Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 18
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Statistical Characterization of Time-Dependent Variability Defects Using the Maximum Current Fluctuation

  • Saraza-Canflanca, P.
  • Martín-Martínez, Javier
  • Castro-López, Rafael
  • Roca, Elisenda
  • Rodríguez, Rosana
  • Fernández, Francisco V.
  • Nafría, Montserrat
This article presents a new methodology to extract, at a given operation condition, the statistical distribution of the number of active defects that contribute to the observed device time-dependent variability, as well as their amplitude distribution. Unlike traditional approaches based on complex and time-consuming individual analysis of thousands of current traces, the proposed approach uses a simpler trace processing, since only the maximum and minimum values of the drain current during a given time interval are needed. Moreover, this extraction method can also estimate defects causing small current shifts, which can be very complex to identify by traditional means. Experimental data in a wide range of gate voltages, from near-threshold up to nominal operation conditions, are analyzed with the proposed methodology., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Circuit reliability prediction: Challenges and solutions for the device time-dependent variability characterization roadblock

  • Nafria, M.
  • Díaz-Fortuny, Javier
  • Saraza-Canflanca, P.
  • Martín-Martínez, Javier
  • Roca, Elisenda
  • Castro-López, Rafael
  • Rodríguez, Rosana
  • Martín-Lloret, P.
  • Toro-Frias, A.
  • Mateo, D.
  • Barajas, Enrique
  • Aragones, X.
  • Fernández, Francisco V.
Copyright IEEE, The characterization of the MOSFET Time-Dependent Variability (TDV) can be a showstopper for reliability-Aware circuit design in advanced CMOS nodes. In this work, a complete MOSFET characterization flow is presented, in the context of a physics-based TDV compact model, that addresses the main TDV characterization challenges for accurate circuit reliability prediction at design time. The pillars of this approach are described and illustrated through examples., This work was supported by the VIGILANT Project (PID2019-103869RB / AEI / 10.13039/501100011033) and the TEC2016-75151-C3-R Project (AEI/FEDER, UE)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

An IC Array for the Statistical Characterization of Time-Dependent Variability of Basic Circuit Blocks

  • Martin-Lloret, P.
  • Núñez, Juan
  • Roca, Elisenda
  • Castro-López, Rafael
  • Martín-Martínez, Javier
  • Rodríguez, Rosana
  • Nafria, M.
  • Fernández, Francisco V.
Talk delivered in International Conference on Synthesis, Modeling, Analysis and Simulation Methods, and Applications to Circuit Design (SMACD) in Lausanne (Switzerland), 15-18 July 2019. © 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., This paper presents an integrated circuit (IC) array whose purpose is to observe, quantify and characterize the impact of time-dependent variability effects, like aging, in several widely used digital and analog circuit blocks. With the increasing interest that this kind of mechanism has attracted in the last years, for its potential impact in the reliability of ultra-scaled integrated circuits, it is only relevant that appropriate measures are taken to find out how it can be included (and thus mitigated) in the design process of such integrated circuits. And, while substantial literature exists that covers the device level, time-dependent variability at circuit level has not been as equally studied. This work complements our previous efforts in providing a holistic approach to Reliability-Aware Design: from statistical characterization and modeling at device-level, to simulation, and into optimization-based design with reliability considerations, the array presented here provides one more step towards a thorough and accurate understanding of how time-dependent variability works at the circuit level., This work was supported in part by the TEC2016-75151-C3-R Project (funded by the Spanish MINECO and ERDF)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

TiDeVa: A Toolbox for the Automated and Robust Analysis of Time-Dependent Variability at Transistor Level

