Skip to main content

INTEGRIDAD MICROMECANICA DE MATERIALES COMPUESTOS CERAMICA-METAL PROCESADOS POR MANUFACTURA ADITIVA

PID2019-106631GB-C41

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Call year 2019
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSITAT POLITECNICA DE CATALUNYA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 11
Encontrada(s) 1 página(s)

RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

Micropillar compression of Ti(C,N)-FeNi cermets: Microstructural, processing, and scale effects

  • Besharatloo, Hossein
  • de Nicolás Morillas, M.
  • Chen, Ming
  • Mateo, A.
  • Ferrari, Begoña
  • Gordo, Elena
  • Jiménez Piqué, Emilio
  • Wheeler, Jeff
  • Llanes, Luis
The influence of microstructure and processing route on the small-scale mechanical response as well as on the deformation and failure mechanisms of Ti(C,N)-FeNi cermets were investigated by uniaxial compression of micropillars milled by focused ion beam with different sizes. Stress-strain curves were determined and associated deformation mechanisms were observed in-situ using scanning electron microscopy. The appropriate micropillars dimension was assessed, based on the microstructural characteristics of studied cermets, to overcome scale effect issues. A direct relationship was observed between yield strength and ceramic/metal ratio for colloidal samples. Meanwhile, deformation of metallic binder and glide between Ti(C,N)/Ti(C,N) particles were evidenced as dominant mechanisms during the compression for colloidal cermets with 70 and 80 vol% of ceramic phase, respectively. The obtained results illustrate that samples processed from powder attained by colloidal route provide superior mechanical behavior, as compared to that exhibited by specimens shaped following a conventional powder metallurgy one (wet ball-milling/drying)., 8 páginas
RODIN. Repositorio de Objetos de Docencia e Investigación de la Universidad de Cádiz
Publication Artículo científico (JournalArticle)

High-temperature wettability in hard materials: Comparison of systems with different binder/carbide phases and evaluation of C addition

  • de Nicolás Morillas, M.
  • Llanes, L.
  • Gordo, E.
Metal-ceramic wettability is a decisive parameter in the high-temperature sintering of hard materials. Wettability tests enable the study of this property with minimum material waste, especially useful in the search of alternative systems to WC-Co hardmetals. In this investigation, Fe-based binders – FeNiCr and FeCrAl – were tested on Ti(C,N) and WC substrates, aiming to assess: the high-temperature interactions, the dissolutive character of the liquid phase and the nature of the interphases generated, and the influence on sintering behaviour. As a result, FeNiCr led to excellent wetting scenarios for both ceramics, whereas FeCrAl alloys induced the formation of aluminium oxides. The effect of C addition on wettability was also evaluated, resulting in an improvement of this property by the inclusion of this element in the binder phase. Inspection of the microstructures resultant from powder metallurgy processing of the different configurations confirmed their excellent correlation with wettability results. As a consequence, the effectivity of this technique as a model of the sintering scenario could be asserted., 17 páginas
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Microstructural and Mechanical Characterization of Colloidal Processed WC/(W5Vol%Ni) via Spark Plasma Sintering

