Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effect of infill parameters on mechanical properties in additive manufacturing, Efecto de los parámetros del relleno sobre las propiedades mecánicas en fabricación aditiva

  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Ferrándiz Bou, Santiago|||0000-0001-7137-9298
  • Boronat, Teodomiro|||0000-0002-2144-2874
[EN] The purpose of this paper is to study and outline the effects of infill parameters (percentage and pattern) using fused deposition manufacturing on mechanical properties of PLA printed samples. Three infill patterns were tested (rectilinear, honeycomb and Hilbert curve) while infill percentage was tested at three levels (20, 60 and 90 per cent). The properties examined were tensile strength, tensile modulus, elongation, Charpy impact test, morphology of the fractures of tensile and impact test and thermo mechanical analysis. Also, a thermal analysis was done using differential scanning calorimetry to the raw polymer in order to determine the processing temperature. Results showed the influence of the filling parameters in 3D printing on the mechanical properties of the obtained part. The filling pattern greatly influences the mechanical properties of parts with low filling percentages. Honeycomb filling pattern is the one with better mechanical results. The complexity of the filling pattern influences on the processing time. Nozzle direction changes in complex patterns lengthen processing time. Results can significantly influence custom design and manufacturing of parts using material fused deposition modeling., [ES] El propósito de este trabajo es estudiar y esbozar los efectos de los parámetros del relleno (porcentaje y patrón) de la fabricación por deposición fundida sobre las propiedades mecánicas de probetas de PLA. Se han analizado tres patrones de relleno (rectilíneo, panal de abeja y curva Hilbert), y tres porcentajes de relleno distintos (20, 60 y 90 por ciento). Las propiedades examinadas fueron resistencia a la tracción, módulo de tracción, alargamiento, tenacidad utilizando ensayo Charpy, morfología de las fracturas de los ensayos de tracción e impacto y análisis termomecánico. Además, se realizó un análisis térmico utilizando calorimetría diferencial de barrido al polímero virgen para determinar la temperatura de procesamiento. Los resultados mostraron la influencia de los parámetros de llenado en la impresión 3D sobre las propiedades mecánicas de la pieza obtenida. El patrón de llenado influye en gran medida en las propiedades mecánicas de las piezas con bajos porcentajes de relleno. El patrón de relleno de panal de abeja es el que tiene mejores resultados mecánicos de los tres analizados. La geometría del patrón de relleno también influye sobre el tiempo de procesado. Los cambios de dirección de las boquillas en patrones complejos alargan el tiempo de procesamiento. Los resultados obtenidos pueden influir significativamente en el diseño y la fabricación de piezas a medida mediante el modelado de la deposición de material fundido., This work was supported by the POLISABIO program grant number (2019-A02). J. Ivorra-Martinez wants to thank UPV for the grant received through the FPI program, grant (SP20190011). L. Quiles-Carrillo wants to thank MECD for his FPU grant (FPU15/03812). D. Lascano wants to thank UPV for the grant received through the PAID-01-18 program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Manufacturing and Properties of Binary Blend from Bacterial Polyester Poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) and Poly(caprolactone) with Improved Toughness

  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Fenollar, Octavio|||0000-0003-4323-7414
  • Sanchez-Nacher, Lourdes|||0000-0002-8627-4576
  • Balart, Rafael|||0000-0001-5670-7126
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Verdu, Isabel
[EN] Polyhydroxyalkanoates (PHAs) represent a promising group of bacterial polyesters for new applications. Poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBH) is a very promising bacterial polyester with potential uses in the packaging industry; nevertheless, as with many (almost all) bacterial polyesters, PHBH undergoes secondary crystallization (aging) which leads to an embrittlement. To overcome or minimize this, in the present work a flexible petroleum-derived polyester, namely poly(e-caprolactone), was used to obtain PHBH/PCL blends with different compositions (from 0 to 40 PCL wt %) using extrusion followed by injection moulding. The thermal analysis of the binary blends was studied by means of differential scanning calorimetry (DSC) and thermogravimetry (TGA). Both TGA and DSC revealed immiscibility between PHBH and PCL. Mechanical dynamic thermal analysis (DMTA) allowed a precise determination of the glass transition temperatures (Tg) as a function of the blend composition. By means of field emission scanning electron microscopy (FESEM), an internal structure formed by two phases was observed, with a PHBH-rich matrix phase and a finely dispersed PCL-rich phase. These results confirmed the immiscibility between these two biopolymers. However, the mechanical properties obtained through tensile and Charpy tests, indicated that the addition of PCL to PHBH considerably improved toughness. PHBH/PCL blends containing 40 PCL wt % offered an impact resistance double that of neat PHBH. PCL addition also contributed to a decrease in brittleness and an improvement in toughness and some other ductile properties. As expected, an increase in ductile properties resulted in a decrease in some mechanical resistant properties, e.g., the modulus and the strength (in tensile and flexural conditions) decreased with increasing wt % PCL in PHBH/PCL blends., This research work was funded by the Spanish Ministry of Science, Innovation, and Universities (MICIU), project numbers MAT2017-84909-C2-2-R. This work was supported by the POLISABIO program, grant number (2019-A02). Juan Ivorra-Martinez is the recipient of an FPI grant from Universitat Politècnica de València (PAID-2019-SP20190011). Luis Quiles-Carrillo wants to thank GVA for his FPI grant (ACIF/2016/182) and MECD for his FPU grant (FPU15/03812). Microscopy services at UPV are acknowledged for their help in collecting and analyzing FESEM images.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Assessment of the Mechanical and Thermal Properties of Injection-Molded Poly(3-hydroxybutyrate-co-3-hydroxyhexanoate)/Hydroxyapatite Nanoparticles Parts for Use in Bone Tissue Engineering

  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Torres-Giner, Sergio|||0000-0001-9071-9542
  • Covas, José A.
[EN] In the present study, poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) [P(3HB-co-3HHx)] was reinforced with hydroxyapatite nanoparticles (nHA) to produce novel nanocomposites for potential uses in bone reconstruction. Contents of nHA in the 2.5¿20 wt % range were incorporated into P(3HB-co-3HHx) by melt compounding and the resulting pellets were shaped into parts by injection molding. The addition of nHA improved the mechanical strength and the thermomechanical resistance of the microbial copolyester parts. In particular, the addition of 20 wt % of nHA increased the tensile (Et) and flexural (Ef) moduli by approximately 64% and 61%, respectively. At the highest contents, however, the nanoparticles tended to agglomerate, and the ductility, toughness, and thermal stability of the parts also declined. The P(3HB-co-3HHx) parts filled with nHA contents of up to 10 wt % matched more closely the mechanical properties of the native bone in terms of strength and ductility when compared with metal alloys and other biopolymers used in bone tissue engineering. This fact, in combination with their biocompatibility, enables the development of nanocomposite parts to be applied as low-stress implantable devices that can promote bone reconstruction and be reabsorbed into the human body, L.Q.-C. wants to thank GVA for his FPI grant (ACIF/2016/182) and the Spanish Ministry of Education, Culture, and Sports (MECD) for his FPU grant (FPU15/03812). S.T.-G. acknowledges MICI for his Juan de la Cierva-Incorporacion contract (IJCI-2016-29675). J.I.-M. wants to thank Universitat Politecnica de Valencia for his FPI grant (PAID-2019- SP20190011). Microscopy services of the Universitat Politecnica de Valencia (UPV) are acknowledged for their help in collecting and analyzing the FESEM images. Authors also thank Ercros S.A. for kindly supplying ErcrosBio(R) PH110.