Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 7
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Recent progress on bimetallic NiCo and CoFe based electrocatalysts for alkaline oxygen evolution reaction: A review

  • Gebreslase, Gebrehiwet Abrham
  • Martínez Huerta, M. Victoria
  • Lázaro Elorri, María Jesús
16 figures, 10 tables., The deployment of hydrogen as an energy carrier is found to be a vital alternative fuel for the future. It is expected that water electrolysis, powered by renewable energy sources, be able to scale‐up hydrogen production. However, the reaction kinetic of oxygen evolution reaction (OER) is a sluggish process, which predominantly limits the efficiency of water electrolysis. This review recapitulates the recent progress and efforts made in the design and development of two selected earth-abundant bimetallic electrocatalysts (NiCo and CoFe) for alkaline OER. Each bimetal electrocatalyst is thoroughly outlined and discussed in five sub-sections, including bimetal (oxy) hydroxides, Layered double hydroxides (LDHs) structures, oxides, composites, alloy and nanostructured electrocatalysts, and assembled with heteroatoms. Furthermore, a brief introduction to an in situ/operando characterization techniques and advantages for monitoring the structure of the electrocatalysts is provided. Finally, a summary outlining the challenges and conceivable approaches to advance OER performance is highlighted and discussed., Financial support from the European Union’s Horizon 2020 Research and Innovation programme under the Marie Skłodowska-Curie Actions-Innovative Training Networks (MSCA-ITN) Grant Agreement 813748 (Bike project) are gratefully acknowledged. The authors also wish to acknowledge the Ministerio de Ciencia, Innovación y Universidades (MICINN), and FEDER for the received funding in the project of reference ENE2017-83976-C2-1-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Mesoporous Ce-Fe-Ni nanocomposites encapsulated in carbon-nanofibers: Synthesis, characterization and catalytic behavior in oxygen evolution reaction

  • Rosmini, Consolato
  • Tsoncheva, T.
  • Kovatcheva, Daniela
  • Velinov, Nikolay
  • Kolev, Hristo
  • Karashanova, Daniela
  • Dimitrov, M.
  • Tsyntsarski, Boyko
  • Sebastián del Río, David
  • Lázaro Elorri, María Jesús
16 figures, 6 tables.-- Supplementary material available., Ceria-iron oxide mesoporous materials with Fe:Ce molar ratio of 5:5 and 9:1 were synthesized by hydrothermal method using CTAB as a template and subsequently modified with NiO (molar ratio Ni:Fe = 1:2) by incipient wetness impregnation technique. In order to increase the electro-capacitive properties and reduce the intrinsic impedance of the metal oxides, the samples were consecutively modified by reduction in hydrogen to obtain highly dispersed Ni–Fe alloys into ceria matrix. By exploiting the high permeability of carbon inside ferrous alloys, the metal phase has been further modified into ferrous carbides and metal alloys encapsulated within carbon nanofibers. For this purpose, a reaction, already widely studied for the production of hydrogen, was used, that is the decomposition of methanol vapors. In fact, this decomposition, in addition to producing syn-gas and methane, changes the catalysts in use through a chemical vapor deposition-carbon coating process. This fact, has been used by us to demonstrate how the newly obtained metal-carbon nanocomposites can be used for electro-catalytic purposes. The modified phases of the two molar ratios of the Fe–Ni–Ce catalysts were tested in the Oxygen Evolution Reaction (OER) in an alkaline environment (1 M KOH), showing a satisfactory and progressive increase in activity and a surprising decrease in the overpotential at 10 mA/cm2 of current density. The morphological, textural and physicochemical properties of the samples were characterized in details by XRD, N2-physisorption, TG-TPO, TEM, EDX, FTIR, XPS, Raman and Moessbauer spectroscopies., This research was funded by the BIKE project, which received funding from the European Union's Horizon 2020 research and innovation program under the Marie Sklodowska-Curie grant agreement no. 813748., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Transformation of CoFe2O4 spinel structure into active and robust CoFe alloy/N-doped carbon electrocatalyst for oxygen evolution reaction

  • Gebreslase, Gebrehiwet Abrham
