Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Relevance of oxygen carrier properties on the design of a chemical looping combustion unit with gaseous fuels

  • Abad Secades, Alberto
  • Gayán Sanz, Pilar
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
  • Izquierdo Pantoja, María Teresa
  • Mendiara, Teresa
  • Adánez Elorza, Juan
12 figures, 6 tables.-- Supplementary information available.-- Special Issue: CCUS contributions from the Spanish CO2 Technology Platform Association (PTECO2), Chemical looping combustion (CLC) is a novel technology for the combustion of fuels with inherent CO2 capture. CLC is based on the transference of oxygen from air to fuel by means of an oxygen carrier which is based on a metal oxide. CuO/Al2O3 (14 wt.% CuO) and Fe2O3/Al2O3 (20 wt.% Fe2O3) particles have been used in several CLC units with different results when methane combustion was evaluated. In order to shed light on the main processes affecting methane conversion in CLC, a mathematical model for a dual circulating fluidized bed (DCFB) system was developed to simulate the behavior of CuO/Al2O3 and Fe2O3/Al2O3 in a CLC unit. The model consists of the coupling of individual fuel and air reactor models to simulate steady state of the CLC unit. Individual models consider both the fluid dynamics of the fluidized beds at the high velocity regime and the corresponding kinetics of oxygen carrier reactions, that is, reduction in the fuel reactor and oxidation in the air reactor. The model was validated using results obtained in a 120 kWth CLC unit with CuO/Al2O3 and Fe2O3/Al2O3 particles. The validated model was used to simulate the performance of these materials in the 10 MWth CLC unit. Desing parameters of the fuel and air reactors as well as the suitable particle size of the oxygen carriers were determined in order to achieve the complete combustion of natural gas in the CLC unit as a function of the oxygen carrier properties., This work was supported by Grant funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Life cycle assessment of power-to-methane systems with CO2 supplied by the chemical looping combustion of biomass

  • Navajas, A.
  • Mendiara, Teresa
  • Gandía, L. M.
  • Abad Secades, Alberto
  • García Labiano, Francisco
  • Diego Poza, Luis F. de
8 figures, 5 tables.-- Supplementary information available., Power-to-methane (PtM) systems may allow fluctuations in the renewable energy supply to be smoothed out by storing surplus energy in the form of methane. These systems work by combining the hydrogen produced by electrolysis with carbon dioxide from different sources to produce methane via the Sabatier reaction. The present work studies PtM systems based on the CO supplied by the chemical looping combustion (CLC) of biomass (PtM-bioCLC). Life- cycle- assessment (LCA) was performed on PtM-bioCLC systems to evaluate their environmental impact with respect to a specific reference case. The proposed configurations have the potential to reduce the value of the global warming potential (GWP) climate change indicator to the lowest values reported in the literature to date. Moreover, the possibility of effectively removing CO from the atmosphere through the concept of CO negative emissions was also assessed. In addition to GWP, as many as 16 LCA indicators were also evaluated and their values for the studied PtM-bioCLC systems were found to be similar to those of the reference case considered or even significantly lower in such categories as resource use-depletion, ozone depletion, human health, acidification potential and eutrophication. The results obtained highlight the potential of these newly proposed PtM schemes., This work was supported by Grant PDC2021-121190-I00 funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR and also by Grant PID2020-113131RB-I00 funded by MICIN/AEI/10.13039/501100011033. A.N. and L.M.G. gratefully acknowledge Grant RTI2018-096294-B-C31 funded by MCIN/AEI/10.13039/501100011033 and “ERDF A way of making Europe”., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Combustión de biomasa pino con dos transportadores de oxígeno magnéticos basados en óxido de cobre

