Skip to main content

DESARROLLO DE NUEVAS TECNICAS DE LIMITACION DE LA PERDIDA DE PRESION EN DPFS PARA REDUCIR LAS EMISIONES Y EL CONSUMO DE LOS MOTORES DIESEL

TRA2013-40853-R

•
Funding agency name Ministerio de Economía y Competitividad
Funding agency acronym MINECO
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2013
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Management unit Secretaría de Estado de Educación, Formación Profesional y Universidades
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 15
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

In-cylinder pressure based model for exhaust temperature estimation in internal combustion engines

  • Guardiola, Carlos|||0000-0002-3150-8566
  • Olmeda, P.|||0000-0002-3161-0165
  • Pla Moreno, Benjamín|||0000-0001-9238-2939
  • Bares-Moreno, Pau|||0000-0001-9672-0819
[EN] Exhaust temperature is a valuable parameter for engine control. However, measurement conditions at the engine exhaust and the slow dynamic response of temperature sensors difficult the determination of the instantaneous exhaust temperature. The present paper proposes a methodology for estimating the exhaust temperature exclusively relying in-cylinder pressure signal, engine speed and exhaust lambda.The presented methodology can replace or actualize widespread look-up table models for correcting calibration offsets, due to ageing, sensor bias or disturbances associated with the engine operation. The method uses the existence of resonant modes in the in-cylinder pressure for inferring the trapped mass and the in-cylinder temperature. An isentropic expansion of the gasses through the valves is assumed for estimating the cylinder outlet temperature of the gases, and the gas temperature drop along the exhaust runner and manifold is modelled through a nodal thermal model. The method was compared with current models under steady and transient conditions in a four stroke CI engine. Variations of injection, EGR, intake pressure and rail pressure were performed under steady operation and the transient response of the method was validated under specific transient test and at the WLTP cycle. A time invariant first order model was used for comparing the estimated temperature with that provided by the experimental sensors. (C) 2016 Elsevier Ltd. All rights reserved., This research has been partially financed by the Spanish Ministerio de Economia Competitividad, through project TRA2013-40853-R "Desarrollo de nuevas tecnicas de limitation de la perdida de presion en DPFs para reducir las emisiones y el consumo de los motores diesel (PRELIMIT)".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of the influence of pre-DPF water injection technique on pollutants emission

  • Bermúdez, Vicente|||0000-0002-2781-5598
  • Serrano, J.R.|||0000-0003-0692-3917
  • Piqueras, P.|||0000-0002-3767-0839
  • Campos, Daniel
The pressure drop across DPFs directly affects the exhaust back-pressure and fuel economy of compression ignition engines. Pressure drop is related to the soot trapped inside the DPF, increasing exhaust back-pressure as the soot mass loading does. Consequently, regeneration strategies are required to remove the soot collected in the DPF. However, these processes usually involve additional fuel consumption. Considering this context, control techniques to reduce the exhaust back-pressure dependence on DPF soot loading are arising. One technique is based on the pre-DPF water injection events to get an optimum redistribution of the soot layer leading to a reduction of DPF pressure drop. This paper is focused to establish a comprehensive analysis of the change in pollutants emitted due to this technique application. The effects of this technique on filtration efficiency and particle size distribution are also analysed during and after a DPF loading test. Results have shown a dilution effect on gaseous compounds and a negligible particle emission during the pre-DPF water injection event (<2 mg), increasing PSD mode downstream the DPF to the mode of the raw emission. Nevertheless, there are not relevant effects on overall filtration efficiency, which keeps value comparable to baseline operation clearly higher than 99%., This work has been partially supported by Government of Spain through grant number FEDER-ICTS-2012-06, framed in the operational program of unique scientific and technical infrastructure of the Ministry of Science and Innovation, and through grant number TRA2013-40853-R of the Ministry of Economy and Competitiveness.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Radial turbine performance measurement under extreme off-design Conditions

