Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 24
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Assessment of microplastics accumulation and aging in horizontal subsurface flow constructed wetlands

  • Echeverría-Puertas, Julie|||0000-0003-4139-0394
  • Martín Monerris, Miguel|||0000-0001-7464-9505
  • Asensi Dasí, Enrique Javier|||0000-0001-7935-3666
  • Hernández Crespo, Carmen|||0000-0002-6727-0481
  • Oliver Rajadel, Nuria
  • Rousseau, Diederik P.L.
[EN] Microplastics (MPs) are emerging pollutants whose fate after removal from wastewater remains uncertain. Constructed wetlands (CWs), as nature-based solutions with high retention of MPs, provide a suitable context to assess MP fate through extended interactions with sediments, vegetation, and microbial communities. This study evaluated MP distribution and aging in two sequential horizontal subsurface flow CWs (secondary wastewater treatment CW1 and sludge treatment CW2) in a residential area (Spain), in operation since 2014. Fibers were identified as the predominant type across depth profiles, with polymer-type abundance linked to urban wastewater inflows. Vertical patterns revealed denser polymers and smaller MPs accumulating in deeper layers, while lighter or later-introduced particles remained near the surface. MP distribution varied with treatment configuration, showing peak concentrations either in the top 5 cm at the CW1 inlet zone (566 MP/g) or in the deepest layer at the CW2 (464 MP/g). An exploratory phenomenological MP balance model reproduced the observed 97% removal efficiency by accounting for substrate retention and estimating accumulation and loss terms. A significant decrease in MP abundance from the inlet to the center confirmed efficient retention, with vegetation roots exhibiting MP levels equivalent to ~34%¿150% of the local substrate concentrations. Evidence of physical deterioration and spectra-detected chemical alterations (oxidation, hydrolysis) reflects long-term environmental aging and suggests potential pathways for polymer degradation. These findings support the hypothesis that CW conditions may favor MP aging, consistent with studies reporting microbiota-driven polymer degradation in similar natural environments. Further research should employ complementary techniques to confirm polymer aging mechanisms and optimize microbiota-based CWs to enhance MP removal., This research was supported by Catedra Aguas de Valencia and the Programa de Ayudas de Investigación y Desarrollo (PAID-01-24) of the Universitat Politecnica de Valencia, as well as the I+D+i project TED2021-130567B-I00 (RAINWETPIPA), funded by MICIU/AEI/10.13039/501100011033 and the European Union NextGenerationEU/ PRTR.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Off-Design Operation of a Carbon Capture Enabler Oxy-Fuel Combustion Engine with O2 Self-Production

  • Diego
  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Serrano, J.R.|||0000-0003-0692-3917
  • Gutierrez-Castro, Fabio Alberto
[EN] This work examines the behaviour of a spark-ignition engine using oxy-fuel combustion, coupled with an oxygen production cycle based on a mixed ionic-electronic ceramic membrane. Through 1D-0D simulations, two compression ratios are studied: the original ratio of 9.6 and the optimised CR of 20, under various load levels and altitude conditions. The results show that operational limits exist at part-load conditions, where reducing the load without implementing additional control strategies may compromise system performance. It is observed that at low loads, the intake pressure can fall below atmospheric pressure, encouraging the presence of N2 in the combustion process. Additionally, the engine can operate efficiently up to an altitude of 4000 m, although increasing boosting is required to maintain proper membrane conditions. These findings emphasise the importance of load control and the potential need for energy assistance under certain circumstances., This work has been partially supported by Grant PID2021-123351OB-I00 funded by MCIN/AEI/10.13039/501100011033 and by ERDF/EU. This research has been partially supported by Grant CIPROM/2021/061 funded by Generalitat Valenciana. Diego Contreras has been funded by the Universitat Politècnica de València s Research and Development Support Programme (PAID-01-24).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Micro-Multiband Imaging (µMBI) in the Technical Study and Condition Assessment of Paintings: An Insight into Its Potential and Limitations

  • Herrero-Cortell, Miguel Ángel|||0000-0002-3855-9542
  • Samaniego-Jiménez, Irene
  • Candelaria
  • Osete Cortina, Laura|||0000-0003-0709-5885
  • Abbafati, Arianna
  • Fuster-López, Laura|||0000-0001-7072-7190
  • Raïch-Creus, Marta
  • Vila-Espuña, Anna
  • Picollo, Marcello
[EN] Multiband imaging (MBI) is a non-invasive, portable digital technique that has become increasingly widespread in the technical study and condition assessment of paintings, owing to its affordability and ease of use. This paper presents an experimental study aimed at optimising MBI at the microscopic scale¿referred to as micro-multiband imaging (µMBI)¿with the particular aim of expanding its diagnostic capabilities. A range of µMBI techniques was used on custom-made mock-ups made up of pigments selected for their spectral responses, and representative of traditional artistic materials. The techniques used included microphotography of polarised and unpolarised visible light (µVIS), raking light microphotography (µRL), transmitted light microphotography (µTL), ultraviolet-induced visible luminescence microphotography (µUVL), near-infrared microphotography (µIR), near-infrared micro-trans-irradiation (µIRT), and near-infrared false-colour microphotography (µIRFC). The results obtained through µMBI were compared with those from standard MBI methods, allowing for a critical discussion of the strengths and limitations of this emerging approach. Results evidence that µMBI provides high-resolution, spatially specific insights into materials and painting techniques, offering a more detailed understanding at the microscale of how a painting was executed. It also enables the assessment of deterioration processes (e.g., cracking, delamination, and metal soap formation), contributing to a deeper comprehension of the origin and progression of failure phenomena and supporting the development of more informed, preventive conservation strategies., This research was carried out within the framework of the CIPROM/2023/9 Project (Programa Prometeo 2024, Conselleria de Educación, Cultura, Universidades y Empleo, Generalitat Valenciana) and Grant PID2023-148300NB-I00 funded by MICIU/AEI/10.13039/501100011033 and by ERDF/EU . The authors acknowledge Golden Artist Colours, Inc. for supplying paint samples for the preparation of the mock-ups. Finally, the authors acknowledge the predoctoral grant PID2023-148300NB-I00 funded by MICIU/AEI/10.13039/501100011033 and FSE+, as well as the predoctoral grant awarded under the Research and Development Support Program (PAID-01-24) of the Universitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Volatile Fingerprinting Empowers Salinity Monitoring in Peppermint Using MOS Sensors and Feature-Optimized Machine Learning

