Skip to main content

TECNOLOGIAS DE RADIODIFUSION DIGITAL EXTRA-TERRESTRES

TEC2014-56483-R

•
Funding agency name Ministerio de Economía y Competitividad
Funding agency acronym MINECO
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2014
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Management unit Secretaría de Estado de Educación, Formación Profesional y Universidades
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Performance evaluation of MIMO channel estimation for ATSC 3.0

  • Shitomi, Takuya
  • Garro, Eduardo
  • Murayama, Kenichi
  • Gomez-Barquero, David|||0000-0003-2610-7765
[EN] ATSC 3.0, the latest Digital Terrestrial Television (DTT) standard, allows a higher spectral efficiency and/or a transmission robustness with Multiple-Input Multiple-Output (MIMO) technology compared to existing single-antenna DTT networks. Regarding MIMO channel estimation, two pilot encoding algorithms known as Walsh-Hadamard encoding and Null pilot encoding are possible in ATSC 3.0. The two MIMO pilot algorithms are standardized so as to have the same pilot positions and the same pilot boosting as SISO, but the performance has not been evaluated. This paper focuses on the performance evaluation of the two MIMO pilot encoding algorithms in ATSC 3.0 using physical layer simulations. Results can be used as guidelines or recommended practices to broadcasters to select the MIMO pilot encoding algorithm that better suits their service requirments. Several channel estimation algorithms have been evaluated in both mobile and fixed reception conditions. The simulation results show that Null pilot encoding provides slightly better performance than WalshHadamard encoding for fixed reception but worse performance for mobile reception, especially at high signal-to-noise ratios., This work was partially supported by the Ministerio de Educacion y Ciencia, Spain (TEC2014-56483-R), co-funded by European FEDER funds.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Information-Theoretic Analysis and Performance Evaluation of Optimal Demappers for Multi-Layer Broadcast Systems

  • Garro, Eduardo
  • Gimenez Gandia, Jordi Joan
  • Klenner, Peter
  • Gomez-Barquero, David|||0000-0003-2610-7765
[EN] Multi-layer broadcast systems distribute services across time and frequency domain by means of power-division multiplexing. Successive interference cancelation is required, in general, in order to extract the content of all services. For a low-complexity implementation, the receiver can obtain the strongest (top-layer) signal assuming underlying signals to behave like thermal noise. The thermal noise assumption may not be valid under certain conditions and a more accurate characterization of the interference could bring improved performance. This paper analyzes the validity of the noise-like assumption considering the power ratio between signals and the required carrier-to-noise ratio for error-free reception. The main contribution of the paper is the proposal of a demapping algorithm that exploits the knowledge of the constellation of underlying signals. Generalized mutual information, performance evaluation, and complexity analysis are provided with the additive white Gaussian noise-like assumptions and with the proposed alternative in order to assess the potential performance improvements that can be achieved., This work was supported by in part by the Ministerio de Educacion y Ciencia, Spain under Grant TEC2014-56483-R, and in part by the European FEDER Funds.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

MIMO Sphere Decoding With Successive Interference Cancellation for Two-Dimensional Non-Uniform Constellations

  • Barjau-Estevan, Carlos Salvador|||0000-0002-4258-6113
  • Gomez-Barquero, David|||0000-0003-2610-7765
  • Fuentes, Manuel
  • Shitomi, Takuya
[EN] Non-uniform constellations (NUCs) have been introduced to improve the performance of quadrature amplitude modulation constellations. 1D-NUCs keep the squared shape, while 2D-NUCs break that constraint to provide robustness. An impending problem with multiple-input multiple-output (MIMO) is the optimum demapping complexity, which grows exponentially with the number of antennas and the constellation order. Some well-known sub-optimum MIMO demappers, such as soft fixed-complexity sphere decoders (SFSD), can reduce that complexity. However, SFSD demappers do not work with the 2D-NUCs, since they perform a quantization step in separated I/Q components. In this letter, we provide an efficient solution for the 2D-NUCs based on Voronoi regions. Both complexity implications and SNR performance are also analyzed., This work was partially supported by the Ministry of Economy and Competitiveness of Spain (TEC2014-56483-R), co-funded by the European FEDER fund.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Wideband Broadcasting: A Power-Efficient Approach to 5G Broadcasting