  • Serrano, J.R.|||0000-0003-0692-3917
  • Tiseira, Andrés-Omar|||0000-0001-9472-2386
  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
  • Inhestern, Lukas Benjamin
  • Tartoussi, H.
[EN] During automotive urban driving conditions and future homologation cycles, automotive radial turbines experience transient conditions, whereby the same operate at very high blade speed ratios and, thus, at very low power outputs. Under those conditions, the turbine power output might not be enough to feed the mechanical power needs of the compressor. Typical fast one-dimensional full engine simulations rely on steady-state performance maps to characterize the turbocharger. Due to the restricting compressor braking power, extreme off-design measurements cannot be obtained in standard gas stands without using an external brake instead of the compressor or without using a motor attached to the turbocharger shaft. Such turbocharger assemblies cause shaft balancing issues inherent to the connection to a brake operating at high rotational speeds or need basic changes of the turbocharger geometry. This paper presents a novel approach for turbine performance map measurements at very low expansion ratio and very low mass flow without the aforementioned issues. The method uses the turbocharger compressor as a centrifugal turbine, providing mechanical power to the shaft and enabling turbine performance measurements from points of very high expansion ratio up to very low pressure ratio. It is even possible to measure at almost zero flow rate in the turbine when it consumes shaft power instead of producing it. This experimental procedure that can be applied to whatever turbocharger produces valuable information for the development and validation of turbine performance models aiming to extrapolate its behaviour at off-design conditions., The authors of this paper wish to thank M.A. Ortiz for his invaluable help during the experimental setup. The work has been partially supported by the Spanish Ministry of Economy and Competitiveness through grant number TRA2013-40853-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

General Procedure for the Determination of Heat Transfer Properties in Small Automotive Turbochargers

  • Serrano, J.R.|||0000-0003-0692-3917
  • Olmeda, P.|||0000-0002-3161-0165
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Dombrovsky, Artem
These days many research efforts on internal combustion engines are centred on optimising turbocharger matching and performance on the engine. In the last years a number of studies have pointed out the strong effect on turbocharger behaviour of heat transfer phenomena. The main difficulty for taking into account these phenomena comes from the little information provided by turbocharger manufacturers. In this background, Original Engine Manufacturers (OEM) need general engineering tools able to provide reasonably precise results in predicting the mentioned heat transfer phenomena. Therefore, the purpose of this work is to provide a procedure, applicable to small automotive turbochargers, able to predict the heat transfer characteristics that can be used in a lumped 1D turbocharger heat transfer model. This model must be suitable to work coupled to whole-engine simulation codes (such as GT-Power or Ricardo WAVE) for being used in global engine models by the OEM. Moreover, the procedure must be capable to predict heat transfer effects using available data as external geometrical parameters of the turbocharger. To reach these several purposes, a description of the procedure to obtain correlations for heat transfer behaviour to be used in a lumped model is given. The procedure is based on several generalised correlations obtained from the evaluation of heat transfer properties of different turbochargers. The validity of the procedure is confirmed by simulations performed in GT-Power environment compared to experimental results both in a gas stand and in an engine test bench. The results of the validation show an acceptable level of accuracy using the proposed procedure. Furthermore, the advantages of the procedure are shown by comparing its results with the results of standard GT-Power simulations. In these last simulations only turbocharger maps are used without a turbocharger heat transfer model. Further analysis of these results evidences that the simple procedure of using general correlations for heat transfer properties in a lumped model is accurate enough to predict turbine outlet temperature much better than standard GTPower model. This parameter is crucial for after treatment modelling and design as well as for two stage turbocharging., The work has been partially supported by Ministerio de Economia y Competitividad, Secretaria de Estado de Investigacion. Subdireccion de proyectos de investigacion (TRA2013-40853-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Pre-DPF water injection technique for pressure drop control in loaded wall-flow diesel particulate filters

