Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Ultra-fast direct growth of metallic micro- and nano-structures by focused ion beam irradiation

  • Córdoba, Rosa
  • Orús, Pablo
  • Strohauer, Stefan
  • Torres, T. E.
  • Teresa, José María de
An ultra-fast method to directly grow metallic micro- and nano-structures is introduced. It relies on a Focused Ion Beam (FIB) and a condensed layer of suitable precursor material formed on the substrate under cryogenic conditions. The technique implies cooling the substrate below the condensation temperature of the gaseous precursor material, subsequently irradiating with ions according to the wanted pattern, and posteriorly heating the substrate above the condensation temperature. Here, using W(CO)6 as the precursor material, a Ga+ FIB, and a substrate temperature of -100 °C, W-C metallic layers and nanowires with resolution down to 38 nm have been grown by Cryogenic Focused Ion Beam Induced Deposition (Cryo-FIBID). The most important advantages of Cryo-FIBID are the fast growth rate (about 600 times higher than conventional FIBID with the precursor material in gas phase) and the low ion irradiation dose required (∼50 μC/cm2), which gives rise to very low Ga concentrations in the grown material and in the substrate (≤0.2%). Electrical measurements indicate that W-C layers and nanowires grown by Cryo-FIBID exhibit metallic resistivity. These features pave the way for the use of Cryo-FIBID in various applications in micro- and nano-lithography such as circuit editing, photomask repair, hard masks, and the growth of nanowires and contacts. As a proof of concept, we show the use of Cryo-FIBID to grow metallic contacts on a Pt-C nanowire and investigate its transport properties. The contacts have been grown in less than one minute, which is considerably faster than the time needed to grow the same contacts with conventional FIBID, around 10 hours., Authors acknowledge financial support from the Spanish Ministry of Economy and Competitiveness (MINECO) through the projects MAT2017-82970-C1 and MAT2017-82970-C2, from CSIC through the project PIE201760E027 and from the Aragon Regional Government (Construyendo Europa desde Aragón) through projects E13_17R and LMP33_18, with European Social Fund funding. R. C. acknowledges Juan de la Cierva Incorporación 2014 program. S. S. acknowledges the support of an Erasmus+ scholarship to fund his stay at University of Zaragoza from J. W. Goethe-Universität, Frankfurt am Main, Germany., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Nanowire magnetic force sensors fabricated by focused-electron-beam-induced deposition

  • Mattiat, H.
  • Rossi, N.
  • Gross, B.
  • Pablo-Navarro, Javier
  • Magén, César
  • Badea, R.
  • Berezovsky, J.
  • Teresa, José María de
  • Poggio, M.
We demonstrate the use of individual magnetic nanowires (NWs), grown by focused-electron-beam-induced deposition (FEBID), as scanning magnetic force sensors. Measurements of their mechanical susceptibility, thermal motion, and magnetic response show that these NWs possess high-quality flexural mechanical modes and a strong remanent magnetization pointing along their long axis. Together, these properties make the NWs excellent sensors of weak magnetic field patterns, as confirmed by calibration measurements on a micron-sized current-carrying wire and magnetic scanning-probe images of a permalloy disk. The flexibility of FEBID in terms of the composition, geometry, and growth location of the resulting NWs, makes it ideal for fabricating scanning probes specifically designed for imaging subtle patterns of magnetization or current density., We acknowledge the support of the Kanton Aargau, the ERC through Starting Grant NWScan (Grant No. 334767), the SNF under Grant No. 200020-178863, the Swiss Nanoscience Institute, and the NCCR Quantum Science and Technology (QSIT) as well as from the Spanish Ministry of Economy and Competitiveness (MINECO) through the projects MAT2017-82970-C1 and MAT2017-82970-C2 and from the Aragon Regional Government (Construyendo Europa desde Aragón) through project E13_20R, with European Social Fund funding. J.P.-N.’s grant is funded by the Ayuda para Contratos Predoctorales para la Formación de Doctores, Convocatoria Res. 05/06/15 (BOE 12/06/15) of the Secretaría de Estado de Investigación, Desarrollo e Innovación in the Subprograma Estatal de Formación of the Spanish Ministry of Economy and Competitiveness with the participation of the European Social Fund., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Ultra-fast direct growth of metallic micro- and nano-structures by focused ion beam irradiation

  • Córdoba, Rosa
  • Orús, Pablo
  • Strohauer, Stefan
  • Torres, Teobaldo E.
  • De Teresa, José María
An ultra-fast method to directly grow metallic micro- and nano-structures is introduced. It relies on a Focused Ion Beam (FIB) and a condensed layer of suitable precursor material formed on the substrate under cryogenic conditions. The technique implies cooling the substrate below the condensation temperature of the gaseous precursor material, subsequently irradiating with ions according to the wanted pattern, and posteriorly heating the substrate above the condensation temperature. Here, using W(CO)6 as the precursor material, a Ga+ FIB, and a substrate temperature of -100 °C, W-C metallic layers and nanowires with resolution down to 38 nm have been grown by Cryogenic Focused Ion Beam Induced Deposition (Cryo-FIBID). The most important advantages of Cryo-FIBID are the fast growth rate (about 600 times higher than conventional FIBID with the precursor material in gas phase) and the low ion irradiation dose required (~50 µC/cm2), which gives rise to very low Ga concentrations in the grown material and in the substrate (=0.2%). Electrical measurements indicate that W-C layers and nanowires grown by Cryo-FIBID exhibit metallic resistivity. These features pave the way for the use of Cryo-FIBID in various applications in micro- and nano-lithography such as circuit editing, photomask repair, hard masks, and the growth of nanowires and contacts. As a proof of concept, we show the use of Cryo-FIBID to grow metallic contacts on a Pt-C nanowire and investigate its transport properties. The contacts have been grown in less than one minute, which is considerably faster than the time needed to grow the same contacts with conventional FIBID, around 10 hours.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Nanowire Magnetic Force Sensors Fabricated by Focused-Electron-Beam-Induced Deposition

