Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Multiplexing THz Vortex Beams With a Single Diffractive 3-D Printed Lens

  • Machado-Olivares, Federico Jose
  • PRZEMYSLAW ZAGRAJEK
  • WALTER DANIEL FURLAN
  • Ferrando, Vicente|||0000-0002-7434-7109
  • Monsoriu Serra, Juan Antonio|||0000-0003-3350-7951
[EN] We present a novel method for experimentally generating multiplexed THz vortex beams by using a single three-dimensional printed element that combines a set of radially distributed spiral phase plates, and a binary focusing Fresnel lens. With this element, we have experimentally demonstrated that THz multiplexing can be tailored to fit within a small space on an optical bench. Results are presented beside numerical simulations, demonstrating the robust nature of the experimental method., This work was supported in part by the Ministerio de Economia y Competitividad, Spain, under Grant DPI2015-71256-R, in part by the Generalitat Valenciana, Spain, under Grant PROMETEO II-2014-072, and in part by the National Center for Research and Development in Poland under Grant LIDER/020/319/L-5/13/NCBR/2014.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Capítulo o parte de un libro (BookPart)

Microwave-assisted preparation of 1D NCs for photodegradation process of organic dyes

  • Zaba, A.
  • Matras-Postolek, Katarzyna
  • Sovinska, S.
  • Bogdal, D.
[EN] Zinc sulphide (ZnS) and zinc selenide (ZnSe) and manganese-doped and un-doped with different morphologies from 1D do 3D microflowers were successfully fabricated in only a few minutes by solvothermal reactions under microwave irradiation. In order to compare the effect of microwave heating on the properties of obtained nanocrystals, additionally the synthesis under conventional heating was conducted additionally in similar conditions. The obtained nanocrystals were systematically characterized in terms of structural and optical properties using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), diffuse reflectance UV-Vis spectroscopy (DR UV-Vis), Fourier-transform infrared spectroscopy (FT-IR), photoluminescence spectroscopy (PL), X-ray photoelectron spectroscopy (XPS) and Brunauer-Emmett-Teller (BET) surface area analysis. The photocatalytic activity of ZnSe, ZnS, ZnS:Mn and ZnSe:Mn nanocrystals with different morphologies was evaluated by the degradation of methyl orange (MO) and Rhodamine 6G (R6G), respectively. The results show that Mn doped NCs samples had higher coefficient of degradation of organic dyes under ultraviolet irradiation (UV)., This work was financially supported by the National Centre for Research and Development within the V edition of the LIDER program (project number LIDER/009/185/L5/13/NCBR/2014).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Polymorphisms in coding and non-coding regions of rabbit (Oryctolagus cuniculus) myogenin (MyoG) gene

  • Migdał, Łukasz
  • Pałka, Sylwia
[EN] In animal breeding, selection based on growth is very often used, as this trait affects the profitability of animal production. Identification of  polymorphisms within the genes affecting the growth process seems to be very important. Therefore, we decided to analyse rabbit myogenin (MyoG gene) for potential polymorphic sites and their association with growth and carcass traits in Termond White (TER), Belgian Giant Grey (BGG) and crossbred New Zealand White×Belgian Giant Grey (NZW×BGG) rabbits. We found three single nucleotide polymorphisms (SNPs) – in 5’ upstream sequence g.68679476 C>T, in exon 1 – silent mutation g.68680096 T>C and g.68680097 G>A resulting in change of GTG triplet (valine) into ATG triplet (methionine). Association analysis showed that GG genotype weaning weight was statistically higher compared to GA in TER population (P=0.005), and that the hind parts for GG genotypes were heavier compared to those of GA (P=0.024), but association analysis of dissectible parts showed this was caused by higher bone weight (P=0.015). For g.68679476 C>T in NZW×BGG population, the CC genotypes for fore (678±35) and hind part (615±29) weights were heavier compared to CT (588±16 and 549±13, respectively); moreover, association analysis of dissectible parts showed that weight of dissectible meat in hind part. Unfortunately, we did not find similar associations for other analysed breeds. For g.68679476 C>T in NZWxBGG musculus longissimus lumborum pH leg after 24 h chilling (pH24L) were statistically lower for CC genotypes compared to CT (P=0.027). For g.68680097 G>A in Termond White population L* value on the hind leg after 24 h chilling (L*24H) was higher for GA genotypes compared to GG (P=0.03), while for g.68679476 C>T for musculus longissimus lumborum L* value after 24 h (L*24L) CC genotypes had higher value compared to CT (P=0.016) in BGG population. Moreover, in BGG population CT genotypes had higher weaning weight compared to CC (P=0.018). Our results show that SNPs within the MyoG gene may influence growth traits in some rabbit breeds, but the evolutionary conserved sequence may not be favourable for changes within coding sequences. For a better understanding thereof, additional analysis is required., This research was financed by the National Centre for Research and Development (Poland) decision number LIDER/27/0104/L-9/17/NCBR/2018.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

3D printed diffractive terahertz lenses

  • Furlan, Walter D.
  • Zagrajek, Przemyslaw
  • Czerwinska, Elzbieta
  • Szustakowski, Mieczyslaw
  • Ferrando, Vicente|||0000-0002-7434-7109
  • Monsoriu Serra, Juan Antonio|||0000-0003-3350-7951
[EN] A 3D printer was used to realize custom-made diffractive THz lenses. After testing several materials, phase binary lenses with periodic and aperiodic radial profiles were designed and constructed in polyamide material to work at 0.625 THz. The nonconventional focusing properties of such lenses were assessed by computing and measuring their axial point spread function (PSF). Our results demonstrate that inexpensive 3D printed THz diffractive lenses can be reliably used in focusing and imaging THz systems. Diffractive THz lenses with unprecedented features, such as extended depth of focus or bifocalization, have been demonstrated., Ministerio de Economia y Competitividad (MINECO) (FIS2011-23175); Generalitat Valenciana (PROMETEOII/2014/072); National Center for Research and Development in Poland (LIDER/020/319/L-5/13/NCBR/2014).