Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

New low carbon footprint cement-lime mortar with phase change materials (PCM) and biomass ash for thermal enhancement of buildings

  • Guardia Martín, Cynthia|||0000-0003-4442-8933
  • Guerrero Gil, Ana
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
  • Ramallo Aznar, Laura|||0000-0003-3822-6868
  • Palomar Herrero, Irene|||0000-0003-2743-3618
Many studies focus on new advanced materials, such as Phase Change Materials (PCMs), to fulfill the increasing requirements for energy efficiency set by the European Commission. PCM have demonstrated thermal properties enhancement as thermal accumulators regarding to other traditional building materials, due to their heating storage capacity. Besides, it is necessary to reduce carbon footprint of plasters and renderings and replacing cement by lime and biomass ashes emerges as a potential solution. This work presents an experimental study on the physical, mechanical and thermal properties of low carbon footprint cement-lime mortars with the addition of PCM (10% and 20%) and the replacement of cement by biomass ashes (10% and 20%). Thermal performance was assessed on mortar pastes, using Differential Scanning Calorimetry, and on mortar samples under different environmental conditions in a climate chamber. The results showed the influence of the addition of PCM on physical and mechanical mortars’ properties, as well as their thermal performance, increasing mortar energy storage capacity. Partial replacement of cement by biomass ash slightly reduced thermal enhancement. It was observed that paste results could be related to mortars properties, which pointed out that paste phase design can be used to obtain target mortar properties., Comisión Europea (Fondos Next Generation), Universidad de Alcalá, Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Rheological and 3D printing assessment of sisal fiber mortar for architectural applications

  • Varela Recio, Hugo|||0000-0001-8094-6071
  • Pimentel Tinoco, Matheus
  • Mendoza Reales, Óscar Aurelio
  • Toledo Filho, Romildo Dias
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
3D printing mortars are becoming a focus of interest for architectural applications, due to their ability to produce free shaping designs. However, there are still some printability and performance issues that require further research, as the incorporation of reinforcing and the improvement of sustainability by reducing its carbon footprint. Natural fibers become an excellent alternative to overcome these problems, enhancing mortar performance. The aim of this study was to evaluate rheology and printability of mortars with sisal fibers (SF) for architectural 3D printing applications. A reference cement mortar with 0-0.6 mm sand and 0.45 water to cement ratio was designed. Then, 13 mm length SF in volumetric fractions (VF) of 0.5, 1 and 1.5%, and 6.5 mm length SF at 1%VF were added. Four tests were carried out to evaluate fresh rheological and mechanical properties of mortars: flow table test, self-weight cone- penetration test, displacement-controlled conepenetration test and uniaxial fresh compression test. Mortar printability was evaluated with a manual extruder and a 3D robotic printer, reaching an open time window of 90 minutes. It was observed that 3D printing produced an alignment of SF. Larger SF amount gradually increased initial yield stress and structural build up. The VF and length of SF maintained initial compressive yield stress, enhancing tenacity of fresh material. Mortars with low VF of SF showed good printability, although higher SF VF produced some printing issues due to their lower pumpability., Comisión Europea (Fondos Next Generation), Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Fresh and hardened properties of cellulose fiber-reinforced mortars for 3D printing in construction

  • Pimentel Tinoco, Matheus
  • Márquez Martín, Álvaro|||0000-0001-8554-9614
  • Ramallo Aznar, Laura|||0000-0003-3822-6868
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
  • Mendoza Reales, Óscar Aurelio
  • Dias Toledo Filho, Romildo
With the ongoing advancement of 3D printing technology in the construction sector, the requirement for materials with optimized fresh and mechanical properties is becoming more critical. Natural fiber-reinforced mortars can be an effective solution by enhancing material?s printability. This work evalu-ates the effect of cellulose microfibers (CF) on fresh and hardened proper-ties of 3D printable mortars. A reference mortar was prepared with 0-1 mm sand and 0.4 water-to-cement ratio, and three volumetric fractions of fibers were used: 2.5, 7.5, and 12.5 % by mortar volume. Fresh-state properties were studied using flow table and fresh compression tests. Physical and me-chanical tests were also conducted to assess the effect of fibers on the hard-ened state properties. A robotic 3D printer was used to assess mortar printa-bility. Fresh state results demonstrated that CF significantly increased rheo-logical properties over time, enhancing thixotropic behavior. 3D printing tests showed that CF improved buildability, although limited extrudability and shortened the printing open time. Additionally, CF increased 28-days me-chanical strength of mortars; however, they also enlarged capillary water ab-sorption, which could impact durability. The results underscore the potential of CF to modulate fresh and hardened mechanical properties of 3D printable mortars for construction applications., Comisión Europea (Fondos Next Generation)
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Experimental thermal evaluation of multilayer 3D printed architectural enclosures made of lime-cement mortars with PCM and Cellulose Fibers