  • Saraza-Canflanca, P.
  • Díaz-Fortuny, Javier
  • Castro-López, Rafael
  • Roca, Elisenda
  • Martín-Martínez, Javier
  • Rodríguez, Rosana
  • Nafria, M.
  • Fernández, Francisco V.
Talk delivered in International Conference on Synthesis, Modeling, Analysis and Simulation Methods, and Applications to Circuit Design (SMACD) in Lausanne (Switzerland), 15-18 July 2019. © 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Time-Dependent Variability has attracted increasing interest in the last years. In particular, time-dependent phenomena such as Bias Temperature Instability, Hot Carrier Injection and Random Telegraph Noise can have a large impact on circuit reliability, and must be therefore characterized and modeled. For technologies in the nanometer range, these phenomena reveal a stochastic behavior and must be characterized in a massive manner, with enormous amounts of data being generated in each measurement. In this work, a novel tool with a user-friendly interface, which allows the robust and fully-automated parameter extraction for RTN, BTI and HCI experiments, is presented., This work has been supported in part by the TEC2016-75151-C3-R Project (funded by the Spanish MINECO and ERDF) and by the P12-TIC-1481 Project (funded by Junta de Andalucía)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Experimental Characterization of Time-Dependent Variability in Ring Oscillators

  • Núñez, Juan
  • Roca, Elisenda
  • Castro-López, Rafael
  • Martín-Martínez, Javier
  • Rodríguez, Rosana
  • Nafria, M.
  • Fernández, Francisco V.
Talk delivered in International Conference on Synthesis, Modeling, Analysis and Simulation Methods, and Applications to Circuit Design (SMACD) in Lausanne (Switzerland), 15-18 July 2019. © 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Reliability in CMOS-based integrated circuits has always been a critical concern. In today's ultra-scaled technologies, a time-varying kind of variability has raised that, on top of the well-known time-zero variability, threatens to shorten the lifetime of integrated circuits, both analog and digital. Effects like Bias Temperature Instability and Hot Carriers Injection need to be studied, characterized and modeled to include, and, thus, mitigate, their impact in the design of CMOS integrated circuits. This paper presents an array-based integrated circuit whose purpose is precisely that: to observe, quantify and characterize the impact of time-dependent variability effects in a specific kind of circuits: Ring Oscillators., This work has been funded by Ministerio de Economía y Competitividad del Gobierno de España with support from ERDF (Projects TEC2016-75151-C3-R, TEC2017-87052-P)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

A New Time Efficient Methodology for the Massive Characterization of RTN in CMOS Devices

  • Pedreira, G.
  • Martín-Martínez, Javier
  • Díaz-Fortuny, Javier
  • Saraza-Canflanca, P.
  • Rodríguez, Rosana
  • Castro-López, Rafael
  • Roca, Elisenda
  • Fernández, Francisco V.
  • Nafria, M.
Talk delivered at the IEEE International Reliability Physics Symposium (IRPS) in Monterrey, California (USA), March 31– April 4, 2019. © 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., In this work a new method to characterize Random Telegraph Noise (RTN) in a large number of devices is presented. The method is applied to the RTN characterization of nearly 800 pMOS transistors and compared with conventional approaches. The results presented here show that the new method, which requires the measurement of each device only in two instants, can hugely reduce the measurement time needed for the statistical characterization of RTN., This work was supported by Spanish AEI and ERDF under Project TEC2016-75151-C3-R. The work of G. Pedreira, J. Diaz-Fortuny and P. Saraza-Canflanca was supported by AEI under grants BES-2017-081462, BES-2014-067855 and BES- 2017-080160 respectively., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Generation of Lifetime-Aware Pareto-Optimal Fronts Using a Stochastic Reliability Simulator

  • Toro-Frias, A.
  • Saraza-Canflanca, P.
  • Passos, Fábio
  • Martin-Lloret, P.
  • Castro-López, Rafael
  • Roca, Elisenda
  • Martín-Martínez, Javier
  • Rodríguez, Rosana
  • Nafria, M.
  • Fernández, Francisco V.
Talk delivered at the 2019 Design, Automation & Test in Europe Conference & Exhibition (DATE) in Florence (Italy), 25 – 29 March 2019. © 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Process variability and time-dependent variability have become major concerns in deeply-scaled technologies. Two of the most important time-dependent variability phenomena are Bias Temperature Instability (BTI) and Hot-Carrier Injection (HCI), which can critically shorten the lifetime of circuits. Both BTI and HCI reveal a discrete and stochastic behavior in the nanometer scale, and, while process variability has been extensively treated, there is a lack of design methodologies that address the joint impact of these two phenomena on circuits. In this work, an automated and time-efficient design methodology that takes into account both process and time-dependent variability is presented. This methodology is based on the utilization of lifetime-aware Pareto-Optimal Fronts (POFs). The POFs are generated with a multi-objective optimization algorithm linked to a stochastic simulator. Both the optimization algorithm and the simulator have been specifically tailored to reduce the computational cost of the accurate evaluation of the impact on a circuit of both sources of variability., This work has been supported by the TEC2016-75151-C3-R Project (funded by the Spanish MINECO and ERDF). Pablo Sarazá Canflanca acknowledges MINECO for supporting his research activity through the predoctoral grant BES-2017-080160., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

