Pasar al contenido principal

NUEVAS TOPOLOGIAS DE CONVERSION, CONFIGURACIONES Y ESTRATEGIAS DE CONTROL PARA LA FUTURA RED ELECTRICA BASADA EN ENERGIAS RENOVABLES

PID2019-110956RB-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2019
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD PUBLICA DE NAVARRA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 20
Encontrada(s) 1 página(s)

Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Control strategy for a droop-controlled grid-connected DFIG wind turbine

  • Oraa Iribarren, Iker
  • Samanes Pascual, Javier
  • López Taberna, Jesús
  • Gubía Villabona, Eugenio
The application of droop control techniques without inner current control loops to doubly-fed induction generator (DFIG) based wind turbines does not allow to provide a stable response at all operating points in terms of rotational speed and active and reactive power. After modeling the system dynamics and analyzing the causes of instability, this paper proposes a control strategy that allows to stabilize the system response at all possible operating points. Simulation results performed in MATLAB/Simulink validate the proposed control strategy proving its effectiveness., This work was supported by the Spanish State Research Agency (AEI) under Grant PID2019-110956RB-I00/AEI/10.13039.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Dual-stage control strategy for a three-level neutral point clamped converter with selective harmonic mitigation PWM

  • Rosado Galparsoro, Leyre
  • Norambuena, Margarita
  • Samanes Pascual, Javier
  • Lezana, Pablo
  • Gubía Villabona, Eugenio
  • López Taberna, Jesús
Grid-connected converters must meet the requirements imposed by grid codes, such as harmonic emission limits and grid voltage support during voltage dips. Selective harmonic mitigation pulsewidth modulation (SHMPWM) is a very interesting technique for high power converters to meet the maximum harmonic emission levels, while keeping a low switching frequency. However, the combination of this modulation with a proportional integral (PI) controller requires slow dynamics, which makes it difficult to comply with the dynamic response requirements of grid codes. As an alternative, model predictive control (MPC) offers a very fast dynamic response, but a wide spread harmonic spectrum in steady state. Thus, the combination of MPC with a PI controller with SHMPWM is advantageous. In this work, a dual-stage control strategy is implemented. During transients, finite control set MPC (FCS-MPC) is activated to rapidly drive the current to the desired reference, while in steady state, the PI controller with SHMPWM is used. Therefore, the dual-stage control strategy allows to comply with the two requirements of grid codes, becoming a suitable strategy for grid-connected converters., This work is part of the projects PID2019-110956RB-I00 and TED2021-132604B-I00, funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR. It has also been partially supported by Ingeteam Power Technology and the Public University of Navarre. The authors also acknowledge the support of ANID through projects FB0008 Advanced Center for Electrical and Electronics Engineering, FONDECYT 1230250.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Dynamic modeling of a pressurized alkaline water electrolyzer: a multiphysics approach

  • Iribarren Zabalegui, Álvaro
  • Elizondo Martínez, David
  • Barrios Rípodas, Ernesto
  • Ibaiondo, Harkaitz
  • Sánchez Ruiz, Alain
  • Arza, Joseba
  • Sanchis Gúrpide, Pablo
  • Ursúa Rubio, Alfredo
In this paper a dynamic model for the simulation of pressurized alkaline water electrolyzers is presented. The model has been developed following a multiphysics approach, integrating electrochemical, thermodynamic, heat transfer and gas evolution processes in order to faithfully reproduce the complete dynamical behavior of these systems. The model has been implemented on MATLAB/Simulink and validated through experimental data from a 1 Nm3/h commercial alkaline water electrolyzer. Validations have been performed under real scenarios where the electrolyzer is working with power profiles characteristic from renewable sources, wind and photovoltaic. The simulated results have been found to be consistent with the real measured values. This model has a great potential to predict the behavior of alkaline water electrolyzers coupled with renewable energy sources, making it a very useful tool for designing efficient green hydrogen production systems., This work has been supported by the Spanish State Research Agency (MCIN/AEI/10.13039/501100011033) under grants PID2019-111262RBI00, PID2019-110956RB-I00 and TED2021-132457B-I00 (also funded by the European Union NextGenerationEU/PRTR), by Ingeteam R&D Europe and by Ingeteam Power Technology.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Modeling a grid-forming DFIG wind turbine