  • Martínez Huerta, M. Victoria
  • Sebastián del Río, David
  • Lázaro Elorri, María Jesús
11 figures, 2 tables.-- Supplementary information available., Electrochemical water splitting is an environmentally benign technology employed for H2 production; however, it is critically hampered by the sluggish kinetics of the oxygen evolution reaction (OER) at the positive electrode. In this work, nitrogen-doped carbon-coated CoFe electrocatalysts were synthesized via a three-step route comprising (1) hydrothermal reaction, (2) in-situ polymerization of dopamine and (3) carbonization. The effect of carbonized polydopamine on the overall physicochemical properties and electrochemical activity of CoFe catalysts was systematically studied. By controlling and optimizing the ratio of CoFe2O4 and dopamine contents, a transformation of the CoFe2O4 structure to CoFe alloy was observed. It was found that CoFe/NC30% (prepared with 30% dopamine) exhibits an excellent catalytic activity towards OER. A small overpotential of 340 mV was required to generate a current density of 10 mA cm-2 in a 1.0 M KOH electrolyte. More importantly, the CoFe/NC30% catalyst reflected exceptional durability for at least 24 h. This research sheds light on the development of affordable, highly efficient, and durable electrocatalysts for OER., Financial support from the European Union's Horizon 2020 Research and Innovation programme under the Marie Skłodowska-Curie Actions-Innovative Training Networks (MSCA-ITN) Grant Agreement 813748 are gratefully acknowledged. The authors wish to acknowledge the grants PID2020-115848RB-C21 and PID2020-115848RB-C22 funded by MCIN/AEI/10.13039/501100011033., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nitrogen-doped carbon decorated-Ni3Fe@Fe3O4 electrocatalyst with enhanced oxygen evolution reaction performance

  • Gebreslase, Gebrehiwet Abrham
  • Sebastián del Río, David
  • Martínez Huerta, M. Victoria
  • Lázaro Elorri, María Jesús
11 figures, 2 tables.-- Supplementary information available., High performance, durable and inexpensive electrocatalyst for oxygen evolution reaction (OER) is of great importance for tenable hydrogen production via water electrolysis. Although spinel oxides (AB2O4, A, B = metal) represent a class of promising candidates for OER, their intrinsically poor electrical conductivity impacts their electrochemical performance. Herein, we employed a facile approach to transform an intrinsically low active NiFe2O4 into nitrogen-doped carbon decorated Ni3Fe@Fe3O4 catalyst with improved activity and stability for alkaline OER. Initially, a pristine NiFe2O4 octahedron-like structure was synthesized by a hydrothermal route. Then, series electrocatalysts were prepared by incorporating the pristine NiFe2O4 with different dopamine concentrations via in-situ polymerizations of dopamine followed by carbonization. The morphology, crystalline structure, and chemical composition of the catalysts were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and inductively coupled plasma (ICP). The OER electrocatalysis performance was measured in a standard three-electrode system. The effect of the carbonized dopamine on the electrocatalytic activity and structure of the NiFe2O4 precursor was systematically investigated. Among several NiFe electrocatalysts, the one with 10 wt% of dopamine (NiFe/NC10%) exhibited a relatively higher catalytic activity for OER tested in 1.0 M KOH; unveiled low overpotential (350 mV at 10 mAcm−2 current density), a low Tafel slope (56 mVdec−1), low charge transfer resistance, relatively higher electrochemically active surface area. Most prominently, it remained stable for at least 12 h. This work provides a new perspective for functionalizing metal oxides and affords a facile synthesis approach, low-cost, high-performance, and robust electrocatalyst for alkaline OER electrodes., Financial support from the European Union's Horizon 2020 Research and Innovation programme under the Marie Skłodowska-Curie Actions–Innovative Training Networks (MSCA-ITN) Grant Agreement 813748 are gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

CoFe-loaded P, N co-doped carbon foam derived from petroleum pitch waste: An efficient electrocatalyst for oxygen evolution reaction

  • Gebreslase, Gebrehiwet Abrham
  • Sebastián del Río, David
  • Martínez Huerta, M. Victoria
  • Tsoncheva, T.