New method for the automated massive characterization of Bias Temperature Instability in CMOS transistors

  • Saraza-Canflanca, P.
  • Díaz-Fortuny, Javier
  • Castro-López, Rafael
  • Roca, Elisenda
  • Martín-Martínez, Javier
  • Rodríguez, Rosana
  • Nafria, M.
  • Fernández, Francisco V.
Talk delivered at the 2019 Design, Automation & Test in Europe Conference & Exhibition (DATE), in Florence (Italy), 25 – 29 March 2019. © 2019 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., Bias Temperature Instability has become a critical issue for circuit reliability. This phenomenon has been found to have a stochastic and discrete nature in nanometer-scale CMOS technologies. To account for this random nature, massive experimental characterization is necessary so that the extracted model parameters are accurate enough. However, there is a lack of automated analysis tools for the extraction of the BTI parameters from the extensive amount of generated data in those massive characterization tests. In this paper, a novel algorithm that allows the precise and fully automated parameter extraction from experimental BTI recovery current traces is presented. This algorithm is based on the Maximum Likelihood Estimation principles, and is able to extract, in a robust and exact manner, the threshold voltage shifts and emission times associated to oxide trap emissions during BTI recovery, required to properly model the phenomenon., This work has been supported by the TEC2016-75151-C3-R Projects (funded by the Spanish MINECO and ERDF). Javier Díaz Fortuny acknowledges MINECO for supporting his research activity through the FPI grant BES-2014-067855. Pablo Sarazá Canflanca acknowledges MINECO for supporting his research activity through the predoctoral grant BES-2017-080160., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Improving the reliability of SRAM-based PUFs in the presence of aging

  • Saraza-Canflanca, P.
  • Carrasco-Lopez, H.
  • Brox, Piedad
  • Castro-López, Rafael
  • Roca, Elisenda
  • Fernández, Francisco V.
Talk delivered at the 2020 conference 15th Design & Technology of Integrated Systems in Nanoscale Era (DTIS), Marrakesh (Morocco), April 1-3, 2020. © 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., The utilization of power-up values in SRAM cells for the generation of PUF responses has been widely studied. It is important that the cells used for this purpose are stable, i.e., the cells must have a strong tendency towards one of the two possible values ('0' or '1'). Some methods have been presented that aim at increasing the reliability of this type of PUFs by selecting the strongest cells among a set of them. However, they feature some drawbacks, either in terms of their practical feasibility or of their actual effectiveness selecting the strongest cells in different scenarios. In this work, the experimental results obtained for a new method to classify the cells according to their strength are presented and discussed. The technique overcomes some of the drawbacks that the previous methods present. In particular, it is experimentally demonstrated that the technique presented in this work outstands in selecting SRAM cells that are very robust against circuit degradation, which translates into the construction of reliable SRAM-based PUFs., This work was supported by the TEC2016-75151-C3-R Project (funded by the Spanish MINECO and ERDF). Pablo Sarazá Canflanca acknowledges MINECO for supporting his research activity through the predoctoral grant BES-2017-080160., Peer reviewed
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Aging in CMOS RF linear power amplifiers, an experimental study