  • Oraa Iribarren, Iker
  • Samanes Pascual, Javier
  • López Taberna, Jesús
  • Gubía Villabona, Eugenio
This paper presents a small-signal state-space model that allows analyzing the dynamics of doubly-fed induction generator (DFIG)-based wind turbines in which grid-forming control strategies are implemented. Specifically, in this paper, a droop-controlled DFIG wind turbine is modeled. The system is modeled in the dq-axis, synchronized with the grid voltage, which simplifies the modeling by not having to linearize the terms dependent on the rotational speed of the dq-axis. Independent models for each element of the system are obtained, which are then combined to model the complete system under study. This modeling methodology provides great flexibility, allowing for easy inclusion of the LC harmonic filter, and enabling future incorporation of the grid-side converter to analyze its interaction with the rotor-side converter. The developed model is validated through simulation, demonstrating that it accurately reproduces the dynamic response of the system under study., This work was supported by the Spanish State Research Agency (AEI) under Grant PID2019-110956RB-I00/AEI/10.13039, the Public University of Navarre (UPNA) and Ingeteam Power Technology.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Effect of the inner current loop on the voltage regulation for three-phase photovoltaic inverters

  • Urtasun Erburu, Andoni
  • Sanchis Gúrpide, Pablo
  • Marroyo Palomo, Luis
In three-phase grid-connected PV inverters, regulating the input voltage is a fundamental requirement. In order to reduce the influence of the PV non-linear behavior and ensure stability in the whole operating range, the input capacitance is currently oversized. This paper reveals the important effect of the inner current loop in the voltage stability and proposes to use a Proportional (P) controller instead of a PI controller. If tuned following the guidelines provided in this paper, the P controller makes it possible to design a stable voltage loop without increasing the input capacitance, thus reducing the converter cost., This work was supported by the Spanish State Research Agency (AEI) under grant PID2019-110956RB-I00/AEI/10.13039 and grant DPI-201680641-R.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

New design alternatives for a hybrid photovoltaic and doubly-fed induction wind plant to augment grid penetration of renewable energy

  • Goñi Pérez, Naiara
  • Sacristán Sillero, Javier
  • Berrueta Irigoyen, Alberto
  • Rodríguez Rabadan, José Luis
  • Ursúa Rubio, Alfredo
  • Sanchis Gúrpide, Pablo
Reducing carbon emissions is essential to stop climate change. The grid-share of renewable generation plants is increasing, being wind and photovoltaic plants the most common ones, whereas conventional plants are the only ones that provide the necessary services to maintain the grid stability and keep the generation-demand balance. However, with the aim of achieving carbon-neutral generation, conventional plants are being dismantled. This leads to the imminent need of providing these services with renewable plants. Due to this challenge, this proposal analyses a hybrid plant composed by wind and photovoltaic generation with two types of storage, lithium-ion batteries and a thermal storage system based on volcanic stones. In order to compare both strategies, a technoeconomic methodology is explained that allows to optimally size the plant, using the current prices of each technology. The most cost-competitive proposal turns to be the hybrid plant with thermal storage, composed by 623.9 MW installed power and 21.9 GWh of storage, which could replace a 100 MW, 24/7 conventional power plant, with an LCOHS (levelized cost of hybrid system) of 118.38 €/MWh, providing identical grid services and an equivalent inertia in a way committed with the environment. This is in turn a zero-carbon emissions solution perfectly matched to a second life plan for a conventional power plant., This work has been supported by Siemens Gamesa Renewable Energy, by the Spanish State Research Agency (AEI/ 10.13039/501100011033) under grants PID2019-111262RB-I00 and PID2019-110956RB-I00, and by the Public University of Navarra under project ReBMS PJUPNA1904.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Inertial response and inertia emulation in DFIG and PMSG wind turbines: emulating inertia from a supercapacitor-based energy storage system

