Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 11
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Characterization of a Y-coupler and its impact on the performance of plastic optical fiber links

  • López, A.
  • Losada, M.Á.
  • Mateo, J.
  • Antoniades, N.
  • Jiang, X.
  • Richards, D.
Couplers and splitters are common devices in single-mode and multi-mode glass fibers applications, where they perform a variety of functions. However, when switching to plastic optical fibers (POFs), there is a shortage of commercial devices, which are usually custom-made. The problem with these devices is that modal power distribution in POFs is easily modified by spatial disturbances that produce a localized strong power transfer between modes, thus changing their transmission properties. In this work, a commercial Y-coupler designed for POFs is experimentally characterized. Measurements of its spectral, spatial and temporal characteristics have been performed, including insertion loss as a function of wavelength, angular power distribution, and frequency response. The obtained results show that this device has an equalizing effect over the power spatial distribution that reduces the fiber bandwidth, demonstrating the importance of considering the impact of this type of devices on the transmission properties of any POF system.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Near-infrared supercontinuum source by intracavity silica-based highly-nonlinear fiber

  • López-Ripa, M.
  • Jarabo, S.
  • Salgado-Remacha, F.J.
Near-infrared supercontinuum generation by using silica-based highly-nonlinear fiber placed inside of the ring-cavity of an erbium-doped fiber laser pulsed by mode-locking is experimentally demonstrated. Only one erbium-doped fiber amplifier is employed to generate supercontinuum with a spectral width as long as 830 nm (from 1205 to 2035 nm) and a spectral power higher than -30 dBm/nm. To generate supercontinuum, it is not necessary a second amplifier to raise the power of the laser pulses coupled into the nonlinear fiber. Moreover, all the devices employed are commercial and available at any photonics laboratory. To the best of our knowledge, this is the first demonstration of this kind of device by pumping the nonlinear fiber in the third window of communications.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Real-time 10Gbps Polarization Independent Quasicoherent Receiver for NG-PON2 Access Networks

  • Altabas, J.A.
  • Silva Valdecasa, G.
  • Suhr, L.F.
  • Didriksen, M.
  • Lazaro, J.A.
  • Garces, I.
  • Monroy, T.
  • Clausen, A.T.
  • Jensen, J.
In this paper, we propose and test experimentally a real-time 10 Gbps polarization independent quasicoherent receiver for NG-PON2 access networks. The proposed 10 Gbps quasicoherent receiver exhibits a sensitivity of -35.2 dBm after 40 km SSMF transmission with a commercial generic EML as transmitter. This sensitivity means a 14.9 dB improvement over a direct detection scheme with a photodiode after 40 km SSMF transmission. Therefore, the use of the proposed 10 Gbps quasicoherent receiver with the tested EML will provide a power budget of 34.76 dB (class E1) and a splitting ratio of 128 after the 40 km SSMF transmission. Finally, the proposed 10 Gbps quasicoherent receiver allows a colorless and optical filterless operation because wavelength selection is done by tuning the local oscillator wavelength and using electrical intermediate frequency filtering. IEEE
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Overcoming challenges in large-core SI-POF-based system-level modeling and simulation

  • Richards, Dwight
  • López, Alicia
  • Losada, M. Ángeles
  • Mena, P.V.
  • Ghillino, Enrico
  • Mateo, Javier
  • Antoniades, N.
  • Jiang, Xin
The application areas for plastic optical fibers such as in-building or aircraft networks usually have tight power budgets and require multiple passive components. In addition, advanced modulation formats are being considered for transmission over plastic optical fibers (POFs) to increase spectral efficiency. In this scenario, there is a clear need for a flexible and dynamic system-level simulation framework for POFs that includes models of light propagation in POFs and the components that are needed to evaluate the entire system performance. Until recently, commercial simulation software either was designed specifically for single-mode glass fibers or modeled individual guided modes in multimode fibers with considerable detail, which is not adequate for large-core POFs where there are millions of propagation modes, strong mode coupling and high variability. These are some of the many challenges involved in the modeling and simulation of POF-based systems. Here, we describe how we are addressing these challenges with models based on an intensity-vs-angle representation of the multimode signal rather than one that attempts to model all the modes in the fiber. Furthermore, we present model approaches for the individual components that comprise the POF-based system and how the models have been incorporated into system-level simulations, including the commercial software packages SimulinkTM and ModeSYSTM.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Measurement method of optical properties of ex vivo biological tissues of rats in the near-infrared range

