Skip to main content

SISTEMA AUTONOMO AIRE/TIERRA DE BAJA ALTURA PARA GEOLOCALIZACION DE INCENDIOS FORESTALES. MODELADO ELECTRO-TERMICO Y DISEÑO DE AMPLIFICADORES DE POTENCIA EFICIENTES.

TEC2017-88242-C3-2-R

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2017
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSIDAD DE VIGO

Resultados relacionados

Resultados totales (Incluyendo duplicados): 12
Encontrada(s) 1 página(s)

Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Artículo científico (JournalArticle)

Dual-Band class J power amplifier at 2.45 and 5.8 GHz for UAVs communications

  • Morales Fernandez, Ainhoa
  • Fernández Barciela, Mónica
  • Isasi De Vicente, Fernando Guillermo
  • Martín Rodríguez, Fernando
  • Tasker, Paul J.
A hybrid dual-band power amplifier (PA) prototype working at two Industrial, Scientific and Medical (ISM) bands, 2.4-2.5 GHz and 5.725-5.875 GHz, was designed for Unmanned Aerial Vehicles (UAVs) communication applications in Spain. Initially, two single-band PA prototypes centered at each band were designed to evaluate the single-band achievable RF performance. In all the PAs, the Gallium Nitride (GaN) Qorvo HEMT TGF2977-SM was used, as well as microstrip transmission lines technology. To achieve wideband, good linearity and efficiency, the PAs were designed in class J. The measured results for the dual-band PA prototype at the 2dB compression point at the lower and higher bands, respectively, are 14.8 dB and 11.2 dB of Transducer Power Gain ( GT ), 35.7 dBm and 34.8 dBm of RF output power (Pout) and 59.2% and 43.5% of Drain Efficiency ( η ). At 3dB compression the respective lower and higher bands results are 37.9 dBm and 37 dBm of Pout and 73.9% and 55% of η ., Agencia Estatal de Investigación | Ref. TEC2017-88242-C3-2-R, Agencia Estatal de Investigación | Ref. PID2020-116569RB-C33
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Contribución de congreso (ConferenceOutput)

GaN-based Class J and Doherty Hybrid Power Amplifiers for C-band communications

  • Aguiar Armada, Diego
  • Morales Fernandez, Ainhoa
  • Fernández Barciela, Mónica
  • Martín Rodríguez, Fernando
  • Isasi De Vicente, Fernando Guillermo
Gallium Nitride (GaN) is nowadays the leading semiconductor technology for the design of transmitters with high RF power at microwave and millimeter wave frequency bands. This paper describes the design, assembly and validation of Class J and Doherty Power Amplifiers (PA) for C-band communications using GaN HEMTs and hybrid technology. The RF performance of each fabricated prototype is assessed and compared to simulations. In simulation, the Class J PA provided at 5.8 GHz 37.3 dBm of RF output power, 14 dB of transducer power gain and 53% of PAE (Power Added Efficiency) at 2 dB compression. The measured RF performance achieved 36 dBm of output power, 12 dB of gain and 47 % of PAE at a slightly lower frequency in C band. On the other hand, the simulated Doherty PA (DPA) achieved at 5.8 GHz a drain efficiency (η) greater than 50% (from 34 to 40 dBm of output power) within the Doherty regime, while providing between 10 and 11.8 dB of gain in the same 6 dB range. The DPA prototype showed lower measured performance than in simulation, providing 9 dB of gain and 39 dBm of maximum output power in C band, Agencia Estatal de Investigación | Ref. TEC2017-88242-C3-2-R, Fondo Europeo de Desarrollo Regional (FEDER), atlanTTic, Agencia Estatal de Investigación | Ref. PID2020-116569RB-C33, info:eu-repo/grantAgreement/AEI/Plan Estatal de Investigación Científica y Técnica y de Innovación 2017-2020/PID2020-116569RB-C33/ES
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Artículo científico (JournalArticle)