  • Filsouf, Amirhossein
  • Adánez-Rubio, Iñaki
  • Mendiara, Teresa
  • Izquierdo Pantoja, María Teresa
2 tablas.-- Abstract del póster de Tecnologías para la generación sostenible de energía presentada en la XVI Reunión del Grupo Español del Carbón (Reunión GEC 2023), celebrada en Gijón del 22 al 25 de octubre de 2023., La contribución de las tecnologías de captura de CO2 en la reducción de emisiones es necesaria para cumplir los objetivos del Acuerdo de Parías. Dichas tecnologías, permiten generar corrientes concentradas de CO2en instalaciones de generación de energía. Concretamente, la denominada combustión con transportadores de oxígeno (Chemical Looping Combustion - CLC) destaca como una tecnología prometedora que permite la separación del CO2 del proceso de combustión con un coste y una penalización en la eficiencia relativamente bajos [1]. En esta tecnología, el oxígeno necesario para la combustión lo aporta un transportador de oxígeno (TO) que circula entre dos reactores interconectados. La combustión con TOs con desacoplamiento de oxígeno (Chemical Looping with Oxygen Uncoupling - CLOU) utiliza TOs como CuO/Cu2O, Mn2O3/Mn3O4 y Co3O4/CoO, que tienen la capacidad de liberar oxígeno gas, promoviendo una oxidación eficiente del combustible. El presente trabajo analiza el comportamiento en la combustión de biomasa de pino de dos TOs de óxido de cobre (sin y con adición de caolín)., Este trabajo ha sido realizado bajo la ayuda PDC2021-121190-I00/AEI/10.13039/501100011033 financiada por MCIN/AEI/10.13039/501100011033 y por “Unión Europea NextGenerationEU/PRTR”. Los autores agradecen también la financiación recibida de Combustión y Gasificación T05_20R. I. Adánez-Rubio agradece al MINECO y al CSIC por el contrato post-doctoral Juan de la Cierva-Incorporación (IJC2019-038987-I)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Development of manganese-iron mixed oxides reinforced with titanium and prepared from minerals for their use as oxygen carriers

  • Zornoza, Beatriz
  • Mendiara, Teresa
  • Abad Secades, Alberto
4 figures, 7 tables., Chemical Looping Combustion (CLC) allows CO2 capture at low cost. This technology is based on solid oxygen carriers which supply the oxygen required for combustion of the fuel while they experience successive reduction-oxidation cycles. Oxygen carriers based on minerals or industrial residues present the advantage of their low cost but complete combustion of the fuel is not always achieved. Manganese‑iron mixed oxides doped with titanium can improve combustion efficiency due to its oxygen uncoupling capability. Moreover, they present the advantage of their magnetic properties. The objective of this work was to produce this type of oxygen carriers from minerals/residues instead of from synthetic materials. Four oxygen carriers with a fixed Mn-Fe molar ratio were produced with a 7 wt.% TiO2 addition. Two manganese-based (MnSA and MnGBMPB) and one iron-based (Tierga) minerals were used as source of Mn and Fe, respectively. As source of Ti, the mineral ilmenite was used. After characterization of the materials, their reactivity was analysed in a TGA. The reactivity to the main combustion gasses was lower than that corresponding to similar oxygen carriers obtained from synthetic sources although they maintained their magnetic properties. Thus, its use as magnetic support of oxygen carriers was recommended. In this respect, first tests were conducted using CuO as active phase supported on one of the low-cost support materials produced in this work., This work was supported by Grant PDC2021-121190-I00 MCIN/AEI/10.13039/501100011033 and European Union NextGenerationEU/PRTR. [...]. B.Z. acknowledges the “Juan de la Cierva” Program (IJCI-2016–30776)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Techno-economic analysis of chemical looping processes with biomass resources for energy production and CO2 utilization. Comparison of CLC and CLOU technologies