  • Ahmad, Ali|||0000-0001-5530-7374
  • Silva-Alvarado, Vinie Lee|||0009-0000-5857-3248
  • Sendra, Sandra|||0000-0001-9556-9088
  • Lloret, Jaime|||0000-0002-0862-0533
  • Heydari, Arman
[EN] Early detection of salinity stress is essential for precision agriculture, particularly in scalable, resource-constrained monitoring systems. This study presents a portable sensing module integrating a low-cost metal oxide semiconductor (MOS) sensor array with potential application for edge deployment to detect salinity stress in peppermint. Salinity significantly reduced plant biomass, confirming physiological stress induction. Volatile organic compound (VOC) fingerprints were collected over eleven consecutive days in a controlled enclosure. Sensor signals underwent outlier filtering, normalization, and smoothing, while treatment discrimination was verified using the Kruskal¿Wallis test. Thirty-three machine learning models were evaluated using a 75:25 train¿test split with five-fold cross-validation. Wide neural network models achieved the highest predictive performance, exceeding 98% test accuracy and a 97% macro F1 score. Feature adequacy analysis showed that six sensors captured the dominant variance required for reliable classification. Considering computational constraints, a bilayered neural network using only six features maintained over 97% accuracy with a memory footprint of 0.008 MB while remaining Pareto optimal. These findings support the feasibility of a compact, computationally efficient, and edge-compatible VOC sensing framework for salinity stress detection in precision agriculture and intelligent crop monitoring., Part of this work was funded by the Grant PRE2021-100809 funded by Agencia Estatal de Investigación (AEI) MICIU/AEI/10.13039/501100011033, by European Social Fund Plus (ESF+); by Universitat Politècnica de València through the Programa de Ayudas de Investigación y Desarrollo (PAID-01-24) ; and by Universidad Nacional José Faustino Sánchez Carrión through the Concurso de Proyectos de Investigación para Docentes Año 2026 ratified by RCU-0969-2026-CU-UNJFSC. This work has also received funding from the PRIMA Programme supported by the European Union, project PAVER, and it is supported by MCIN/AEI/10.13039/501100011033. Funders had no role in the design and execution of the study.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Carbon footprint assessment and sensitivity analysis of diagnostic colonoscopy

  • García-Castellanos, Marina|||0009-0009-6942-2299
  • Vilariño-Feltrer, Guillermo|||0000-0002-3063-3808
  • Tort-Ausina, Isabel|||0000-0002-1900-914X
  • Vidaurre, Ana|||0000-0003-3394-1176
  • Martín-Cabezuelo, Rubén|||0000-0002-5642-4692
  • Campillo-Fernández, Alberto J.|||0000-0002-2978-5994
  • Lorenzo-Zuñiga, Vicente
  • Pons-Beltrán, Vicente
  • Pohl, Heiko
[EN] This study performed a multifactorial carbon footprint assessment and sensitivity analysis of colonoscopy.This was a 1-week, single-center, prospective study including all outpatient diagnostic colonoscopies (n = 66). A cradle-to-grave life-cycle assessment methodology evaluated all essential supplies (accessories #1-15), endoscopic procedure (energy consumption, carbon dioxide [CO2] insufflation, bowel preparation, sedation), staff and patient transport, and waste management. The impact assessment was based on sensitivity analysis in different scenarios (base, best, worst) to calculate the Global Warming Potential over 100 years (GWP-100 measured in kg of CO2 equivalent [kgCO2e]).GWP-100 of a single colonoscopy was estimated to be 18.09 kgCO2e in the base scenario, with patient (8.61 kgCO2e) and staff (5.09 kgCO2e) transport, colonoscope manufacture and reprocessing (2.1 kgCO2e), and supplies (1.91 kgCO2e) contributing 47.6%, 28.1%, 11.7%, and 10.6%, respectively. Nitrile gloves, underpads, and a disposable peripheral oxygen saturation sensor accounted for nearly 50% of the total carbon footprint of all supplies. Patient preparation (bowel preparation, sedation, and CO2 insufflation) and energy consumption contributed only 2.0%. Staff and patient travel showed significant variations among worst, base, and best scenarios, with 18.8, 13.7, and 10.2 kgCO2e, respectively. The use of different amounts of medical supplies raised the carbon footprint to 2.38 kgCO2e in the worst scenario or diminished it to 1.56 kgCO2e in the best case.This analysis and multifactorial colonoscopy procedure assessment confirmed patient and staff transport as the main carbon footprint contributors. More sustainable and smarter transport could considerably lower the environmental impact of colonoscopy., European Society of Gastrointestinal Endoscopy http://dx.doi.org/10.13039/501100011927 ESGE Grant 2023 UPV-LaFe INBIO innovation projects PI2020-6 UCV-La Fe AP2023-06 Sociedad Española de Endoscopia Digestiva (SEED) FSEED Grant 2022 Instituto de Salud Carlos III http://dx.doi.org/10.13039/501100004587PI21/00193
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Proposal for Computationally Efficient Fog Computing System for Coffee Berry Borer Detection via Optimized YOLOv26

  • Huaman-Pacco, Ingrid P.
  • Sacoto-Cabrera, Erwin J.
  • Moreno-Cardenas, Edison
  • Silva-Alvarado, Vinie Lee|||0009-0000-5857-3248
  • Ahmad, Ali|||0000-0001-5530-7374
  • Sendra, Sandra|||0000-0001-9556-9088
  • Lloret, Jaime|||0000-0002-0862-0533
[EN] Highlights This research develops a computationally efficient system for real-time pest monitoring in complex agricultural environments. The key findings are: What are the main findings? FasterNet and SimSPPF reduced model parameters while enhancing mAP@0.5. Pareto analysis identified the optimal balance between detection accuracy and computational overhead. What are the implications of the main findings? Proposal for a structured optimization allows high-fidelity pest monitoring on low-power for fog devices. Structural efficiency can be prioritized without sacrificing detection reliability.Highlights This research develops a computationally efficient system for real-time pest monitoring in complex agricultural environments. The key findings are: What are the main findings? FasterNet and SimSPPF reduced model parameters while enhancing mAP@0.5. Pareto analysis identified the optimal balance between detection accuracy and computational overhead. What are the implications of the main findings? Proposal for a structured optimization allows high-fidelity pest monitoring on low-power for fog devices. Structural efficiency can be prioritized without sacrificing detection reliability.Highlights This research develops a computationally efficient system for real-time pest monitoring in complex agricultural environments. The key findings are: What are the main findings? FasterNet and SimSPPF reduced model parameters while enhancing mAP@0.5. Pareto analysis identified the optimal balance between detection accuracy and computational overhead. What are the implications of the main findings? Proposal for a structured optimization allows high-fidelity pest monitoring on low-power for fog devices. Structural efficiency can be prioritized without sacrificing detection reliability.Abstract The Coffee Berry Borer is the most destructive pest affecting global production of Coffea arabica. Early detection of pest-induced fruit damage remains challenging due to the small size of infestation symptoms and the dense clustering of coffee berries under complex field conditions. This study evaluates optimized object detection architectures designed to improve the balance between detection accuracy and computational efficiency. Three baselines were established: YOLOv8n (M0), YOLOv11n (M1), and YOLOv26n (M2). Seven architectural variants (M3-M9) were then developed by integrating FasterNet, SimSPPF, and EMA. Experimental results showed that M0 achieved the highest detection accuracy (mAP@0.5 = 0.9534 and 6.09 GFLOPs), whereas model M6, combining FasterNet and SimSPPF, provided the best accuracy-efficiency trade off with mAP@0.5 = 0.9446 and 5.12 GFLOPs. Pareto analysis confirmed M6 as the optimal configuration. Finally, in situ validation across 25 points achieved a mean F1-score of 0.7255 (SD = 0.0504) for infected berries despite cast shadows, proving its readiness for real-time agricultural deployment., This work was supported in part by the National University of Saint Anthony the Abbot in Cuzco, through the projects of the Professional School of Electronic Engineering; the Politecnica Salesiana University under the Fog Computing Simulation project. Financial support was also provided by the Grant PRE2021-100809 funded by Agencia Estatal de Investigacion (AEI) MICIU/AEI/10.13039/501100011033, by European Social Fund Plus (ESF+), and by Universitat Politecnica de Valencia through the "Programa de Ayudas de Investigacion y Desarrollo (PAID-01-24)". This work was further supported by the PRIMA Programme supported by the European Union, project PAVER, and it is supported by MCIN/AEI/10.13039/501100011033. Funders had no role in the design and execution of the study.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development and Characterization of Ductile Polylactic Acid Blends with Plasticized Zein for Injection Molding Applications