  • Sacristán Sillero, Javier
  • Goñi Pérez, Naiara
  • Berrueta Irigoyen, Alberto
  • López Taberna, Jesús
  • Rodríguez Rabadan, José Luis
  • Ursúa Rubio, Alfredo
  • Sanchis Gúrpide, Pablo
The increasing wind power penetration in electrical power systems results in a reduction of operative conventional power plants. These plants include synchronous generators directly connected to the grid. Facing a change in grid frequency, these generators inherently respond by varying their stored kinetic energy and their output power, which contributes to grid stability. Such a response is known as inertial response. Wind turbines (WTs) are mostly based on Doubly-Fed Induction Generator (DFIG) or Permanent Magnet Synchronous Generator (PMSG) machines. Their power electronics interface decouples the electromechanical behaviour of the generator from the power grid, making their inertial response null or insignificant. Therefore, in order not to weaken the frequency response of the power system, WTs must be able to react to frequency variations by changing their output power, i.e., emulating an inertial response. Common techniques for inertia emulation in WTs rely on pitch control and stored kinetic energy variation. This contribution proposes a strategy (applicable for both DFIG and PMSG) which uses the energy stored in a supercapacitor connected to the back-to-back converter DC link to emulate the inertial response. Its performance is compared by simulation with aforementioned common techniques, showing ability to remove certain limitations., This work has been supported by Siemens Gamesa Renewable Energy, by the Spanish State Research Agency (AEI/ 10.13039/501100011033) under grants PID2019-111262RB-I00 and PID2019-110956RB-I00, and by the Public University of Navarra under project ReBMS PJUPNA1904
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Optimized DFIG electrical design under voltage sags

  • Urtasun Salinas, Ibai
  • Larrea León, Pablo
  • López Taberna, Jesús
This paper addresses the dual problem (electrical-mechanical) of DFIG-based wind turbines under voltage sags and proposes an optimized solution that, starting from a design aimed to mitigate the mechanical loads in the structural components of the wind turbine, provides the electrical capability to meet the most demanding grid codes., This work has been supported by the Spanish State Research Agency (AEI) under grant PID2019-110956RB-I00 /AEI/10.13039/501100011033
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

High-dynamics P-E and Q-f control of PV inverters for strong and weak grids

  • Urtasun Salinas, Ibai
  • Urtasun Erburu, Andoni
  • Marroyo Palomo, Luis
The increase of power electronic-based generators is causing the replacement of synchronous generators, which poses new challenges to electrical grid stability. In particular, when grid-following inverters are connected to weak grids, stability problems related to the PLL used for synchronization arise. To address this issue, grid-forming controls are widely proposed. However, the conventional implementations, such as droop control or virtual synchronous generator, lead to slow power controls, which are not suitable for photovoltaic systems with no storage. Thus, to improve the control dynamics, this paper proposes a new P-E and Q-f control. This control uses the reactive power for grid synchronization, avoiding the use of a PLL, and is valid for both inductive and resistive lines. Furthermore, thanks to the controller design developed in the paper, the control remains rapid and stable for very weak grids. Simulation results validates the control design and shows that the proposed control is much faster than the droop control for all types of grids., This work was supported by the Spanish State Research Agency (AEI) under grant PID2019-110956RB-I00/AEI/10.13039.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Dynamic modeling and simulation of a pressurized alkaline water electrolyzer: a multiphysics approach

