Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

New low carbon footprint cement-lime mortar with phase change materials (PCM) and biomass ash for thermal enhancement of buildings

  • Guardia Martín, Cynthia|||0000-0003-4442-8933
  • Guerrero Gil, Ana
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
  • Ramallo Aznar, Laura|||0000-0003-3822-6868
  • Palomar Herrero, Irene|||0000-0003-2743-3618
Many studies focus on new advanced materials, such as Phase Change Materials (PCMs), to fulfill the increasing requirements for energy efficiency set by the European Commission. PCM have demonstrated thermal properties enhancement as thermal accumulators regarding to other traditional building materials, due to their heating storage capacity. Besides, it is necessary to reduce carbon footprint of plasters and renderings and replacing cement by lime and biomass ashes emerges as a potential solution. This work presents an experimental study on the physical, mechanical and thermal properties of low carbon footprint cement-lime mortars with the addition of PCM (10% and 20%) and the replacement of cement by biomass ashes (10% and 20%). Thermal performance was assessed on mortar pastes, using Differential Scanning Calorimetry, and on mortar samples under different environmental conditions in a climate chamber. The results showed the influence of the addition of PCM on physical and mechanical mortars’ properties, as well as their thermal performance, increasing mortar energy storage capacity. Partial replacement of cement by biomass ash slightly reduced thermal enhancement. It was observed that paste results could be related to mortars properties, which pointed out that paste phase design can be used to obtain target mortar properties., Comisión Europea (Fondos Next Generation), Universidad de Alcalá, Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Early age and hardened properties of 3D printable cement-lime mortars with microencapsulated PCM and cellulose microfibers

  • Ramallo Aznar, Laura|||0000-0003-3822-6868
  • Márquez Martín, Álvaro|||0000-0001-8554-9614
  • Palomar Herrero, Irene|||0000-0003-2743-3618
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
The design of sustainable functionalized materials suitable for new building technologies has become a challenge for the construction sector. In this study, 3D printable cement-lime mortars incorporating microencapsulated phase change material (PCM) and cellulose microfibers (CMF) were designed and experimentally characterized considering the requirements for architectural applications. The use of lime aims to reduce environmental impact, PCM intends to enhance thermal performance and CMF to provide early age integrity. Two reference mortars were designed, with and without CMF, and PCM was incorporated at 10, 20 and 30% into both reference mixtures. An experimental program was carried out evaluating mortars’ fresh state rheological properties, early age performance and short- and long-term hardened-state physical, thermal and mechanical properties. Long- term carbonation was also assessed. The experimental approach provided a comprehensive understanding of how these components interact across all relevant stages of material development, from fresh state to long-term performance. Lime densified mortar matrix, due to carbonation, contributing to strength gain and reducing water absorption. PCM improved thermal behavior by enhancing their energy storage capacity up to a 35 – 40%, while CMF mitigated early age setting delays in mixtures containing PCM but reduced the thermal storage enhancement at PCM contents above 20%., European Commission, Junta de Castilla-La Mancha
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Piezoresistivity in self-compacting concrete mixes with hybrid additions of carbon fibers and nanofibers

  • Puentes Mojica, Javier|||0000-0001-8748-7664
  • Palomar Herrero, Irene|||0000-0003-2743-3618
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
SMARTINCS"23 Conference on Self-Healing, Multifunctional and Advanced Repair Technologies in Cementitious Systems, Self-sensing properties of concrete structures can be achieved through the incorporation of additions in carbon-based materials (CBM) that modify electrical properties and provide piezoresistive (PZR) properties to the cement paste. PZR in pastes and mortar mixes with different types of carbon-based materials such as fibers of different sizes has been extensively tested. However, very limited studies on selfsensing properties in concrete are available due to the lower content of paste volume that leads to a decrease of concrete PZR. However, self-compacting concrete (SCC) can be an ideal candidate to implement PZR, due to two fundamental traits: the larger amount of paste of SCC compared to a conventional concrete and larger volumetric fraction of fiber can be incorporated due to a reduced effect on SCC workability and consistency. The present study aims to assess PZR properties of SCC with carbon-based components of different sizes. Combining carbon nanofibers (NFC) and carbon fibers (CF), in hybrid systems, could lead to obtain SCC with self-sensing properties identifying their effectiveness thresholds. The self-detection performance of PZR-SCC samples under mechanical stress was verified by resistivity and PZR experimental tests., Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación, Comisión Europea, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Biomass ash and phase change material (PCM) for energy efficiency of sustainable cement-lime composites