  • Lázaro-Hernández, C.|||0009-0002-8250-9363
  • Mario Nicolás
  • Vicente-Vinas, Maria del Puig|||0009-0005-0024-1503
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
[EN] This study explores the development of polylactic acid (PLA) blends incorporating plasticized zein, a corn-derived protein, and dipropylene glycol (DPG) as a biobased plasticizer to enhance compatibility and processability. Blends were produced via twin-screw extrusion and injection molding, with plasticized zein content ranging from 10 to 50 wt%. Mechanical testing showed a significant increase in ductility, with elongation at break rising from 6.3% (neat PLA) to 56.3% (50 wt% zein), accompanied by reduced tensile strength (58.4 MPa to 22.7 MPa) and impact resistance (42.2 kJ/m2 to 11.5 kJ/m2), due to phase separation and limited compatibility. Shore D hardness slightly declined (from 82.9 to 77.4). Thermal analysis revealed the Tg decreasing from 59.5 °C to 39.9 °C as zein content increased. Thermogravimetric analysis showed reduced thermal stability with zein addition, dropping the initial degradation temperature from 360.0 °C to 188.2 °C. Morphological analysis indicated greater heterogeneity at higher zein levels due to partial miscibility. Colorimetric data showed visible changes, and FTIR spectra confirmed physical interactions and partial miscibility between PLA and zein., This research is a part of the grant PID2023-152869OB-C22, and the grant TED2021-131762 A-I00, funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU /PRTR. The authors also thank Generalitat Valenciana - GVA, grant number CIGE/2023/46 and CIAICO/2023/253, for supporting this work. C. Lazaro-Hdez thanks Generalitat Valenciana - GVA for funding a predoc position through the CIACIF program co-funded by ESF Investing in your future, grant number CIACIF/2023/244. M. Miranda-Pinzon thanks Vice-rectorate for Research of the Universitat Politècnica de València (UPV) for funding a predoctoral contract in the PAID-01-24 program. J. IvorraMartinez thanks Generalitat Valenciana - GVA for funding a postdoc position through the CIAPOS program co-funded by ESF Investing in your future, grant number CIAPOS/2023/362. Microscopy services at UPV are also acknowledged for their help in collecting and analyzing FESEM images. Funding for open access charge: CRUE-Universitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Selective lignin conversion via flow photocatalysis for vanillin and bioplasticizers production

  • Marset, Xavier
  • Montilla-Verdú, Salvador
  • Pastor, Francisco J.
  • Rico, Elio
  • Bertella, Stefania
  • Ortuño, Manuel A.
  • Aschauer, Ulrich
  • Guijarro, Néstor
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Mario Nicolás
  • Lázaro-Hernández, C.|||0009-0002-8250-9363
  • Balart, Rafael|||0000-0001-5670-7126
[EN] Lignin valorization remains a roadblock in the development of green biorefineries. Currently, depolymerization strategies predominantly depend on energy- and resource-intensive thermochemical methods, while potential applications of the resulting bio-based products are often overlooked. Here, we show a scalable photocatalytic flow reactor for lignin deconstruction that operates at ambient conditions, along with a downstream process that yields commercially viable products at gram scale. An anthraquinone-based photocatalytic platform, when packed in a flow bed reactor, is demonstrated to selectively and nearly quantitatively cleave lignin¿s ß-O-4 moieties, achieving a benchmark yield of 7.1¿wt% for vanillin. The utilization of residual oligomers as plasticizers for biobased polylactic acid resulted in improved mechanical properties and shape memory effects, while maintaining its suitability for conventional 3D printing. This aldehyde-oriented platform represents a key advancement that complements existing ketone-oriented photocatalytic approaches targeting valuable chemicals from lignin conversion, and it ultimately contributes to the holistic utilization of lignin., This research is a part of the grant PID2023-152869OB-C22, and the grant TED2021-131762A-I00, funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU /PRTR. The authors also thank Generalitat Valenciana - GVA, grant number CIGE/2023/46 and CIAICO/2023/253, for supporting this work. J. G.-C. wants to thank FPU20/01732 grant funded by MCIN/AEI/10.13039/501100011033 and by ESF Investing in your future. M.M.-P. thanks Vice-rectorate for Research of the Universitat Politècnica de València (UPV) for funding a predoctoral contract in the PAID-01-24 program. M.A.O. thanks the Ramon y Cajal Program (RYC2022-035453-I) funded by MICIU/AEI/10.13039/501100011033 and FSE + . C.L.-H. wants to thank CIACIF/2023/244 grant funded by Generalitat Valenciana GVA. U.A thanks the supercomputer resources provided by the Vienna Scientific Cluster (VSC). N.G. thanks the Ramon y Cajal Program (RYC2018-023888-I) funded by MCIN/AEI/ 10.13039/501100011033. The authors also thank the support of the Generalitat Valenciana/FEDER (Spain) through the project IDIFEDER/2020/002. This research is also part of the project PID2021-128805NA-I00 funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU /PRTR. This project has received funding from the European Research Council (ERC) under the European Union s Horizon 2020 research and innovation programme (grant agreement no. 948829).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effects of Thermal Annealing on the Structure Properties Relationship of Plasticized Polylactic Acid with Citrates