Ultra-compact mm-wave monolithic IC doherty power amplifier for mobile handsets

  • Sajedin, Maryam
  • Elfergani, Issa
  • Rodríguez, Jonathan
  • Abd-Alhameed, Raed
  • Fernández Barciela, Mónica
  • Violas, Manuel
This work develops a novel dynamic load modulation Power Amplifier (PA) circuity that can provide an optimum compromise between linearity and efficiency while covering multiple cellular frequency bands. Exploiting monolithic microwave integrated circuits (MMIC) technology, a fully integrated 1W Doherty PA architecture is proposed based on 0.1 μm AlGaAs/InGaAs Depletion-Mode (D-Mode) technology provided by the WIN Semiconductors foundry. The proposed wideband DPA incorporates the harmonic tuning Class-J mode of operation, which aims to engineer the voltage waveform via second harmonic capacitive load termination. Moreover, the applied post-matching technique not only reduces the impedance transformation ratio of the conventional DPA, but also restores its proper load modulation. The simulation results indicate that the monolithic drive load modulation PA at 4 V operation voltage delivers 44% PAE at the maximum output power of 30 dBm at the 1 dB compression point, and 34% power-added efficiency (PAE) at 6 dB power back-off (PBO). A power gain flatness of around 14 ± 0.5 dB was achieved over the frequency band of 23 GHz to 27 GHz. The compact MMIC load modulation technique developed for the 5G mobile handset occupies the die area of 3.2 mm2., Fundação para a Ciência e a Tecnologia | Ref. UIDP/50008/2020, Agencia Estatal de Investigación | Ref. TEC2017-88242-C3-2-R
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Artículo científico (JournalArticle)

A survey on RF and microwave doherty power amplifier for mobile handset applications

  • Sajedin, Maryam
  • Elfergani, I.T.E.
  • Rodríguez, Jonathan
  • Abd-Alhameed, Raed
  • Fernández Barciela, Mónica
This survey addresses the cutting-edge load modulation microwave and radio frequency power amplifiers for next-generation wireless communication standards. The basic operational principle of the Doherty amplifier and its defective behavior that has been originated by transistor characteristics will be presented. Moreover, advance design architectures for enhancing the Doherty power amplifier’s performance in terms of higher efficiency and wider bandwidth characteristics, as well as the compact design techniques of Doherty amplifier that meets the requirements of legacy 5G handset applications, will be discussed., Agencia Estatal de Investigación | Ref. TEC2017-88242-C3-2-R, Fundação para a Ciência e a Tecnologia | Ref. UIDP/50008/2019
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Contribución de congreso (ConferenceOutput)

Design of a wideband harmonically tuned Class-J Power Amplifier

  • Sajedin, Maryam
  • Elfergani, Issa
  • Rodriguez, Jonathan
  • Violas, Manuel
  • Abd-Alhameed, Raed
  • Fernández Barciela, Mónica
  • Abdulkhaleq, Ahmed
This paper describes a modern design idea of wideband and high efficient GaN HEMT Class-J power amplifiers. The operation principle of the Class-J mode, based on the second harmonic tuning, is introduced which can maximize the achievable efficiency. Matching network synthesis criteria for wideband frequency response are addressed for 5G power amplifiers design. This wideband harmonically tuned technique is applicable to amplifiers based on adjusting the shape of the waveforms through a a finite number of harmonics, such as Class-F,F−1 and E. Simulation results indicate that Class-J can provide a high drain efficiency of 70% across a 1.5 to 3.2 GHz bandwidth while delivering 10W output power at the 1dB- compression point, using GaN technology., Agencia Estatal de Investigación | Ref. TEC2017-88242-C3-2-R
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Contribución de congreso (ConferenceOutput)

A compelet design procedure of an X-band MMIC Class-J Power Amplifier

  • Sajedin, Maryam
  • Elfergani, Issa
  • Rodriguez, Jonathan
  • Abd-Alhameed, Raed
  • Fernández Barciela, Mónica
This work presents a complete design process of a high-gain MMIC Class-J power amplifier (PA) based on the 0.25−μm A1GaAs-InGaAs pHEMT technology at X-Band frequencies. The proposed technique can reduce the chip area and improve the energy efficiency. The simulation results indicate that the designed Class-J PA at 6V operation voltage achieves 18dB power gain, 56% PAE and output power of 27.6dBm at 1dB compression. The area size of two-stages PA is 0.9mm2 ., Fundação para a Ciência e a Tecnologia | Ref. UIDB/50008/2020, Fundação para a Ciência e a Tecnologia | Ref. UIDP/50008/2020, Fundação para a Ciência e a Tecnologia | Ref. POCI-01-0145-FEDER-030500, Fundação para a Ciência e a Tecnologia | Ref. ECSEL/0006/2019, Agencia Estatal de Investigación | Ref. TEC2017-88242-C3-2-R
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Artículo científico (JournalArticle)