  • Guardia Martín, Cynthia|||0000-0003-4442-8933
  • Guerrero Bustos, Ana
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
Sustainability and nearly zero-energy consumption of new and existing buildings is a keystone in the new guidelines established by the European Commission. Likewise, waste management is in the focus of reducing the impact of industrial processes. The use of industrial byproducts, such as biomass ashes (BA), can be an interesting solution for waste valorization, reducing the carbon footprint and enhancing sustainability. In addition, Phase Change Materials (PCMs) can be used for improving energy efficiency due to their thermal storage capacity. An experimental study on the effect of biomass ash (BA) and PCM on the microstructure, chemical, physical and mechanical properties of cement–lime pastes was carried out. The partial replacement of cement with BA reduced compressive strength although did not substantially modify other paste properties, while the addition of PCM had a huge impact on microstructure and, therefore, physical and mechanical properties. PCM had a remarkable effect on thermal properties, endowing thermal storage capacity and reducing thermal conductivity, and the combination with BA further improved paste thermal properties., Comisión Europea (Fondos Next Generation)
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Rheology characterization of 3D printing mortars with nanoclays and basalt fibers

  • Varela Recio, Hugo|||0000-0001-8094-6071
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
  • Sonebi, Mohammed
3D printing has become one of the most innovative technologies for cement-based systems (CBS). However, recent studies have shown some issues related to printability and buildability (water drainage, plugs on extruder die, spreading of first layer, etc). To achieve a proper rheology control of CBS, it is essential to adapt the material fresh state properties (initial shear yield stress and structural build-up). In this study, a reference cement-based mortar with fly ash (25%), a 1:1.5 binder to sand ratio and a 0.38 water to binder ratio was used. A polycarboxilate ether-based superplasticizer was added until a consistency of around 1 kPa, measured with the cone-penetration test, was reached. Then, small amounts of several types of nanoclays (NC) in powder and slurry form (sepiolite, attapulgite and bentonite) and natural fibers were added to modify mortar rheological properties. The aim of the study was to characterize the rheological properties of 3D printing mortar samples with NC and basalt fibers (BF) to understand printability and buildability of this material. Cone-penetration test, flow table test and slump test were used to characterize 3D printing capacities. The cone-penetration test was performed in stirred and left at rest samples to assess shear yield stress before and after material deposition. Nanoclays showed a remarkable capacity to retain water and avoid drainage during extrusion but also to increase fresh state strength of material over time. Besides, they increased shear yield stress over time when left at rest. On the contrary, samples stirred over time did not show any increase of shear yield stress, especially samples with slurry nanoclays. Natural fibers also reduced drainage and enhance printability control regarding to reference mortar. BF also enhanced a performance on stirred sample but showed slightly changes on structural build-up at rest, mainly governed by NC effect., Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación, Comisión Europea, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Experimental results and numerical analysis of capillary water absorption of lime-cement mortars with PCM and cellulose fibres for 3DP applications

  • Ramallo Aznar, Laura|||0000-0003-3822-6868
  • Caggiano, Antonio
  • Palomar Herrero, Irene|||0000-0003-2743-3618
  • Márquez Martín, Álvaro|||0000-0001-8554-9614
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
Artículos completos del congreso MECOM 2025, This study assesses the moisture transport phenomena of 3D printing lime-cement mortars with Phase Change Materials (PCM) and Cellulose Fibers (F) for architectural applications comparing experimental results and numerical analyses. A lime-cement control mortar was designed and cellulose fibers and different percentages of PCM (i.e., 10, 20 and 30%) were added, leading to a total of eight different mixtures. Physical and mechanical characterization tests were performed on mortar samples and capillary water absorption tests were carried out over 24h. Based on the experimental results, a computational nonlinear FE-based Moisture Diffusion model was calibrated to simulate the data., Comisión Europea (Fondos Next Generation), Agencia Estatal de Investigación
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

3D Printing Architectural Applications of cement-lime mortars with microencapsulated Phase Change Materials (PCM)

  • Márquez Martín, Álvaro|||0000-0001-8554-9614
  • Ramallo Aznar, Laura|||0000-0003-3822-6868
  • Varela Recio, Hugo|||0000-0001-8094-6071
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
  • Puentes Mojica, Javier|||0000-0001-8748-7664
3D printing technology arouses great interest for its application in architecture on facades and building enclosures that still need to be explored. An experimental study of 3D printing laboratory prototypes using low-carbon ce- ment-lime mortars with microencapsulated Phase Change Material (PCM) was carried out to evaluate its application for adaptative building enclosures. Rheology, extrudability and buildability of PCM cement-lime mortars were assessed. Cellulose fibers and rheology modifiers, as sepiolite nano-clay, were used to enhance mortar properties. Rheological parameters were measured using a Dynam- ic Shear Rheometer (DSR) and Cone Penetration Test (CPT) in fresh state. Fresh compressive strength evolution was assessed by fresh compressive strength test (Squeeze Test) and Early Age monitoring was carried out to keep track of cement hydration and structural build up progress. Extrudability and buildability of mixtures were evaluated by means of RAM Extrusion Test and laboratory 3D printing prototype. This approach provided new knowledge on the design of high thermal performance mortars using digital fabrication in architectural ap- plications, contributing to the digitalization and sustainability of construction and building practice., Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación, Comisión Europea (Fondos Next Generation), Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Experimental thermal evaluation of multilayer 3D printed architectural enclosures made of lime-cement mortars with PCM and Cellulose Fibers