  • Gimenez Gandia, Jordi Joan
  • Mogarde, Javier
  • Stare, Erik
  • Gomez-Barquero, David|||0000-0003-2610-7765
[EN] Efficient and flexible use of spectrum will be inherent characteristics of fifth-generation (5G) communication technologies with native support of wideband operation with frequency reuse 1, i.e. all transmit sites use all available frequency resources. Although not from the very first 5G release of 3GPP (Third Generation Partnership Project), it is expected that broadcast/multicast technology components will later be added and fully integrated in the 5G system. The combination of both wideband and frequency reuse 1 may provide significant gains for broadcast transmissions in terms of energy efficiency, since it is more efficient to increase capacity by extending the bandwidth rather than increasing the transmit power over a given bandwidth. This breaks with the traditional concept of terrestrial broadcast frequency planning, and paves the way to new potential uses of UHF (Ultra High Frequency) spectrum bands for 5G broadcasting. This paper provides an insight into the fundamental advantages in terms of capacity, coverage as well as power saving of wideband broadcast operation. The role of the network deployment, linked to frequency reuse in the UHF band, and its influence in the performance of a Wideband Broadcasting system are discussed. The technical requirements and features that would enable such power-efficient solution are also addressed., This work was supported in part by the European Commission under the 5G-PPP project 5G-Xcast (H2020-ICT-2016-2 call, grant number 761498). The views expressed in this contribution are those of the authors and do not necessarily represent the project. This work was also partially supported by the Ministerio de Educacion y Ciencia, Spain (TEC2014-56483-R), co-funded by European FEDER funds.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Scattered Pilot Performance and Optimization for ATSC 3.0

  • Garro, Eduardo
  • Gimenez, Jordi Joan
  • Park, Sung Ik
  • Gomez-Barquero, David|||0000-0003-2610-7765
[EN] The next-generation U.S. digital terrestrial television (DTT) standard ATSC 3.0 is the most flexible DTT standard ever developed, outperforming the state-of-the-art digital video broadcasting-terrestrial 2nd generation (DVB-T2) standard. This higher flexibility allows broadcasters to select the configuration that better suits the coverage and capacity requirements per service. Regarding the selection of pilot patterns, whereas DVB-T2 provides eight different patterns with a unique pilot amplitude, ATSC 3.0 expands up to 16, with five different amplitudes per pattern. This paper focuses on the pilot pattern and amplitude performance and optimization for time and power multiplexing modes, time division multiplexing and layered division multiplexing (LDM), respectively, of ATSC 3.0. The selection of the optimum pilot configuration is not straightforward. On the one hand, the pilots must be sufficiently dense to follow channel fluctuations. On the other hand, as long as pilot density is increased, more data overhead is introduced. Moreover, this selection is particularly essential in LDM mode, because the LDM implementation in ATSC 3.0 requires that both layers share all the waveform parameters, including pilot pattern configuration. In addition, there is an error proportional to the channel estimate of the top layer that affects to the lower layer performance., This work was supported in part by the Institute for Information and Communications Technology (IITP) by the Korea Government (MSIP) (Development of Service and Transmission Technology for Convergent Realistic Broadcast) under Grant R0101-15-294, and in part by the Ministerio de Educación y Ciencia, Spain, by European FEDER Funds under Grant TEC2014-56483-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Layered Division Multiplexing with Distributed Multiple-Input Single-Output Schemes

  • Garro, Eduardo
  • Kim, Jeongchang
  • Park, Sung-Ik
  • Hur, Namho
  • Barjau-Estevan, Carlos Salvador|||0000-0002-4258-6113
  • Gomez-Barquero, David|||0000-0003-2610-7765
[EN] Single frequency networks (SFNs) provides an increased spectral efficiency compared to the traditional multiple frequency networks. However, some coverage areas in SFN can be affected by destructive interferences. In order to reduce these situations, distributed multiple-input single-output (MISO) schemes have been adopted in the new digital terrestrial television standards, Alamouti in DVB-T2 and transmit diversity code filter sets in ATSC 3.0. On the other hand, layered division multiplexing (LDM), a non-orthogonal multiple access technology, has been adopted in ATSC 3.0 due to its spectral efficiency increase compared to time or frequency division multiplexing. The LDM signal is formed by a power superposition of two independent signals, which are designed for different reception conditions (mobile and fixed-rooftop). The combination of distributed MISO and LDM techniques has not been evaluated yet. In this paper, the joint transmission of LDM with distributed MISO is analyzed in terms of complexity and the joint performance is evaluated by means of physical layer simulations., This work was supported in part by the ICT Research and Development Program of MSIP/IITP (Development of Transmission Technology for Ultra High Quality UHD) under Grant 2017-0-00081, and in part by the Ministerio de Educacion y Ciencia, Spain, through European FEDER funds under Grant TEC2014-56483-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Optimization and Performance of Non-Uniform Rotated Constellations With Multi-RF Transmission Technique

