Skip to main content

FABRICACION ADITIVA DE COMPUESTOS METAL-CERAMICA Y RECUBRIMIENTOS AVANZADOS A PARTIR DE SUSPENSIONES COLOIDALES

PID2019-106631GB-C42

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Call year 2019
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Exploitation of Lignocellulose Fiber-Based Biotemplates to Improve the Performance of an Immobilized TiO2 Photocatalyst

  • González Granados, Zoilo
  • Yus, Joaquín
  • Bravo, Yessica
  • Sánchez-Herencia, A. Javier
  • Ferrari, Begoña
The performance of an immobilized photocatalyst has been successfully improved by colloidal processing of a heterostructure composed by TiO<sub>2</sub> nanoparticles and lignocellulose nanofibers (LCNFs) obtained from biomass residues. The incorporation of 4 wt.% of biotemplate to the formulation increased the degradation rate and reduced the operating time to remove the 100% of methyl orange of a liquid solution. The reaction rate constant (<i>k</i> = 0.29–0.45 h<sup>−1</sup>) of the prepared photocatalytic coatings (using commercial particles and templates obtained from natural-derived resources) are competitive with other pure TiO<sub>2</sub> materials (no composites), which were prepared through more complex methodologies. The optimization stages of deposition and sintering processes allowed us to obtain homogeneous and crack-free microstructures with controlled thickness and mass values ranging from 3 to 12 µm and 0.9 to 5.6 mg, respectively. The variation of the microstructures was achieved by varying the amount of LCNF in the formulated suspensions. The versatility of the proposed methodology would allow for implementation over the internal surface of photocatalytic reactors or as a photocatalytic layer of their membranes. In addition, the processing strategy could be applied to immobilize other synthetized semiconductors with higher intrinsic photocatalysis properties., This research was supported by the projects S2018/NMT-4411 (Comunidad de Madrid) and PID2019-106631GB-C42 (MINECO/FEDER). Z. Gonzalez acknowledges the Spanish Ministry of Economy and Competitiveness for the Postdoctoral Fellowship: IJCI-2016-28538., This work was supported by FCT-Fundação para a Ciência e a Tecnologia (project PEst-OE/QUI/UI0674/2019, CQM, Portuguese government funds), through the Madeira 14–20 Program, project PROEQUIPRAM Reforço do Investimento em Equipamentos e Infraestruturas Científicas na RAM (M1420-01-0145-FEDER-000008) by ARDITI-Agência Regional para o Desenvolvimento da Investigação Tecnologia e Inovação, through project M1420-01-0145-FEDER-000005—Centro de Química da Madeira CQM + (Madeira 14–20). SM was supported by the postdoctoral fellowship granted by ARDITI CQM + project (ARDITI-CQM/2017/008-PDG). RP was supported by an FCT postdoctoral grant (SFRH/BPD/97387/2013)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Colloidal processing and sintering of WC-based ceramics with low Ni content as sintering aid

  • García Ayala, Esperanza Macarena
  • Silvestroni, L.
  • Yus, Joaquín
  • Ferrari, Begoña
  • Pastor, J.Y.
  • Sánchez-Herencia, A. Javier
To soften the extreme sintering conditions of Tungsten Carbide (WC), a 3 wt.% of metallic nickel (Ni) was added to the starting powders. To ensure a fair distribution of the second phase and an intimate mixture of the phases, the colloidal process was adopted. A commercial Ni and a in-house synthesised nanosized nickel were used as sintering aids. Rheological studies allowed a high dispersion of the nickel in the final composite powders. Sintering studies by Hot-Pressing route (HP) proved the great benefices of Ni as a sintering aid, decreasing the maximum temperature necessary to achieve full densification, from 1900 to 1450 °C and dwell times from 20 to 7 min. Among all the materials obtained, the best results in terms of density, microstructure and properties were obtained for WC-nNi, which achieved hardness of 14.8 GPa and toughness comparable to conventional cermets with much higher content of metallic phase., This work has been supported by the Spanish Government under contracts PID2019-106631GB-C42 and C44 (MICINN/FEDER, UE) and Madrid Regional Government under contract P2018/NMT-4411 (Comunidad de Madrid/FEDER, UE). Mrs. García-Ayala thanks MINECO/FEDER, UE by grant BES-2016-079038 and JECS Trust for a mobility grant (ref: 2018170) for three months to ISTEC. Authors thank A. Sangiorgi for advice and support running the HP cycles.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Tesis doctoral (DoctoralThesis)