  • Nafria, Montserrat|||0000-0002-9549-2890
  • Martin-Martinez, J.|||0000-0001-5938-5898
  • Crespo-Yepes, A.|||0000-0003-4618-651X
  • Rodriguez, R.|||0000-0002-4565-6703
  • Barajas, Enrique|||0000-0002-2072-2268
  • Mateo, Diego|||0000-0001-5996-9092
  • Aragones, Xavier|||0000-0003-1352-8675
An extensive experimental analysis of the HCI and BTI aging effects on RF linear power amplifiers (PA) is presented in this paper. Two different 2.45 GHz PA topologies have been implemented in a CMOS 65 nm technology, one based on a classical common-source (CS) and choke inductor, another one based on a complementary current-reuse (CR) circuit, both of them producing similar gain and output 1-dB compression point (P-1dB). These circuits have been stressed to produce accelerated aging degradation, by applying increasing supply (VDD) voltages, or increasing RF input powers (PIN). The degradation on the transistor parameters (threshold voltage and mobility), DC bias point (IDC current) and RF performance (gain, matching, compression point) have been simultaneously measured. This has allowed to observe how the reduced transistor degradation in CR PA results in a higher robustness in its RF parameters, compared to CS PA circuit. The equivalent RMS voltages have been proposed as an observable metric to assess the combined DC+RF stress in a PA circuit. This has been applied to a semi-analytical model, thus providing comprehension of the link between the conditions under which a circuit is operated, the degradation of the transistor parameters, and the effects on the DC current and RF performance.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Flexible setup for the measurement of CMOS time-dependent variability with array-based integrated circuits

  • Nafria, Montserrat|||0000-0002-9549-2890
  • Martin-Martinez, J.|||0000-0001-5938-5898
  • Rodriguez, R.|||0000-0002-4565-6703
  • Diaz-Fortuny, Javier|||0000-0002-8186-071X
  • Saraza-Canflanca, Pablo|||0000-0003-2155-8305
  • Castro-Lopez, Rafael|||0000-0002-6247-3124
  • Roca, Elisenda|||0000-0001-6260-6495
  • Fernandez, Francisco V.|||0000-0001-8682-2280
This paper presents an innovative and automated measurement setup for the characterization of variability effects in CMOS transistors using array-based integrated circuits (ICs), through which a better understanding of CMOS reliability could be attained. This setup addresses the issues that come with the need for a trustworthy statistical characterization of these effects: testing a very large number of devices accurately but, also, in a timely manner. The setup consists of software and hardware components that provide a user-friendly interface to perform the statistical characterization of CMOS transistors. Five different electrical tests, comprehending time-zero and time-dependent variability effects, can be carried out. Test preparation is, with the described setup, reduced to a few seconds. Moreover, smart parallelization techniques allow reducing the typically time-consuming aging characterization from months to days or even hours. The scope of this paper thus encompasses the methodology and practice of measurement of CMOS time-dependent variability, as well as the development of appropriate measurement systems and components used in efficiently generating and acquiring the necessary electrical signals.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Exploiting the KPFM capabilities to analyze at the nanoscale the impact of electrical stresses on OTFTs properties

  • Ruiz Flores, Ana|||0000-0002-2475-7353
  • Claramunt, Sergi|||0000-0002-2888-7825
  • Crespo-Yepes, A.|||0000-0003-4618-651X
  • Porti i Pujal, Marc|||0000-0001-7438-3823
  • Nafria, Montserrat|||0000-0002-9549-2890
  • Xu, H.
  • Liu, C.
  • Wu, Q.
Two different Kelvin Probe Force Microscopy (KPFM) measurement configurations have been combined to evaluate at the nanoscale the effects of an electrical stress on Organic Thin Film Transistors (OTFTs) properties. As an example, Channel Hot Carrier (CHC) degradation has been induced to provoke some damage in the studied devices. The results show that the use of the two KPFM configurations, together with their nanoscale resolution, provides additional information about the damage in the different regions/materials of the devices, allowing to correlate device level characteristics with the nanoscale material properties.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

A versatile CMOS transistor array IC for the statistical characterization of time-zero variability, RTN, BTI, and HCI

