Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 10
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Alumina reinforced eucryptite ceramics: Very low thermal expansion material with improved mechanical properties

  • García-Moreno, Olga
  • Bittmann, Birgit
  • Fernández-Valdés, Adolfo
  • Torrecillas San Millán, Ramón
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
[EN] Composite materials formed by a LAS matrix reinforced with second phases are promising materials in many applications where better mechanical properties than those corresponding to conventional low thermal expansion coefficient materials are required. In this study we will show the capability of the design of a LAS-alumina submicron composite. The main scope of this work is to test the sinterability of the composites and to design a composition for a very low thermal expansion submicron composite. For this purpose, Taimei alumina (TM-DAR) powders and an ad hoc synthesized beta-eucryptite phase were used to fabricate the composite. XRD phase compositions and microstructures are discussed together with data from dilatometries in a wide temperature range. The results obtained show the possibility of designing a submicron composite with a very low thermal expansion coefficient and improved mechanical properties that can be used in oxidizing conditions. (C) 2011 Elsevier Ltd. All rights reserved., We would like to thank Prof. Salvador de Aza and Prof. Serafin Moya for the thorough discussion of LAS-Al<INF>2</INF>O<INF>3</INF> solid state compatibility and comments on a first version of the manuscript. The authors greatly appreciate the support of the EU for the IP-Nanoker NMP3-CT-2005-515784 in the frame of the 6th Framework Program. Garcia-Moreno is working for CSIC under a JAE-Doc contract co-funded by the ESF. A. Borrell is working with financial support of National Plan Project MAT2006-01783 under FPI contract.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Surface coating on carbon nanofibers with alumina precursor by different synthesis routes

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Rocha, V. G.
  • Torrecillas, R.
  • Fernandez, A.
[EN] Alumina-reinforced carbon nanofiber nanocomposites were prepared using different routes; powders mixture, colloidal route and sol-gel process followed by spark plasma sintering (SPS). CNFs/xAl(2)O(3) (x = 10-50 vol.%) were prepared through nanopowders mixing in a high-energy attrition milling. The main limitations in the preparation of this kind of nanocomposites are related to the difficulty in obtaining materials with a homogeneous distribution of both phases and the different chemical nature of CNFs and Al(2)O(3), which causes poor interaction between them. A surface coating of CNFs by wet chemical routes with an alumina precursor is proposed as a very effective way to improve the interaction between CNFs and Al(2)O(3). An improvement of 50% in fracture strength was found for similar nanocomposite compositions when the surface coating was used. The improved mechanical properties of these nanocomposites are caused by stronger interaction between the CNFs and Al(2)O(3). Crown Copyright (C) 2010 Published by Elsevier Ltd. All rights reserved., This work has been carried out with financial support of National Plan Projects MAT2006-01783 and MAT2007-30989-E and the Regional Project FICYT PC07-021. A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for Ph.D. grant.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Carbon nanofiber- and alumina-reinforced lithium aluminosilicate for controlled thermal expansion materials

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Garcia-Moreno, Olga
  • Torrecillas, Ramón
  • Garcia-Rocha, Victoria
  • Fernandez, Adolfo
[EN] Materials with a very low or tailored thermal expansion have many applications ranging from cookware to the aerospace industry. Among others, lithium aluminosilicates (LAS) are the most studied family with low and negative thermal expansion coefficients. However, LAS materials are electrical insulators and have poor mechanical properties. Nanocomposites using LAS as a matrix are promising in many applications where special properties are achieved by the addition of one or two more phases. The main scope of this work is to study the sinterability of carbon nanofiber (CNFs)/LAS and CNFs/alumina/LAS nanocomposites, and to adjust the ratio among components for obtaining a near-zero or tailored thermal expansion. Spark plasma sintering of nanocomposites, consisting of commercial CNFs and alumina powders and an ad hoc synthesized beta-eucryptite phase, is proposed as a solution to improving mechanical and electrical properties compared with the LAS ceramics obtained under the same conditions. X-ray diffraction results on phase compositions and microstructure are discussed together with dilatometry data obtained in a wide temperature range (-150 to 450 degrees C). The use of a ceramic LAS phase makes it possible to design a nanocomposite with a very low or tailored thermal expansion coefficient and exceptional electrical and mechanical properties., This work was financially supported by the National Plan Projects MAT2006-01783 and MAT2007-30989-E and the Regional Project FICYT PC07-021. A Borrell thanks the Spanish Ministry of Science and Innovation for her research grant BES2007-15033. O Garcia-Moreno is working for CSIC under a JAE-Doc contract co-funded by the ESF.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Alumina-carbon nanofibers nanocomposites obtained by spark plasma sintering for proton exchange membrane fuel cell bipolar plates