  • Lázaro-Hernández, C.|||0009-0002-8250-9363
  • Mario Nicolás
  • Balart, Rafael|||0000-0001-5670-7126
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
[EN] This study investigates the effect of annealing on neat polylactic acid (PLA) and PLA plasticized with 20 wt% triethyl citrate (TEC) and acetyl tributyl citrate (ATBC), processed by twin-screw extrusion followed by injection molding. Two annealing treatments were applied at a lower temperature (T1-located at 10% above the onset of cold crystallization) and a higher temperature (T2- located at 10% below the endset of cold crystallization). The employed temperatures were provided by a calorimetric pre-study to assess the crystallization behavior. Mechanical characterization showed that annealing increased stiffness and brittleness, as indicated by a reduction in elongation at break from 276.7% (T0-without annealing treatment) to 53.7% (T2) for plasticized PLA with 20 wt% TEC, and an increase in tensile strength from 17.3 MPa (T0) to 25.1 MPa (T2). Charpy impact testing revealed higher energy absorption in T1, while surface hardness improved after annealing, with Shore D values for PLA increasing from 78.2 (T0) to 82.0 (T1). Thermal analysis demonstrated that annealing suppressed cold crystallization and substantially increased crystallinity, in PLA plasticized with 20 wt% ATBC rising from 34.1% (T0) to 65.3% (T2), without significantly affecting thermal stability. Plasticization reduced the glass transition temperature, although annealing partially restored rigidity. X-ray diffraction confirmed the higher crystalline order, and colorimetric evaluation showed perceptible changes in brightness and tone. Scanning electron microscopy revealed rougher fracture surfaces in annealed samples, which suggests a possible relationship with greater degree of crystallinity. Gel permeation chromatography indicated slight molecular weight degradation in neat PLA, whereas plasticized formulations remained stable., This research is a part of the grant PID2023-152869OBC22, and the grant TED2021-131762 A-I00, funded by MCIN/AEI/ https://doi.org/10.13039/501100011033 and by the European Union NextGenerationEU /PRTR. The authors also thank Generalitat Valenciana - GVA, grant number CIGE/2023/46 and CIAICO/2023/253, for supporting this work. C. Lazaro-Hdez thanks Generalitat Valenciana - GVA for funding a predoc position through the CIACIF program co-funded by ESF Investing in your future, grant number CIACIF/2023/244. M. Miranda-Pinzon thanks Vice-rectorate for Research of the Universitat Politècnica de València (UPV) for funding a predoctoral contract in the PAID-01-24 program. J. Ivorra-Martinez thanks Generalitat Valenciana - GVA for funding a postdoc position through the CIAPOS program co-funded by ESF Investing in your future, grant number CIAPOS/2023/362. Funding for open access charge: Universitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Detecting AI adoption at scale: a web mining and LLM methodology

  • Pastor-Merino, Ana
  • Martínez-Barbero, Xavier|||0000-0002-6040-8118
  • Domenech, Josep|||0000-0002-7302-5810
[EN] The recent emergence of Artificial Intelligence (AI) technologies has created multiple opportunities for companies. The growing interest in AI adoption has led to an increase in technological innovations and business applications. At the same time, web mining techniques have been used to monitor technological trends, often through basic natural language processing methods. However, advances in Large Language Models (LLMs) enable a more detailed and in-depth analysis of web content, necessitating the development of new methodologies. This paper proposes a methodology for integrating LLMs into the technology mining of corporate websites, with a focus on Spanish companies. The study uses data collected in 2023 and 2025, applying web scraping techniques to gather textual information. The analysis process involves automated AI detection, manual validation, and evaluation through standard classification metrics. The findings contribute to a better understanding of AI adoption trends and inform future research on tech mining applications for industry., This work was supported by the Generalitat Valenciana under Grant CIAICO/2023/272; the Agencia Estatal de Investigacion (MCIN/AEI/10.13039/501100011033) and ERDF/EU under Grant PID2023-152106OB-I00; and the Universitat Politecnica de Valencia (PAID-01-24, PAID-12-25).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Proposal for a Gas Sensor Device to Classify Hydrobiological Species and Estimate Non-Refrigeration Time

  • Silva-Alvarado, Vinie Lee|||0009-0000-5857-3248
  • Díaz-Blasco, Francisco Javier|||0009-0009-1458-7547
  • Lloret, Jaime|||0000-0002-0862-0533
  • Parra, Lorena
  • Aldana, Cristhian
  • Saavedra, Yesenia
[EN] The quality of hydrobiological species for human consumption, such as fish and shellfish, is crucial to ensure their safety. This article highlights the use of Metal Oxide Semiconductor Resistive (MOSR)-based MQ sensor modules, along with temperature and humidity, to analyze these species. The prototype is based on the use of an Arduino Mega 2560 Rev3 to connect the sensors with data stored on a Raspberry Pi 4, which can be accessed via Wi-Fi for downloading. Machine learning (ML) models were applied to classify and estimate non-refrigeration time with different quantities of variables, using species such as Illex argentinus, Sardina pilchardus, Scomber colias, and Sepia pharaonis. In total, 33 classification models and 28 regression models were employed. The best results were obtained with Boosted Trees model, achieving an accuracy of 99.93% in the validation phase and 99.74% in the testing phase. In the regression models to estimate non-refrigeration time, with 38 variables, the best model was Bagged Trees, with an R-squared of 0.995 for the validation phase and 0.997 for the testing phase., This work was supported in part by the ThinkInAzul Programme; and in part by the Ministerio de Ciencia e Innovación (MCIN) through the Project SistIA under European Union NextGenerationEU, Generalitat Valenciana, and Consejo Nacional de Ciencia, Tecnología e Innovación (CONCYTEC) under Grant PRTR-C17.I1 and Grant THINKINAZUL/2021/002.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development of a Novel Convolution to Interactive Capture and Recalibration Enhancement Module for Underwater Fish Detection in Sensor Networks