  • Cabello Flores, Arturo
  • Abad Secades, Alberto
  • Obras-Loscertales, Margarita de las
  • Domingos, Yldeney
  • Mendiara, Teresa
9 figures, 12 tables., Bioenergy coupled with carbon capture utilization and storage (BECCUS) is an attractive greenhouse gas mitigation technology that can produce negative CO2 emissions by combining bioenergy resources with the utilization or geological storage of the captured CO2. The main objective of this work was to evaluate the technical and economic feasibility of two BECCUS technologies based on chemical looping concept with two biomass waste as fuels, i.e., swine manure and pine sawdust, for the production of thermal energy and a pure CO2 stream that is subsequently used as raw material in agricultural greenhouses. Direct use of solid biomass resources was considered for the Chemical Looping with Oxygen Uncoupling option, whereas biogas production was the starting point for Chemical Looping Combustion. The profitability of the chemical looping scenarios was assessed through the Levelized Cost of CO2. This parameter was estimated at 218.31 €/t CO2 for the Chemical Looping Combustion scenario, a value much higher than those for the Chemical Looping with Oxygen Uncoupling scenarios (73.04–87.32 €/t CO2) due to the limited conversion degree of the carbon present in the fuel waste to biogas and the need for an additional experimental plant to the Chemical Looping Combustion unit, i.e., the biogas production plant. Comparing the Chemical Looping with Oxygen Uncoupling scenarios, the economic analysis revealed that the profitability of the biomass-fueled chemical looping facility was markedly sensitive to the selling price of the biomass resource. Furthermore, the values of the Levelized Cost of CO2 parameter for the Chemical Looping with Oxygen Uncoupling scenarios were lower than those estimated in other research studies that implemented BECCUS technologies and utilized the captured CO2 for identical purposes. In the particular case of swine manure, this result becomes even more noteworthy since it demonstrates that the energy use of this biomass resource through Chemical Looping with Oxygen Uncoupling technology is an economically profitable and environmentally sustainable solution to the difficult challenge of managing this livestock waste. Therefore, it can be concluded that Chemical Looping with Oxygen Uncoupling processes fed with biomass are a very attractive BECCUS technology for heat generation where, in addition, the pure CO2 stream obtained at the outlet of the fuel reactor can be considered a marketable, high value-added product., This work was supported by Grant PDC2021-121190-I00 MCIN/AEI/10.13039/501100011033 and the SWINELOOP (PID2019-106441RBI00/AEI/10.13039/501100011033) project. A. Cabello is also grateful for Grant IJC2019-038908-I funded by MCIN/AEI/10.13039/501100011033., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ash interaction with two Cu-based magnetic oxygen carriers during biomass combustion by the chemical looping with oxygen uncoupling process

  • Filsouf, Amirhossein
  • Adánez-Rubio, Iñaki
  • Mendiara, Teresa
  • Abad Secades, Alberto
  • Adánez Elorza, Juan
10 figures, 4 tables., Chemical-looping combustion (CLC) stands out as a promising method for carbon capture and storage for the purpose of mitigating climate change. The process involves the conversion of fuel facilitated by an oxygen carrier, with the resulting CO2 inherently separated from other air components. Notably, when applied to biomass combustion this process offers a pathway to achieving negative CO2 emissions. However, a significant challenge for CLC, particularly in its application to biomass, is the management of interactions between ash and oxygen carriers. Biomass-derived ashes typically contain substantial quantities of reactive ash-forming substances, such as alkaline and alkali earth elements. These interactions can impact the performance and longevity of the oxygen carrier, necessitating careful consideration and mitigation strategies in CLC systems utilizing biomass feedstocks. This study examined the interaction between biomass ash components and two recently developed oxygen carriers, Cu30MnFekao7.5 and Cu30MnFe, during combustion in a 1.5 kWth continuous unit. Both oxygen carriers achieved 100% combustion efficiency and a CO2 capture efficiency of 95% at 900 °C. Although the copper in both oxygen carriers did not exhibit any noticeable interaction with ash components, the accumulative presence of potassium and magnesium in Cu30MnFekao7.5 was identified by inductively coupled plasma and scanning electron microscopy with energy dispersive X-ray analysis, indicating an increase in the amount of both elements in the particles after combustion operation. No problems of agglomeration or fluidization were observed in any of the experiments., This work was supported by PDC2021-121190-I00/AEI/10.13039/501100011033, financed by MCIN/AEI/10.13039/501100011033 and the European Union NextGenerationEU/PRTR. I.A.-R. acknowledges the Juan de la Cierva Programme (Grant IJC2019-038987-I funded by MCIN/AEI/10.13039/501100011033) and the Ramón y Cajal Programme (Grant RYC2022-035841-I funded by MCIU/AEI/10.13039/501100011033 and FSE+)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Reviewing the operational experience on chemical looping combustion of biomass at CSIC: iG-CLC vs CLOU