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Torrecillas, Ramón
  • Rocha, Victoria G.
  • Fernández, Adolfo
[EN] There is an increasing demand of multifunctional materials for a wide variety of technological developments. Bipolar plates for proton exchange membrane fuel cells are an example of complex functionality components that must show among other properties high mechanical strength, electrical, and thermal conductivity. The present research explored the possibility of using alumina¿carbon nanofibers (CNFs) nanocomposites for this purpose. In this study, it was studied for the first time the whole range of powder compositions in this system. Homogeneous powders mixtures were prepared and subsequently sintered by spark plasma sintering. The materials obtained were thoroughly characterized and compared in terms of properties required to be used as bipolar plates. The control on material microstructure and composition allows designing materials where mechanical or electrical performances are enhanced. A 50/50¿vol.% alumina¿CNFs composite appears to be a very promising material for this kind of application., This work has been carried out with financial support of National Plan Projects MAT2006-01783 and MAT2007-30989-E and the Regional Project FICYT PC07-021. A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for Ph.D. grant.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Spark plasma sintering of TiyNb1-yCxN1-x monolithic ceramics obtained by mechanically induced self-sustaining reaction

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Garcia-Rocha, Victoria
  • Fernandez, Adolfo
  • Chicardi, Ernesto
  • Gotor, Francisco J.
Nanometer-sized titanium-niobium carbonitride powders (TiyNb1-yCxN1-x) with different Ti/Nb atomic ratios were obtained by a mechanically induced self-sustaining reaction, and sintered by spark plasma sintering technique at 1500 degrees C for 1 min in a vacuum atmosphere. Mechanical properties such as hardness and Young's modulus were determined by nanoindentation technique and friction and wear coefficients assessed by ball-on-disk testing using alumina ball in dry sliding conditions. The fracture surface and wear tracks of samples were examined by scanning electron microscopy. Results showed that it is possible to obtain dense monolithic ceramics from the solid solution (TiyNb1-yCxN1-x) with good mechanical properties and excellent wear resistance. The optimum values of nanomechanical properties were found for the Ti0.3Nb0.7C0.5N0.5 ceramic composition, which exhibited a high hardness over 26.0 GPa and Young's modulus around 400 GPa. Crown Copyright (C) 2012 Published by Elsevier B.V. All rights reserved., The authors would like to thank Dr. Emilio Rayon for performing the nanoindentation analysis in the Materials Technology institute (ITM) of the Polytechnic University of Valencia and to acknowledge the financial support received from Spanish Ministry of Science and Innovation for FPI grant (MAT2006-01783). This work was supported by the Spanish government under grant (MAT2010-17046), which is financed in part by the European Regional Development Fund of 2007-2013. E. Chicardi was supported by CSIC through a JAE-Pre grant, which is financed in part by the European Social Fund (ESF).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Microstructural design for mechanical and electrical properties of Spark Plasma Sintered Al2O3-SiC nanocomposites

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Alvarez, I.
  • Torrecillas, R.
  • Rocha, V. G.
  • Fernandez, A.
[EN] Al2O3-17 vol.% SiC nanocomposites were prepared by powder mixture of submicrosized alpha-Al2O3, nanosized gamma-Al2O3 and different nanosized beta-SiC. Materials were sintered by spark plasma sintering (SPS) technique at two temperatures (1400-1550 degrees C) and their electrical conductivity and mechanical properties were investigated. High-density composites have been achieved even at the lowest sintering temperatures and the microstructure characterization shows SiC particles located both within the Al2O3 matrix grains and/or at the Al2O3 grain boundaries. It has been demonstrated that microstructure tailoring is possible by suitable selection of starting materials and fast sintering by SPS. Accurate design of nanocomposites microstructures allows obtaining moderately conductive (<100 Omega cm) or insulating (10(8) Omega cm) materials while the chemical composition is similar. Crown Copyright (C) 2011 Published by Elsevier B.V. All rights reserved., Financial support of this work by the European Commission is gratefully acknowledged (IP Nanoker P3-CT-2005-515784). A. Borrell acknowledges the Spanish Ministry of Science and Innovation for Ph.D. grant (MAT2006-01783).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Sinterización por SPS de polvos ultrafinos de TiCxN1-x obtenidos mediante reacciones de autopropagación inducidas mecánicamente, Sintering by SPS of ultrafine TiCx N1-x powders obtained using mechanically induced self sustaining reaction

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Fernández, A.
  • Torrecillas, R.
  • Córdoba, J.M.
  • Avilés, M.A.
  • Gotor, F.J.
[EN] In this work high purity and nanometer character titanium carbonitride TiCx N1-x powders were obtained by mechanically induced self sustaining reaction (MSR) in a high-energy planetary ball mill, from a mixture of titanium with graphite or carbon nanofiber (CNFs) in a nitrogen atmosphere. A promising method for developing these materials is the coupling of the MSR with SPS sintering technique. The product is sintered at 1400 ºC and 1700 ºC, obtaining a completely dense monolithic ceramic (>99% t.d). In this work, the influence of SPS treatment and carbon precursor on material microstructures was studied and the main mechanical properties of the end material were evaluated, [ES] En el presente trabajo se han obtenido carbonitruros de titanio TiCx N1-x de alta pureza y con carácter nanométrico, por molienda reactiva (MSR) de alta energía en un molino planetario, a partir de la mezcla de titanio con grafito o nanofibras de carbono (CNFs) en una atmósfera de nitrógeno. Una metodología prometedora para el desarrollo de estos materiales consiste en el acoplamiento de la técnica MSR con el sinterizado por SPS. El producto obtenido se ha sinterizado a 1400 ºC y 1700 ºC, obteniéndose una cerámica monolítica totalmente densa (>99% d.t). En este trabajo se analizan las distintas microestructuras obtenidas en función del precursor de carbono y el tratamiento de SPS, evaluando las principales propiedades mecánicas de los materiales resultantes., Este trabajo ha sido llevado acabo con financiación procedente de los proyectos del plan nacional MAT2006-01783 y MAT2006-04911.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effect of CNFs content on the tribological behaviour of spark plasma sintering ceramic-CNFs composites

