Skip to main content

COMPUESTOS CERAMICA-METAL Y ALEACIONES REFRACTARIAS DE W PARA SU APLICACION BAJO CONDICIONES DE SERVICIO SEVERAS: DISEÑO MICROESTRUCTURAL Y NUEVAS RUTAS DE PROCESAMIENTO

MAT2015-70780-C4-2-P

•
Funding agency name Ministerio de Economía y Competitividad
Funding agency acronym MINECO
Program Programa Estatal de Fomento de la Investigación Científica y Técnica de Excelencia
Subprogram Subprograma Estatal de Generación de Conocimiento
Call Proyectos de I+D (Excelencia / Generación de Conocimiento)
Call year 2015
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Management unit Secretaría de Estado de Educación, Formación Profesional y Universidades
Beneficiary centre UNIVERSIDAD CARLOS III DE MADRID

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Understanding of wetting and solubility behavior of Fe binder on Ti(C,N) cermets

  • Alvaredo Olmos, Paula
  • Dios Pérez, Miguel de
  • Ferrari, Begoña
  • Gordo Odériz, Elena
Given the great interest generated in the last years by the searching of new binders in hard materials, a work methodology has been created that allows the design of new metal – ceramic combinations. It includes the study of the solubility between the new binder and the reinforcement during the design of the binder composition combined with the knowledge of the sintering behavior of the cermet by monitoring the contact angle of the liquid phase formed at high temperature. Iron is considered as the main alternative binder in cermets; however, proper compositions are still under development as it is necessary to improve the sintering. This work propose the use of Ni as sintering aid to improve the wettability without the introduction of secondary phases. The article shows a comprehensive study of the high temperature behavior, in terms of solubility and wettability, of the system Fe-Ti(C,N) compared with the study of the conventional system Ni-Ti(C,N). Results show that the highest difference between Fe and Ni binders is the better wetting behavior of Ni binder, but the contact angle of liquid Fe is largely reduced by the addition of a small quantity of Ni. This fact opens the possibility to replace Ni as binder by a less toxic and cheaper binder., The authors would like to acknowledge thefinancial supportfrom the Spanish Government through the project MAT2015-70780-C4-2-P, MAT2015-70780-C4-1-P, and the Regional Govern-ment of Madrid through the program MULTIMAT-CHALLENGE, ref.S2013/MIT-2862, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Mechanical characterization of Ti(C,N)-based cermets fabricated through different colloidal processing routes

  • Dios Pérez, Miguel de
  • Kraleva, Irina
  • González Granados, Zoilo
  • Alvaredo Olmos, Paula
  • Ferrari, Begoña
  • Gordo Odériz, Elena
  • Bermejo, R.
In this work the influence of different colloidal processing routes on the mechanical behavior of several Ti(C,N)-based cermets has been studied. The materials were designed with a Ti(C,N) content ranging between 80 and 85 vol %, in a Fe-Ni alloy matrix (with and without carbon addition). Three processing techniques were investigated: (i) Slip Casting (SC), (ii) Slip Casting + Cold Isostatic Pressing (SC+CIP), and (iii) Spray-Dry + Uniaxial Pressing (SDP). Biaxial strength distributions were determined in all samples using the ball-on-three-balls (B3B) method on disc-shaped specimens. Results were interpreted in the framework of Weibull theory. The characteristic strength ranged between 1090 MPa and 1870 MPa. A fractographic analysis performed on selected specimens showed different critical flaws, depending on the processing route, related to the composition and porosity level in each case. Single Edge V-Notched Beam (SEVNB) specimens fabricated with SDP were tested under 4-point-bending, in order to identify the effect of Fe-Ni content and carbon addition on their fracture resistance. Detailed fractographic analyses revealed slightly different mechanisms of fracture associated with the Fe-Ni and carbon content. Fracture toughness values ranging between ∼12 and ∼14 MPa m were measured. Based upon these findings the SDP route is proposed to improve both the strength and toughness of Ti(C,N) cermets, which can be enhanced by the addition of carbon during the colloidal processing., The authors acknowledge thefinancial support from the Span-ish Government through the projects MAT2015-70780-C4-1-P and MAT2015-70780-C4-2-P, and the Regional Government of Madrid through the program MULTIMAT-CHALLENGE, ref. S2013/MIT-2862. M.Dios acknowledges MINECO through the grant BES-2013-065760, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Enhancing the Corrosion Protection of AA2024-T3 Alloy by Surface Treatments Based on Piperazine-Modified Hybrid Sol–Gel Films

  • Carbonell, Diógenes
  • Montoya, R.
  • Gelling, Victoria J.
  • Galván Sierra, Juan Carlos
  • Jiménez-Morales, Antonia
© 2020 by the authors., The aim of this study was to develop new chrome-free surface pretreatments for AA2024-T3 aluminum alloy. These pretreatments were based on hybrid organic–inorganic sol–gel thin films prepared from mixtures of γ-methacryloxypropyltrimethoxysilane (MAPTMS) and tetramethylorthosilicate (TMOS). Different MAPTMS/TMOS molar ratios were used for optimizing the physical–chemical characteristics of the sol–gel films. The formulation of a set of these sols was modified by incorporating piperazine (1,4-diazacyclohexane) as a corrosion inhibitor. The resulting sol–gel films were characterized by using Fourier transform infrared spectroscopy (FTIR), liquid-state 29Si nuclear magnetic resonance spectroscopy (29Si-NMR) and viscosity measurements. The corrosion performance of the sol–gel films was analyzed by using electrochemical impedance spectroscopy (EIS) and local electrochemical impedance mapping (LEIM). The characterization techniques indicated that piperazine behaved as a catalyst for the condensation reaction during the formation of the MAPTMS/TMOS organopolysiloxane network and produces an increase of the crosslinking degree of the sol–gel films. EIS and LEIM results showed that piperazine is an effective corrosion inhibitor, which can be used to enhance the active corrosion protection performance of sol–gel films., This research was funded by the Ministry of Economy and Competitiveness of Spain (MAT2015-65445-C2-1-R and MAT2015-70780-C4-2-P Projects), and the Regional Government of Madrid (Project P2018/NMT-4411 ADITIMAT-CM)., Peer reviewed