  • Abad Secades, Alberto
  • García Labiano, Francisco
  • Izquierdo Pantoja, María Teresa
  • Mendiara, Teresa
  • Gayán Sanz, Pilar
  • Adánez-Rubio, Iñaki
  • Adánez Elorza, Juan
21 figures, 5 tables., The unmixed combustion of biomass by chemical looping (Bio-CLC) has outstanding properties to produce energy by thermochemical conversion with CO2 capture at low economic and energetic costs as well as minimizing NOx emissions to the atmosphere. A detailed analysis of the experimental results during the biomass combustion in chemical looping combustion (CLC) units is useful to evaluate the Bio-CLC potential for future industrial up-scaling. This work compiles the results obtained during more than 500 h of combustion in the previous years at the Instituto de Carboquímica (ICB-CSIC). Different biomasses were burnt with several oxygen carriers in two singular CLC units. Critical key performance indicators, such as the CO2 capture rate and combustion efficiency, have been evaluated considering the combustion mode and the fluidization regime in the fuel reactor. Regarding the combustion mode, results by in situ gasification (iG-CLC) vs chemical looping with oxygen uncoupling (CLOU) are compared. As for the fluidization regime, it was bubbling in a 0.5 kWth CLC unit and circulating in a 50 kWth CLC unit. A methodical comparison of the results allows us to understand the fundamentals of the processes and to evaluate the different behaviors observed in each case. The operating conditions having major effects on the Bio-CLC performance were identified, as well as the operating conditions necessary to optimize the CO2 capture and the combustion efficiency. In addition, other issues are evaluated, such as the fate of fuel-N in a CLC process, the presence of tar compounds in the CO2 stream, or the interaction of ash compounds with the oxygen carrier particles. Finally, possible future actions are discussed to improve the performance of the Bio-CLC process as well as the possible development paths of new oxygen carriers., This work was supported by Grant PDC2021-121190-I00 funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR and the Grant T05_23R founded by the Government of Aragon. I.A.-R. acknowledges the “Ramón y Cajal” Program (Grant RYC2022-035841-I funded by MCIU/AEI/10.13039/501100011033 and FSE+)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Chemical looping with oxygen uncoupling of biomass and coal: scaling-up to 50 kWth using a copper-based oxygen carrier

  • Abad Secades, Alberto
  • Filsouf, Amirhossein
  • Adánez-Rubio, Iñaki
  • Mendiara, Teresa
  • Diego Poza, Luis F. de
  • Izquierdo Pantoja, María Teresa
  • Gayán Sanz, Pilar
  • Adánez Elorza, Juan
15 figures, 5 tables., Chemical looping with oxygen uncoupling (CLOU) is an advanced CO2 capture technology where an oxygen carrier supplies the gaseous oxygen required for combustion. The technology has experienced a significant development degree in the most recent decades, up to TRL 4. This study presents results that further prove the viability of this technology to TRL 5 in a continuous CLC unit with two interconnected circulating fluidized beds acting as fuel and air reactors. The oxygen carrier used in the experiments was a magnetic copper-based oxygen carrier denoted as Cu30MnFe. It was used in the combustion of three types of biomass and a bituminous coal (Taldinsky coal). The effects on char conversion, CO2 capture efficiency, and total oxygen demand of different parameters such as excess air ratio, fuel reactor temperature, residence time in fuel reactor, gas velocity in the carbon stripper, solid circulation rate, and solid inventory in fuel reactor were investigated. CO2 capture efficiency of 93% was achieved at 886 °C with pine sawdust combustion, while the total oxygen demand was 4.6%. In the experiments with bituminous coal, the effectiveness of the carbon stripper in improving the CO2 capture efficiency was demonstrated. During the highest load of coal, low total oxygen demands were achieved even at temperatures below 900 °C., This work was supported by Grant PDC2021-121190-I00 funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR. I.A.-R. acknowledges the “Ramón y Cajal” Program (Grant RYC2022-035841-I funded by MCIU/AEI/10.13039/501100011033 and FSE+)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Chemical looping combustion and gasification of swine manure with a Cu-Based oxygen carrier