  • Zegai, Ahmed-Ameur
  • Besharatloo, Hossein
  • Ortega-Columbrans, Pablo
  • Djerdjare, Boubekeur
  • Ferrari, Begoña
  • Sánchez-Herencia, A. Javier
This study investigates the sintering behaviour and properties of WC-based composites in which WC was mixed with W5vol%Ni in concentrations of 10vol% and 20vol%. Colloidal processing in water and spark plasma sintering were employed to disperse the WC particles and facilitate sintering. The addition of W5vol%Ni improved the sintering process, as evident from a lower onset temperature of shrinkage determined through dilatometric studies. All samples exhibited the formation of tungsten monocarbide (W2C), with a more pronounced presence in the WC/20(W5vol%Ni) composite. Sintering reached its maximum rate at 1550 °C and was completed at 1600 °C, resulting in a final density exceeding 99.8%. X-ray diffraction analysis confirmed the detection of WC and W2C phases after sintering. The observed WC content was higher than expected, which may be attributed to carbon diffusion during the process. Macro-scale mechanical characterisations revealed that the WC/10(W5vol%Ni) composite exhibited a hardness of 18.9 GPa, while the WC/20(W5vol%Ni) composite demonstrated a hardness of 18.3 GPa. Increasing the W5vol%Ni binder content caused a decrease in mechanical properties due to the formation of W2C phases. This study provides valuable insights into the sintering behavior and properties of WC/W5vol%Ni composites, offering potential applications in extreme environments., This research was supported by the Spanish Government through the projects PID2019–106631GB-C41/C42 and TED2021-129920B-C41 funded by MCIN/AEI/10.13039/501100011033 and by the “European Union NextGenerationEU/PRTR”., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Micromechanical mapping of polycrystalline cubic boron nitride composites by means of high-speed nanoindentation: Assessment of microstructural assemblage effects

  • Gordon, S.
  • Besharatloo, Hossein
  • Wheeler, J.M.
  • Rodriguez-Suarez, T.
  • Roa, J.J.
  • Jiménez-Piqué, Emilio
  • Llanes, L.
[EN] Polycrystalline cubic boron nitrides (PcBNs) are composites widely used as cutting tool materials due to their exceptional high hardness and wear resistance. Investigation of their micromechanical properties is key for optimizing PcBN’s performance through microstructural design. Within this context, high-speed nanoindentation is proposed and implemented, for three different PcBN grades, to correlate microstructure with local mechanical properties. A total of 40,000 imprints were performed in each grade. The obtained mechanical maps and data sets are statistically treated following two deconvolution approaches: 1D and 2D Gaussian fitting. The use of high-speed nanoindentation is validated not only by the reliable assessment of the intrinsic mechanical properties of cBN particles, binder and interphase region, but also by the successful mirroring of microstructural assemblage within the mechanical maps attained. Comparison of the results determined from 1D and 2D gaussian representations are in satisfactory agreement. Nevertheless, some difficulties and disparity between them arises when involving fine-grained microstructures., Work was supported by the Spanish Ministerio de Ciencia, Innovación y Universidades MICINN - FEDER (Spain) through grants PGC2018-096855-B-C41 and PID2019-106631GB-C41 (AEI/10.13039/501100011033), as well as by the industry-university collaborative program among Element Six, Seco Tools and UPC., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Micropillar compression of Ti(C,N)-FeNi cermets: Microstructural, processing, and scale effects

  • Besharatloo, Hossein
  • Nicolás-Morillas, M. de
  • Chen, M.
  • Mateo, A.
  • Ferrari, Begoña
  • Gordo Odériz, Elena
  • Jiménez-Piqué, Emilio
  • Wheeler, J.M.
  • Llanes, L.
[EN] The influence of microstructure and processing route on the small-scale mechanical response as well as on the deformation and failure mechanisms of Ti(C,N)-FeNi cermets were investigated by uniaxial compression of micropillars milled by focused ion beam with different sizes. Stress-strain curves were determined and associated deformation mechanisms were observed in-situ using scanning electron microscopy. The appropriate micropillars dimension was assessed, based on the microstructural characteristics of studied cermets, to overcome scale effect issues. A direct relationship was observed between yield strength and ceramic/metal ratio for colloidal samples. Meanwhile, deformation of metallic binder and glide between Ti(C,N)/Ti(C,N) particles were evidenced as dominant mechanisms during the compression for colloidal cermets with 70 and 80 vol% of ceramic phase, respectively. The obtained results illustrate that samples processed from powder attained by colloidal route provide superior mechanical behavior, as compared to that exhibited by specimens shaped following a conventional powder metallurgy one (wet ball-milling/drying)., The authors want to acknowledge the financial support from the Spanish Government (Agencia Estatal de Investigación) through the projects PID2019–106631GB-C41/C42/C43 (AEI/10.13039/501100011033) and PGC2018–096855-B-C41, Fondo Europeo de Desarrollo Regional (FEDER) and the Regional Government of Madrid through the program ADITIMAT, ref. P2018/NMT-4411. H. Besharatloo and M. de Nicolás-Morillas acknowledge the Spanish Government for its postdoctoral support through Margarita Salas grants. Finally, the authors would like to thank Dr. Miguel de Dios for his efforts as one of the experts who helped colloidal processing to become functional for new cermets., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of Lateral Laser-Cladding Process on the Corrosion Performance of Inconel 625