  • Ramallo Aznar, Laura|||0000-0003-3822-6868
  • Márquez Martín, Álvaro|||0000-0001-8554-9614
  • Palomar Herrero, Irene|||0000-0003-2743-3618
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
The reduction of carbon footprint towards sustainability in the con-struction sector demands innovative construction techniques and novel and bio-based building materials to optimize the building process and make it more sus-tainable. This study evaluates experimentally the dynamic thermal performance on hardened lime-cement mortars with Phase Change Materials (PCM) and Cel-lulose Fibers (CF) for 3D printing applications. Four material?s design strategies were followed to reduce carbon footprint: partial substitution of cement by air-lime, addition of a Phase Change Material (PCM) to increase thermal energy ef-ficiency, nanoclays to improve material printability and Cellulose Fibers (CF) to enhance extrudability and enlarge durability. A mortar mixture with 20% of PCM was selected to produce three types of specimens: cast in the mold plate, 3D-printed plate and 3D-printed truss. A multilayer enclosure system with a thermal insulation layer plus a mortar specimen was tested using a climate chamber to simulate dynamic cooling and heating cycles, ranging 15 - 30ºC. The experi-mental results showed that the manufacturing procedure did not modify the high thermal efficiency of the material, while a truss cross-section element largely in-creased energy efficiency of the enclosure system., Universidad de Alcalá, Comisión Europea (Fondos Next Generation), Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Extrusion and structural build-up of 3D printing cement pastes with fly ash, nanoclays and VMAs

  • Varela Recio, Hugo|||0000-0001-8094-6071
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
  • Perrot, Arnaud
3D printing technology (3DP) has provided new design and structural opportunities for cement-based systems (CBS) in architectural construction. However, there are still some issues related to extrudability and buildability of CBS, which can be overcome by using components for CBS rheology control. In this study, three types of nanoclays, a bentonite (BEN), a sepiolite (SEP) and an attapulgite (ATT), and two viscosity modifying admixtures (VMAs), a poly-acrylamide (VMA1) and a methylcellulose ether (VMA2), were added to a reference cement-fly ash 3D printing paste to evaluate their impact on CBS rheological properties and their implications in extrusion and buildability for 3DP. A polycarboxylate-ether based high range water-reducing admixture (HRWRA) was used to reach a target stiff consistency. Four laboratory tests were used to assess paste rheology, extrusion and structural build-up. Proper and deficient material extrusion limits were defined considering cohesion and initial yield stress. It was found that the combination of VMA2 and SEP increased cohesion, enhancing extrusion and avoiding water drainage and frictional behavior of pastes, producing properly extrudable paste. SEP by itself also improved structural build-up. Besides, samples with NC and VMAs required larger amounts of HRWRA, delaying cement setting and compressive strength gain., Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación, Comisión Europea, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Piezoresistive self-compacting concretes (PSSC) with carbon fibers (CF) and nano-fibers (CNF) for structural health monitoring

  • Puentes Mojica, Javier|||0000-0001-8748-7664
  • Palomar Herrero, Irene|||0000-0003-2743-3618
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
Real-time monitoring of structural health is a key issue for structural safety. Monitoring systems have evolved from external devices into intrinsic selfdetection systems (SDS) becoming diagnostic and monitoring tools useful to maintain and increase structural durability. Furthermore, SDS are an economical and efficient solution for using human and technical resources towards sustainability. Self-sensing materials are considered a promising SDS technology to replace integrated connected or embedded systems, which have many limitations. Self-compacting concrete (SCC) is an advanced material that can become a self-sensing concrete by the incorporation of carbon-based materials, which provide the concrete matrix with piezoresistivity properties, transforming the material into a sensor by itself. The advantage of using SCC lies in its larger paste content which allows the use of hybrid systems of carbon-based additions, such as carbon nanofibres (CNF) and carbon fibres (CF). This combination can produce a synergistic response, improving the properties that can be achieved by incorporating each of them separately. Through the integration of electrical and piezoresistive properties, Piezoresistivity-SSC (PSCC) can collect real-time state variation information relating mechanical responses to piezoresistivity. The aim of this study was to identify the threshold of the effective admixtures content maintaining acceptable workability and achieving PSSC self-sensitivity., Comisión Europea (Fondos Next Generation)
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Printability assessment of 3D printing cement-lime mortars with microencapsulated PCM