  • Domingos, Yldeney
  • Abad Secades, Alberto
  • Obras-Loscertales, Margarita de las
  • Izquierdo Pantoja, María Teresa
  • Cabello Flores, Arturo
12 figures, 6 tables., The thermochemical conversion of swine manure by using Chemical Looping Combustion (CLC) and Chemical Looping Gasification (CLG) is an interesting option to obtain bioenergy and solve some environmental issues related to this waste. In this work, experimental tests using swine manure as fuel and a Cu-based oxygen carrier (14 wt% CuO) in a 0.5kWth continuous unit have been performed. For CLC conditions, the effects of the temperature (800–900 °C) and the fluidization agent (CO2 or steam) on the combustion and CO2 capture efficiencies were evaluated. In general, high combustion (97–99 %) and CO2 capture (87–99 %) efficiencies were achieved, which improved by increasing the operating temperature. For CLG conditions, the effect of the oxygen-to-fuel ratio (λ = 0.2, 0.3 and 0.4) on the gas product distribution, CO2 capture efficiency and tar composition was studied using steam and CO2 as fluidizing agents at 900 °C. The CO2 capture potential improved by increasing the oxygen-to-fuel ratio. Regarding the tar distribution, naphthalene was the main product followed by benzene, acenaphthylene, indene and phenanthrene. Additionally, for both processes, CLC and CLG, the distribution of nitrogenous compound emissions (N2, NH3, N2O, NO2 and NO) was analyzed. It was observed that the N-swine manure was mainly converted into inert N2., This work was supported by project SWINELOOP, grant PID2019-106441RB-I00 funded by MCIN/AEI/10.13039/501100011033. This work was supported by Grant PDC2021-121190-I00 funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR“. Y. Domingos thanks for the grant PRE-092769 Pre-Doctoral fellowship, funded by MCIN/AEI/10.13039/501100011033 and by “ESF Investing in your future”., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Performance of granulated Ti-dopped manganese oxide oxygen carriers in Chemical Looping processes

  • Mendiara, Teresa
  • Filsouf, Amirhossein
  • Adánez-Rubio, Iñaki
  • Izquierdo Pantoja, María Teresa
  • Abad Secades, Alberto
12 figures, 4 tables., The cornerstone in the development of different applications of the Chemical Looping (CL) technology is the oxygen carrier material that transfers the oxygen. We evaluate the performance of manganese oxide doped with TiO2 to reinforce the release of molecular oxygen and regeneration at high temperatures (850–950 °C). Different manganese-titanium mixed oxides with mass fractions of titanium oxide from 0 to 50 wt.% were considered and prepared by granulation. The sample with 20 wt.%. TiO2 (MnTi_20) showed better oxygen release/regeneration capabilities than pure manganese oxide under similar conditions and was selected for further development. To evaluate the performance of MnTi_20, long tests (200 cycles) were carried out in a TGA to evaluate the chemical and mechanical stability of the sample. Additionally, MnTi_20 was tested in a batch fluidized bed reactor to evaluate its oxygen uncoupling capability and its reactivity with the main combustion gases (H2, CO, and CH4) as well as its fluidization properties. MnTi_20 is capable of regenerating Mn3O4 to Mn2O3 at 950 °C and maintains its reactivity with the redox cycles. No fluidization problems were encountered during almost 60 h of continuous fluidization, and a lifetime of 2500 h was estimated for this oxygen carrier., This research was funded by the PDC2021-121190-I00/AEI/10.13039/501100011033 financed by MCIN/AEI/10.13039/501100011033 and European Union NextGenerationEU/PRTR. The authors also thank the funding received from Gobierno de Aragón—Dpto. de Ciencia, Universidad y Sociedad del Conocimiento—Project LMP166_21, I. Adánez-Rubio acknowledges for “Ramón y Cajal” Program (Grant RYC2022-035841-I funded by MCIU/AEI/10.13039/501100011033 and FSE+)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Physicochemical evolution of a Cu/Mn/Fe oxygen carrier in a 50 kWth chemical looping with oxygen uncoupling unit with solid fuels