Multi-resonant Class-F power amplifier design for 5G cellular networks

  • Sajedin, Maryam
  • Elfergani, Issa
  • Rodríguez, Jonathan
  • Violas, Manuel
  • Asharaa, Abdalfettah
  • Abd-Alhameed, Raed
  • Fernández Barciela, Mónica
  • Abdulkhaleq, Ahmed
This work integrates a harmonic tuning mechanism in synergy with the GaN HEMT transistor for 5G mobile transceiver applications. Following a theoretical study on the operational behavior of the Class-F power amplifier (PA), a complete amplifier design procedure is described that includes the proposed Harmonic Control Circuits for the second and third harmonics and optimum loading conditions for phase shifting of the drain current and voltage waveforms. The performance improvement provided by the Class-F configuration is validated by comparing the experimental and simulated results. The designed 10W Class-F PA prototype provides a measured peak drain efficiency of 64.7% at 1dB compression point of the PA at 3.6 GHz frequency., Agencia Estatal de Investigación | Ref. TEC2017-88242-C3-2-R
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Tesis doctoral (DoctoralThesis)

Advancing the extraction and robustness of admittance behavioural models for use in CAD design of nonlinear microwave circuits, Melloras na extracción e robustez de modelos comportamentais de admitancias para o seu uso no deseño CAD de circuitos non lineais de microondas, Mejoras en la extracción y robustez de modelos comportamentales de admitancias para su uso en diseño CAD de circuitos no lineales de microondas