  • Sanchez-Cano, A.
  • Saldaña-Díaz, J.E.
  • Perdices, L.
  • Pinilla, I.
  • Salgado-Remacha, F.J.
  • Jarabo, S.
An optical fiber-based supercontinuum setup and a custom-made spectrophotometer that can measure spectra from 1100 to 2300 nm, are used to describe attenuation properties from different ex vivo rat tissues. Our method is able to differentiate between scattering and absorption coefficients in biological tissues. Theoretical assumptions combined with experimental measurements demonstrate that, in this infrared range, tissue attenuation and absorption can be accurately measured, and scattering can be described as the difference between both magnitudes. Attenuation, absorption, and scattering spectral coefficients of heart, brain, spleen, retina, and kidney are given by applying these theoretical and experimental methods. Light through these tissues is affected by high scattering, resulting in multiple absorption events, and longer wavelengths should be used to obtain lower attenuation values. It can be observed that the absorption coefficient has a similar behavior in the samples under study, with two main zones of absorption due to the water absorption bands at 1450 and 1950 nm, and with different absolute absorption values depending on the constituents of each tissue. The scattering coefficient can be determined, showing slight differences between retina and brain samples, and among heart, spleen and kidney tissues.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Evaluation and measurement of heliostat misalignment in solar power plant using vector model

  • Carretero, E.
  • Preciado, J.
  • Salinas, I.
  • Ayora, I.
  • Heras, C.
Heliostat alignment evaluation is among the main issues in solar tower concentration plant operation and maintenance. This paper describes a novel method used to evaluate heliostat misalignment and its experimental verification. This method provides a different way of visualizing beam centroid pointing errors by generating the complete deviation curve for each axis. This, for example, would be useful for verifying a heliostat’s correct alignment by using a measurement performed out of the receiver target, using these traces to calculate its reflection’s expected location, given a known misalignment. This measurement could be performed during operation simply by including a reflective element in the heliostat and two detector arrays on the tower’s surface. This model has been tested for various types of misalignments of a heliostat at different hours, dates, and heliostat locations. The simulation results have been validated by using an experimental setup at a scale of 1:100.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Amplificador y láser de fibra óptica de sílice dopada con tulio

  • Franco-Rodriguez, Enar
  • Jarabo, Sebastián
  • Salgado-Remacha, Francisco J.
En este trabajo se presenta un láser de fibra dopada con tulio en cavidad de anillo, operando en modo continuo. El bombeo se realiza en la zona de 1600 nm mediante láseres de fibra dopada con erbio. Se ha estudiado el comportamiento con bombeo en modo continuo y en modo pulsado, obteniendo unas eficiencias del 35% y del 38%, respectivamente. Estas eficiencias son superiores a las típicas que se consiguen bombeando en 1600 nm. El láser emite en dos longitudes de onda separadas unos pocos nanómetros, situadas entre 1910 nm y 1920 nm. Al mismo tiempo, se presentan también medidas de ganancia espectral de la fibra dopada con tulio. A modo de ejemplo, se ha realizado un amplificador de fibra dopada con tulio y se ha demostrado su viabilidad amplificando un espectro supercontinuo en la región comprendida entre 1800 nm y 2000 nm, el cual podría utilizarse para bombear fibras no lineales cuya longitud de onda de dispersión cero esté situada en dicha región espectral.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Analysis of Snow Water Equivalent (Swe) of Snowpack by An Ultra Wide Band Step Frequency Continuous Wave Radar (Sfcw)

  • Alonso, R.
  • Garcia del Pozo, J.M.
  • Peruga, I.
  • Buisan, S.
  • Alvarez, J.A.
A ground-based step frequency continuous wave radar (SFCW), based in a software defined radio (SDR), in the range from 150MHz to 6GHz has been designed, fabricated and tested under real conditions. The radar has been applied to measure the snow water equivalent (SWE) of snowpack in the Spanish Pyrenees. A matrix method is applied to solve the electromagnetic reflectance of multilayer cover snow including frequency and wetness dependence of complex relative dielectric permittivity of snow layers. An approximated method to obtain SWE is presented. The method is based on the comparison of measured reflected signal vs distance plot with the calculated with an ''equivalent'' snow layer. Preliminary results are presented and compared with those provided by a cosmic-ray neutron SWE gauge over the 2019 winter. These results suggest the viability of the proposed method.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Analysis of the snow water equivalent at the aemet-formigal field laboratory (Spanish pyrenees) during the 2019/2020 winter season using a stepped-frequency continuous wave radar (SFCW)