  • Bermúdez, Vicente|||0000-0002-2781-5598
  • Serrano, J.R.|||0000-0003-0692-3917
  • Piqueras, P.|||0000-0002-3767-0839
  • García Afonso, Óscar
Wall-flow type diesel particulate filter (DPF) is a required aftertreatment system for particle emission abatement and standards fulfilment in Diesel engines. However, the DPF use involves an important flow restriction, especially as the substrate gets soot and ash loaded. It gives as a result the increase of the exhaust back-pressure and hence a fuel consumption penalty. The increasing damage of fuel consumption with DPF soot loading leads to the need of the regeneration process. Usually based on active strategies, this process involves an additional fuel penalty but prevents from excessive DPF pressure drop and ensures secure soot burnt out. Under this context, new solutions are required to improve the state of the art DPF soot loading to pressure drop ratio. This paper presents a novel technique based on pre-DPF water injection to reduce the DPF pressure drop under soot loading conditions by disrupting its dependence on soot/ash loading. It provides benefits to engine fuel economy and also higher flexibility for DPF regeneration and maintenance. The work covers a test campaign performed in a passenger car turbocharged Diesel engine equipped with a wall-flow DPF. The main objective is to describe the technique, to provide a figure of its potential for pressure drop control and fuel consumption reduction. The results of the experiments also confirm soot and ash loading capacity increase and demonstrate the lack of negative effects on filtration efficiency and active and passive regeneration., This work has been partially supported by the Spanish Ministry of Economy and Competitiveness through Grant No. TRA2013-40853-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Phenomenological methodology for assessing the influence of flow conditions on the acoustic response of exhaust aftertreatment systems

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Piqueras, P.|||0000-0002-3767-0839
  • Sanchis, Enrique José|||0000-0002-6856-8992
  • Tartoussi, H.
[EN] The increasing limits of standards on aerosol and gaseous emissions from internal combustion engines have led to the progressive inclusion of different exhaust aftertreatment systems (EATS) as a part of the powertrain. Regulated emissions are generally abated making use of devices based on monolithic structures with different chemical functions. As a side effect, wave transmission across the device is affected and so is the boundary at the exhaust line inlet, so that the design of the latter is in turn affected. While some models are available for the prediction of these effects, the geometrical complexity of many devices makes still necessary in many cases to rely on experimental measurements, which cannot cover all the diversity of flow conditions under which these devices operate. To overcome this limitation, a phenomenological methodology is proposed in this work that allows for the sound extrapolation of experimental results to flow conditions different from those used in the measurements. The transfer matrix is obtained from tests in an impulse rig for different excitation amplitudes and mean flows. The experimental coefficients of the transmission matrix of the device are fitted to Fourier series. It allows treating the influence of the flow conditions on the acoustic response, which is manifested on changes in the characteristic periods, separately from the specific properties of every device. In order to provide predictive capabilities to the method, the Fourier series approach is coupled to a gas dynamics model able to account for the sensitivity of propagation velocity to variations in the flow conditions. (C) 2017 Elsevier Ltd. All rights reserved., This work has been partially supported by the Spanish Ministerio de Economia y Competitividad through Grant no. TRA2013-40853-R. Additionally, the Ph.D. student E.J. Sanchis has been funded by a grant from Universitat Politecnica de Valencia with reference FPI-2016-S2-1355. These supports are gratefully acknowledged by the authors. Finally, the authors wish also to acknowledge the suggestions of the referees, which have resulted in a considerable improvement of the text.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Model-based passive and active diagnostics strategies for diesel oxidation catalyst

  • Guardiola, Carlos|||0000-0002-3150-8566
  • Pla Moreno, Benjamín|||0000-0001-9238-2939
  • Piqueras, P.|||0000-0002-3767-0839
  • Mora-Pérez, Javier
  • Lefebvre, D.
[EN] This article proposes a diesel oxidation catalyst diagnostics strategy based on the exothermic process generated by exhaust gas species oxidation in the catalyst. The diagnostics strategy is designed to be applied on-board and respecting real-time electronic control unit computational limitations. Diagnostics purposes are fulfilled by means of the comparison of the passive model temperature, which represents the outlet temperature of a non-impregnated diesel oxidation catalyst, and the measurement provided by the on-board catalyst-out temperature sensor. Thus, the presented diagnostics strategy uses only two production grade temperature sensors and the measurements of air and fuel mass flows from the electronic control unit. Passive diagnostics is based on the oxidation of engine-raw emissions, whilst active diagnostics is based on the oxidation of requested post injected fuel. Post-injection strategy is also discussed for active diagnosis. Then, the diagnostics strategy is able to discern whether the diesel oxidation catalyst is able to oxidise or not. (C) 2016 Elsevier Ltd. All rights reserved., This research has been partially financed by the Spanish Ministerio de Economia y Competitividad, through project TRA2013-40853-R 'Desarrollo de nuevas tecnicas de limitacion de la perdida de presion en DPFs para reducir las emisiones y el consumo de los motores diesel (PRELIMIT)'.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental and computational approach to the transient behaviour of wall-flow diesel particulate filters