  • Silva-Alvarado, Vinie Lee|||0009-0000-5857-3248
  • Ahmad, Ali|||0000-0001-5530-7374
  • Sendra, Sandra|||0000-0001-9556-9088
  • Lloret, Jaime|||0000-0002-0862-0533
[EN] Underwater optical sensor networks are essential for fish monitoring, yet imagery is often affected by illumination variability, low contrast, and complex backgrounds. Attention mechanisms are vital for feature representation in deep networks, yet existing approaches often struggle with spatial information loss and limited multi-scale interaction under such challenging conditions. This paper introduces Convolution to Interactive Capture and Recalibration Enhancement (C2ICARE), a lightweight attention module designed to overcome these challenges. The principal contribution of C2ICARE is the adaptation of memory interaction principles into an edge-oriented attention framework that enhances feature discrimination while maintaining computational efficiency. The architecture employs three core innovations: a 1:3 memory-feature split to preserve context while reducing cost, parallel multi-scale depthwise convolutions (3 × 3 and 7 × 7) for fine-grained and broad feature extraction, and a cross-branch interaction mechanism coupled with a ConvNeXt-style feed-forward network that avoids dimensionality reduction. Experimental results on an underwater fish dataset demonstrate that YOLO26n with C2ICARE achieves a mean average precision (mAP@0.5:0.95) of 0.7033, outperforming Coordinate Attention (+3.8%), FasterBlock (+1.7%), and CBAM (+0.4%) while adding only 0.05M parameters and 0.16 GFLOPs. Multi-objective Pareto Frontier analysis confirms that C2ICARE provides an effective balance between accuracy, efficiency, and generalization for resource-constrained deployment. EigenCAM visualizations further validate that the model focuses on biological morphology rather than background noise. Its lightweight design enables seamless integration with underwater sensor networks and fog platforms for real-time fish detection in aquaculture, commercial fisheries, and scientific research. Future work will investigate broader marine applications and cross-platform deployment scenarios. The code is available on GitHub., Financial support was provided by the Grant PRE2021-100809 funded by Agencia Estatal de Investigación (AEI) MICIU/AEI/10.13039/501100011033, by European Social Fund Plus (ESF+), and by Universitat Politècnica de València through the Programa de Ayudas de Investigación y Desarrollo (PAID-01-24) .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Ethylene brassylate as a biobased plasticizer for poly(lactic acid): Evaluation of mechanical, thermal, and biodegradation properties

  • Escriva-Faus, M.
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Mario Nicolás
  • Lázaro-Hernández, C.|||0009-0002-8250-9363
  • Sanchez-Nacher, Lourdes|||0000-0002-8627-4576
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
[EN] Poly(lactic acid) (PLA) is a bio-based polymer with high potential; however, its inherent brittleness restricts its practical applications. This work evaluates ethylene brassylate (EB), a macrocyclic diester of natural origin, as a plasticizer for PLA at 5¿20 wt%. Thermal analysis confirmed a plasticizing effect, with the glass transition temperature decreasing from 59.9 °C in neat PLA to 38.0 °C in PLA-20 EB. Mechanical tests showed that 20 wt% EB increased elongation at break from 10 % (neat PLA) to over 460 % and improved impact resistance by ~70 %. Furthermore, moisture resistance was preserved, and microscopy confirmed good miscibility with no phase separation. Under composting, degradation occurs more rapidly in proportion to EB content, reaching ~90 % mass loss after four weeks. Migration tests revealed values below 40 mg kg¿1 for PLA-EB < 10 wt% EB, whereas PLA-15 EB reached the regulatory limit. EB is therefore an efficient bio-based plasticizer for PLA, offering enhanced ductility, toughness, and biodegradation, with promising applications in sustainable packaging, especially for refrigerated and cold-chain storage., This research is a part of the grant PID2023-152869OB-C22, and the grant TED2021-131762A-I00, funded by MCIN/AEI/10.13039/ 501100011033 and by the European Union NextGenerationEU /PRTR. The authors also thank Generalitat Valenciana - GVA, grant number CIGE/2023/46 and CIAICO/2023/253, for supporting this work. Microscopy services at UPV are also acknowledged for their help in collecting and analyzing FESEM images. D.L. thanks Generalitat Valenciana - GVA for funding a postdoc position through the CIAPOS program cofunded by ESF Investing in your future, grant number CIAPOS/2022/140. C. Lazaro-Hdez thanks Generalitat Valenciana - GVA for funding a predoc position through the CIACIF program co-funded by ESF Investing in your future, grant number CIACIF/2023/244. M. Miranda-Pinzon thanks the Vice-rectorate for Research of the Universitat Politecnica de Valencia (UPV) for funding a predoctoral contract in the PAID-01-24 program. Funding for open access charge: CRUE-Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Does AI boost firm productivity? A web scraping and LLMs approach

  • Pastor-Merino, Ana
  • Martínez-Barbero, Xavier|||0000-0002-6040-8118
  • Domenech, Josep|||0000-0002-7302-5810
  • Vicente, María R.
[EN] Artificial Intelligence (AI) is widely seen as a transformative technology with the potential to reshape firm productivity across sectors. However, empirical evidence on its actual impact at the firm level remains limited, mainly due to the lack of extensive firm-level data. Leveraging web scraping and Large Language Models (LLMs), this study develops a novel framework to detect and quantify AI adoption among 62,525 Spanish firms. The approach distinguishes between firms that adopt AI and those that integrate it intensively across business functions, constructing both binary and continuous measures of AI use. Using entropy-balanced instrumental variable estimations to address endogeneity, we find that AI-adopting firms exhibit approximately 53%¿55% higher sales and 48% higher value added than comparable non-adopters. Moreover, increasing the intensity of AI use is associated with an even larger productivity premium of 74%¿76% in sales and up to 67% in value added, highlighting the substantial returns from deeper AI integration. In dynamic terms, AI adoption is linked to 9%¿13% faster annual sales growth. These findings provide evidence that AI significantly enhances firm performance, underscoring its role as a key driver of productivity growth., This work was supported by the Generalitat Valenciana, Spain under Grant CIAICO/2023/272; the Agencia Estatal de Investigacion, Spain (MCIN/AEI/10.13039/501100011033) and ERD-F/EU under Grant PID2023-152106OB-I00; and the Universitat Politecnica de Valencia, Spain (PAID-01-24) and FPU24/01116, Ministerio de Ciencia e Innovacion (Spain).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Generalized Chi distribution for non-integer degrees of freedom in modelling biological collectivities

  • Castro-Palacio, Juan Carlos|||0000-0002-0132-9989
  • Fernández de Córdoba, Pedro|||0000-0002-0347-7280
  • González-Cortés, Álvaro|||0009-0001-2328-2173
  • Isidro, J.M.|||0000-0002-0720-9945
  • Noverques-Medina, Aina|||0000-0002-7810-0381
  • Sánchez Pérez, Enrique Alfonso|||0000-0001-8854-3154
  • Orellana-Panchame, Marcos Fabricio
  • Sahu, Saira
[EN] This article aims to expand the practical potential of the Chi and Chi-square distributions by extending their applicability to non-integer degrees of freedom, k. The study has two main objectives: first, to explore and leverage the relationship between the Chi, Chi-square, and Gamma distributions to interpret non-integer degrees of freedom; and second, to apply this framework to real survival-time data in the context of biological and health sciences. Three specific cases are analyzed: the germination times of Pinus tropicalis Morelet seeds cultivated in western Cuba; the interval between infection by virulent tuberculous bacilli and death from tuberculosis in guinea pigs; and the period from the onset of symptoms to death due to COVID-19 in patients in Mexico during 2020. A parameter estimation was performed by maximum likelihood (MLE), and the optimal value of k was found to be non-integer in all cases., We would like to acknowledge funding from the Generalitat Valenciana (Spain) through the PROMETEO CIPROM/2023/32 grant, and from the Agencia Estatal de Investigacion (Spain) through ¿the PID2022-142407NB-I00 and PID2024-162480OB-I00 grants. The work of S.S. is partially supported by DGAPA-UNAM (Mexico) Project No. IN103522. The author A.G.C. was supported ¿ by a contract of the Programa de Ayudas de Investigacion y Desarrollo (PAID-01-24), Universitat ¿Politecnica de Val ` encia
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Spectral Characterization of UAV Attitude Degradation Under Real-Time Vision Workloads: A SITL Framework for Pre-Deployment Diagnosis