  • Mattiat, H.
  • Rossi, N.
  • Gross, B.
  • Pablo-Navarro, J.
  • Magén, C.
  • Badea, R.
  • Berezovsky, J.
  • De Teresa, J.M.
  • Poggio, M.
We demonstrate the use of individual magnetic nanowires (NWs), grown by focused-electron-beam-induced deposition (FEBID), as scanning magnetic force sensors. Measurements of their mechanical susceptibility, thermal motion, and magnetic response show that these NWs possess high-quality flexural mechanical modes and a strong remanent magnetization pointing along their long axis. Together, these properties make the NWs excellent sensors of weak magnetic field patterns, as confirmed by calibration measurements on a micron-sized current-carrying wire and magnetic scanning-probe images of a permalloy disk. The flexibility of FEBID in terms of the composition, geometry, and growth location of the resulting NWs, makes it ideal for fabricating scanning probes specifically designed for imaging subtle patterns of magnetization or current density.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Vanadium trapped by oblique nano-sheets to preserve the anisotropy in Co–V thin films at high temperature

  • Favieres, C.
  • Vergara, J.
  • Magén, C.
  • Ibarra, M.R.
  • Madurga, V.
In this study, oriented nano-sheets generated during the growth of cobalt-rich Co–V and Co–Zn thin films induced a large anisotropy in the magnetic and transport properties. The regular nano-sheets were tilted 52–54 deg. with respect to the substrate plane, ˜ 3.0–4.0 nm thick, ˜ 30–100 nm wide, and ˜ 200–300 nm long, with an inter-sheet distance of ˜ 0.9–1.2 nm. In spite of the different microstructures of the two kinds of samples where the Co–V films were amorphous, whereas the Co–Zn films showed a growth of Zn nanocrystals, the oblique nano-sheet morphology conferred noticeable shape anisotropy to both specimens. This anisotropy resulted in an in-plane uniaxial magnetic anisotropy. The changes in the nano-morphology caused by thermal treatments, and hence in their anisotropic properties, were studied. While the Co–V samples retained or increased their magnetic and transport anisotropies, this anisotropic behavior vanished for the annealed Co–Zn films. High resolution transmission electron microscopy, HRTEM, including chemical analysis at the nano-scale, and the dependence of the anisotropic resistance on temperature allowed to establish the nature and the activation energy spectra of the atomic relaxation processes during heating. These processes displayed a single peak at 1.63 eV for the Co–V and two peaks at 1.67 and 2.0 eV for the Co–Zn. These spectra and their singularities were associated to the changes induced in the nano-morphology of the films by thermal treatments. The Co–V films retained their nano-sheet morphology almost up to 500 ºC; the Co–Zn films lost their nano-sheets at 290 ºC. The thermal stability exhibited by the Co–V films makes them useful for applications in ultra high frequency, optical, magnetostrictive and magneto-electric devices.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Generation of highly anisotropic physical properties in ferromagnetic thin films controlled by their differently oriented nano-sheets

  • Favieres, C.
  • Vergara, J.
  • Magén, C.
  • Ibarra, M. R.
  • Madurga, V.
We fabricated ferromagnetic nano-crystalline thin films of Co, Fe, Co–Fe and Co-rich and Fe-rich, Co–MT and Fe–MT (MT = transition metal), constituted by nano-sheets with a controlled slant. Visualization of these nano-sheets by Scanning Tunneling Microscopy and High-Resolution Transmission Electron Microscopy (HRTEM) showed typically tilt angles ≈56° with respect to the substrate plane, and nano-sheets ≈3.0–4.0 nm thick, ≈30–100 nm wide, and ≈200–300 nm long, with an inter-sheet distance of ≈0.9–1.2 nm, depending on their constitutive elements. Induced by this nano-morphology, these films exhibited large uniaxial magnetic anisotropy in the plane, the easy direction of magnetization being parallel to the longitudinal direction of the nano-sheets. In the as-grown films, typical values of the anisotropy field were between Hk ≈ 48 and 110 kA/m depending on composition. The changes in the nano-morphology caused by thermal treatments, and hence in the anisotropic properties, were also visualized by HRTEM, including chemical analysis at the nano-scale. Some films retained their nano-sheet morphology and increased their anisotropies by up to three times after being heated to at least 500 °C: for example, the thermal treatments produced crystallization processes and the growth of CoV and CoFe magnetic phases, maintaining the nano-sheet morphology. In contrast, other annealed films, Co, Fe, CoZn, CoCu… lost their nano-sheet morphology and hence their anisotropies. This work opens a path of study for these new magnetically anisotropic materials, particularly with respect to the nano-morphological and structural changes related to the increase in magnetic anisotropy.