  • Filsouf, Amirhossein
  • Mendiara, Teresa
  • Adánez-Rubio, Iñaki
  • Izquierdo Pantoja, María Teresa
  • Adánez Elorza, Juan
  • Gayán Sanz, Pilar
  • Abad Secades, Alberto
14 figures, 4 tables.-- Under a Creative Commons BY-NC 4.0 International license., Chemical looping combustion with oxygen uncoupling (CLOU) is a promising technology for efficient CO2 capture. Identification of a suitable oxygen carrier is a key issue for the scale-up of the CLOU process. This study investigates the performance of a CuMnFe-based oxygen carrier (Cu30MnFe) after 40 h of operation in a 50 kWth CLOU unit using various solid fuels, including biomass and coal. Key physicochemical properties such as porosity, magnetic permeability, mechanical strength, particle size distribution, and phase composition were monitored throughout the campaign. Results revealed increased porosity and reduced mechanical strength, with chipping identified as the dominant attrition mechanism. Despite particle degradation, magnetic separation remained highly effective (99.5 %) for separation of fine particles from ash. SEM-EDX and ICP-OES analyses confirmed the chemical stability of Cu, Mn, and Fe, although a transformation from CuO to a spinel-type Cu-Mn-Fe oxide phase was observed, maintaining oxygen release capacity. Surface accumulation of ash elements like Si was detected, but no operational issues such as agglomeration or defluidization occurred. This work represents a step forward in the knowledge of Cu-based materials and will be useful for the future development of durable oxygen carriers with oxygen uncoupling and magnetic properties., This work was supported by Grant PDC2021-121190-I00 funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR. Iñaki Adánez-Rubio acknowledges for “Ramón y Cajal” Program (Grant RYC2022-035841-Ifunded by MCIU/AEI/10.13039/501100011033 and FSE + )., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Development of manganese-iron mixed oxides reinforced with titanium and prepared from minerals for their use as oxygen carriers

  • Zornoza, Beatriz
  • Mendiara, Teresa
  • Abad, Alberto
Chemical Looping Combustion (CLC) allows CO2 capture at low cost. This technology is based on solid oxygen carriers which supply the oxygen required for combustion of the fuel while they experience successive reduction-oxidation cycles. Oxygen carriers based on minerals or industrial residues present the advantage of their low cost but complete combustion of the fuel is not always achieved. Manganese‑iron mixed oxides doped with titanium can improve combustion efficiency due to its oxygen uncoupling capability. Moreover, they present the advantage of their magnetic properties. The objective of this work was to produce this type of oxygen carriers from minerals/residues instead of from synthetic materials. Four oxygen carriers with a fixed Mn-Fe molar ratio were produced with a 7 wt.% TiO2 addition. Two manganese-based (MnSA and MnGBMPB) and one iron-based (Tierga) minerals were used as source of Mn and Fe, respectively. As source of Ti, the mineral ilmenite was used. After characterization of the materials, their reactivity was analysed in a TGA. The reactivity to the main combustion gasses was lower than that corresponding to similar oxygen carriers obtained from synthetic sources although they maintained their magnetic properties. Thus, its use as magnetic support of oxygen carriers was recommended. In this respect, first tests were conducted using CuO as active phase supported on one of the low-cost support materials produced in this work.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Life cycle assessment of power-to-methane systems with CO2 supplied by the chemical looping combustion of biomass

  • Navajas León, Alberto
  • Mendiara, Teresa
  • Gandía Pascual, Luis
  • Abad, Alberto
  • García Labiano, Francisco
  • Diego, Luis F. de
Power-to-methane (PtM) systems may allow fluctuations in the renewable energy supply to be smoothed out by storing surplus energy in the form of methane. These systems work by combining the hydrogen produced by electrolysis with carbon dioxide from different sources to produce methane via the Sabatier reaction. The present work studies PtM systems based on the CO2 supplied by the chemical looping combustion (CLC) of biomass (PtM-bioCLC). Life- cycle- assessment (LCA) was performed on PtM-bioCLC systems to evaluate their environmental impact with respect to a specific reference case. The proposed configurations have the potential to reduce the value of the global warming potential (GWP) climate change indicator to the lowest values reported in the literature to date. Moreover, the possibility of effectively removing CO2 from the atmosphere through the concept of CO2 negative emissions was also assessed. In addition to GWP, as many as 16 LCA indicators were also evaluated and their values for the studied PtM-bioCLC systems were found to be similar to those of the reference case considered or even significantly lower in such categories as resource use-depletion, ozone depletion, human health, acidification potential and eutrophication. The results obtained highlight the potential of these newly proposed PtM schemes., This work was supported by Grant PDC2021-121190-I00 funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR and also by Grant PID2020-113131RB-I00 funded by MICIN/AEI/10.13039/501100011033. A.N. and L.M.G. gratefully acknowledge Grant RTI2018-096294-B-C31 funded by MCIN/AEI/10.13039/501100011033 and “ERDF A way of making Europe”.