Aqueous colloidal processing of W and WC-based composites, sintering and mechanical properties at high temperature

  • García Ayala, Esperanza Macarena
E. M. Garcia-Ayala, Z. Gonzalez, B. Ferrari, J. Y. Pastor, A. J. Sanchez-Herencia, Colloidal Approach to the Additive Manufacturing of W-based Materials, in: EuroPM 2018 Proceedings (2020) ISBN: 978-1-899072-50-7. E.M. Garcia-Ayala, S. Tarancon, B. Ferrari, J.Y. Pastor, A.J. Sanchez-Herencia, "Thermomechanical behaviour of WC-W2C composites at first wall in fusion conditions", Int. J. Refract Metal. Hard Mater., 98 105565 (2021). DOI: 10.1016/j.ijrmhm.2021.105565 E.M.Garcia-Ayala, L.Silvestroni, J.Yus, B.Ferrari, J.Y.Pastor and A.J.Sanchez-Herencia"Colloidal processing and sintering of WC-based ceramics with low Ni content as sintering aid", J. Eur. Ceram. Soc, 41 (3) 1848, -1858 (2021).DOI: 10.1016/j.jeurceramsoc.2020.10.038 M.E. Garcia-Ayala, S. Tarancon, Z. Gonzalez, B. Ferrari, J.Y. Pastor, A.J. Sanchez-Herencia, "Processing of WC/W composites for extreme environments by colloidal dispersion of powders and SPS sintering",Int. J. Refract. Met. Hard Mater., 84,105026 ( 2019,)DOI:10.1016/j.ijrmhm.2019.105026, [EN] There have been many advanced technologies that operates at high temperature under severe conditions, such as those over the inner walls of the future fusion nuclear reactor (ITER, DEMO, etc.). Refractory metals such as tungsten are proposed as optimum materials to face these conditions. Pure ceramics, such as WC and metal ceramics are proposed also as alternative materials for the components that require operate at high temperature under high wear conditions or neutronic damage. For that reason, the design of complex compositions and microstructures is necessary to achieve reliable materials under these conditions. That makes this work investigate on colloidal processing W and WC materials, as well as their composites with nickel for softening of the sintering conditions. Aqueous colloidal processing is proposed as an alternative to the solvent-less techniques. By the study of zeta potential and chemical analysis of powders suspended in water the optimal conditions for high solid content suspension preparation were determined at different pH conditions and considering the use a cationic dispersant (polyethyleneimine, PEI). The rheological studies have determined the maximum solid content through the Krieger-Dougherty model adjustment, so the time spent removing water after powder preparation can be diminished. Three different types of composite powders were prepared: WC-W, WC-Ni and W-Ni. For WC-W composites, the amount of metallic phase was fixed in 10, 20 and 50 vol.%, while for WC-Ni and W-Ni mixtures, the amount of metallic nickel phase was 5 vol.% (3 wt.%). Three different sintering methods are used: Spark Plasma Sintering (SPS), Hot-Press Sintering (HPS) and Vacuum Sintering (VS). WC-W materials were sintered by SPS at 1700 and 1800 oC for 10 min and 60 MPa. The crystalline and chemical studies determined the high reactivity between W and WC during the thermal cycle, which gives place to the presence of a third species: tungsten semicarbide (W2C), which provoked all the W consumption. Mechanical tests at high temperatures for the W2C/WC composites demonstrated their excellent properties and performance at conditions similar to the ITER divertor walls. A self-reinforcement behaviour due to the appearing of metallic tungsten in the microstructure as the temperature approach to 1200 ºC is described. On the other hand, mixture of WC with Ni and W with Ni, obtained by aqueous colloidal processing were sintered by the three mentioned sintering techniques and the differences between them studied. Two types of Ni powders were used: a commercial nickel (cNi) and a nanometric nickel synthesized in the lab (nNi). WC-Ni sintered by HPS achieved a density higher than 98%, which was not the case of SPS and VS sintered samples. SEM/EDX observations demonstrated that sintering was by a solution-precipitation mechanism that leaved the nickel located in the grain junctions, while there were slight carbon precipitations favoured by the thermodynamical conditions during the thermal cycle. For W-Ni alloys, successful results were obtained from VS process, achieving 96% density and a fully dense microstructure. In this case, W and Ni reacts while thermal treatment, giving an intermetallic species: NiW. For both WC-Ni and W-Ni materials, the presence of small amounts of Ni showed a clear softening of sintering conditions, which make the sintering of W and WC an affordable method for wide productions in terms of both technology and economic cost. Mechanical tests of these composites exhibited a ductilisation of the materials due to the presence of the nickel phase, which matches to the data found in the literature for this type of composites and alloys., [ES] Existen multitudes de tecnologías avanzadas capaces de operar a alta temperatura bajo condiciones severas, como aquellos que