  • Ramallo Aznar, Laura|||0000-0003-3822-6868
  • Márquez Martín, Álvaro|||0000-0001-8554-9614
  • Palomar Herrero, Irene|||0000-0003-2743-3618
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
The reduction of carbon footprint towards sustainability in the con-struction sector demands innovative construction techniques and novel and bio-based building materials to optimize the building process and make it more sus-tainable. This study evaluates experimentally the dynamic thermal performance on hardened lime-cement mortars with Phase Change Materials (PCM) and Cel-lulose Fibers (CF) for 3D printing applications. Four material?s design strategies were followed to reduce carbon footprint: partial substitution of cement by air-lime, addition of a Phase Change Material (PCM) to increase thermal energy ef-ficiency, nanoclays to improve material printability and Cellulose Fibers (CF) to enhance extrudability and enlarge durability. A mortar mixture with 20% of PCM was selected to produce three types of specimens: cast in the mold plate, 3D-printed plate and 3D-printed truss. A multilayer enclosure system with a thermal insulation layer plus a mortar specimen was tested using a climate chamber to simulate dynamic cooling and heating cycles, ranging 15 - 30ºC. The experi-mental results showed that the manufacturing procedure did not modify the high thermal efficiency of the material, while a truss cross-section element largely in-creased energy efficiency of the enclosure system., Universidad de Alcalá, Comisión Europea (Fondos Next Generation), Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Use of Bio-Carbon Fibers for self-sensing cement-based composites for Structural Health Monitoring

  • Puentes Mojica, Javier|||0000-0001-8748-7664
  • Palomar Herrero, Irene|||0000-0003-2743-3618
  • Lopesino Cerqueira, Yaiza
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
The use of functionalized components in cement-based composites (CBC) is an innovative way to provide novel material?s capabilities. Carbon-based ad-ditions and fibers can modify electrical properties of CBC, such as piezore-sistivity (PZR). PZR enables a new intrinsic capacity of CBC, relating the variation of material?s electrical resistance to material?s stress when subjected to external loads, successfully transforming CBC into a self-sensing material that can be used for Structural Health Monitoring (SHM). This study aims to evaluate the use of carbon fibers of biological sources (CF-BIO), obtained from lignin as raw material, which is a sustainable alter-native to petroleum carbon fibers (CF-PAN), due to its natural origin and lower environmental impact. Fiber content required for achieving PZR ca-pacity of CBC has been already defined for CF-PAN. The variation of elec-trical and piezoresistive properties as an effect of self-sensitive capacity were tested. These measurements were be used to calculate the fractional change resistivity (FCR) and the sensitivity rate of the material (Csens)., Agencia Estatal de Investigación, Ministerio de Ciencia, Innovación y Universidades, Comisión Europea (Fondos Next Generation)
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Thermal evaluation of low-carbon lime cement mortars with PCM for 3D printing architectural applications

  • Ramallo Aznar, Laura|||0000-0003-3822-6868
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
  • Palomar Herrero, Irene|||0000-0003-2743-3618
The design of innovative low-carbon and energy efficient building materials and technologies are on the basis to construction and architecture sustainability. New lime-cement mortars with microencapsulated Phase Change Material (PCM) for 3D printing architectural applications were designed and experimentally evaluated to collaborate into achieving this goal. The innovation comes through integrating three strategies: reducing carbon footprint and embodied energy by partially replacing ordinary Portland Cement (OPC) by lime; enhancing energy efficiency and storage capacity by incorporating microencapsulated PCM; improving printability and buildability for 3D printing architectural enclosures by using rheology modifiers. Eight lime-cement mortars with PCM, Cellulose Fibers (CF) and rheology modifiers, nanoclays and organic VMAs, were designed and characterized in fresh and hardened state to led to an innovative building technology regarding conventional architectural facades. Hardened thermal properties were evaluated by Differential Scanning Calorimetry (DSC) and on reduced scale experimental simulations applying cooling and heating cycles on mortar plate samples using a climate chamber. Hardened mechanical properties were also tested to evaluate compressive and flexural strength. PCM boosted mortars’ thermal performance, improving mass enthalpy up to 60%, while CF slightly attenuated this reduction. Accordingly, PCM lime-cement mortars showed excellent fresh properties to be used for 3D printing digital fabrication in architectural applications, and CF along with rheology modifiers enhanced buildability and thixotropy both in initial and set up times. This study’s main focus is on the mortars’ physical, mechanical and thermal properties., Universidad de Alcalá, Comisión Europea (Fondos Next Generation), Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación