Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

Docta Complutense
Publication Artículo científico (JournalArticle)

Evaluating the optimal time for amikacin administration with respect to haemodialysis using an in vitro pharmacodynamic simulation against epidemic nosocomial OXA-48 producing Klebsiella pneumoniae ST405 strains

  • Carcas, Antonio J.
  • Sevillano Fernández, David
  • González Hidalgo, Natalia
  • Alou Cervera, Luis
  • Gómez Gil, Rosa
  • Muñoz, Mario
  • Llanos, Lucía
  • Sánchez Villanueva, Rafael J.
  • Gonzalez Parra, Emilio
  • Giménez, María José
  • Aguilar, Lorenzo
Objectives: Bacterial viability and enrichment of resistance resulting from three different amikacin administration schedules with respect to haemodialysis (HD) were assessed against three OXA-48-producing Klebsiella pneumoniae isolated during an outbreak in a Spanish hospital. Methods: A previously described two-compartment dynamic system was used. Three possible amikacin administration schedules were simulated: (i) haemodialysis immediately after amikacin infusion (pre-HD); (ii) infusion immediately after haemodialysis (post-HD); and (iii) infusion at 50% interdialytic period. Amikacin standard dose (SD) and double dose (DD) were simulated for each schedule. Values of Cmax/MIC, Cmax/MPC (mutant prevention concentration), AUC0-48h/MIC, AUC0-48h/MPC and %TMSW (percentage of time that the concentration was inside the mutant selection window) were determined with experimental data and were correlated with the area under the bacterial killing curve of the total population and the resistant subpopulation. Results: Both with SD and DD, the pre-HD schedule resulted in increases at 48h in bacterial counts of the total population at the expense of enrichment of pre-existing resistant subpopulations from 12h onwards for all strains. The estimated %TMSW that prevented enrichment of resistant mutants was <61.5%. The AUC0-48h/MPC (with values of ≈40 being associated with countering of increases in resistant subpopulations) was better than the %TMSW as a predictive parameter. Conclusion: This study showed that the longest times concentrations were above the MPC (i.e. highest AUC0-48h/MPC, lowest %TMSW), the lowest enrichment of resistant subpopulations. This implies use of the highest possible amikacin dose (limited by toxicity) and post-HD as the best administration schedule.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Motivación en estudiantes de ingeniería: Un caso de estudio con teorías e instrumentos para su medida y desarrollo, Motivation on engineering students: A case study using theories and instruments for its measurement and development

  • López Fernández, Daniel
  • Alarcón Cavero, Pedro P.
  • Rodríguez Sánchez, Manuel
  • Casado Fuente, Mª Luisa
[ES] La motivación es una de las claves fundamentales en el rendimiento académico de los estudiantes universitarios, especialmente en el caso de las carreras de ingeniería, donde la dificultad que estas suponen acarrea en el estudiante una baja sensación de autoeficacia y unas altas cotas de absentismo y abandono. Desde hace tiempo el campo de la psicología ha abordado ampliamente el constructo de la motivación, y en las últimas décadas se han diseñado instrumentos psicopedagógicos como el MSLQ o el MAPE-3 que sirven para favorecer la motivación de los universitarios. Este trabajo presenta una selección de teorías que sirven para comprender los procesos motivacionales de las personas e identificar indicadores que resulten útiles para evaluar e incidir en la motivación de los estudiantes universitarios de ingeniería. En base a los indicadores encontrados se ha definido un instrumento que sirve para diagnosticar la motivación de los estudiantes de escuelas de ingeniería españolas y que se ha, [EN] Motivation is one of the key issues for the academic performance of university students, especially in engineering programs where their degree of difficulty leads to a low sense of self-efficacy and high rates of absenteeism and dropout in students. Since some time ago psychology has widely addressed the construct of motivation, and in recent decades psychopedagogic instruments, such as the MSLQ or the MAPE-3, have been designed in order to contribute to the motivation of university students. This paper presents a selection of theories, mainly framed on the understanding of the motivation processes and the identification of indicators that are useful to influence and evaluate the motivation of university engineering students. Based on these indicators, an instrument to diagnose students’ motivation of Spanish Engineering Universities has been defined. This instrument has been used in an empirical and descriptiveexploratory study, with 92 students of the University Politécnica of Madrid, El trabajo presentado en este artículo se ha elaborado parcialmente en el marco de los Proyectos de Innovación Educativa PT12_13_04000 (“Desarrollo de competencias emocionales en el ámbito de la UPM”) e IE12_13_60005 (“TutorialAction: Plataforma Software y Metodologías para la Acción Tutorial”) financiados por la Universidad Politécnica de Madrid.
Archivo Digital UPM
Publication Contribución de congreso (ConferenceOutput)

Motivation in engineering education: a framework supported by evaluation instruments and enhancement resources