conforman las paredes interiores de futuros reactores de fusión nuclear (ITER, DEMO, etc.). Los metales refractarios como el wolframio se proponen como los materiales óptimos para trabajar bajo estas condiciones. Los cerámicos puros, como el WC, y los composites cerámica-metal (cermets) también se presentan como claras alternativas para aquellos materiales requeridos para operaciones a alta temperatura, bajo alto desgaste o radiación neutrónica. Por este motivo, el diseño de composiciones complejas y microestructuras es necesario para lograr la preparación de materiales que trabajen en dichas condiciones. Todo ello hace que se profundice en la Investigación de materiales de W y WC formulados por procesamiento coloidal, así como sus materiales compuestos con níquel metálico para suavizar sus condiciones de sinterización. El procesamiento coloidal en base acuosa se propone como una fuerte alternativa a las tradicionales técnicas sin disolvente (en seco). Mediante el estudio del potencial zeta y el análisis químico de los polvos suspendidos en agua, las condiciones óptimas para la preparación de suspensiones con alto contenido en sólidos se determinaron a diferentes valores de pH, y considerando el uso de un dispersante catiónico (polietilenimina o PEI). Los estudios reológicos determinaron el máximo contenido en sólidos mediante el ajuste de Krieger-Dougherty, de tal forma que se lograba disminuir el tiempo de eliminación de disolvente. Se prepararon tres tipos diferentes de polvos compuestos: WC-W, WC-Ni y W-Ni. Para los composites WC-W, la cantidad de fase metálica se fijó en 10, 20 y 50 vol.%, mientras que para las mezclas WC-Ni y W-Ni, la cantidad de níquel metálico fue de un 5 vol.% (3% en peso). Se emplearon tres métodos distintos de sinterización: Sinterización asistida por Corriente Pulsada (SPS), Sinterización por presión asistida en caliente (HPS) y Sinterización a vacío (VS). Los materiales de WC-W se sinterizaron por SPS a 1700 y 1800 oC durante 10 minutos, a 60 MPa de presión. Los estudios químicos y de cristalinidad determinaron la alta reactividad entre W y WC durante el ciclo térmico, el cual dio lugar a la aparición de una tercera especie: el semicarburo de wolframio (W2C), lo que provocó el agotamiento total del wolframio metálico. Los ensayos mecánicos a alta temperatura para los compuestos W2C/WC demostraron sus excelentes propiedades a condiciones similares a las del divertor del ITER. Se describe un comportamiento de refuerzo mecánico debido a la aparición de wolframio metálico en la microestructura, a medida que se describe un ascenso de la temperatura hasta los 1200 oC. Por otra parte, las mezclas de WC con Ni, y W con Ni, obtenidas mediante procesamiento coloidal en agua, se sinterizaron a través de las tres técnicas ya mencionadas, por lo que se estudiaron los diferentes resultados. Se usaron dos tipos de polvo de Ni: un níquel comercial (cNi), y un níquel nanométrico sintetizado en el laboratorio (nNi). WC-Ni se sinterizó por HPS, logrando una densidad mayor al 98%, lo que no ocurrió en el caso de las muestras sinterizadas por SPS y VS. Los análisis por SEM/EDX demostraron que la sinterización seguía un mecanismo de disolución-precipitación, lo que provocó la localización del níquel metálico en los límites de grano, mientras que aparecieron algunas precipitaciones de grafito favorecidas por las condiciones termodinámicas durante el ciclo térmico. Para las aleaciones W-Ni, se obtuvieron resultados bastante exitosos para el proceso de sinterización a vacío (VS), alcanzando densidades superiores al 96%, así como una microestructura consolidada y totalmente densificada. En este caso, W y Ni reaccionan durante el tratamiento térmico, dando lugar a una nueva especie: el intermetálico NiW. Para ambos composites WC-Ni y W-Ni, la presencia de pequeñas cantidades de Ni mostró un claro suavizamiento de las condiciones de sinterización, lo que hace que la sinterización de W y WC se conciba como un método asequible para grandes producciones a escala industrial en términos tanto tecnológicos como económicos. Los ensayos mecánicos de estos materiales exhibieron una clara ductilización debido a la presencia de fase níquel, lo que coincide con los datos encontrados en la literatura para este tipo de composites y aleaciones., Esta tesis se enmarca en el proyecto MAT2015-70780-C4-1-P del plan nacional, titulada “Procesamiento coloidal en medio acuoso de composites en base W y WC, sinterización y propiedades mecánicas a alta temperatura”. Este trabajo se ha desarrollado combinando las principales líneas de investigación de los dos grupos en los cuales se ha llevado a cabo el trabajo experimental: la Química Coloidal desarrollada por el grupo Tailoring through Colloidal Processing (ICV-CSIC), y el conocimiento sobre propiedades mecánicas del grupo CIME (UPM).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Microstructural and Mechanical Characterization of Colloidal Processed WC/(W5Vol%Ni) via Spark Plasma Sintering