  • Iribarren Zabalegui, Álvaro
  • Barrios Rípodas, Ernesto
  • Ibaiondo, Harkaitz
  • Sánchez Ruiz, Alain
  • Arza, Joseba
  • Sanchis Gúrpide, Pablo
  • Ursúa Rubio, Alfredo
In this paper a dynamic model for the simulation of pressurized alkaline water electrolyzers is presented. The model has been developed following a multiphysics approach, integrating electrochemical, thermodynamic, heat transfer and gas evolution processes in order to faithfully reproduce the complete dynamical behavior of these systems. The model has been implemented on MATLAB/Simulink and validated through experimental data from a 1 Nm3h-1 commercial alkaline water electrolyzer, and the simulated results have been found to be consistent with the real measured values. This model has a great potential to predict the behavior of alkaline water electrolyzers coupled with renewable energy sources, making it a very useful tool for designing efficient green hydrogen production systems., This work has been supported by the Spanish State Research Agency. (AEI/10.13039/501100011033) under grants PID2019-111262RB-I00 and PID2019-110956RB-I00, and by Ingeteam R&D Europe.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Asymmetrical firing angle modulation for 12-pulse thyristor rectifiers supplying high-power electrolyzers

  • Iribarren Zabalegui, Álvaro
  • Barrios Rípodas, Ernesto
  • Elizondo Martínez, David
  • Sanchis Gúrpide, Pablo
  • Ursúa Rubio, Alfredo
This paper presents an asymmetrical firing angle modulation strategy for 12-pulse thyristor rectifiers aimed at supplying high-power electrolyzers, which allows to reduce the size of the passive filter and the static compensator (STATCOM) required to comply with grid harmonic regulations and achieve unity power factor. Usually, 12-pulse thyristor rectifiers follow a symmetric modulation strategy in which the same firing angle is applied to both 6-pulse bridges. In this case, large passive ac-side inductances are required to reduce grid current harmonics, which increase the reactive power consumption and thus the required STATCOM size. However, this paper demonstrates that by applying different firing angles to the two 6-pulse bridges it is possible to comply with the harmonic regulation limits using smaller filtering inductances and therefore reducing the STATCOM size. The methodology to find the optimal firing angle values that should be applied in order to minimize the filtering inductance and the STATCOM size for a given electrolyzer is explained. This strategy is validated by simulation, and results show that the required filtering inductance and the apparent power of the STATCOM can be effectively reduced by 62% and 31%, respectively, using this asymmetrical firing angle modulation., This work is part of the projects PID2019-110956RB-I00 and TED2021-132604B-I00, funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR. It has also been supported by Ingeteam Power Technology.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Modeling the inherent damping of high-power inverters

  • Erdocia Zabala, Ioseba
  • Urtasun Erburu, Andoni
  • Marroyo Palomo, Luis
In order to decide whether passive or active damping is required in a three-phase inverter, a previous step is to assess the intrinsic damping of the system. However, few works focus on modeling this damping for DC/AC operation. This paper proposes two models to reproduce the damping sources: the simulation model, used to validate the system in large-signal, and the small-signal model, which can be employed for the controller design. Both models have been validated by means of experimental results for a 1.64 MVA inverter., This work was supported by the Spanish State Research Agency (AEI) under grants PID2019-110956RB-I00/AEI/10.13039 and DPI-2016-80641-R, and by the Public University of Navarre through a doctoral scholarship.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Active control for medium-frequency transformers flux-balancing in a novel three-phase topology for cascaded conversion structures

  • Lumbreras Magallón, David
  • Barrios Rípodas, Ernesto
  • Navarrete, Manuel
  • Balda Belzunegui, Julián
  • González Senosiain, Roberto
  • Sanchis Gúrpide, Pablo
Efficiency and power density are important parameters in the design of power electronics converters. In many applications, low-frequency transformers are being substituted for medium-frequency and high-frequency transformers in order to reduce the volume and therefore the cost of the transformer. However, preventing their saturation is a complex task. This paper studies the medium-frequency transformers' flux balancing in a novel three-phase topology for cascaded conversion structures.Based on the modulation technique of the converter, a method to directly measure the magnetizing current of the medium-frequency transformers is proposed in this paper. A control loop to regulate the dc value of the magnetizing current is also designed and developed. Simulation results validate the correct operation of the control loop, which prevents the transformer saturation., This work was supported by the Spanish State Research Agency (AEI) under grants PID2019-110956RB-I00 /AEI/ 10.13039/501100011033 and DPI-2016-80641-R, and by the Public University of Navarre through a doctoral scolarship.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Zero-loss switching in DC-DC series resonant converters under discontinuous conduction mode