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Serrano, J.R.|||0000-0003-0692-3917
  • Piqueras, P.|||0000-0002-3767-0839
  • García Afonso, Óscar
[EN] The implementation of tight vehicle emission standards has forced manufactures to use aftertreatment systems extensively. In addition to pollutant emissions abatement, these devices have a noticeable impact on the wave pattern. This fact affects the muffler design criteria. All monolithic aftertreatment devices produces a damping effect because of the honeycomb structure and the narrow channels. However, this response is more marked in wall-flow diesel particulate filters (DPF) because of the alternatively plugged ends and the dissipative properties of the porous substrate. The main goal of this paper is to assess the transient fluid-dynamic behaviour of wall-flow DPFs using experimental and modelling techniques. The experimental data were gathered in clean and loaded conditions. The DPF was subjected to a variety of pressure excitations to characterise its transient behaviour in the time and frequency domains. Afterwards, the DPF response was evaluated under engine-like operating conditions in an unsteady flow gas stand. Once the main characteristics of the response were known, a non-linear gas-dynamics model was proposed for analysis and prediction. The model accounts for space and time gradients, combining the thermo-and fluid-dynamic solution with a model based on a packed bed of spherical particles that defines the meso-structure of the loaded substrate. (C) 2016 Elsevier Ltd. All rights reserved., This work has been partially supported by the Spanish Ministerio de Economia y Competitividad through Grant No. TRA2013-40853-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of fluid-dynamic guidelines in diesel particulate filter sizing for fuel consumption reduction in post-turbo and pre-turbo placement

  • Serrano, J.R.|||0000-0003-0692-3917
  • Climent, H.|||0000-0002-2407-5651
  • Piqueras, P.|||0000-0002-3767-0839
  • Angiolini, Emanuele
Wall-flow particulate filters are in the present days a standard aftertreatment system widely used in diesel engines to reduce particle emissions and meet emission regulations. This paper deals with the analysis of the macro- and meso-geometry definition of the DPF monoliths from a fluid-dynamic modelling approach. Focus is driven to the analysis of the influence on pressure drop and hence on engine fuel economy. The influence of the DPF volume on the engine performance is analysed with a gas dynamic software including both post-turbo and pre-turbo placement under clean and soot loading conditions. A swept in cell density is also considered for different thermal integrity factors. This approach allows analysing the trends in pressure drop and cell unit geometric parameters defining the monolith thermal and mechanical performance. A discussion considering constant specific filtration area and constant filtration area is performed providing a comprehensive understanding of the DPF and engine response as volume and cellular geometry are changed. Results are leading to rigorously justify known but usually empirical guidelines for DPF design in post-turbo applications. A discussion on the potential for monolith volume reduction in pre-turbo applications with respect to the post-turbo baseline is addressed. This is based on the very low sensitivity of fuel consumption and pressure drop both to volume reduction and soot and ash loading with pre-turbo DPF configuration, This work has been partially supported by the Spanish Ministry of Economy and Competitiveness through Grant No. TRA2013-40853-R. Additionally, the Ph.D. student E. Angiolini has been funded by a grant from Conselleria de Educacio, Cultura i Esport of the Generalitat Valenciana with reference GRISOLIA/2013/036. These supports are gratefully acknowledged by the authors.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Adaptation of a 1-D tool to study transient thermal in turbocharger bearing housing

