Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Techno-economics optimization of H2 and CO2 compression for renewable energy storage and power-to-gas applications

  • Esteban, Mario
  • Romeo, Luis M.
The decarbonization of the industrial sector is imperative to achieve a sustainable future. Carbon capture and storage technologies are the leading options, but lately the use of CO2 is also being considered as a very attractive alternative that approaches a circular economy. In this regard, power to gas is a promising option to take advantage of renewable H2 by converting it, together with the captured CO2, into renewable gases, in particular renewable methane. As renewable energy production, or the mismatch between renewable production and consumption, is not constant, it is essential to store renewable H2 or CO2 to properly run a methanation installation and produce renewable gas. This work analyses and optimizes the system layout and storage pressure and presents an annual cost (including CAPEX and OPEX) minimization. Results show the proper compression stages need to achieve the storage pressure that minimizes the system cost. This pressure is just below the supercritical pressure for CO2 and at lower pressures for H2, around 67 bar. This last quantity is in agreement with the usual pressures to store and distribute natural gas. Moreover, the H2 storage costs are higher than that of CO2, even with lower mass quantities; this is due to the lower H2 density compared with CO2 . Finally, it is concluded that the compressor costs are the most relevant costs for CO2 compression, but the storage tank costs are the most relevant in the case of H2
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

CO2 recycling in the iron and steel industry via power-to-gas and oxy-fuel combustion

  • Perpiñán, Jorge
  • Bailera, Manuel
  • Romeo, Luis M.
  • Peña, Begoña
  • Eveloy, Valerie
The iron and steel industry is the largest energy-consuming sector in the world. It is responsible for emitting 4-5% of the total anthropogenic CO2. As an energy-intensive industry, it is essential that the iron and steel sector accomplishes important carbon emission reduction. Carbon capture is one of the most promising alternatives to achieve this aim. Moreover, if carbon utilization via power-to-gas is integrated with carbon capture, there could be a significant increase in the interest of this alternative in the iron and steel sector. This paper presents several simulations to integrate oxy-fuel processes and power-to-gas in a steel plant, and compares gas productions (coke oven gas, blast furnace gas, and blast oxygen furnace gas), energy requirements, and carbon reduction with a base case in order to obtain the technical feasibility of the proposals. Two different power-to-gas technology implementations were selected, together with the oxy blast furnace and the top gas recycling technologies. These integrations are based on three strategies: (i) converting the blast furnace (BF) process into an oxy-fuel process, (ii) recirculating blast furnace gas (BFG) back to the BF itself, and (iii) using a methanation process to generate CH4 and also introduce it to the BF. Applying these improvements to the steel industry, we achieved reductions in CO2 emissions of up to 8%, and reductions in coal fuel consumption of 12.8%. On the basis of the results, we are able to conclude that the energy required to achieve the above emission savings could be as low as 4.9 MJ/kg CO2 for the second implementation. These values highlight the importance of carrying out future research in the implementation of carbon capture and power-to-gas in the industrial sector. © 2021 by the authors.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Technical and economic assessment of iron and steelmaking decarbonization via power to gas and amine scrubbing

  • Perpiñán, Jorge
  • Bailera, Manuel
  • Peña, Begoña
  • Romeo, Luis M.
  • Eveloy, Valerie
The iron and steel industry is one of the most energy-intensive industries, emitting 5% of the total anthropogenic carbon dioxide (CO2). The control of CO2 emissions has become increasingly stringent in the European Union (EU), resulting in EU allowance above 90 €/tCO2. Carbon capture will be required to achieve CO2 emissions control, and carbon utilization via power-to-gas could significantly increase interest in carbon capture in the iron and steel sector. This paper presents a new concept that combines amine scrubbing with power-to-gas to reduce emissions in blast furnace-basic oxygen furnace steelmaking plants. Synthetic natural gas (SNG) is produced using green hydrogen from water electrolysis and CO2 from steelmaking. The synthetic natural gas is later used as a reducing agent in the blast furnace, constantly recycling carbon in a closed loop and avoiding geological storage. The oxygen by-produced via electrolysis eliminates the necessity of an air separation unit. By applying these innovations to steelmaking, a reduction in CO2 emissions of 9.4% is obtained with an energy penalty of 16.2 MJ/kgCO2, and economic costs of 52 €/tHM or 283 €/tCO2. A sensitivity analysis with respect to electricity and the CO2 allowances prices is also performed.