  • Quispe-Checca, Esau
  • Sacoto-Cabrera, Erwin J.
  • Eddu Guerrero Laurente, Geyson
  • Mego, L. Walter Utrilla
  • Moreno-Cardenas, Edison
  • Silva-Alvarado, Vinie Lee|||0009-0000-5857-3248
  • Lloret, Jaime|||0000-0002-0862-0533
[EN] Real-time vision inference executed concurrently with unmanned aerial vehicle (UAV) flight control can introduce computational delays that couple with the attitude control loop and degrade dynamic stability. This work presents a spectral characterization of the disturbance induced by embedded vision workloads on a quadrotor controlled by cascaded Proportional-Integral-Derivative (PID) loops. A Software-In-The-Loop (SITL) platform based on PX4 Autopilot, Gazebo Classic 11, and ROS2 Humble was employed. A YOLO26n detector was used exclusively as a controlled computational stressor, generating latency regimes of 2.5 ms with GPU acceleration and 84.8-90.7 ms under CPU inference. Experimental results show that CPU inference induces a narrowband elevation in the power spectral density (PSD) of roll and pitch concentrated in the 1-3 Hz band. At 2.0 m altitude, pitch PSD increased by 9.07 & times; (+10.6 dB), while under in-ground-effect (IGE) conditions at 1.5 m the disturbance decreased to 1.82 & times; (+5.9 dB). A continuous altitude sweep revealed a maximum amplification of 698 & times; near the IGE/out-of-ground-effect transition when the camera pipeline remained coupled to the simulator physics loop. Architectural isolation experiments show that the dominant degradation mechanism is not the latency magnitude but the temporal coupling of the inference pipeline to the dynamics integrator: a decoupled pipeline with higher median latency produced no spectral elevation. An analytical critical latency threshold of lambda(crit)approximate to 76 ms was derived from the delay margin of the outer position loop; this threshold only becomes active when the pipeline is coupled to the control loop. A closed-loop sensitivity analysis predicts a resonance peak inside the 1-3 Hz band, consistent with the measurements. Finally, three quantitative pre-deployment indicators are proposed as SITL-derived reference values for validating real-time vision systems integrated into PID-controlled UAV platforms operating in controlled low-wind environments such as greenhouses., This work was supported in part by the Universidad Nacional San Antonio Abad del Cusco (UNSAAC) through the projects of the Professional School of Electronic Engineering, in part by the Universidad Politecnica Salesiana through the Fog Computing Simulation Project, and in part by the Universitat Politecnica de Valencia through the Programa de Ayudas de Investigacion y Desarrollo under Grant PAID-01-24.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Machine Learning-Driven Computer Vision System for Automated Fat and Energy Quantification in Human Milk Microcapillaries

  • Huamanga-Chumbes, Lujan E.
  • Sacoto-Cabrera, Erwin J.
  • Huicho-Mendigure, Alfz
  • Moreno-Cardenas, Edison
  • Lloret, Jaime|||0000-0002-0862-0533
  • Silva-Alvarado, Vinie Lee|||0009-0000-5857-3248
[EN] Neonatal health requires precise lipid quantification in human milk to ensure proper nutritional development. Traditional manual methods, such as the creamatocrit, are limited by human-induced bias and significant measurement uncertainty. This study presents a low-cost Computer Vision System acting as an automated optical sensing modality for estimate the cream fraction (c) using advanced Machine Learning regression, which is subsequently used to derive fat and energy quantification through established analytical equations. The system is optimized for the Gold-LED spectrum, which enhances the dynamic range to 226 a.u. for robust feature extraction. We evaluated 28 distinct ML regression models across three feature spaces (Gray Scale, RGB, and Combined). The results, based on 6400 samples, demonstrate that the Rational Quadratic GPR model achieved the highest predictive stability with a coefficient of determination of R2=0.867. This computational framework achieved a 57.5% reduction in relative error compared to manual benchmarks. SHAP analysis indicates that the model selectively attributes higher importance to Red channel intensities and Blue contrast gradients, which correspond to the optical scattering characteristics of lipid globules. These findings validate the system as a stable sensing modality for non-invasive quantification. The proposed architecture integrates cost-effective hardware with high-precision analytical modeling, offering a reagent-free and operationally feasible alternative for standardized nutritional assessment in neonatal intensive care units and milk banks., This work was supported in part by the National University of San Antonio Abad of Cusco, through the projects of the Professional School of Electronic Engineering; the Universidad Politecnica Salesiana under the Fog Computing Simulation project; and the Universitat Politecnica de Valencia through the "Programa de Ayudas de Investigacion y Desarrollo (PAID-01-24)".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Computational analysis of the in-cylinder mixture formation in a direct injection hydrogen spark-ignition engine

  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
  • Gerardo
  • Barbery, I.
[EN] Hydrogen is considered a vital solution for decarbonizing road transport due to its ability to operate efficiently at high dilution levels, thereby reducing nitrogen oxide (NOx) emissions and enhancing engine efficiency. This study delves into the fundamental phenomena governing air-fuel mixture formation in a spark-ignition (SI) engine fueled with hydrogen, with a focus on the effects of turbulence and in-cylinder airflow. To achieve this, a bespoke computational methodology was developed, combining constant-pressure test rig and engine simulations. The accuracy of these simulations was validated against experimental data for fuel injection, mixture formation, and combustion in both cases. A comprehensive parametric study was conducted via numerical simulations, exploring the effects of varying start-of-injection (SOI) timings and air-fuel ratios (A) on the mixing process. The results reveal that injection timing has a profound impact on the mixing process, imposing critical constraints on combustion initiation and pollutant emissions. Late injections-SOI timing of-130 CAD aTDC-result in a highly stratified mixture in terms of equivalence ratio (cent), with a difference of almost 85% between the average global equivalence ratio (cent = 0.94) and the target equivalence ratio cent = 0.38 at the onset of combustion. The temperature field also shows some degree of stratification, although for the case of the most delayed injection, the average mixture temperature is reduced by more than 5%. Notably, the hydrogen stratification dominates over the temperature stratification, yet they exhibit a clear correlation that could potentially inhibit NOx production. The enhanced reactivity of hydrogen-rich mixtures may be offset by lower mixture temperatures, an effect that becomes more pronounced as the overall dilution ratio decreases: in the most diluted case (A = 2.2), a reduction of around 3% in the average temperature of the mixture is observed with respect to the A = 3.2 case. This is attributed to the increased mixture reactivity, which leads to higher NOx emissions while preventing engine misfire. Ultimately, this study provides valuable insights into the complex interactions governing hydrogen injection in spark-ignition engines, shedding light on the optimization of injection strategies and operating conditions to minimize pollutant emissions and improve engine efficiency, thereby contributing to the development of more sustainable and environmentally friendly transportation solutions., G. Alcarria-Laserna is partly supported by an FPI contract (FPI-S2-22-91149) of the "Programa de Apoyo para la Investigacion y Desarrollo (PAID 01-24)" of the Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Valorization of oil-extraction chia seed flour into injection-moulded biocomposites: Influence of plasticizers