  • Serrano, J.R.|||0000-0003-0692-3917
  • Tiseira, Andrés-Omar|||0000-0001-9472-2386
  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
  • Rodriguez-Usaquen, Yuly Tatiana
[EN] The heat transfer model can be used in a one-dimensional (1-D) engine simulation. When the engine speed is reduced to zero, the codes have been upgraded to calculate transient turbocharger thermal conditions. The turbocharger model has been used as an external plugin. Analysis of the temperature evolution at different parts of the turbocharger is done by using a hot spot engine cycle. A turbocharger bypassing strategy is done by means of a 9 bypass valve system. By using this method, instabilities can be found in the binary on-off state of an engine. During engine hot-stops, the lack of oil flow inside the turbocharger makes the trapped oil in the bearings burnt as the turbine housing exchanges heat with the central housing. Coke formation can appear and produce big reductions in turbocharger endurance, as bearings clogged and damage the shaft. Several strategies can be used in order to minimize possibilities of coke formation, including an increase in the turbocharger cooling during normal operation and the use of electrically-driven pumps acting after the engine is shut down. These strategies can be simulated in acceptable calculation times thanks to modelling strategy proposed in this paper. The presented methodology allows a detailed study of the temperature rise of the central housing of an automotive turbocharger after a hot-stop process, simulating several combinations of cooling strategies in order to find the optimum one in terms of minimising extra energy consumption per K of housing temperature reduction., We thank Przemek Kmiec for his support in the language editing. This work has been partially supported by the Spanish Ministry of Economyand Competitiveness through [grant No. TRA2013-40853-R].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Fast estimation of diesel oxidation catalysts inlet gas temperature

  • Guardiola, Carlos|||0000-0002-3150-8566
  • Dolz-García, Vicente Manuel
  • Pla Moreno, Benjamín|||0000-0001-9238-2939
  • Mora-Pérez, Javier
With the tightening of on-board diagnostics requirements, accuracy of sensors is essential to monitor the efficiency and ensure a proper control of the after-treatment systems. Temperature sensors are commonly used in the exhaust line at the diesel oxidation catalyst-inlet of turbocharged diesel engines for control and diagnosis of the after-treatment system. In particular, negative temperature constant sensors are used for this purpose. However, due to the necessary robustness that on-board sensors must fulfil, thermal inertia causes significant differences during engine transient operating conditions in temperature measurements. A Kalman filter is proposed in this paper for the on-line dynamic estimation of the catalyst-inlet temperature, which combines a slow but accurate measurement of the on-board temperature sensor with a fast but drifted temperature model. A fast research-grade thermocouple is used as reference of the actual exhaust gas temperature as well as a frequency analysis is performed in order to calibrate the model and analyse results of the signal reconstruction. Results of the algorithm are then successfully proved in experimental transient tests and typical European approval test cycles, This research has been partially financed by the Spanish Ministerio de Economia y Competitividad, through project TRA2013-40853-R PRELIMIT.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development and validation of a radial turbine efficiency and mass flow model at design and off-design conditions

  • Serrano, J.R.|||0000-0003-0692-3917
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
  • Dombrovsky, Artem
  • Tartoussi, H.
Turbine performance at extreme off-design conditions is growing in importance for properly computing turbocharged reciprocating internal combustion engines behaviour during urban driving conditions at current and future homologation cycles. In these cases, the turbine operates at very low flow rates and power outputs and at very high blade to jet speed ratios during transitory periods due to turbocharger wheel inertia and the high pulsation level of engine exhaust flow. This paper presents a physically based method that is able to extrapolate radial turbines reduced mass flow and adiabatic efficiency in blade speed ratio, turbine rotational speed and stator vanes position. The model uses a very narrow range of experimental data from turbine maps to fit the necessary coefficients. By using a special experimental turbocharger gas stand, experimental data have been obtained for extremely low turbine power outputs for the sake of model validation. Even if the data used for fitting only covers the turbine normal operation zone, the extrapolation model provides very good agreement with the experiments at very high blade speed ratio points; producing also good results when extrapolating in rotational speed and stator vanes position., The authors of this paper wish to thank M.A. Ortiz for his invaluable help during the experimental setup and to Arnau Blasco for his hard data fitting work. This work has been partially supported by the Spanish Ministry of Economy and Competitiveness through Grant No. TRA2013-40853-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Filtration modelling in wall-flow particulate filters of low soot penetration thickness