  • Márquez Martín, Álvaro|||0000-0001-8554-9614
  • Ramallo Aznar, Laura|||0000-0003-3822-6868
  • Palomar Herrero, Irene|||0000-0003-2743-3618
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
An experimental study was conducted to evaluate the printability of cement–lime mortars designed for 3D printing applications, incorporating a microencapsulated phase-change material (PCM) and cellulose microfibers (CMFs). The influence of both PCM and CMFs on mortars’ rheology was measured by rheometer tests (DSR) and cone penetration tests (CPT). A ram extrusion test was used to evaluate the extrudability, and an unconfined uniaxial compression test (UUCT) allowed the assessment of buildability. Finally, several lab-scale prototypes were 3D-printed. The results showed that the incorporation of PCM affected mortar’s rheology and workability due to the reduction in paste volume and the increase in superplasticizer (SP) demand. However, the spherical particle shape of microencapsulated PCM was found to ease the extrusion process. After being extruded, mortars with lower volumetric fractions of PCM exhibited increased fresh strength and stiffness, whereas larger amounts reduced both parameters. The use of CMFs considerably reduced the extrusion force and improved the extrusion quality. Lab-scale 3D-printed prototypes were successfully manufactured using mortars with a 20% volumetric fraction of PCM., European Commission, Junta de Comunidades de Castilla-La Mancha
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Thermal evaluation of low-carbon lime cement mortars with PCM for 3D printing architectural applications

  • Ramallo Aznar, Laura|||0000-0003-3822-6868
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
  • Palomar Herrero, Irene|||0000-0003-2743-3618
The design of innovative low-carbon and energy efficient building materials and technologies are on the basis to construction and architecture sustainability. New lime-cement mortars with microencapsulated Phase Change Material (PCM) for 3D printing architectural applications were designed and experimentally evaluated to collaborate into achieving this goal. The innovation comes through integrating three strategies: reducing carbon footprint and embodied energy by partially replacing ordinary Portland Cement (OPC) by lime; enhancing energy efficiency and storage capacity by incorporating microencapsulated PCM; improving printability and buildability for 3D printing architectural enclosures by using rheology modifiers. Eight lime-cement mortars with PCM, Cellulose Fibers (CF) and rheology modifiers, nanoclays and organic VMAs, were designed and characterized in fresh and hardened state to led to an innovative building technology regarding conventional architectural facades. Hardened thermal properties were evaluated by Differential Scanning Calorimetry (DSC) and on reduced scale experimental simulations applying cooling and heating cycles on mortar plate samples using a climate chamber. Hardened mechanical properties were also tested to evaluate compressive and flexural strength. PCM boosted mortars’ thermal performance, improving mass enthalpy up to 60%, while CF slightly attenuated this reduction. Accordingly, PCM lime-cement mortars showed excellent fresh properties to be used for 3D printing digital fabrication in architectural applications, and CF along with rheology modifiers enhanced buildability and thixotropy both in initial and set up times. This study’s main focus is on the mortars’ physical, mechanical and thermal properties., Universidad de Alcalá, Comisión Europea (Fondos Next Generation), Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Evaluation of basalt fibers and nanoclays to enhance extrudability and buildability of 3D-printing mortars

  • Varela Recio, Hugo|||0000-0001-8094-6071
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
  • Sonebi, Mohammed
A study of the rheological and fresh mechanical properties of fly ash-cement 3D printing (3DP) mortars with six types of nanoclays (NC) as rheology modifiers, two sepiolites, three attapulgites and one bentonite, and reinforced with short basalt fibers (BF) was carried out. Fresh mortar properties were evaluated with a flow table test (FTT), cylindrical slump test (CST) and conepenetration test (CPT) on samples left at rest and stirred before testing. Squeeze test (SQT) was carried out on samples cast-in-the-mold and 3D printed to compare the effects of 3DP on the fresh mechanical behavior. Extrudability was assessed with an electrical barrel extrusion device. NC and BF enhanced mortar cohesion by preventing water drainage and improving material extrudability. NC increased shear yield stress (tau₀) over time on samples left at rest, enhancing reversible thixotropy. Besides, NC required larger amounts of superplasticizer, increasing open time windows. Among NC, Sepiolite in powder form showed the best fresh mechanical perfor- mance on 3DP samples. BF enhanced extrudability due to the bridging effect but also shows mechanical synergies with some NC. 3DP samples showed lower compressive yield stress and Young modulus evolution over time (sigma˙ and E˙ ) than cast-in-the-mold samples, due to their layered structure., Universidad de Alcalá, Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación, Comisión Europea (Fondos Next Generation)