  • Diaz-Fortuny, Javier|||0000-0002-8186-071X
  • Martin-Martinez, J.|||0000-0001-5938-5898
  • Rodriguez, R.|||0000-0002-4565-6703
  • Castro-Lopez, Rafael|||0000-0002-6247-3124
  • Roca, Elisenda|||0000-0001-6260-6495
  • Aragones, Xavier|||0000-0003-1352-8675
  • Barajas, Enrique|||0000-0002-2072-2268
  • Mateo, Diego|||0000-0001-5996-9092
  • Fernandez, Francisco V.|||0000-0001-8682-2280
  • Nafria, Montserrat|||0000-0002-9549-2890
Statistical characterization of CMOS transistor variability phenomena in modern nanometer technologies is key for accurate end-of-life prediction. This paper presents a novel CMOS transistor array chip to statistically characterize the effects of several critical variability sources, such as time-zero variability (TZV), random telegraph noise (RTN), bias temperature instability (BTI), and hot-carrier injection (HCI). The chip integrates 3136 MOS transistors of both pMOS and nMOS types, with eight different sizes. The implemented architecture provides the chip with a high level of versatility, allowing all required tests and attaining the level of accuracy that the characterization of the above-mentioned variability effects requires. Another very important feature of the array is the capability of performing massively parallel aging testing, thus significantly cutting down the time for statistical characterization. The chip has been fabricated in a 1.2-V, 65-nm CMOS technology with a total chip area of 1800 x 1800 mu m(2).
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

A smart noise- and RTN-removal method for parameter extraction of CMOS aging compact models

  • Diaz-Fortuny, Javier|||0000-0002-8186-071X
  • Martin-Martinez, J.|||0000-0001-5938-5898
  • Rodriguez, R.|||0000-0002-4565-6703
  • Castro-Lopez, Rafael|||0000-0002-6247-3124
  • Roca, Elisenda|||0000-0001-6260-6495
  • Fernandez, Francisco V.|||0000-0001-8682-2280
  • Nafria, Montserrat|||0000-0002-9549-2890
In modern nanometer-scale CMOS technologies, time-zero and time-dependent variability (TDV) effects, the latter coming from aging mechanisms like Bias Temperature Instability (BTI), Hot Carrier Injection (HCI) or Random Telegraph Noise (RTN), have re-emerged as a serious threat affecting the performance of analog and digital integrated circuits. Variability induced by the aging phenomena can lead circuits to a progressive malfunction or failure. In order to understand the effects of the mentioned variability sources, a precise and sound statistical characterization and modeling of these effects should be done. Typically, transistor TDV characterization entails long, and typically prohibitive, testing times, as well as huge amounts of data, which are complex to post-process. In order to face these limitations, this work presents a new method to statistically characterize the emission times and threshold voltage shifts (Delta V-th) related to oxide defects in nanometer CMOS transistors during aging tests. At the same time, the aging testing methodology significantly reduces testing times by parallelizing the stress. The method identifies the V-th drops associated to oxide trap emissions during BTI and HCI aging recovery traces while removing RTN and background noise contributions, to avoid artifacts during data analysis.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Statistical threshold voltage shifts caused by BTI and HCI at nominal and accelerated conditions

  • Diaz-Fortuny, Javier|||0000-0002-8186-071X
  • Saraza-Canflanca, Pablo|||0000-0003-2155-8305
  • Rodriguez, R.|||0000-0002-4565-6703
  • Martin-Martinez, J.|||0000-0001-5938-5898
  • Castro-Lopez, Rafael|||0000-0002-6247-3124
  • Roca, Elisenda|||0000-0001-6260-6495
  • Fernandez, Francisco V.|||0000-0001-8682-2280
  • Nafria, Montserrat|||0000-0002-9549-2890
In nowadays deeply scaled CMOS technologies, time-zero and time-dependent variability effects have become important concerns for analog and digital circuit design. For instance, transistor parameter shifts caused by Bias Temperature Instability and Hot-Carrier Injection phenomena can lead to progressive deviations of the circuit performance or even to its catastrophic failure. In this scenario, and to understand the effects of these variability sources, an extensive and accurate device characterization under several test conditions has become an unavoidable step towards trustworthy implementing the stochastic reliability models and simulation tools needed to achieve reliable integrated circuits. In this paper, the statistical distributions of threshold voltage shifts in nanometric CMOS transistors will be studied at nominal and accelerated aging conditions. To this end, a versatile transistor array chip and a flexible measurement setup have been used to reduce the required testing time to attainable values.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Modeling of the degradation of CMOS inverters under pulsed stress conditions from 'on-the-fly' measurements