  • Rezayat, Mohammad
  • Sani, Amirhossein Aboutorabi
  • Noghani, Mohammad Talafi
  • Saghafi Yazdi, Morteza
  • Taheri, Morteza
  • Moghanian, Amirhossein
  • Mohammadi, Mohammad Abedini
  • Moradi, Mahmoud
  • Mateo García, Antonio Manuel
  • Besharatloo, Hossein
[EN] This study aimed to evaluate the corrosion properties of different samples coated by the laser-cladding method to find the optimal laser parameters. Thereby, potentiodynamic polarization (Tafel) and electrochemical impedance tests were performed to assess the corrosion resistance of coated samples. Consequently, the corrosion morphology of tested samples was inspected by scanning electron microscopy. The results demonstrated that the laser power directly correlates with pitting corrosion and defects on the surface of the samples. Moreover, when molybdenum and chromium ions are increased in the electrolyte solution, the passive and protective layers are more durable, as the ions are sited within the holes and defects, reducing the surface corrosion rate., This research was funded by Financial support from the Spanish Government (Agencia Estatal de Investigación) grant number PID2019-106631GB-C41/C42 and PGC2018-096855-B-C41. And The APC was funded by Regional Government of Madrid through the program ADITIMAT (S2018/NMT-4411), Spanish Government for its postdoctoral support (Margarita Salas 2022) and AGAUR, Agency for Administration of University and Research (Agència de Gestió d’Ajuts Universitaris i de Recerca) (2021 SGR 01053)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Processing of WC with Fe-based alternative binders: Adjustment of C content and effect of Cr addition

  • de Nicolás-Morillas, M.
  • Besharatloo, Hossein
  • Cabezas, L.
  • de la Mata, M.
  • Sales, D.L.
  • Pereira, L.
  • Müller-Grunz, A.
  • Bertalan, C.
  • Useldinger, R.
  • Llanes, L.
  • Gordo, E.
Alternative hard materials to traditional WC-Co are one of the main goals in the investigation efforts of both scientific and industrial communities. In this investigation, WC-based materials were designed and processed with different Fe alloys employing a powder metallurgy route. Two candidates were selected: FeCrAl and FeNiCr. The former showed the formation of aluminium oxides, which hindered a homogeneous metal-ceramic distribution. On the other hand, FeNiCr led to dense and optimised samples which were further characterised in terms of their mechanical properties and corrosion resistance. They revealed an excellent combination of hardness and toughness, comparable or even superior to industrial compositions containing Co. Selected Cr addition induced some segregation and formation of secondary carbides –in consonance with thermodynamic simulation results and as evidenced by optical microscopy, XRD and TEM analyses– with a decrease in the TRS value. However, massive nanoindentation tests revealed that it also led to improved intrinsic hardness of binder and composite (metal-ceramic) phases, as well as enhanced corrosion resistance in acidic media compared to Cr-free alternative and reference hardmetals. © 2023 Elsevier Ltd, The current investigation was supported by the Spanish Government (Agencia Estatal de Investigacion/Ministerio de Ciencia e Innovacion) and European Union through the project AEI/10.13039/501100011033 (PID2019-106631GB-C41/C43) and grants BES-2016-077340 (María de Nicol´as Morillas), PRE2020-092445 (Laura Cabezas), and Margarita Salas (María de Nicol´as Morillas and Hossein Besharatloo), as well as by the Regional Government of Madrid through the program ADITIMAT, ref. S2018/NMT-4411. M. de la Mata acknowledges the EMERGIA postdoctoral fellowship (EMC21-00294). Authors acknowledge Mr. Francisco J. Delgado for the preparation of FIB and the Electron Microscopy Division at SCCYT-UCA., Peer reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Influence of microstructural assemblage of the substrate on the adhesion strength of coated PcBN grades