  • Domínguez-Candela, Iván|||0000-0003-3288-1079
  • Irene Boronat-Castellar
  • Mario Nicolás
  • Fombuena, Vicent|||0000-0001-7266-6205
  • Martinez-Felipe, A.
[EN] The valorization of agro-industrial by-products into scalable bioplastics is a key strategy for developing sustainable materials. In this work, chia seed flour (CSF), a by-product of cold oil extraction with medium protein (~41¿wt%) and high carbohydrate (~36¿wt%), was directly transformed into injection-moulded biocomposites without protein purification, using an industrially scalable extrusion¿injection moulding route. CSF was plasticized with water, glycerol, sorbitol, and their combinations (40¿60¿wt%). Plasticizer type and content strongly influenced intermolecular interactions, mechanical and thermomechanical performance, thermal stability, water uptake, and compost disintegration. Glycerol/sorbitol systems showed the highest ductility (elongation at break: 18¿31.7%), whereas water/sorbitol formulations exhibited the highest stiffness (tensile modulus: 134¿315¿MPa) due to partial sorbitol crystallization. Water/glycerol systems provided the best balance between mechanical performance and structural stability under water uptake conditions. Overall, the results demonstrate the feasibility of converting oil-extraction-derived CSF into biodegradable, injection-mouldable biocomposites through an industrially relevant process., I. Dominguez-Candela thanks Generalitat Valenciana GVA for funding a postdoc position through the CIAPOS program co-funded by ESF Investing in your future, grant number CIAPOS/2024/341. M. M. Miranda-Pinzon thanks the Vice-rectorate for Research of the Universitat Politecnica de Valencia (UPV) for funding a predoctoral contract in the PAID-01-24 program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

The effect of plasticizers on properties of thermoplastic rice protein processed by extrusion and injection molding

  • Peñafiel-Alvarado, J.I.
  • Stefani, P.M.
  • Mario Nicolás
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Balart, Rafael|||0000-0001-5670-7126
[EN] The manufacturing of rice protein (RP) thermoplastic materials by combining it with urea, glycerol, sorbitol and xylitol by extrusion and injection molding techniques are studied in this work. Very promising protein-based sustainable polymeric materials are obtained, with tensile strength superior to 17 MPa in the case of samples plasticized with urea, which allows to obtain very rigid materials. On the other hand, the combination of RP and urea with glycerol, sorbitol or xylitol gives rise to materials with elongation at breaks superior to 40 %. This means a wide range of properties depending on the combination of plasticizers used. Urea crystals finely embedded in the RP matrix are observed by microscopy analysis, which are confirmed by the presence of a melting peak in DSC at approximately 127 °C. Chemical analysis also revealed the predominance of these urea crystals through chemical analysis. Dynamic-mechanical thermal analysis (DMTA) also showed the glass transition temperature (Tg) of the materials to be between 28 and 60 °C, being the sample with glycerol the one with the lowest value. All materials were observed to be completely biodegradable at 3¿4 weeks, gaining increasing environmentally friendly value. The plenty availability of rice protein makes these materials very attractive for producing environmentally friendly materials with great potential in the food industry., This research is a part of the grant PID2023-152869OB-C22, and the grant TED2021-131762A-I00, funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU /PRTR. The authors also thank Generalitat Valenciana - GVA, grant number CIGE/2023/46 and CIAICO/2023/253, for supporting this work. Funded with Aid for First Research Projects (PAID-06-22), Vice-rectorate for Research of the Universitat Polit`ecnica de Val`encia (UPV). J. G.-C. wants to thank FPU20/01732 grant funded by MCIN/AEI/10.13039/501100011033 and by ESF Investing in your future. J. Ivorra-Martinez thanks Generalitat Valenciana - GVA for funding a postdoc position through the CIAPOS program co-funded by ESF Investing in your future, grant number CIAPOS/2023/362. M. Miranda-Pinzon thanks Vicerectorate for Research of the Universitat Polit`ecnica de Val`encia (UPV) for funding a predoctoral contract in the PAID-01-24 program. Microscopy services at UPV are also acknowledged for by their help in collecting and analyzing FESEM images. Funding for open access charge: CRUE-Universitat Polit`ecnica de Val`encia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Biomechanical mapping of tumor growth: A novel method to quantify glioma infiltration and mass effect