  • Elizondo Martínez, David
  • Barrios Rípodas, Ernesto
  • Sanchis Gúrpide, Pablo
Many thriving applications where isolation is required, such as traction and EV fast charging, implement solid-state transformers (SST). Half-cycle discontinuous-conduction-mode series resonant converters (HC-DCM-SRC) are suitable for these applications. The focus of this paper is to perform a comprehensive approach to HC-DCM-SRC and provide straight-forward requirements in order to ensure zero-loss switching (ZLS) of semiconductors. In addition, these requirements can be expressed as design boundaries for the transformer. Finally, the paper shows that, due to ZLS, silicon devices may have larger power capability than silicon-carbide switches. Therefore, IGBTs can be used instead of SiC MOSFETs, resulting in a significant cost reduction of the converter., This work was supported by the Spanish State Research Agency (AEI) under grant PID2019-110956RB-I00 and by the Public University of Navarre (UPNA) under a PhD scholarship
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Capacitor current feedback active damping with lagged compensator for DFIG wind turbines with LCL filter

  • Rosado Galparsoro, Leyre
  • Samanes Pascual, Javier
  • Gubía Villabona, Eugenio
  • López Taberna, Jesús
Several active damping strategies have been proposed in the literature for grid-connected converters with LCL filter but there are not specific strategies for DFIG wind turbines. In this system, there is an interaction between the two converters of the back-to-back conversion structure, which must be properly modeled in order to design effective damping strategies for the LCL filter resonant poles. This paper proposes a robust active damping strategy for DFIG wind turbines with LCL filter that considers the special features of this system. In this technique the filter capacitor current is fed back through a lag compensator that adjusts the delay of the feedback loop to emulate a virtual impedance that has dominant resistive behavior in the range of possible resonance frequencies. It is shown that a similar damping of the LCL filter resonance is achieved when the strategy isimplemented in either of the two converters., This work was supported by the Spanish State Research Agency (AEI) under grants PID2019-110956RB-I00 /AEI/10.13039 and DPI-2016-80641-R.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Analytical modeling of high-frequency winding loss in round-wire toroidal inductors

  • Elizondo Martínez, David
  • Barrios Rípodas, Ernesto
  • Sanchis Gúrpide, Pablo
  • Ursúa Rubio, Alfredo
Toroidal inductors are present in many different industrial applications, thus, still receive researchers' attention. AC winding loss in these inductors have become a major issue in the design process, since switching frequency is being continuously increased in power electronic converters. Finite element analysis software or analytical models such as Dowell's are the main existing alternatives for their calculation. However, the first one employs too much time if different designs are to be evaluated and the second one lacks accuracy when applied to toroidal inductor windings. Looking for an alternative that overcomes these drawbacks, this paper proposes an accurate, easy-to-use analytical model, specifically formulated for calculating high-frequency winding loss in round-wire toroidal inductors., This work was supported by the Spanish State Research Agency (AEI) under grants PID2019-110956RB-I00/AEI/10.13039 and DPI-2016-80641-R.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Toroidal inductor design in multilevel DC-DC electric vehicle battery charger including high-frequency effects

  • Elizondo Martínez, David
  • Barrios Rípodas, Ernesto
  • Sanchis Gúrpide, Pablo
Inductor filters, such as the ones implemented in DC-DC buck-boost converters for electric vehicle chargers, have a major impact on the converter weight, volume and cost. Thus, their design is key in order to obtain an optimal design of the whole converter. This paper proposes a design methodology for powder core toroidal inductors, which is based on a holistic approach of the design of the inductor, where losses due to highfrequency effects are computed by means of specific loss model for toroidal windings, and saturation, geometrical and thermal constraints are considered. The convenience of the design tool is shown through an analysis over a wide variation of parameters, including converter topology, parallelization, switching frequency and inductance. The analysis demonstrates the relevance of high-frequency effects on the inductor design, so certain misconceptions can be avoided, such as that the inductor volume monotonically decreases when the inductance value is decreased or that paralleling inductors always results in more compact designs. A design example is presented for a 15-kW, three-level electric vehicle battery charger. The algorithm is used to obtain an optimal design of the converter, including the inductors and SiC MOSFET devices. Finally, an easy method to obtain a commercial inductor design from the theoretical one provided by the algorithm is presented., This work was supported by the Spanish State Research Agency (AEI) under grant PID2019-110956RB-100 and by the Public University of Navarre (UPNA) under a PhD scholarship.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