  • Alonso, R.
  • García del Pozo, J.M.
  • Buisán, S.T.
  • Álvarez, J.A.
Snow makes a great contribution to the hydrological cycle in cold regions. The parameter to characterize available the water from the snow cover is the well-known snow water equivalent (SWE). This paper presents a near-surface-based radar for determining the SWE from the measured complex spectral reflectance of the snowpack. The method is based in a stepped-frequency continuous wave radar (SFCW), implemented in a coherent software defined radio (SDR), in the range from 150 MHz to 6 GHz. An electromagnetic model to solve the electromagnetic reflectance of a snowpack, including the frequency and wetness dependence of the complex relative dielectric permittivity of snow layers, is shown. Using the previous model, an approximated method to calculate the SWE is proposed. The results are presented and compared with those provided by a cosmic-ray neutron SWE gauge over the 2019–2020 winter in the experimental AEMet Formigal-Sarrios test site. This experimental field is located in the Spanish Pyrenees at an elevation of 1800 m a.s.l. The results suggest the viability of the approximate method. Finally, the feasibility of an auxiliary snow height measurement sensor based on a 120 GHz frequency modulated continuous wave (FMCW) radar sensor, is shown.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Novel measurement-based efficient computational approach to modeling optical power transmission in step-index polymer optical fiber

  • Guerrero, J.
  • Losada, M. A.
  • Lopez, A.
  • Mateo, J.
  • Richards, D.
  • Antoniades, N.
  • Jiang, X.
  • Madamopoulos, N.
Polymer optical fibers (POFs) are playing an important role in industrial applications nowadays due to their ease of handling and resilience to bending and environmental effects. A POF can tolerate a bending radius of less than 20 mm, it can work in environments with temperatures ranging from -55¿ C to +105¿ C, and its lifetime is around 20 years. In this paper, we propose a novel, rigorous, and efficient computational model to estimate the most important parameters that determine the characteristics of light propagation through a step-index polymer optical fiber (SIPOF). The model uses attenuation, diffusion, and mode group delay as functions of the propagation angle to characterize the optical power transmission in the SI-POF. Taking into consideration the mode group delay allows us to generalize the computational model to be applicable to POFs with different index profiles. In particular, we use experimental measurements of spatial distributions and frequency responses to derive accurate parameters for our SI-POF simulation model. The experimental data were measured at different fiber lengths according to the cut-back method. This method consists of taking several measurements such as frequency responses, angular intensity distributions, and optical power measurements over a long length of fiber (>100 m), then cutting back the fiber while maintaining the same launching conditions and repeating the measurements on the shorter lengths of fiber. The model derivation uses an objective function to minimize the differences between the experimental measurements and the simulated results. The use of the matrix exponential method (MEM) to implement the SI-POF model results in a computationally efficient model that is suitable for POF-based system-level studies. The efficiency gain is due to the independence of the calculation time with respect to the fiber length, in contrast to the classic analytical solutions of the time-dependent power flow equation. The robustness of the proposed model is validated by calculating the goodness-of-fit of the model predictions relative to experimental data. © 2022 by the authors. Licensee MDPI, Basel, Switzerland.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Analysis of the Colorless Operation of a Calibrated 120° Coherent Receiver

  • Izquierdo, David
  • Clemente, Jesus
  • Reyes-Iglesias, Pedro
  • Ortega-Monux, Alejandro
  • Altabas, Jose
  • Molina-Fernandez, Inigo
  • Wanguemert-Perez, Juan Gonzalo
  • de Oliva-Rubio, Jose
  • Garces, Ignacio
The performance of an integrated InP 120° coherent receiver has been experimentally analyzed using 50 Gbps 16-QAM signals. IQ components are obtained through a set of coefficients applied to the three output photocurrents of the device. It is demonstrated that the calibration of these coefficients can compensate, without extra computational cost, fabrication hardware impairments and allows a wide optical bandwidth (up to 80 nm range) with a high interfering rejection capability. It has been experimentally verified colorless operation in the complete C-band for a received interfering power close to 11 dB above the signal level. This confirms a remarkable colorless behavior of our proposal.