  • Serrano, J.R.|||0000-0003-0692-3917
  • Climent, H.|||0000-0002-2407-5651
  • Piqueras, P.|||0000-0002-3767-0839
  • Angiolini, Emanuele
A filtration model for wall-flow particulate filters based on the theory of packed beds of spherical particles is presented to diagnose the combined response of filtration efficiency and pressure drop from a reliable computation of the flow field and the porous media properties. The model takes as main assumption the experimentally well-known low soot penetration thickness inside the porous wall. The analysis of soot loading processes in different particulate filters shows the ability of the proposed approach to predict the filtration efficiency as a function of the particle size distribution. Nevertheless, pressure drop and overall filtration efficiency are determined by the mode diameter of the raw particulate matter emission. The results reveal the dependence of the filtration efficiency in clean conditions on the sticking coefficient. However, the dynamics of the pressure drop and filtration efficiency as the soot loading varies is governed by the soot penetration thickness. This parameter is closely related to the porous wall Peclet number, which accounts for the porous wall and flow properties influence on the deposition process. The effect of the transition from deep bed to cake filtration regime on the pressure drop is also discussed underlying the importance of the macroscale over microscale phenomena., This work has been partially supported by the Spanish Ministry of Economy and Competitiveness through Grant No. TRA2013-40853-R. Additionally, the Ph.D. student E. Angiolini has been funded by a grant from Conselleria de Educacio, Cultura i Esport of the Generalitat Valenciana with reference GRISOLIA/2013/036. These supports are gratefully acknowledged by the authors.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Turbocharger heat transfer and mechanical losses influence in predicting engines performance by using one-dimensional simulation codes

  • Serrano, J.R.|||0000-0003-0692-3917
  • Olmeda, P.|||0000-0002-3161-0165
  • Arnau Martínez, Francisco José|||0000-0003-2902-0630
  • Dombrovsky, Artem
  • Smith, Les
The exhaust energy can represent up to 40% of the fuel chemical energy in turbocharged internal combustion engines. In order to calculate properly the available energy of the exhaust gases, a critical parameter is the temperature downstream the turbine. The prediction of this temperature will also benefit the two-stage turbochargers and after-treatment modelling that affects brake specific fuel consumption, exhaust gases emissions and the scavenging process. In this paper, turbocharger heat transfer losses have been modelled using a lumped capacitance model coupled with one-dimensional whole-engine simulation software. The data from the simulations of a turbocharged Diesel engine, with and without the turbocharger heat transfer model, have been compared with experimental measurements performed in an engine test bench. The analysis is focused on studying the influence in turbocharger outlet temperatures and predicting the engine performance. The main result of the study is the improvement in the prediction of both compressor and turbine outlet temperatures (up to an improvement of 70 K). The results from the model allow analysing how heat transfer losses are split in the turbocharger and quantifying the importance of heat transfer phenomena in turbocharger efficiency, at full load conditions and as a function of engine speed., This work has been financial supported by Jaguar Land Rover Ltd. It has been also partially supported by Ministerio de Economia y Competitividad, Secretaria de Estado de Investigacion, Subdireccion de proyectos de investigacion (TRA2013-40853-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental assessment of a pre-turbo aftertreatment configuration in a single stage turbocharged diesel engine. Part 2: Transient operation

  • Luján, José M.|||0000-0001-6133-8943
  • Serrano, J.R.|||0000-0003-0692-3917
  • Piqueras, P.|||0000-0002-3767-0839
  • García Afonso, Óscar
This paper corresponds to the second part of a work devoted to analyse the impact of the pre-turbo aftertreatment configuration on the performance of a single stage turbocharged Diesel engine. This second part focuses on the analysis of the engine response under transient operating conditions. To address the causes and effects of the change in engine response several types of transient processes consisting of driving cycles and load transient tests have been evaluated as starting point of the analysis. These tests make possible to account for the influence of the aftertreatment thermal inertia and how it affects the engine and aftertreatment performance obtained during driving cycles and under highly demanding transient operation. The pre-turbo aftertreatment placement also provides advantages in terms of faster aftertreatment warm-up. Therefore, the benefits on DPF (diesel particulate filter) passive regeneration as well as DOC (diesel oxidation catalyst) light-off leading to lower gas emissions have been assessed. The results have been compared against baseline emissions measured during experiments with post-turbo aftertreatment placement. Finally the influence of the thermal inertia on driveability in sudden accelerations as a function of the wall temperature along the exhaust line and boosting architecture is assessed combining the analysis of experimental and modelled data., This work has been partially supported by the Spanish Ministry of Economy and Competitiveness through Grant No. TRA2013-40853-R.