  • Tsyntsarski, Boyko
  • Georgiev, Georgi
  • Lázaro Elorri, María Jesús
13 figures, 4 tables.-- Supplementary material available., Designing and developing affordable, high-performance, and stable electrocatalysts for oxygen evolution reaction (OER) is decisive for pragmatic water electrolysis to produce green hydrogen energy. In this work, we report cobalt and iron incorporated in phosphorus and nitrogen co-doped carbon foam (CF) derived from petroleum pitch as a promising electrocatalyst for alkaline OER. The P, N heteroatoms co-doped carbon foam (PN-CF) was first synthesized via thermo-chemical treatment of low-cost petroleum pitch in the presence of melamine (N source) and sodium hypophosphite (P source) precursors, followed by carbonization. Then, mono and bimetals of Co and Fe were impregnated into the as-prepared composite carbon foam (PN-CF) substrate, followed by further carbonization. Among the different catalysts, the bimetallic CoFe integrated with the PN-CF (CoFe@PN-CF) reveals an outstanding electrocatalytic activity (320 mV overpotential at j = 10 mA·cm-2), low Tafel slope (48 mV·dec-1), and excellent durability during OER measurement in 1 M KOH aqueous solution. The superb performance of the CoFe@PN-CF catalyst stems from the synergetic effect of the bimetals confined on phosphorus and nitrogen co-doped carbon foam support with high specific surface area, highly porous structure, and formation of graphitic domains, which enhances the electrical conductivity. This work sheds light on the potential for valorizing petroleum pitch and provides a facile synthesis approach to synthesizing a low-cost, high-performance, and durable electrocatalyst for alkaline OER., Financial support from the European Union's Horizon 2020 Research and Innovation programme under the Marie Skłodowska-Curie Actions−Innovative Training Networks (MSCA-ITN) Grant Agreement 813748 are gratefully acknowledged., Peer reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Mechanochemically engineered bimetallic PtNi/CeO2 catalysts for enhanced methane steam reforming

  • Braga, Andrea
  • Armengol Profitós, Marina
  • Pascua Solé, Laia|||0000-0001-9791-4586
  • Soler Turu, Lluís|||0000-0003-1591-3366
  • Serrano Carreño, M. Isabel|||0000-0002-4996-9280
  • Villar García, Ignacio J.
  • Pérez Dieste, Virginia
  • Llorca Piqué, Jordi|||0000-0002-7447-9582
  • Jiménez Divins, Nuria|||0000-0001-6010-5419
Bimetallic PtNi/CeO2 catalysts were successfully synthesized via a mechanochemical approach, specifically ball milling, and evaluated for methane steam reforming (MSR). A fractional factorial design of experiments was employed to systematically explore the effects of key milling parameters-milling frequency, milling time, and ball-to-powder ratio-on the catalysts’ structural properties and catalytic performance. The catalysts were characterized by X-ray diffraction, H2 temperature-programmed reduction, transmission electron microscopy, and Raman spectroscopy. Catalytic activity tests were performed in a plug flow reactor under a high gas hourly space velocity (200,000 mL gcat–1 h–1) at a steam-to-carbon ratio of 2 between 700 and 950 °C. The mechanochemically synthesized catalysts were benchmarked against those prepared via incipient wetness impregnation. The most active milled catalysts achieved a methane conversion rate of ca. 22 mol CH4 gNi–1 h–1 at 700 °C (83.5% methane conversion for a PtNi/CeO2 mechanochemically synthesized), outperforming the impregnated counterpart (64% methane conversion under the same reaction conditions). Notably, increasing the milling intensity resulted in enhanced catalytic activity, with milling frequency