  • Moure Fernández, María del Rocío
The design of nonlinear active analogue circuits for present and future wireless communications systems (WiFi, WiMAX, 5G mobile networks…), is a complex process, since transceiver modules are required to meet strict specs in terms of power, noise, bandwidth, linearity, efficiency and energy consumption, along with reduced weight and size, and the ability to operate with complex signals or multi-band/mode environments. As an example, power amplifier (PA) design using complex configurations, like continuous mode class B/J or Doherty, is nowadays providing very good performance in terms of energy efficiency. But bandwidth improvements in these circuit architectures is not a trivial task. In fact, achieving adequate PA behaviour in wideband usually degrades its performance in comparison with narrowband PAs. Still, continuous class J and wideband Doherty configurations are providing good results. Nevertheless, the design of this type of amplifiers for C- and higher bands is still a challenge. The present nonlinear circuits improved performance is not only the consequence of improvements in the transistor technology and circuit architectures, but also due to new nonlinear vector characterization techniques for active devices. The recent development of nonlinear device behavioural models, which show high accuracy in large signal and excellent computational efficiency in complex circuits, is another important contribution. Among these behavioural models, the X-parameters and the Cardiff model have been successfully used in the design of nonlinear circuits, like PAs, oscillators or mixers. These travelling wave (A-B) formulated behavioural models will be the starting point of this work. This thesis work will focus on the emerging admittance-based (V-I) behavioural formulation. It has been proposed that this modified frequency domain formulation is more appropriate for use in designing state-of-the-art nonlinear circuits where large bandwidth or dual-band requirements are the key drivers. This work will be performed at the University of Vigo (UVigo), initially in the framework of the project titled: “New nonlinear transistor behavioural models and design technologies for dual-band PAs for light weight multicopter drones” (cod. TEC2014-60283C3-3-R), a project in which are involved UVigo, UC y UPGC. The main objective of this thesis work is to advance the understanding of nonlinear behavioural admittance models (defined in the frequency domain) from the perspective of providing an accurate and robust tools for CAD-based design of nonlinear circuits in the microwave band. Aspects, such as, model optimum complexity and fundamental frequency scaling potential will be investigated. Approaches to improve the extraction of these models from load-pull data, and the development of the corresponding nonlinear characterization tools are also undertaken. As part of this work, a large-signal measurement system will be set-up, based on the NVNA PNA-X analyser from Keysight Technologies (available at the AtlantTIC research Center), to perform microwave high power vector calibrated measurements with variable load termination (passive load-pull), up to 25W peak RF power and up to 18GHz. Finally, the transistor characterization methodology and required control of the measurement system software for models extraction and validation will be developed, as well as the routines for model extraction., O deseño de circuítos analóxicos activos non lineais para os sistemas de comunicacións sen fíos presentes e futuros (redes móbiles WiFi, WiMAX, 5G ...) é un proceso complexo, xa que os módulos transceptor deben cumprir unhas especificacións rigorosas en termos de potencia, ruído, anchura de banda, linearidade, eficiencia enerxética e consumo de enerxía, ademais dun peso e tamaño reducidos e a capacidade de operar con sinais complexos ou ambientes multibanda / modo. Como exemplo, o deseño de amplificadores de potencia (PA) a partir de configuracións complexas, como a clase B / J continua ou a configuración Doherty, ofrece actualmente un bo rendemento en termos de eficiencia enerxética. Pero a mellora do ancho de banda destas configuracións non é unha tarefa sinxela. De feito, conseguir un comportamento adecuado do PA ao longo de todo o ancho de banda degrada o seu rendemento en comparación cos PAs de banda estreita. A pesar diso, as configuracións de clase J en modo continuo e banda ancha Doherty ofrecen bos resultados. Non obstante, o deseño destes amplificadores para bandas C e superiores segue sendo un reto. As melloras no rendemento dos circuítos non lineais actuais non son só consecuencia das melloras tecnolóxicas dos transistores e arquitecturas de circuítos, senón tamén polas novas técnicas de caracterización vectorial non lineal de dispositivos activos. Outro importante aporte é o recente desenvolvemento de modelos de comportamento non lineal para estes dispositivos, que mostran alta precisión en gran sinal e unha excelente eficiencia computacional en circuítos complexos. Entre estes modelos de comportamento, os parámetros X e o modelo de Cardiff utilizáronse con éxito no deseño de circuítos non lineais, como PAs, osciladores ou mesturadores. Estes modelos de comportamento formulados por ondas (A-B) serán o punto de partida deste traballo. Este traballo de tese centrarase na formulación comportamental emerxente baseada no dominio de admitancias (V-I). Propúxose que esta formulación modificada no dominio da frecuencia é máis adecuada para o deseño de circuítos non lineais de próxima xeración nos que os requisitos para un gran ancho de banda ou banda dual son