  • López-Mateu, Carlos
  • Gómez-Mahiques, María
  • Montosa-Micó, Víctor
  • Gil-Terrón-Rodríguez, Francisco Javier|||0000-0002-3536-6462
  • Garcia-Gomez, Juan M
  • Fuster García, Elíes|||0000-0002-0716-8960
  • Sederevicius, Donatas
  • Emblem, Kyrre E.
[EN] Background: Glioblastoma (GBM) growth can alter surrounding brain tissue through location-dependent physiological changes. Two main growth phenotypes¿(I) infiltrative, characterized by diffuse invasion with minimal mass effect, and (II) proliferative, characterized by pronounced tissue compression¿are recognized, but their quantitative characterization and prognostic impact remain poorly explored. Purpose: To develop and validate a novel MRI-based biomarker, the Dynamic Infiltration Rate (DIR), that quantitatively assesses the balance between tumor volume expansion and peritumoral compression, and to evaluate its prognostic ability for stratifying patients based on overall survival (OS). Methods: The DIR was defined as the ratio between tumor-volume enlargement and mass-effect-induced peritumoral compression. Technical validation was conducted using synthetic datasets with known ground truth spanning realistic infiltrative-proliferative spectra. Clinically, patients were dichotomized into high- and low-infiltration groups using a threshold optimized by maximizing the log-rank statistic for OS. Prognostic evaluation included multivariate Cox regression adjusted for age, sex, and MGMT methylation status. Results: The synthetic dataset validation demonstrated high concordance with ground truth (R² = 0.89). Clinical evaluation indicated significantly improved OS in the low DIR group (median = 35.2 weeks) compared to the high DIR group (median = 16.0 weeks; p = 0.0001). DIR effectively stratified patients based on survival (log-rank p < 0.001, HR = 2.49) and remained an independent prognostic factor on multivariate analysis (HR = 1.45, 95% CI 1.07¿1.85; p = 0.0159). Conclusions: The DIR is a novel and robust quantitative MRI biomarker capable of distinguishing between proliferative and infiltrative GBM phenotypes, independently predicting OS. Early phenotype identification could facilitate personalized treatment strategies and individualized follow-up scheduling., MCIN/AEI (Ministerio de Ciencia, Innovación y Universidades / Agencia Estatal de Investigación), Grant/Award Numbers: PID2024156848OB-I00, PID2021-127110OA-I00, PDC2025-165365-I00, FPU23/02431; Generalitat Valenciana, Grant/Award Numbers: INVEST/2022/298 (ProgramaINVESTIGO), CIAICO/2022/064(Lalaby-Glio), INNEST/2022/87(SINUÉ); European Research Council, Grant/Award Numbers: 758657-ImPRESS, 101213953-CHRONOS; Helse Sør-Øst RHF, Grant/Award Numbers: 2021057, 2017073, 2023050; Research Council of Norway, Grant/Award Numbers: 325971, 261984, 303249, 32543, 356066; Norwegian Cancer Society, Grant/Award Number: 309012 - SAFARI; Universitat Politècnica de València, Grant/Award Number: PAID-01-24(Subprogram1)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Ethical Recommendations for Conversational Design in Intelligent Voice Assistants for Older Adults: Alexa as a Case Study

  • Medina-Medina, Nuria
  • Gilaberte, Raquel Lacuesta
  • Hervas, Eva M.
  • Silva-Alvarado, Vinie Lee|||0009-0000-5857-3248
  • Lloret, Jaime|||0000-0002-0862-0533
[EN] The widespread adoption of intelligent voice assistants makes understanding the ethical implications of their interaction design-particularly for older adults-essential. This population is especially sensitive to conversational design decisions due to asymmetries in digital literacy, trust management, and social vulnerability. We present a controlled empirical study wherein older adults evaluated two approaches to Alexa's conversational design: one emphasizing neutrality and transparency, and another relying on emotional manipulation and opacity. We first identify eight key ethical dimensions relevant to conversational voice assistant design and develop a questionnaire to assess users' perceived ethicality in this context. Our findings provide evidence of how manipulative design strategies are associated with changes in participants' perceptions of the ethical behavior of the voice assistant. Based on these results, we propose a set of ethical design recommendations for conversational assistants aimed at promoting the ethical well-being of older adults., This work was primarily funded by the University of Iowa through contract N040400-NMO with the University of Granada and by the Spanish Ministry of Science, Innovation and Universities through project PID2022-136779OB-C31 (PLEISAR) . Additional support was provided through contracts RTI2018-096986-B-C32 and C-ING-179-UGR23, as well as by Universitat Politecnica de Valencia under contract PAID-01-24.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Multivariate Gas Sensor E-Nose System with PARAFAC and Machine Learning Modeling for Quantifying and Classifying the Impact of Fishing Gears

  • Silva-Alvarado, Vinie Lee|||0009-0000-5857-3248
  • Lloret, Jaime|||0000-0002-0862-0533
[EN] The quality of seafood is intrinsically linked to the accumulated history of stress, feeding, handling, and physical damage imposed by the fishing gear employed. This study proposes an innovative methodology using an E-nose sensor. The study species was Sparus aurata. Eight fishing gears were studied. The methodology integrates Parallel Factor Analysis (PARAFAC) for impact quantification and Machine Learning (ML) for classifying the fishing gear of origin. Longline was established as the method with the lowest deviation. The impact hierarchy, from highest to lowest deviation, is as follows: Aquaculture 50.61% (95% CI: 34%, 68%), Purse seine 37.92% (95% CI: 22%, 54%), Trawl 35.92% (95% CI: 21%, 51%), Gillnet (three panels) 27.69% (95% CI: 14%, 41%), Gillnet (single panel) 24.63% (95% CI: 9%, 40%), Gillnet (two panels) 18.12% (95% CI: 4%, 31%) and Hook and line 1.36% (95% CI: ¿10%, 13%). For the classification task, 33 ML models were evaluated. Subspace KNN model yielded the best results with an accuracy of 97.14% in the validation and 98.08% in the testing, using 35 variables. Using 10, 15, 20, 25, and 30 variables, an accuracy higher than 85% was achieved. These results demonstrate the high precision in fish traceability by exploiting the sensor response profile left by each fishing gear., This work has been funded by the Ministerio de Economía y Competitividad through the Project TED2021-131040B-C31. This study also forms part of the ThinkInAzul programme and was supported by MCIN with funding from European Union NextGenerationEU (PRTR-C17.I1) and by Generalitat Valenciana (THINKINAZUL/2021/002). The author V.L.S.-A. is supported by a contract from the Universitat Politècnica de València through the Programa de Ayudas de Investigación y Desarrollo (PAID-01-24) .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Understanding the role of thermo-diffusive instabilities in hydrogen combustion for lean-burn spark-ignition engine operation

  • Novella Rosa, Ricardo|||0000-0002-5123-6924
  • Gómez-Soriano, Josep|||0000-0002-2742-9224
  • González-Domínguez, David
  • Olaciregui-Fontalvo, Orlando Mario
[EN] This study introduces a novel numerical approach for modeling hydrogen combustion in lean-burn spark-ignition engines, incorporating thermo-diffusive instabilities (TDI) within a CFD URANS-based framework. The study focuses on identifying potential sources of prediction errors and validating the robustness of the methodology under different operating conditions. The results indicate that the method performs well within moderate dilution ratios, but its accuracy decreases at higher dilution levels (e.g., lambda = 3.4), where predictions become less reliable. Analysis of the turbulent flame regime reveals that the coupling between TDI and turbulence is not adequately reproduced at high dilution ratios, suggesting that certain phenomena are not captured by the model. Including TDI effects significantly improves the model ability to replicate experimental trends, with a substantial increase in predictive accuracy. However, some limitations remain in predicting hydrogen combustion under realistic internal combustion engine (ICE) operating conditions, highlighting the need for further research to refine the model. The results have significant implications for the development of more efficient and environmentally friendly engines, as hydrogen is considered a promising fuel for reducing greenhouse gas and nitrogen oxide emissions in the transportation sector., O. Olaciregui is partly supported by an FPI contract (FPI-S2-2264270) of the "Programa de Apoyo para la Investigacion y Desarrollo (PAID 01-24)" of the Universitat Politecnica de Valencia.