  • Zegai, Ahmed-Ameur
  • Besharatloo, Hossein
  • Ortega-Columbrans, Pablo
  • Djerdjare, Boubekeur
  • Ferrari, Begoña
  • Sánchez-Herencia, A. Javier
This study investigates the sintering behaviour and properties of WC-based composites in which WC was mixed with W5vol%Ni in concentrations of 10vol% and 20vol%. Colloidal processing in water and spark plasma sintering were employed to disperse the WC particles and facilitate sintering. The addition of W5vol%Ni improved the sintering process, as evident from a lower onset temperature of shrinkage determined through dilatometric studies. All samples exhibited the formation of tungsten monocarbide (W2C), with a more pronounced presence in the WC/20(W5vol%Ni) composite. Sintering reached its maximum rate at 1550 °C and was completed at 1600 °C, resulting in a final density exceeding 99.8%. X-ray diffraction analysis confirmed the detection of WC and W2C phases after sintering. The observed WC content was higher than expected, which may be attributed to carbon diffusion during the process. Macro-scale mechanical characterisations revealed that the WC/10(W5vol%Ni) composite exhibited a hardness of 18.9 GPa, while the WC/20(W5vol%Ni) composite demonstrated a hardness of 18.3 GPa. Increasing the W5vol%Ni binder content caused a decrease in mechanical properties due to the formation of W2C phases. This study provides valuable insights into the sintering behavior and properties of WC/W5vol%Ni composites, offering potential applications in extreme environments., This research was supported by the Spanish Government through the projects PID2019–106631GB-C41/C42 and TED2021-129920B-C41 funded by MCIN/AEI/10.13039/501100011033 and by the “European Union NextGenerationEU/PRTR”., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Processing of membranes and 3D scaffolds based on n-TiO2 colloidally dispersed on a thermoplastic matrix for photocatalytic pollutant removal