emerging as the most influential factor-correlating with the formation of smaller NiO particles. To elucidate the role of Pt addition, in situ X-ray absorption near-edge structure (XANES) and near-ambient pressure X-ray photoelectron spectroscopy (NAP-XPS) measurements were conducted on the most active milled catalysts under MSR conditions. NAP-XPS revealed surface segregation of Pt during MSR, alongside an inhibitory effect on solid carbon deposition, suggesting the potential for a coke-resistant catalyst. These findings highlight the power of mechanochemical synthesis in tuning catalyst properties, offering a scalable and efficient route to high-performance catalysts for methane reforming and hydrogen production., This work was supported by grant PID2024-156765OB-C21 and is part of Maria de Maeztu Units of Excellence ProgrammeCEX2023-001300-M funded by MCIN/AEI/ 10.13039/501100011033. A.B. is grateful to the European Union’s H2020 research and innovation program under the Marie Skłodowska-Curie grant agreement no. 813748. M.A.-P. is grateful for the 2020 FISDU 00219 grant from Generalitat de Catalunya. L.P.-S. is grateful for the 2022 FI_B 00 205 grant from Generalitat de Catalunya. J.L. is a Serra Húnter Fellow and is grateful to the Academia Excellence program (Generalitat de Catalunya). N.J.D. acknowledges the funding received from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement no. 897197. In situ synchrotron NAP-XPS experiments were performed at the CIRCE beamline at ALBA Synchrotron with the collaboration of ALBA staff. We would like to thank the Institute for Beam Physics and Technology (IBPT) for the operation of the storage ring, the Karlsruhe Research Accelerator (KARA). We acknowledge the KIT Light Source for the provision of instruments at the CAT-ACT beamline of the Institute of Catalysis Research and Technology (IKFT), in particular Dr. Danielle Santos Goncalves (IKFT) for her help and technical support during experiments. We would also like to thank Dr. Maria Casapu from KIT for her support during the XAS experiments., Peer Reviewed, Article signat per 13 autors/es: Andrea Braga - Department of Chemical Engineering, Institute of Energy Technologies, and Center for Research in Multiscale Science and Engineering, EEBE, Universitat Politècnica de Catalunya, Eduard Maristany 10-14, Barcelona 08019, Spain Marina Armengol-Profitós - Department of Chemical Engineering, Institute of Energy Technologies, and Center for Research in Multiscale Science and Engineering, EEBE, Universitat Politècnica de Catalunya, Eduard Maristany 10-14, Barcelona 08019, Spain; Orcid. https://orcid.org/0000-0002-1697-2045 Laia Pascua-Solé - Department of Chemical Engineering, Institute of Energy Technologies, and Center for Research in Multiscale Science and Engineering, EEBE, Universitat Politècnica de Catalunya, Eduard Maristany 10-14, Barcelona 08019, Spain; Orcid. https://orcid.org/0000-0001-9791-4586 Lluís Soler - Department of Chemical Engineering, Institute of Energy Technologies, and Center for Research in Multiscale Science and Engineering, EEBE, Universitat Politècnica de Catalunya, Eduard Maristany 10-14, Barcelona 08019, Spain; Orcid. https://orcid.org/0000-0003-1591-3366 Isabel Serrano - Department of Chemical Engineering, Institute of Energy Technologies, and Center for Research in Multiscale Science and Engineering, EEBE, Universitat Politècnica de Catalunya, Eduard Maristany 10-14, Barcelona 08019, Spain Ignacio J. Villar-Garcia - ALBA Synchrotron Light Source, Carrer de la Llum 2-26, Cerdanyola Del Vallès, Barcelona 08290, Spain Virginia Pérez-Dieste - ALBA Synchrotron Light Source, Carrer de la Llum 