Skip to main content

DISPOSITIVOS FOTONICOS Y PLASMONICOS: CONTRIBUCION EN NANOMATERIALES, SIMULACION DE DISPOSITIVOS Y MICRO-ESPECTROSCOPIA OPTICA.

TEC2008-06756-C03-03

•
Funding agency name Ministerio de Ciencia e Innovación
Funding agency acronym MICINN
Program Programa Nacional de Proyectos de Investigación Fundamental
Subprogram Subprograma de Proyectos de Investigación Fundamental no Orientada
Call Proyectos I+D
Call year 2008
State Plan 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Management unit Subdirección General de Proyectos de Investigación
Beneficiary centre UNIVERSITAT DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Temperature Sensor Based on Colloidal Quantum Dots PMMA Nanocomposite Waveguides

  • Bueno Martínez, Antonio
  • Suárez Álvarez, Isaac
  • Abargues, Rafael
  • J. MARTÍNEZ-PASTOR
  • Sales Maicas, Salvador|||0000-0001-9457-976X
In this paper, integrated temperature sensors based on active nanocomposite planar waveguides are presented. The nanocomposites consist of cadmium selenide (CdSe) and cadmium telluride (CdTe) quantum dots (QDs) embedded in a polymethylmethacrylate (PMMA) matrix. When the samples are heated in a temperature range from 25$^{circ}{rm C}$ to 50 $^{circ}{rm C}$, the waveguided photoluminescence of QDs suffers from a strong intensity decrease, which is approximately quadratic dependent on temperature. Moreover, the wavelength peak of the waveguided emission spectrum of CdTe-PMMA shows a blue shift of 0.25 ${rm nm}/^{circ}{rm C}$, whereas it remains constant in the case of CdSe-PMMA. A temperature resolution of 0.1$^{circ}{rm C}$ is obtained. QD waveguides have great potential for the development of photonic sensors because of their integration, multiplexing, and roll-to-roll fabrication capabilities., Manuscript received February 21, 2012; revised May 8, 2012; accepted July 18, 2012. Date of publication July 24, 2012; date of current version August 9, 2012. This work was supported in part by the Spanish MICINN and Generalitat Valenciana under Grant TEC-2011-06756-C03-03 and Grant PROMETEO/2009/074, the Plan Nacional I + D under Project TEC2011-29120-C05-01 and Project TEC2011-29120-C05-05, and the Infraestructura FEDER UPVOV08-3E-008. The associate editor coordinating the review of this paper and approving it for publication was Prof. E. H. Yang.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Acoustic cloack for airborne sound by inverse design

  • García Chocano, Víctor Manuel
  • Sanchis, Lorenzo
  • Díaz Rubio, Ana
  • Martínez Pastor, Juan P.
  • Llopis Pontiveros, Rafael
  • Cervera Moreno, Francisco Salvador
  • Sánchez-Dehesa Moreno-Cid, José|||0000-0003-0742-4407
[EN] This Letter presents practical realization of a two-dimensional low loss acoustic cloak for airborne sound obtained by inverse design. The cloak consists of 120 aluminum cylinders of 15 mm diameter surrounding the cloaked object¿a cylinder of diameter 22.5 cm. The position of each cylinder in the cloak is optimized using the data from two different techniques: genetic algorithm and simulated annealing. The operation frequency of this cloak is 3061 Hz with the bandwidth of about 100 Hz. Being a multi-step approach to the desired cloaking, the inverse design is also valid, in principle, for non-symmetric cylinders and even for three-dimensional objects. VC 2011 American Institute of Physics, Work supported by ONR under Award N000140910554 and the Spanish MCINN under Contract Nos. TEC2010-19751, TEC2008-06756-C03-03, and CSD2008-00066 (CONSOLIDER Program). L. S. thanks the fellowship provided by CSIC with number JAEDoc-08-00351.