  • Ortega-Columbrans, Pablo
  • Ferrández-Montero, Ana
  • Yus, Joaquín
  • Sánchez-Herencia, A. Javier
  • Ferrari, Begoña
[EN] One of the most promising technologies for water treatment today is photocatalytic membrane reactors (PMRs). Manufacturing efficient membranes is still challenging as many factors are involved, like the porosity, specific surface area, nature and size of particles. In this work, a colloidal method to self-support commercial nanoparticles (n-TiO) in a polymeric matrix of polylactic acid (PLA) is proposed allowing the fabrication of 2D and 3D structures with high inorganic content that can be adapted to the PMR configurations. Using a commercial filament of PLA loaded with up to 15 vol% of n-TiO2 as starting point, photocatalytic membranes have been manufactured by FFF. In addition, following a similar process, tapes with n-TiO2 particles up to 15 vol% have been processed by tape casting. Thermal characterisation (DTA) and dynamic rheometry evaluated the commercial filament for printing to determine the conditions used during the thermal extrusion and printing processes. FTIR and XRD technologies were used to determine the chemical interactions of PLA matrices with TiO nanoparticles. Porosity was measured by Archimedes's method for the filaments, by mercury intrusion for the membranes and by optical microscopy for the scaffolds. Finally, the microstructure of the 2D and 3D pieces was evaluated by scanning microscopy. 2D tape cast membranes were compared with individual filaments and 3D printed scaffolds in linear and gyroidal geometries. The catalytic activity results indicate that tape cast membranes show much higher kinetic constants than the individual filaments and the linear and gyroidal scaffolds. Regarding the two different printed scaffolds, in contrast to the kinetic values, gyroidal geometries achieve an average degradation time (t) of 6.1 h, which is a lower value than those observed for linear scaffold geometries. Methyl orange degradation tests after 24 h exposure under UV light showed degradation rates of 98% for membranes, 90% for commercial filaments, 80% for gyroidal scaffolds and 60% for linear patterns. Therefore, these results are promising as a solution for fabricating easily extractable self-supported membranes for water treatment in PMRs., This work has been supported by the Spanish Government (Agencia Estatal de Investigación) through the projects PID2019–106631 GB-C42 (MICRO@Mater) and TED2021–129920B-C41 (EC0FOOTPrint), both cofunded by AEI/10.13039/501100011033/Uni´on Europea NextGenerationEU/PRTR). Pablo Ortega Columbrans acknowledges the Comunidad de Madrid for the industrial doctorate support through the contract IND2022/IND-23603.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Material thermal extrusion of conductive 3D electrodes using highly loaded graphene and graphite colloidal feedstock

  • Urra Sánchez, Oxel
  • Besharatloo, Hossein
  • Yus, Joaquín
  • Sánchez-Herencia, A. Javier
  • Ferrari, Begoña
[EN] Evolution in the energy storage field requires the development of more sustainable and efficient high-performance electrochemical storage devices (EESDs). Additive manufacturing (AM) opens unique opportunities to improve the efficiency and the electrochemical response by the design of 3D electrodes and the increasing of exposed active surface area impossible to achieve by other processing techniques. In other to reach high-performance EESDs, carbonaceous species are well-established as electroactive materials owing to their electronic properties, low cost, and sustainable origin. Although the materials have been widely investigated, there is a lack of feedstock development for the fabrication of EESDs by AM technologies. This work presents the fabrication of metals free light conductive filaments for material thermal extrusion (MTE) by formulating PLA-based composites with a high content of colloidal graphite and graphene (15–25 vol%). By the colloidal characterization and surface modification of the carbonaceous species, an improved distribution and enhanced platelet/polymer bond were achieved, provoking the inorganic phase's orientation during the extrusion process. Prepared filaments were characterized to analyze the influence of the microstructural anisotropy on thermal, thermorheological, mechanical, and electrical properties. Subsequently, developed filaments were used to print complex electrodes by MTE, enhancing the electrochemical properties of the electrodes with superior control of the macrostructural design. The developed colloidal filaments with an oriented inorganic microstructure, not only allow a defined shaping of the outer structure of the electrodes but also let the design of completely different microstructures. Consequently, different microstructural configurations were printed increasing the number of conduction paths in the polymeric matrix to achieve high electric conductivities (22 S.m) in printed electrodes., This work has been supported by the Spanish Government (Agencia Estatal de Investigacion) ´ through the projects PID2019-106631GB-C42 (AEI/10.13039/501100011033) and the Regional Government of Madrid through the program ADITIMAT, ref. P2018/NMT-4411, both cofounded by the European Regional Development Fund (FEDER/ ERDF). H. Besharatloo acknowledge the Spanish Government for its postdoctoral support through Margarita Salas grant., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Reaction behavior during Spark Plasma Sintering of cBN-TiCN-Ni powders