2-26, Cerdanyola Del Vallès, Barcelona 08290, Spain Enrico Tusini - Institute for Chemical Technology and Polymer Chemistry, Karlsruhe Institute of Technology (KIT), Engesserstraße 20, Karlsruhe 76131, Germany Andrea De Giacinto - Institute for Chemical Technology and Polymer Chemistry, Karlsruhe Institute of Technology (KIT), Engesserstraße 20, Karlsruhe 76131, Germany; Orcid. https://orcid.org/0009-0006-6959-1381 Anna Zimina - Institute of Catalysis Research and Technology, Karlsruhe Institute of Technology (KIT), Hermann-von-Helmholtz-Platz 1, Eggenstein-Leopoldshafen 76344, Germany; Orcid. https://orcid.org/0000-0002-3111-7741 Jan-Dierk Grunwaldt - Institute for Chemical Technology and Polymer Chemistry, Karlsruhe Institute of Technology (KIT), Engesserstraße 20, Karlsruhe 76131, Germany; Institute of Catalysis Research and Technology, Karlsruhe Institute of Technology (KIT), Hermann-von-Helmholtz-Platz 1, Eggenstein-Leopoldshafen 76344, Germany; Orcid. https://orcid.org/0000-0003-3606-0956
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Mechanochemically engineered bimetallic PtNi/CeO2 catalysts for enhanced methane steam reforming

  • Braga, Andrea
  • Armengol Profitós, Marina
  • Pascua Solé, Laia
  • Soler Turu, Lluís
  • Serrano Carreño, M. Isabel
  • Villar García, Ignacio J.
  • Pérez Dieste, Virginia
  • Llorca Piqué, Jordi
  • Jiménez Divins, Nuria
Bimetallic PtNi/CeO2 catalysts were successfully synthesized via a mechanochemical approach, specifically ball milling, and evaluated for methane steam reforming (MSR). A fractional factorial design of experiments was employed to systematically explore the effects of key milling parameters-milling frequency, milling time, and ball-to-powder ratio-on the catalysts’ structural properties and catalytic performance. The catalysts were characterized by X-ray diffraction, H2 temperature-programmed reduction, transmission electron microscopy, and Raman spectroscopy. Catalytic activity tests were performed in a plug flow reactor under a high gas hourly space velocity (200,000 mL gcat–1 h–1) at a steam-to-carbon ratio of 2 between 700 and 950 °C. The mechanochemically synthesized catalysts were benchmarked against those prepared via incipient wetness impregnation. The most active milled catalysts achieved a methane conversion rate of ca. 22 mol CH4 gNi–1 h–1 at 700 °C (83.5% methane conversion for a PtNi/CeO2 mechanochemically synthesized), outperforming the impregnated counterpart (64% methane conversion under the same reaction conditions). Notably, increasing the milling intensity resulted in enhanced catalytic activity, with milling frequency emerging as the most influential factor-correlating with the formation of smaller NiO particles. To elucidate the role of Pt addition, in situ X-ray absorption near-edge structure (XANES) and near-ambient pressure X-ray photoelectron spectroscopy (NAP-XPS) measurements were conducted on the most active milled catalysts under MSR conditions. NAP-XPS revealed surface segregation of Pt during MSR, alongside an inhibitory effect on solid carbon deposition, suggesting the potential for a coke-resistant catalyst. These findings highlight the power of mechanochemical synthesis in tuning catalyst properties, offering a scalable and efficient route to high-performance catalysts for methane reforming and hydrogen production., This work was supported by grant PID2024-156765OB-C21 and is part of Maria de Maeztu Units of Excellence ProgrammeCEX2023-001300-M funded by MCIN/AEI/ 10.13039/501100011033. A.B. is grateful to the European Union’s H2020 research and innovation program under the Marie Skłodowska-Curie grant agreement no. 813748. M.A.