitivity. The two samples were coiled in a metallic circular structure and were exposed to gamma radiation. We have analyzed the permanent radiation effects. The radiation-induced Bragg wavelength shift (RI-BWS) in the hydrogen-loaded fiber is near ten times higher than the one observed for the unloaded fiber, with a maximum wavelength shift of 415 pm. However, the use of the multiple cores permits to make these sensors immune to RI-BWS obtaining a similar curvature error in both samples of approximately 1 cm without modifying the composition of the fiber, pre-irradiation or thermal treatment., Ministerio de Economia y Competitividad (DIMENSION TEC2017 88029- R); Generalitat Valenciana (IDI/FEDER/2018, PROMETEO 2017/103); H2020 Marie Sklodowska-Curie Actions (MSCA-ITN-ETN-722509); Universitat Politecnica de Valencia (PAID-01-18); Ministerio de Ciencia, Innovacion y Universidades (IJCI-2017-32476).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

In Situ Raman Characterization of SOFC Materials in Operational Conditions: A Doped Ceria Study

  • Solís, Cecilia
  • Balaguer Ramirez, Maria|||0000-0002-7098-9235
  • Serra Alfaro, José Manuel|||0000-0002-1515-1106
[EN] The particular operational conditions of electrochemical cells make the simultaneous characterization of both structural and transport properties challenging. The rapidity and flexibility of the acquisition of Raman spectra places this technique as a good candidate to measure operating properties and changes. Raman spectroscopy has been applied to well-known lanthanide ceria materials and the structural dependence on the dopant has been extracted. The evolution of Pr-doped ceria with temperature has been recorded by means of a commercial cell showing a clear increment in oxygen vacancies concentration. To elucidate the changes undergone by the electrolyte or membrane material in cell operation, the detailed construction of a homemade Raman cell is reported. The cell can be electrified, sealed and different gases can be fed into the cell chambers, so that the material behavior in the reaction surface and species evolved can be tracked. The results show that the Raman technique is a feasible and rather simple experimental option for operating characterization of solid-state electrochemical cell materials, although the treatment of the extracted data is not straightforward., This research was funded by the Spanish Government (IJCI-2017-34110, RTI2018-102161 and SEV-2016-0683 grants).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Curvature, twist and pose measurements using fiber Bragg gratings in multi-core fiber: A comparative study between helical and straight core fibers

  • Khan, Fouzia
  • Misra, Sarthak
  • Barrera Vilar, David|||0000-0002-1700-6842
  • Sales Maicas, Salvador|||0000-0001-9457-976X
[EN] This paper presents a technique to acquire measurements of curvature, twist and pose for two multi-core fibers; one with straight cores and the other with helical cores. Both the fibers have multiple fiber Bragg grating (FBG) sensors inscribed in the cores and the fibers are placed in known configurations in order to compare their measurement accuracy. For the curvature measurements both the fibers are placed in constant curvature slots; for the twist measurements, a set of twists are applied to each fiber and for the pose measurements the fibers are placed in molds of different shape. The mean curvature errors are 0.22 and 0.13 m(-1), in the helical and straight core fiber respectively. For the twist measurement the mean errors are 26.57 degrees 1m and 146.50 degrees 1m in the helical and straight core fiber, respectively. Lastly, the pose measurement consists of position and orientation where the orientation is represented in the axis-angle form. The mean position errors are 0.49 and 0.27 mm, the mean axis orientation errors are 0.12 degrees and 0.26 degrees degrees and the mean angle orientation errors are 1.10 degrees and 1.18 degrees, for the helical and straight core fiber, respectively. The results show that the twist measurement error is significantly low with the helical core fiber, thus helical core fiber is better suited than straight core fiber for applications where twist measurements are required., This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement #688279 (EDEN2020). It was also partially supported by the Spanish Ministry of Economy and Competitiveness under the project DIMENSION TEC2017-88029-R. The work of D. Barrera was supported by Spanish MICINN fellowship IJCI-2017-32476. The funding sources were not involved in the research nor in the preparation of the article.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Few-mode fibre delay lines with inscribed long period gratings for radiofrequency signal processing

  • García-Cortijo, Sergi|||0000-0002-7237-9457
  • Madrigal-Madrigal, Javier|||0000-0003-3156-1321
  • Barrera Vilar, David|||0000-0002-1700-6842
  • Sales Maicas, Salvador|||0000-0001-9457-976X
  • Gasulla Mestre, Ivana|||0000-0001-8088-7796
  • Guillem-Cogollos, Rubén
[EN] We propose and experimentally demonstrate distributed radiofrequency signal on a few-mode-fibre device. The inscription of long period gratings at specific locations along the fibre allows the excitation of the higher-order modes while adjusting the modal group delays required for sample true time delay line operation., This research was supported by the ERC Consolidator Grant 724663, Universitat Politècnica de València PAID-01-18 scholarship for J. Madrigal and the Spanish MINECO through: TEC2016-80150-R Project, BES-2015-073359 scholarship for S. García, IJCI-2017-32476 fellowship for D. Barrera and RYC-2014-16247 fellowship for I. Gasulla. We thank Prysmian for providing the FMF and Cailabs for providing the mode multiplexers.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Sampled true time delay line operation by inscription of long period gratings in few-mode fibers

  • García-Cortijo, Sergi|||0000-0002-7237-9457
  • Madrigal-Madrigal, Javier|||0000-0003-3156-1321
  • Barrera Vilar, David|||0000-0002-1700-6842
  • Sales Maicas, Salvador|||0000-0001-9457-976X
  • Gasulla Mestre, Ivana|||0000-0001-8088-7796
  • Guillem-Cogollos, Rubén
[EN] We propose and experimentally demonstrate distributed microwave photonics signal processing over a few-mode fiber link by implementing 4-sample true time delay line operation. The inscription of a set of long period gratings at specific locations along the few-mode fiber allows the excitation of the higher-order modes while adjusting the individual sample group delays and amplitudes that are required for sampled true time delay line behavior. Since solely the injection of the fundamental mode at the few-mode fiber input is required, we render this signal processing system independent of any preceding fiber link that may be required in addition to distribute the signal. We experimentally validate the performance of the implemented true time delay line when applied to radiofrequency signal filtering., European Research Council (ERC) (Consolidator Grant 724663); Spanish MINECO (TEC2014-60378-C2-1-R and TEC2016-80150-R projects, BES-2015-073359 scholarship for S. Garcia, IJCI-2017-32476 fellowship for D. Barrera, Ramon y Cajal fellowship RYC-2014-16247 for I. Gasulla); Universitat Politecnica de Valencia (PAID-01-18 scholarship for J. Madrigal).