DC capacitance reduction in photovoltaic inverters based on PV voltage feed-forward compensation

  • Urtasun Erburu, Andoni
  • Sanchis Gúrpide, Pablo
  • Marroyo Palomo, Luis
In the case of photovoltaic (PV) inverters, an adequate input voltage regulation is fundamental to maximize or limit the power. When employing the traditional control, the input capacitance requires to be oversized in order to reduce the influence of the PV generator and achieve a stable control in the whole operating point. This paper proposes a voltage control method which permits reducing the capacitance by a factor of 5, thereby reducing the system cost. The control includes a feed-forward compensation of the PV voltage, making it possible to achieve a fast and stable control with a simple implementation. The proposed method is verified by simulation, showing the problems of the traditional control and the superior performance of the proposed control., This work was supported by the Spanish State Research Agency (AEI) under grant PID2019-110956RB-I00/AEI/10.13039.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Small-signal stability analysis of power converters with optimal pulsewidth modulation strategies

  • Rosado Galparsoro, Leyre
  • Samanes Pascual, Javier
  • López Taberna, Jesús
  • Gubía Villabona, Eugenio
Optimal pulsewidth modulation strategies are commonly used in power electronics applications with closed-loop controllers. However, there is a lack of specific studies in the literature that analyze and study the dynamics of these modulators, which makes it difficult to derive small-signal models for stability analysis and controller design. Moreover, in many studies, the influence of optimal pulsewidth modulation on the small-signal stability analysis is disregarded. This article addresses these issues by proposing a modeling methodology for optimal pulsewidth modulators, applied to a selective harmonic elimination modulator. The proposed methodology is based on the frequency response analysis, which is particularly convenient for controller design. The study shows that the classical zero-order hold model employed for carrier-based pulsewidth modulators is valid for characterizing the dynamics of optimal pulse-width modulation strategies. Simulation results validate this conclusion., This work is part of the projects PID2019-110956RB-I00 and TED2021-132604B-I00, funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGenerationEU/PRTR. It has also been partially supported by Ingeteam Power Technology and the Public University of Navarre.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

On the technical reliability of lithium-ion batteries in a zero emission polar expedition

  • Soto Cabria, Adrián
  • Berrueta Irigoyen, Alberto
  • Sanchis Gúrpide, Pablo
  • Ursúa Rubio, Alfredo
  • Oficialdegui, Ignacio
This contribution presents a technical analysis of the Lithium-ion batteries (LIBs) used in the WindSled project. In this project, an expedition has been carried out by means of a 0-emission vehicle that have covered more than 2500 kilometers in Antarctica Eastern Plateau pulled by kites. This adventure allowed the performance of 10 scientific experiments with a minimal disturbance of the polar environment. The required electricity for the survival and the scientific experimentation was delivered by flexible PV panels installed on the sled and commercial LIBs. The study performed in this contribution aims at the quantification of the LIBs degradation after the expedition. The results show a capacity fade of 5 % and an internal resistance increase of 30 %. Based on these results, it can be claimed that the LIBs used in the WindSled Project can successfully operate under -40°C. Moreover, these batteries can be used in upcoming expeditions, entailing an improvement from an economical and environmental point of view compared to primary batteries., Spanish State Research Agency (AEI) and FEDER-UE under grants DPI2016-80641-R, DPI2016-80642-R, PID2019-111262RB-I00 and PID2019-110956RB-I00, the Government of Navarra through research project 0011-1411-2018- 000029 GERA and the Public University of Navarre under project ReBMS PJUPNA1904.