Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Optical and structural investigation of methylammonium lead perovskite mixed halide (I, Br, and Cl) on spin-coated zinc oxide

  • Klegayere Emmanuel, Kone
  • Marí Soucase, Bernabé
  • Soro, Donafologo
  • Bouich, Amal|||0000-0001-6745-8831
[EN] This study investigated the effect of mixing different halides bromine (Br) with iodine (I) and Br with chlorine (Cl) and using only bromide for methylammonium lead perovskites films deposited in ZnO to produce different heterojunctions ZnO/MAPbBr3, ZnO/MAPbBr2I and ZnO/MAPbBr2Cl. Thus, these three heterojunction samples were produced and characterized. The perovskite is deposited at ZnO films showed two main peaks located at 2¿ = 33.66° and 2¿ = 37.69°. These peaks correspond to the (0 0 2) and (1 0 1) planes of the hexagonal wurtzite structure of ZnO respectively. The XRD results indicate that all the heterojunction samples show two main peaks at 2¿ = 14.79° and 2¿ = 29.83° for the (1 0 0) and (2 0 0) crystallographic planes respectively. The peaks of the sample mixed with iodine are the most intense and those of the sample mixed with chlorine are the least intense. These results also reveal that the mixed samples have lower crystallinity than the unmixed ZnO/MAPbBr3 sample. The SEM results confirmed this. The UV¿Visible results indicate that the sample mixed with iodine absorbs the most and has the smallest band gap of 2.15 eV. The band gaps of the heterojunctions range from 2.15 eV to 2.4 eV. The unmixed sample (ZnO/MAPbBr3) has the largest band gap. The degradation study showed that the sample mixed with iodine degrades faster., Author Klegaye Emmanuel Kone thanks Erasmus + KA107 for the grant. Amal Bouich acknowledges Ministerio de Ciencia e Innovacion (Spain) for funding support through Margarita Salas Fellowship (MCIN/AEI/10.13039/501100011033). This work has been funded by the Conselleria d Innovacio, Universitats, Ciencia i Societat Digital (Generalitat valenciana, Prometeus 2023 CIPROM2022/03) and the Agencia Estatal de Investigacion (Spain) through project PID2019-107137RBC21/AEI/10.13039/501100011033 and by ERDF under the funding Away of making Europe .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Synthesis and characterization of kesterite Cu2ZnSn (SxSe1-x) 4 thin films with low-cost for efficient solar cells

  • Bouich, Amal|||0000-0001-6745-8831
  • Marí, B.|||0000-0003-0001-419X
[EN] In this study, we conducted an investigation on the Cu2ZnSnS4 (CZTS) k¿esterite compound, which is considered an attractive material for its favorable absorption properties, making it a suitable semiconductor for photovoltaic applications. However, its market potential is limited by its low efficiency of 12.6%, primarily caused by the presence of secondary phases that act as recombination centers. Theoretically, the efficiency limit for CZTS ranges from 31% to 33%. To enhance the photovoltaic performance of CZTS, we employed a doping strategy by incorporating selenium (Se) into the Cu2ZnSn(SxSe1-x)4 film, where the sulfur-to-selenium ratio (S/Se) was optimized within the range of 0< x <1. The CZTS films were deposited onto FTO substrates using the spray pyrolysis technique, which is a simple and cost-effective method. The characterization of these films involved X-ray diffraction (XRD) and UV¿visible spectroscopy analysis. Additionally, the morphology and topography of the CZTSSe layers were examined using scanning electron microscopy (SEM) and atomic force microscopy (AFM), respectively. Trans mission electron microscopy (TEM) was also employed. The results obtained in this study indicate that CZTSSe films exhibit band gap values ranging from 1.54 eV to 1.68 eV and grain compactness, with larger agglomerated grains on the film surface when the S/Se ratio is approximately 0.5 or lower. Moreover, the resistivity measurements revealed significant variations when sulfur and selenium were combined, suggesting the influence of their composition on the electrical properties of the CZTS films., Aka Hyacinthe AKA acknowledged Erasmus107 for the grant, The author Amal Bouich acknowledges MCIN for funding support through Margarita Salas Fellowship (MCIN/AEI/10.13039/501100011033). This work has been funded by the Ministerio de Ciencia e Innovacio¿n (Spain) and by the Spanish Agencia Estatal de Investigacio¿n through projects BESTMAT PID2019-107137RB-C21/AEI/10.13039/501100011033 and PID2019-107137RB-C22/AEI/10.13039/501100011033 and by ERDF under the funding A way of making Europe