  • Gordon Pozuelo, Sandra|||0000-0001-9131-9559
  • Roa Rovira, Joan Josep|||0000-0002-7440-0766
  • Rodríguez Suárez, Teresa
  • M'Saoubi, Rachid
  • Jiménez Piqué, Emilio|||0000-0002-6950-611X
  • Franca, Luiz F.P.
  • Llanes Pitarch, Luis Miguel|||0000-0003-1054-1073
Coated polycrystalline cubic boron nitride (PcBN) tools are increasingly used for industrial applications with stringent requirements. However, information on the mechanical integrity of these systems is quite limited. Within this context, the adhesion strength of two TiN/TiAlN-coated and microstructurally different PcBN substrates – high- and low-cBN content grades with metallic and ceramic binders, respectively – is investigated by means of Rockwell C indentation testing. In doing so, special attention is paid to substrate microstructure effects on emergence and evolution of damage as applied load is increased. For both coated systems, it is found that damage scenario evolves from early adhesive delamination within the contact area towards radial cracking and spalling outside the residual imprint. However, critical loads for transition between damage stages are discerned to depend on microstructural assemblage of the substrate. Higher resistance to radial cracking and delamination is exhibited by the high cBN-content grade, in agreement with its higher hardness and toughness. Failure micromechanisms associated with cracking and spalling are similar for both coated-PcBN systems. Very interesting, delamination outside the residual imprint is determined to be of cohesive nature within the substrate, an experimental fact resulting from interaction among indentation-induced radial, cone-like and lateral fissures in PcBN., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Critical assessment of two-dimensional methods for the microstructural characterization of cemented carbides

  • Fang, Shiqi|||0000-0002-2126-7930
  • Salán Ballesteros, Maria Núria|||0000-0001-9323-8883
  • Pauly, Christoph
  • Llanes Pitarch, Luis Miguel|||0000-0003-1054-1073
  • Mücklich, Frank T.
Cemented carbides, or hard metals, are ceramic–metal composites usually consisting of tungsten carbide particles bound by a cobalt-based alloy. They are the backbone materials for the tooling industry, as a direct consequence of the outstanding range of property combinations, depending on their effective microstructural assemblage, i.e., the physical dimensions and relative content of their constitutive phases. Hence, reliable microstructural characterization becomes key for hard metal grade selection and quality control. This work aimed to assess the practical twodimensional characterization methods for the most important one- and two-phase properties of cemented carbides, i.e., the carbide grain size, phase fraction, carbide contiguity, and binder mean free path. Three different methods—point, line, and area analysis—were implemented to characterize four microstructurally distinct grades. The images were acquired by optical and scanning electron microscopy, with the latter through both secondary and backscattered electrons. Results were critically discussed by comparing the obtained values of properties and the different characterization methodology. Inspection technique combinations were finally ranked based on accuracy, accessibility, and operability considerations. The line method was used to analyze all the properties, the area method, for the one-phase properties, and the point method, for only the phase fraction. It was found that the combination of optical microscopy and the line analysis method was suitable for a direct inspection and rapid estimation for carbides above fine grain size. The most precise results were achieved using line analysis of the images obtained by the backscattered electrons of the scanning electron microscope, The work leading to this publication was supported by the Feodor Lynen Research Fellowship of the Alexander von Humboldt Foundation, by the individual research grant from the Deutsche Forschungsgemeinschaft (DFG-425923019), by the Spanish Ministerio de Ciencia e Innovación MICINN-FEDER (Spain) through grant PID2019-106631GB-C41 (AEI/10.13039/501100011033), and by the “Open Access Publication Funding” program of the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation) and Saarland University. The work also obtained funding for the FIB/SEM instrument used for SEM imaging and EBSD by the Deutsche Forschungsgemeinschaft (INST 256/510-1 FUGG)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Influence of microstructural assemblage of the substrate on the adhesion strength of coated PcBN grades