  • Fuentes Muela, Manuel
  • Giménez Gandia, Jordi Joan
  • Gomez-Barquero, David|||0000-0003-2610-7765
Non-Uniform Constellations (NUC) have been introduced in ATSC 3.0 (Advanced Television Systems Committee - Third Generation) as one of the main novelties to improve the performance compared to uniform Quadrature Amplitude Modulation (QAM) constellations. NUCs are optimized by means of signal geometrical shaping, considering the signal-to-noise ratio (SNR) and the channel model. ATSC 3.0 implements two types of NUC, depending on the number of real-valued dimensions in which they are optimized: 1D-NUC and 2D-NUC. However, the gain of NUCs becomes almost non-existent at high SNRs, especially when optimizing for fading channels. In that particular case, Rotated Constellations (RC) can be used to further improve the overall system performance. RCs may become especially effective when using multi-radio frequency (multi-RF) SNR averaging techniques such as Channel Bonding (CB) or Time-Frequency Slicing (TFS), where in-phase (I) and quadrature (Q) components are transmitted in different RF channels. 2D-NUCs can be rotated without increasing the demapping complexity, since a 2D-demapper is also needed. In this paper, we propose an optimization method designed for rotated 2D-NUCs, in which the rotation angle is considered as an additional variable, together with the symbol positions. The SNR gain obtained in fading channels is also provided for three different use cases: single-RF transmissions, CB with 2 RF channels as adopted in ATSC 3.0, and extension of multi-RF techniques to 4 RF channels., This work was supported by the Ministry of Economy and Competitiveness of Spain, through the European FEDER Fund under Grant TEC2014-56483-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

MIMO Scattered Pilot Performance and Optimization for ATSC 3.0

  • Shitomi, Takuya
  • Garro, Eduardo
  • Murayama, Kenichi
  • Gomez-Barquero, David|||0000-0003-2610-7765
[EN] ATSC 3.0 is the latest digital terrestrial television (DTT) standard, and it allows a higher spectral efficiency and/or a transmission robustness with multiple-input multiple-output (MIMO) technology compared to existing DTT standards. Regarding MIMO channel estimation, two pilot encoding algorithms known as Walsh-Hadamard encoding and Null Pilot encoding are possible in ATSC 3.0. The two MIMO pilot algorithms are standardized so as to have the same pilot positions and the same pilot boosting as single-input single-output, and the optimum pilot configuration has not been fully evaluated for MIMO. This paper focuses on the performance evaluation and optimization of the pilot boosting and the pilot patterns for two MIMO pilot encoding algorithms in ATSC 3.0 using physical layer simulations. This paper provides a great benefit to broadcasters to select the MIMO pilot configuration including pilot boosting, pilot pattern, and pilot encoding algorithm that better suits their service requirements. Several channel interpolation algorithms have been taken into account as a typical receiver implementation in both fixed SFN reception and mobile reception., This work was supported in part by the Ministry of Economy and Competitiveness of Spain under Grant TEC2014-56483-R, and in part by the European FEDER Fund.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Semianalytical Approach to the PDF of SINR in HPHT and LPLT Single-Frequency Networks

  • Gimenez Gandia, Jordi Joan
  • Sung, K. W.
  • Gomez-Barquero, David|||0000-0003-2610-7765
[EN] Single-frequency networks (SFN) are widely adopted in terrestrial broadcast networks based on high-power high-tower (HPHT) deployments. The mobile broadcasting standard Evolved Multimedia Broadcast Multicast Service (eMBMS) has been enhanced in Release 14 to enable SFN operation with larger CP duration which may allow for the deployment of large area SFNs and even the combined operation between HPHT and low-power low-tower (LPLT) cellular stations. The knowledge of the signal-to-interference-plus-noise ratio (SINR) distribution over an SFN area may facilitate the selection of transmission parameters according to the network topology. This paper presents a semianalytical method for the calculation of the SINR distribution in SFNs with low computational complexity compared to Monte Carlo simulations. The method, which builds on previous work developed for cellular communications, is applied to HPHT+LPLT SFNs and evaluated against different transmission and network parameters., This work was supported in part by the Ministerio de Educacion y Ciencia, Spain, under Grant TEC2014-56483-R, in part by European FEDER funds.