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Torrecillas, R.
  • Rocha, V. G.
  • Fernandez, A.
  • Bonache Bezares, Victoria
Alumina-carbon nanofibres (CNFs) and silicon carbide-CNFs nanocomposites with different volume fraction of CNFs (0-100vol.%) were obtained by spark plasma sintering. The effect of CNFs content on the tribological behaviour in dry sliding conditions on the ceramic-carbon nanocomposites has been investigated using the ball-on-disk technique against alumina balls. The wear rate of ceramic-CNFs nanocomposites decreases with CNFs increasing content. The friction coefficient of the Al 2O 3/CNFs and SiC/CNFs nanocomposites with high CNFs content was found to be significantly lower compared to monolithic Al 2O 3 and SiC due to the effect of CNFs and unexpectedly slightly lower than CNFs material. The main wear mechanism in the nanocomposite was abrasion of the ceramic and carbon components which act in the interface as a sort of lubricating media. The experimental results demonstrate that the addition of CNFs to the ceramic composites significantly reduces friction coefficient and wear rate, resulting in suitable materials for unlubricated tribological applications. © 2011., This work has been carried out with financial support of National Plan Projects MAT2006-01783 and MAT2007-30989-E and the Regional Project FICYT PC07-021. A. Borrell acknowledges the Spanish Ministry of Science and Innovation for her FPI Ph.D. grant. We would like to thank the people from Institute Technological of Materials (ITM) of the Polytechnic University of Valencia for helping us with the tribology experiments during A. Borrell's short stay in 2009.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Improvement of Carbon Nanofibers/ZrO2 Composites Properties with a Zirconia Nanocoating on Carbon Nanofibers by Sol–Gel Method

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Rocha, Victoria G.
  • Torrecillas, Ramon
  • Fernandez, Adolfo
The development of new carbon nanofibers (CNFs)–ceramic nanocomposite materials with excellent mechanical, thermal, and electrical properties is interesting for a wide range of industrial applications. Among the ceramic materials, zirconia stands out for their excellent mechanical properties. The main limitations in the preparation of this kind of nanocomposites are related with the difficulty in obtaining materials with homogeneous distribution of both phases and the dissimilar properties of CNFs and ZrO2 which causes poor interaction between them. CNFs-reinforced zirconia nanocomposites ZrO2/xCNFs (x=1–20 vol%) were prepared by powder mixture and sintered by spark plasma sintering (SPS). ZrO2-reinforced CNFs nanocomposites CNFs/xZrO2 (x=20 vol%) were prepared by powder mixture and a surface coating of CNFs by the wet chemical route with zirconia precursor is proposed as a very effective way to improve the interaction between CNFs and ZrO2. After SPS sintering, an improvement of 50% in fracture strength was found for similar nanocomposite compositions when the surface coating was used. The improved mechanical properties of these nanocomposites are caused by stronger interaction between the CNFs and ZrO2., This work was financially supported by National Plan Projects MAT2006-01783 and MAT2007-30989-E and the Regional Project FICYT PC07-021. A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for her research grant BES2007-15033.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Improvement of CNFs/SiC nanocomposites properties obtained from different routes and consolidated by pulsed electric-current pressure sintering

  • Rocha, Victoria G.
  • Torrecillas, Ramon
  • Fernandez, Adolfo
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
The influence of the preparation route and composition on carbon nanofibers-silicon carbide (CNFs/SiC) nanocomposites' properties was studied. Nanopowders were mixed by ultrasonic dispersion or high attrition milling and the consolidation was done by pulsed electric-current pressure sintering technique. The relative density and fracture strength of high-energy attrition milled CNFs/SiC nanocomposites gradually increased with the increase of sintering temperature, from 1400 to 1800 degrees C and holding time 1 to 30 min. A chemical surface coating of CNFs with alumina precursor is proposed as a very effective way for improving the interaction between CNFs and SiC. An increase of 54% in fracture strength was achieved on the nanocomposites when the surface coating was used. As a consequence of the stronger interaction between the components, which is achieved through the use of suitable processing route and sintering parameters, and the role of nano-alumina as sintering aid improved mechanical properties was achieved. (c) 2012 Elsevier B.V. All rights reserved., This work has been carried out with the financial support of the National Plan Projects nos. MAT2006-01783 and MAT2007-30989-E and the Regional Project no. FICYT PC07-021. A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for her Juan de la Cierva contract (no. JCI-2011-10498).