  • Crespo-Yepes, A.|||0000-0003-4618-651X
  • Ramos, R.
  • Barajas, Enrique|||0000-0002-2072-2268
  • Aragones, Xavier|||0000-0003-1352-8675
  • Mateo, Diego|||0000-0001-5996-9092
  • Martin-Martinez, J.|||0000-0001-5938-5898
  • Rodriguez, R.|||0000-0002-4565-6703
  • Nafria, Montserrat|||0000-0002-9549-2890
In this work, an 'on-the-fly' measurement technique for the monitoring of CMOS inverters performance degradation is presented. This technique allows the characterization of the circuit degradation simultaneously with the applications of the stress. In our experiments, the inversion voltage (V) shifts measured during the application of pulsed voltage stresses at the input. It is demonstrated that the shifts can be described by a power law that accounts for the stress time and voltage dependences. Moreover, the circuit degradation has been correlated to the NMOS and PMOS degradations. The results show that the degradation of the CMOS inverter can be evaluated from an analytical equation that considers only the shifts of two parameters (threshold voltage V, and mobility µ) of the two transistors in the inverter.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Unified RTN and BTI statistical compact modeling from a defect-centric perspective

  • Pedreira Rincon, Gerard|||0000-0002-7792-6501
  • Martin-Martinez, J.|||0000-0001-5938-5898
  • Saraza-Canflanca, Pablo|||0000-0003-2155-8305
  • Castro-Lopez, Rafael|||0000-0002-6247-3124
  • Rodriguez, R.|||0000-0002-4565-6703
  • Roca, Elisenda|||0000-0001-6260-6495
  • Fernandez, Francisco V.|||0000-0001-8682-2280
  • Nafria, Montserrat|||0000-0002-9549-2890
In nowadays deeply scaled CMOS technologies, time-dependent variability effects have become important concerns for analog and digital circuit design. Transistor parameter shifts caused by Bias Temperature Instability and Random Telegraph Noise phenomena can lead to deviations of the circuit performance or even to its fatal failure. In this scenario extensive and accurate device characterization under several test conditions has become an unavoidable step towards trustworthy implementing the stochastic reliability models. In this paper, the statistical distributions of threshold voltage shifts in nanometric CMOS transistors will be studied at near threshold, nominal and accelerated aging conditions. Statistical modelling of RTN and BTI combined effects covering the full voltage range is presented. The results of this work suppose a complete modelling approach of BTI and RTN that can be applied in a wide range of voltages for reliability predictions.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

A Smart Measurement System for the Combined Nanoscale and Device Level Characterization of Electron Devices, Implementation Using Ink-Jet Printing Technologies

  • Claramunt, Sergi|||0000-0002-2888-7825
  • Arrese, Javier|||0000-0003-2743-8013
  • Ruiz Flores, Ana|||0000-0002-2475-7353
  • Porti i Pujal, Marc|||0000-0001-7438-3823
  • Cirera, Albert|||0000-0002-2075-1536
  • Nafria, Montserrat|||0000-0002-9549-2890
In this article, the integration into a single measurement system of device level and nanoscale measurement equipment is presented and applied to the electrical characterization of emerging electron devices. This system is a smart solution to simplify the test procedure, since it allows a fast switching between measurement modes (device or nanoscale level), also featuring an enlarged testing capability. Key in the system is a custom-made inkjet-printed circuit board (I-PCB) that connects the device terminals to the proper instrumentation. The flexibility offered by inkjet-printing technologies is a clear advantage, since many kinds of devices can be tested, without the need of expensive hardware modifications. As a particular case of study, the proposed strategy is demonstrated by implementing a system that alternates between standard electrical measurements with a Semiconductor Parameter Analyzer (SPA) and Conductive Atomic Force Microscopy (CAFM) nanoscale measurements on back-gate graphene field-effect transistors.