  • Gordon Pozuelo, Sandra
  • Roa Rovira, Joan Josep
  • Rodríguez Suárez, Teresa
  • M'Saoubi, Rachid
  • Jiménez Piqué, Emilio
  • Franca, Luiz F.P.
  • Llanes Pitarch, Luis Miguel
Coated polycrystalline cubic boron nitride (PcBN) tools are increasingly used for industrial applications with stringent requirements. However, information on the mechanical integrity of these systems is quite limited. Within this context, the adhesion strength of two TiN/TiAlN-coated and microstructurally different PcBN substrates – high- and low-cBN content grades with metallic and ceramic binders, respectively – is investigated by means of Rockwell C indentation testing. In doing so, special attention is paid to substrate microstructure effects on emergence and evolution of damage as applied load is increased. For both coated systems, it is found that damage scenario evolves from early adhesive delamination within the contact area towards radial cracking and spalling outside the residual imprint. However, critical loads for transition between damage stages are discerned to depend on microstructural assemblage of the substrate. Higher resistance to radial cracking and delamination is exhibited by the high cBN-content grade, in agreement with its higher hardness and toughness. Failure micromechanisms associated with cracking and spalling are similar for both coated-PcBN systems. Very interesting, delamination outside the residual imprint is determined to be of cohesive nature within the substrate, an experimental fact resulting from interaction among indentation-induced radial, cone-like and lateral fissures in PcBN., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Critical assessment of two-dimensional methods for the microstructural characterization of cemented carbides

  • Fang, Shiqi
  • Salán Ballesteros, Maria Núria
  • Pauly, Christoph
  • Llanes Pitarch, Luis Miguel
  • Mücklich, Frank T.
Cemented carbides, or hard metals, are ceramic–metal composites usually consisting of tungsten carbide particles bound by a cobalt-based alloy. They are the backbone materials for the tooling industry, as a direct consequence of the outstanding range of property combinations, depending on their effective microstructural assemblage, i.e., the physical dimensions and relative content of their constitutive phases. Hence, reliable microstructural characterization becomes key for hard metal grade selection and quality control. This work aimed to assess the practical twodimensional characterization methods for the most important one- and two-phase properties of cemented carbides, i.e., the carbide grain size, phase fraction, carbide contiguity, and binder mean free path. Three different methods—point, line, and area analysis—were implemented to characterize four microstructurally distinct grades. The images were acquired by optical and scanning electron microscopy, with the latter through both secondary and backscattered electrons. Results were critically discussed by comparing the obtained values of properties and the different characterization methodology. Inspection technique combinations were finally ranked based on accuracy, accessibility, and operability considerations. The line method was used to analyze all the properties, the area method, for the one-phase properties, and the point method, for only the phase fraction. It was found that the combination of optical microscopy and the line analysis method was suitable for a direct inspection and rapid estimation for carbides above fine grain size. The most precise results were achieved using line analysis of the images obtained by the backscattered electrons of the scanning electron microscope, The work leading to this publication was supported by the Feodor Lynen Research Fellowship of the Alexander von Humboldt Foundation, by the individual research grant from the Deutsche Forschungsgemeinschaft (DFG-425923019), by the Spanish Ministerio de Ciencia e Innovación MICINN-FEDER (Spain) through grant PID2019-106631GB-C41 (AEI/10.13039/501100011033), and by the “Open Access Publication Funding” program of the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation) and Saarland University. The work also obtained funding for the FIB/SEM instrument used for SEM imaging and EBSD by the Deutsche Forschungsgemeinschaft (INST 256/510-1 FUGG), Postprint (published version)