Skip to main content

DOPADO CON LASER DEL SILICIO CRISTALINO: APLICACION A EMISORES SELECTIVOS Y NUEVAS ESTRUCTURAS DE CELULAS SOLARES

TEC2011-26329

•
Funding agency name Ministerio de Ciencia e Innovación
Funding agency acronym MICINN
Program Programa Nacional de Proyectos de Investigación Fundamental
Subprogram Subprograma de Proyectos de Investigación Fundamental no Orientada
Call Proyectos I+D
Call year 2011
State Plan 2008-2011 Plan Nacional de Investigación Científica, Desarrollo e Innovación Tecnológica
Management unit Subdirección General de Proyectos de Investigación
Beneficiary centre UNIVERSITAT POLITECNICA DE CATALUNYA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

Al2O3/TiO2 inverse opals from electrosprayed self-assembled templates

  • Coll, Arnau
  • Bermejo Broto, Sandra|||0000-0003-1660-0273
  • Hernández, David
  • Castañer Muñoz, Luis María|||0000-0002-1988-6468
The fabrication of high optical quality inverse opals is challenging, requiring large size, three-dimensional ordered layers of high dielectric constant ratio. In this article, alumina/TiO2–air inverse opals with a 98.2% reflectivity peak at 798 nm having an area of 2 cm2 and a thickness of 17 µm are achieved using a sacrificial self-assembled structure of large thickness, which was produced with minimum fabrication errors by means of an electrospray technique. Using alumina as the first supporting layer enables the deposition of TiO2 at a higher temperature, therefore providing better optical quality., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Contribución de congreso (ConferenceOutput)

Improving a nozzle tip with a guard ring for an electrospray system

  • Véliz Noboa, Bremnen Marino
  • Bermejo Broto, Sandra|||0000-0003-1660-0273
  • Castañer Muñoz, Luis María|||0000-0002-1988-6468
The Electrospray technique allows the formation of small droplets from aqueous solutions that may contain nanoparticles of different materials in suspension, leading to the deposition of layers of the nanoparticles. The geometry of the nozzle and the electric field lines from the tip to substrate are key parameters to concentrate the jet of nanodroplets to enhance the deposition control. This work examines the introduction and effect of a guard ring placed at a specific distance from the nozzle. We have been able to make observations with a CCD camera of the fast formation of the Taylor cone with a long elongated jet of deionized water when both the guard ring and substrate are connected to ground. Main results show that the guard ring allows to concentrate the spray jet, reduces the voltage required to shape the cone and reduce the dispersion of the deposit., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publication Artículo científico (JournalArticle)

TCO-free low-temperature p+ emitters for back-junction c-Si solar cells

  • Martín García, Isidro|||0000-0001-8833-9057
  • Coll Valentí, Arnau|||0000-0001-6380-7475
  • López Rodríguez, Gema|||0000-0003-4806-5180
  • Ortega Villasclaras, Pablo Rafael|||0000-0001-6577-614X
  • Desrues, Thibaut
  • Orpella García, Alberto|||0000-0003-2726-5861
  • Alcubilla González, Ramón|||0000-0003-4827-4513
In this work, we report on the fabrication and characterization of n-type c-Si solar cells whose p+ emitters are based on laser processed aluminum oxide/silicon carbide (Al2O3/SiCx) films. The p+ emitter is defined at the rear side of the cell and it consists of point-like laser-diffused p+ regions with a surface charge induced emitter in between based on the high negative charge located at the Al2O3/c-Si interface. These emitters are fabricated at low temperature (< 400 °C) and could be directly compared to silicon heterojunction emitters with the advantage that the deposition of a Transparent Conductive Oxide (TCO) film can be avoided, since they are based on p+/n c-Si homojunctions. Additionally, the involved films are transparent to the IR photons ( >1000 nm) that reach the rear surface of the cell resulting in an excellent back reflector. We fabricated solar cells with distance between p+ regions or pitch ranging from 200 to 350 µm with a front surface based on silicon heterojunction technology. Best efficiency (18.1%) is obtained for a pitch of 250 µm as a consequence of the trade-off between Voc and FF values., Peer Reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publication Contribución de congreso (ConferenceOutput)

Improving a nozzle tip with a guard ring for an electrospray system

  • Véliz Noboa, Bremnen Marino
  • Bermejo Broto, Sandra
  • Castañer Muñoz, Luis María
The Electrospray technique allows the formation of small droplets from aqueous solutions that may contain nanoparticles of different materials in suspension, leading to the deposition of layers of the nanoparticles. The geometry of the nozzle and the electric field lines from the tip to substrate are key parameters to concentrate the jet of nanodroplets to enhance the deposition control. This work examines the introduction and effect of a guard ring placed at a specific distance from the nozzle. We have been able to make observations with a CCD camera of the fast formation of the Taylor cone with a long elongated jet of deionized water when both the guard ring and substrate are connected to ground. Main results show that the guard ring allows to concentrate the spray jet, reduces the voltage required to shape the cone and reduce the dispersion of the deposit., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

TCO-free low-temperature p+ emitters for back-junction c-Si solar cells

  • Martín García, Isidro
  • Coll Valentí, Arnau
  • López Rodríguez, Gema
  • Ortega Villasclaras, Pablo Rafael
  • Desrues, Thibaut
  • Orpella García, Alberto
  • Alcubilla González, Ramón
In this work, we report on the fabrication and characterization of n-type c-Si solar cells whose p+ emitters are based on laser processed aluminum oxide/silicon carbide (Al2O3/SiCx) films. The p+ emitter is defined at the rear side of the cell and it consists of point-like laser-diffused p+ regions with a surface charge induced emitter in between based on the high negative charge located at the Al2O3/c-Si interface. These emitters are fabricated at low temperature (< 400 °C) and could be directly compared to silicon heterojunction emitters with the advantage that the deposition of a Transparent Conductive Oxide (TCO) film can be avoided, since they are based on p+/n c-Si homojunctions. Additionally, the involved films are transparent to the IR photons ( >1000 nm) that reach the rear surface of the cell resulting in an excellent back reflector. We fabricated solar cells with distance between p+ regions or pitch ranging from 200 to 350 µm with a front surface based on silicon heterojunction technology. Best efficiency (18.1%) is obtained for a pitch of 250 µm as a consequence of the trade-off between Voc and FF values., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Al2O3/TiO2 inverse opals from electrosprayed self-assembled templates

  • Coll, Arnau
  • Bermejo Broto, Sandra
  • Hernández, David
  • Castañer Muñoz, Luis María
The fabrication of high optical quality inverse opals is challenging, requiring large size, three-dimensional ordered layers of high dielectric constant ratio. In this article, alumina/TiO2–air inverse opals with a 98.2% reflectivity peak at 798 nm having an area of 2 cm2 and a thickness of 17 µm are achieved using a sacrificial self-assembled structure of large thickness, which was produced with minimum fabrication errors by means of an electrospray technique. Using alumina as the first supporting layer enables the deposition of TiO2 at a higher temperature, therefore providing better optical quality., Peer Reviewed, Postprint (published version)