Skip to main content

DESARROLLO E IRRADIACION DE ALEACIONES DE ALTA ENTROPIA, MATERIALES DE BASE COBRE Y ACEROS ODS NANOESTRUCTURADOS PARA REACTORES DE FUSION

PID2019-105325RB-C33

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Call year 2019
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSIDAD CARLOS III DE MADRID

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Exploring CuCrFeVTi system to produce high entropy alloys for high heat flux applications

  • Rodríguez-López, A.
  • Savoini, B.
  • Monge, M. Ángeles
  • Muñoz, A.
  • Pérez Zubiaur, Pablo
CuCrFeVTi, CuCrFeVTi, CuCrFeVTi and CuCrFeVTi were produced by low-pressure arc-melting to evaluate the feasibility of developing reduced activation high entropy alloys containing copper. The materials present a dendritic microstructure and some Cu and Ti segregation in the as-cast condition, being the CuCrFeVTi the most homogenous alloy. Copper particles, with a mean size of about 10 nm, are found distributed inside the dendrites. The volume fraction of the copper particles is ~ 7 times higher in the alloy with 5 at.% Cu content that in the alloy with 20 at.%, with values ranging from 22 ± 5 to 3 ± 2 particles/μm. Combination of massive Berkovich nanoindentation, statistical analysis and analytical scanning electron microscopy, has been successful for determining the hardness and elastic modulus values of each phase and quantifying their contribution to microhardness values obtained by standard Vickers microindentation., This research has been supported by Agencia Estatal de Investigación (PID2019-105325RB-C33 / AEI / 10.13039/501100011033) and by the Regional Government of Madrid through the program TECHNOFUSIÓN(III)CM (S2018/EMT-4437).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Production and characterization of the Cr35Fe35V16.5Mo6Ti7.5 high entropy alloy

  • Ortega, Y.
  • Monge, M. Ángeles
  • Savoini, B.
  • Muñoz, A,
  • Pérez Zubiaur, Pablo
The microstructure, thermal stability, and mechanical properties of a novel CrFeVMoTi high-entropy alloy were studied. The mechanical properties were mapped by nanoindentation, and the results correlated with the microstructure and the Vickers microhardness measurements. The alloy was produced by arc melting in a low pressure He atmosphere. Thermal treatments were performed to study the thermal stability of the alloy. The as-cast microstructure of the alloy exhibited a body-centered cubic phase with morphology of dendrites, outlined by a very thin interdendritic phase with a crystallographic structure compatible with FeTi. The presence of the intermetallic particles was predicted by a free-energy based model, in contrast with the single solid solution alloy predicted by a parameter-based model. The volume fraction of the dendrites in the alloy is ∼ 94 % after arc melting. A small fraction of sparse Ti-rich particles, ∼0.4 vol%, was observed. The thermal treatments produced an increase of the population of Ti-rich particles, the formation of a σ-phase and nucleation of precipitates enriched with Fe and Ti into the previous dendrites. The material in as-cast condition exhibited a microhardness value of 6.2 ± 0.3 GPa, while the alloy aged at 960 °C resulted in 7.1 ± 0.4 GPa. Nanoindentations maps showed an excellent correlation with the microstructure, and their statistical analyses yielded a nanohardness mean value of 8.2 ± 0.4 GPa in the dendritic BCC regions of the as-cast and thermal treated samples and 14.1 ± 0.6 GPa for the σ-phase. The onset of the plastic behavior has been studied by analyzing the pop-in phenomenon observed in the nanoindentation loading curves. For the as-cast alloy, this analysis showed that the elastic-to-plastic transition seems to be triggered by dislocation nucleation. The alloy has a low thermal diffusivity in the measured temperature range that increases on increasing temperature., This research has been supported by the Agencia Estatal de Investigación of Spain (PID2019-105325RB-C33/AEI/10.13039/501100011033) and by the Regional Government of Madrid through the program TECHNOFUSIÓN(III)CM (S2018/EMT-4437), project cofinancing with Structural Funds (ERDF and ESF). The support of the Madrid Government (Comunidad de Madrid-Spain) through the Multi-annual Agreement with UC3M ( Excellence of University Professors – EPUC3M14 and in the context of the V PRICIT - Regional Programme of Research and Technological Innovation) is also acknowledge.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Influence of 2 (wt%) titanium addition on the oxidation resistance of tungsten

  • Pérez Zubiaur, Pablo
  • Monge, M. Ángeles
The oxidation behaviour of W-2Ti (wt%) alloy has been evaluated in dry air at 600, 700 and 800 °C for 100 h and the kinetics compared with those for pure tungsten. Titanium addition exerts a beneficial effect on the oxidation resistance of pure tungsten. The mass gain is almost five times smaller than in the case of commercial tungsten and three times smaller than that of tungsten prepared by powder metallurgy at 600 °C. This effect is even higher at 700 and 800 °C, where the titanium addition suppresses catastrophic oxidation of pure tungsten. Major influence of titanium regards the suppression of massive microcracking in the scale, avoiding the development of the typical non-protective multilayered scale pattern formed on pure tungsten., This research was supported by the Agencia Estatal de Investigación of Spain (PID2019-105325RB-C33/AEI/10.13039/501100011033) and by the Regional Government of Madrid through TECHNOFUSIÓN(III)CM (S2018/EMT-4437) project cofinanced by Structural Funds (ERDF and ESF). The support of the Regional Government of Madrid through the multi-annual agreement with UC3M (Excellence of University Professors–EPUC3M14 and in the context of the V PRICIT - Regional Programme of Research and Technological Innovation) is also acknowledge.