-P. is grateful for the 2020 FISDU 00219 grant from Generalitat de Catalunya. L.P.-S. is grateful for the 2022 FI_B 00 205 grant from Generalitat de Catalunya. J.L. is a Serra Húnter Fellow and is grateful to the Academia Excellence program (Generalitat de Catalunya). N.J.D. acknowledges the funding received from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement no. 897197. In situ synchrotron NAP-XPS experiments were performed at the CIRCE beamline at ALBA Synchrotron with the collaboration of ALBA staff. We would like to thank the Institute for Beam Physics and Technology (IBPT) for the operation of the storage ring, the Karlsruhe Research Accelerator (KARA). We acknowledge the KIT Light Source for the provision of instruments at the CAT-ACT beamline of the Institute of Catalysis Research and Technology (IKFT), in particular Dr. Danielle Santos Goncalves (IKFT) for her help and technical support during experiments. We would also like to thank Dr. Maria Casapu from KIT for her support during the XAS experiments., Peer Reviewed, Article signat per 13 autors/es: Andrea Braga - Department of Chemical Engineering, Institute of Energy Technologies, and Center for Research in Multiscale Science and Engineering, EEBE, Universitat Politècnica de Catalunya, Eduard Maristany 10-14, Barcelona 08019, Spain Marina Armengol-Profitós - Department of Chemical Engineering, Institute of Energy Technologies, and Center for Research in Multiscale Science and Engineering, EEBE, Universitat Politècnica de Catalunya, Eduard Maristany 10-14, Barcelona 08019, Spain; Orcid. https://orcid.org/0000-0002-1697-2045 Laia Pascua-Solé - Department of Chemical Engineering, Institute of Energy Technologies, and Center for Research in Multiscale Science and Engineering, EEBE, Universitat Politècnica de Catalunya, Eduard Maristany 10-14, Barcelona 08019, Spain; Orcid. https://orcid.org/0000-0001-9791-4586 Lluís Soler - Department of Chemical Engineering, Institute of Energy Technologies, and Center for Research in Multiscale Science and Engineering, EEBE, Universitat Politècnica de Catalunya, Eduard Maristany 10-14, Barcelona 08019, Spain; Orcid. https://orcid.org/0000-0003-1591-3366 Isabel Serrano - Department of Chemical Engineering, Institute of Energy Technologies, and Center for Research in Multiscale Science and Engineering, EEBE, Universitat Politècnica de Catalunya, Eduard Maristany 10-14, Barcelona 08019, Spain Ignacio J. Villar-Garcia - ALBA Synchrotron Light Source, Carrer de la Llum 2-26, Cerdanyola Del Vallès, Barcelona 08290, Spain Virginia Pérez-Dieste - ALBA Synchrotron Light Source, Carrer de la Llum 2-26, Cerdanyola Del Vallès, Barcelona 08290, Spain Enrico Tusini - Institute for Chemical Technology and Polymer Chemistry, Karlsruhe Institute of Technology (KIT), Engesserstraße 20, Karlsruhe 76131, Germany Andrea De Giacinto - Institute for Chemical Technology and Polymer Chemistry, Karlsruhe Institute of Technology (KIT), Engesserstraße 20, Karlsruhe 76131, Germany; Orcid. https://orcid.org/0009-0006-6959-1381 Anna Zimina - Institute of Catalysis Research and Technology, Karlsruhe Institute of Technology (KIT), Hermann-von-Helmholtz-Platz 1, Eggenstein-Leopoldshafen 76344, Germany; Orcid. https://orcid.org/0000-0002-3111-7741 Jan-Dierk Grunwaldt - Institute for Chemical Technology and Polymer Chemistry, Karlsruhe Institute of Technology (KIT), Engesserstraße 20, Karlsruhe 76131, Germany; Institute of Catalysis Research and Technology, Karlsruhe Institute of Technology (KIT), Hermann-von-Helmholtz-Platz 1, Eggenstein-Leopoldshafen 76344, Germany; Orcid. https://orcid.org/0000-0003-3606-0956, Postprint (published version)