  • Mineiro, Ricardo
  • Fernandes, C.M.
  • Silva, E.L.
  • Soares, M.R.
  • Figueiredo, D.
  • Ferrari, Begoña
  • Sánchez-Herencia, A. Javier
  • Senos, A.M.R.
[EN] Polycrystalline cubic boron nitride (PcBN) is the designation given to composites constituted by cBN hard particles within a ceramic/metallic matrix. These composites are normally processed in severe pressure and temperature conditions to achieve full densification and prevent hexagonal BN formation, which would decrease the composite hardness. In this work, the Spark Plasma Sintering (SPS) technique was investigated as an alternative to sinter cBN-TiCN based composites, with and without addition of metallic Ni. The initial compositions were selected according with calculated phase diagrams, using the Thermo-calc software. The thermal behavior during SPS was studied up to 2000°C, namely the densification, reactivity and phase transformations. A larger densification was achieved with Ni addition, but full removal of open porosity was only possible at 1700 °C, where the cBN phase transformation to hBN completely occurred. In agreement with the thermodynamic calculations, other matrix phases, as TiB2 and Ni3B, were formed during sintering., This research is sponsored by FEDER funds through COMPETE, Programa Operacional Factores de Competividade, 3DCompcer (POCI-01-0247-FEDER-047060). The authors are grateful to the JECS Trust for funding this work between the Department of Materials and Ceramic Engineering, University of Aveiro (Portugal), and the Institute of Ceramic and Glass (ICV-CSIC) (Spain) (Contract No. 2020257). This work was developed within the scope of the project CICECO-Aveiro Institute of Materials, UIDB/50011/2020, UIDP/50011/2020 & LA/P/0006/2020, financed by national funds through the FCT/MCTES (PIDDAC) and also within PID2019-106631GB-C42 of the Spanish Government., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of Lateral Laser-Cladding Process on the Corrosion Performance of Inconel 625

  • Rezayat, Mohammad
  • Sani, Amirhossein Aboutorabi
  • Noghani, Mohammad Talafi
  • Saghafi Yazdi, Morteza
  • Taheri, Morteza
  • Moghanian, Amirhossein
  • Mohammadi, Mohammad Abedini
  • Moradi, Mahmoud
  • Mateo García, Antonio Manuel
  • Besharatloo, Hossein
[EN] This study aimed to evaluate the corrosion properties of different samples coated by the laser-cladding method to find the optimal laser parameters. Thereby, potentiodynamic polarization (Tafel) and electrochemical impedance tests were performed to assess the corrosion resistance of coated samples. Consequently, the corrosion morphology of tested samples was inspected by scanning electron microscopy. The results demonstrated that the laser power directly correlates with pitting corrosion and defects on the surface of the samples. Moreover, when molybdenum and chromium ions are increased in the electrolyte solution, the passive and protective layers are more durable, as the ions are sited within the holes and defects, reducing the surface corrosion rate., This research was funded by Financial support from the Spanish Government (Agencia Estatal de Investigación) grant number PID2019-106631GB-C41/C42 and PGC2018-096855-B-C41. And The APC was funded by Regional Government of Madrid through the program ADITIMAT (S2018/NMT-4411), Spanish Government for its postdoctoral support (Margarita Salas 2022) and AGAUR, Agency for Administration of University and Research (Agència de Gestió d’Ajuts Universitaris i de Recerca) (2021 SGR 01053)., Peer reviewed
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Micropillar compression of Ti(C,N)-FeNi cermets: Microstructural, processing, and scale effects

  • Besharatloo, Hossein
  • de Nicolás Morillas, M.
  • Chen, Ming
  • Mateo, A.
  • Ferrari, Begoña
  • Gordo, Elena
  • Jiménez Piqué, Emilio
  • Wheeler, Jeff
  • Llanes, Luis
The influence of microstructure and processing route on the small-scale mechanical response as well as on the deformation and failure mechanisms of Ti(C,N)-FeNi cermets were investigated by uniaxial compression of micropillars milled by focused ion beam with different sizes. Stress-strain curves were determined and associated deformation mechanisms were observed in-situ using scanning electron microscopy. The appropriate micropillars dimension was assessed, based on the microstructural characteristics of studied cermets, to overcome scale effect issues. A direct relationship was observed between yield strength and ceramic/metal ratio for colloidal samples. Meanwhile, deformation of metallic binder and glide between Ti(C,N)/Ti(C,N) particles were evidenced as dominant mechanisms during the compression for colloidal cermets with 70 and 80 vol% of ceramic phase, respectively. The obtained results illustrate that samples processed from powder attained by colloidal route provide superior mechanical behavior, as compared to that exhibited by specimens shaped following a conventional powder metallurgy one (wet ball-milling/drying)., 8 páginas