os principais motores. Este traballo levarase a cabo na Universidade de Vigo (UVigo), inicialmente no marco do proxecto titulado: " Nuevos modelos no lineales comportamentales de transistores y tecnologías de diseño para amplificadores de potencia de banda dual para drones multicóptero ligeros " (cod. TEC2014- 60283C3-3-R), un proxecto que implica a UVigo, UC e UPGC. O obxectivo principal da tese doutoral é avanzar na comprensión dos modelos comportamentais non lineais de admitancias (definidos no dominio da frecuencia) para que poidan ser unha ferramenta precisa e robusta para o deseño baseado en CAD de circuítos non lineais na banda de microondas. Investigaranse aspectos como a complexidade óptima do modelo e a posibilidade de escalar coa frecuencia fundamental. Tamén se fan melloras na extracción destes modelos a partir de datos de extracción de carga e desenvolvemento das ferramentas de caracterización non lineais correspondentes. Como parte deste traballo, configurarase un gran sistema de medición de sinais, baseado no analizador de redes non lineares de PNA-X Keysight Technologies (dispoñible no Centro de Investigación AtlantTIC), para realizar medicións vectoriais de sinais calibrados con impedancia de carga variable (carga pasiva), ata 25 W de potencia de pico de RF e ata 18GHz. Finalmente, desenvolveranse a metodoloxía de caracterización de transistor e o software de control do sistema de medidas para a extracción e validación de modelos non lineais, así como as rutinas de software para a extracción dos modelos., El diseño de circuitos analógicos activos no lineales para sistemas de comunicaciones inalámbricos presentes y futuros (WiFi, WiMAX, redes móviles 5G...) es un proceso complejo, ya que los módulos transceptores deben cumplir especificaciones estrictas en términos de potencia, ruido, ancho de banda, linealidad, eficiencia energética y consumo de energía, además de un peso y tamaño reducidos, y la capacidad de operar con señales complejas o entornos multibanda / modo. Como ejemplo, el diseño de amplificadores de potencia (PA) a partir de configuraciones complejas, como la clase B/J continuo o la configuración Doherty, ofrece en la actualidad un rendimiento muy bueno en términos de eficiencia energética. Pero las mejoras de ancho de banda de estas configuraciones no es una tarea fácil. De hecho, alcanzar un comportamiento adecuado del PA en todo el ancho de banda generalmente degrada su rendimiento en comparación con los PAs de banda estrecha. A pesar de eso, las configuraciones de clase J en modo continuo y Doherty de banda ancha ofrecen buenos resultados. Sin embargo, el diseño de este tipo de amplificadores para bandas C y superiores sigue siendo un desafío. Las mejoras en las prestaciones de los circuitos no lineales actuales no solo es consecuencia de las mejoras tecnológicas de los transistores y de las arquitecturas de circuitos, sino también por las nuevas técnicas de caracterización vectorial no lineal de dispositivos activos. El desarrollo reciente de modelos no lineales comportamentales para estos dispositivos, que muestran una alta precisión en gran señal y una excelente eficiencia computacional en circuitos complejos, es otra contribución importante. Entre estos modelos de comportamiento, los parámetros X y el modelo de Cardiff se han utilizado con éxito en el diseño de circuitos no lineales, como PAs, osciladores o mezcladores. Estos modelos de comportamiento formulados por ondas (A-B) serán el punto de partida de este trabajo. Este trabajo de tesis se centrará en la formulación comportamental emergente basada en admitancias (V-I). Se ha propuesto que esta formulación modificada en el dominio de la frecuencia es más adecuada para el diseño de circuitos no lineales de última generación donde los requisitos de gran ancho de banda o de banda dual son los impulsores clave. Este trabajo se realizará en la Universidad de Vigo (UVigo), inicialmente en el marco del proyecto titulado: “Nuevos modelos no lineales comportamentales de transistores y tecnologías de diseño para amplificadores de potencia de banda dual para drones multicóptero ligeros” (cod. TEC2014-60283C3- 3-R), un proyecto en el que participan UVigo, UC y UPGC. El objetivo principal de la tesis doctoral es avanzar en la comprensión de los modelos no lineales comportamentales de admitancias (definidos en el dominio de la frecuencia) de forma que puedan ser una herramienta precisa y robusta para el diseño basado en CAD de circuitos no lineales en la banda de microondas. Se investigarán aspectos como la complejidad óptima del modelo y el potencial de escalado con la frecuencia fundamental. También se realizan mejoras en la extracción de estos modelos a partir de datos load-pull, y el desarrollo de las correspondientes herramientas de caracterización no lineales. Como parte de este trabajo, se configurará un sistema de medidas de gran señal, basado en el analizador no lineal de redes PNA-X de Keysight Technologies (disponible en el Centro de Investigación AtlantTIC), para realizar medidas vectoriales calibradas de gran señal con impedancia de carga variable (carga pasiva), hasta 25W de potencia de RF pico y hasta 18GHz. Finalmente, se desarrollará la metodología de caracterización de transistores y el software de control del sistema de medidas para la extracción y validación de los modelos no lineales, así como las rutinas software para la extracción de los modelos., Ministerio de Ciencia e Innovación | Ref. TEC2014-60283-C3-2-R, Agencia Estatal de Investigación | Ref. TEC2017-88242-C3-2-R
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Contribución de congreso (ConferenceOutput)

A systematic investigation of behavioural model complexity requirements

  • Moure Fernández, María del Rocío
  • Casbon, Michael
  • Fernández Barciela, Mónica
  • Tasker, Paul J
In the design of power amplifiers, it is necessary to model the transistor behaviour at high compression levels and accurately predict load-pull power and efficiency contours as well as harmonics. For this purpose, nonlinear behavioural model approaches have been successfully used, like Cardiff model. In this paper, a systematic study is presented on the complexity required for the Cardiff model to achieve a given precision when targeting different load-pull contour design requirements for a GaN HFET. The study has been performed through simulation and measurements and is aimed at providing a systematic approach to aid in the extraction of accurate and efficient Cardiff behavioural models., Ministerio de Economía y Competitividad | Ref. TEC2014-60283-C3-3-R, Agencia Estatal de Investigación | Ref. TEC2017-88242-C3-2-R
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Contribución de congreso (ConferenceOutput)

A systematic investigation of admittance domain behavioral model complexity requirements

  • Moure Fernández, María del Rocío
  • Casbon, Michael
  • Ladero Canle, Nicolás
  • Fernández Barciela, Mónica
  • Tasker, Paul J
Non-linear frequency-domain I-V behavioral models have recently been proposed as an alternative to A-B behavioral models. Admittance formulation is suitable for model scaling with device size and fundamental frequency, very convenient for MMICs CAD. But direct extraction from NVNA measurements, easy to perform with A-B models, is difficult, since we need to account for input variations. Hence determining the required model complexity to aid in the extraction/modelling process becomes a key issue. In this paper, a systematic investigation of the Admittance model complexity requirements to obtain sufficiently accurate model predictions suitable for microwave power amplifier design requirements, is performed., Agencia Estatal de Investigación | Ref. TEC2017-88242-C3-2-R, Ministerio de Economía y Competitividad | Ref. TEC2014-60283-C3-3-R
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Contribución de congreso (ConferenceOutput)

Energy efficient and wideband class-J doherty power amplifier

  • Sajedin, Maryam
  • Elfergani, Issa
  • Rodriguez, Jonathan
  • Abd-Alhameed, Raed
  • Fernández Barciela, Mónica
  • Violas, Manuel
  • Abdulkhaleq, Ahmed
This paper presents a systematic design technique for a wideband GaN HEMT Class-J Doherty amplifier based on the second harmonic tuning. Following a theoretical explore on the expanded design space for a dynamic load modulation, the output matching networks of both Carrier and Peaking amplifiers are synthesized to satisfy the Class-J load requirement. A wideband Class J DPA with a symmetrical architecture is designed as a proof-of-concept to operate over a 1.5 to 3.2 GHz band frequency and delivers 40%-47% power added efficiency., Agencia Estatal de Investigación | Ref. TEC2017-88242-C3-2-R
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Artículo científico (JournalArticle)

Evaluation of admittance domain behavioural model complexity requirements for Power Amplifier design

  • Moure Fernández, María del Rocío
  • Casbon, Michael
  • Ladero Canle, Nicolás
  • Fernández Barciela, Mónica
  • Tasker, Paul J.
In the framework of Power Amplifier (PA) design for communications, frequency domain non-linear behavioural models have shown their potential as efficient complementary modelling tools when Field Effect Transistor compact models are not available or sufficiently accurate. The Admittance behavioural model, formulated in the V-I domain, is especially suitable for device size and fundamental frequency scaling. It is important to note that the direct extraction of this model, from the Nonlinear Vector Network Analyser (NVNA) load-pull (LP) measurements, requires some extra processing since it necessitates a Look-up-Table indexed to |V11| rather than |A11|. When using such models in PA design, there is the need for the user to select the necessary model complexity. To address this requirement, in this paper, a systematic analysis methodology, to guide the user, is presented and validated in different PA design scenarios. The methodology was tested using NVNA LP measurements of GaN Heterostructure FETs. A fifth order Admittance model formulation showed good accuracy in the studied PA design scenarios., Agencia Estatal de Investigación | Ref. TEC2017‐88242‐C3‐2‐R, Xunta de Galicia and European Regional Development Fund - ERDF| Ref. "Centro singular de investigación de Galicia accreditation 2019-2022, atlanTTic", Agencia Estatal de Investigación | Ref. PID2020-116569RB-C33