Pasar al contenido principal

CONTROL REOLOGICO Y MONITORIZACION A EDADES TEMPRANAS DE SISTEMAS CEMENTANTES NANOMODIFICADOS DISEÑADAS PARA LA IMPRESION EN 3D

PID2019-106525RB-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2019
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE ALCALA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Lateral pressure of nano-engineered SCC combining nanoclays, nanosilica and viscosity modifying admixtures

  • Varela Recio, Hugo|||0000-0001-8094-6071
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
  • Puentes Mojica, Javier|||0000-0001-8748-7664
  • Palomar Herrero, Irene|||0000-0003-2743-3618
  • Rodríguez López, Ángel José Alfredo
Self-compacting concrete (SCC) is an energy efficient building technology widely used for multiple constructive applications. However, the large flowability of fresh SCC produces an increase of the lateral pressure exerted on the formwork regarding to conventional concretes. One solution to reduce the maximum lateral pressure (Pmax) is to modulate the fresh performance of SCC by the addition of rheology modifiers. Among them, nanocomponents highlight due to their larger efficiency derived from their tiny particle size. In this study, the efficiency of nano-engineered SCC (NE-SCC) combining small amounts of nanocomponents, as nanoclays and nanosilica, with viscosity modifying admixtures (VMAs) to decrease Pmax is explored. Lateral pressure exerted by NE-SCC on cylindrical columns subjected to self-weight and to air pressure was assessed using wall and capillary pressure sensors over time. It was found that the incorporation of attapulgite and bentonite nanoclays combined with VMAs could reduce Pmax. This reduction was measured with wall and capillary pressure sensors on self-weight column and air pressure column laboratory tests, and good correlation between them over time was obtained. A predictive model of the maximum lateral Pressure (Pmax) and its evolution over time (PL) was proposed, related to SCC paste thixotropy (Athix,p), casting height (H) and SCC pressure decay coefficient (Cd)., Ministerio de Economía y Competitividad, Ministerio de Ciencia e Innovación, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Rheology and early age evaluation of 3D printable cement-limestone filler pastes with nanoclays and methylcellulose

  • Márquez Martín, Álvaro|||0000-0001-8554-9614
  • Varela Recio, Hugo|||0000-0001-8094-6071
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
Nanoclays (NC) are known to increase the structural build-up of cement-based materials (CBM) while methylcellulose (MC) is used to increase open time and workability, helping to prevent cold joints in 3D Printing applications. The combination and compatibility of both NC and MC could lead to the design of new 3D printable CBM able to tackle all the manufacturing process requirements. The aim of the study is to evaluate the effect of sepiolite nanoclay and MC on rheology and early age (EA) parameters of cement-limestone filler pastes for 3D printing applications, identifying fresh structural build up and setting mechanisms. The effect of two cement types with coarser and finer particle size distribution (CEM I 42.5-R and CEM I 52.5-R, respectively) was considered. Pastes rheology was characterized by Cone Penetration Test (CPT) and Dynamic Shear Rheometer (DSR). EA was monitored by P- and S-waves Ultrasonic Pulse Velocity (UPV), internal temperature, capillary pressure and drying shrinkage. Fresh Shear Yield Stress (?0) and shear elastic modulus (G), effective thixotropy (Athix), critical strain (?crit) and their evolution over time were calculated form CPT and DSR experimental results. A limit of usability was defined for ?0 up to 20 kPa for CPT with a 30º tip cone. Although pastes with both NC and MC showed thixotropy, NC reduced ?crit while MC strongly increased it. NC significantly increased Athix and ?G with coarser particle size cement when compared to the finer cement. MC delayed hydration reaction and setting, while NC did not affect early age stages. On the other hand, combining NC and MC increased superplasticiser demand and reduced effective thixotropy (Athix). Finally, an integrated overview of the physical and chemical mechanisms involved in rheology and early age properties of cement-based systems and the key experimental parameters for their identification was proposed., Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Rheology characterization of 3D printing mortars with nanoclays and basalt fibers

  • Varela Recio, Hugo|||0000-0001-8094-6071
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
  • Sonebi, Mohammed
3D printing has become one of the most innovative technologies for cement-based systems (CBS). However, recent studies have shown some issues related to printability and buildability (water drainage, plugs on extruder die, spreading of first layer, etc). To achieve a proper rheology control of CBS, it is essential to adapt the material fresh state properties (initial shear yield stress and structural build-up). In this study, a reference cement-based mortar with fly ash (25%), a 1:1.5 binder to sand ratio and a 0.38 water to binder ratio was used. A polycarboxilate ether-based superplasticizer was added until a consistency of around 1 kPa, measured with the cone-penetration test, was reached. Then, small amounts of several types of nanoclays (NC) in powder and slurry form (sepiolite, attapulgite and bentonite) and natural fibers were added to modify mortar rheological properties. The aim of the study was to characterize the rheological properties of 3D printing mortar samples with NC and basalt fibers (BF) to understand printability and buildability of this material. Cone-penetration test, flow table test and slump test were used to characterize 3D printing capacities. The cone-penetration test was performed in stirred and left at rest samples to assess shear yield stress before and after material deposition. Nanoclays showed a remarkable capacity to retain water and avoid drainage during extrusion but also to increase fresh state strength of material over time. Besides, they increased shear yield stress over time when left at rest. On the contrary, samples stirred over time did not show any increase of shear yield stress, especially samples with slurry nanoclays. Natural fibers also reduced drainage and enhance printability control regarding to reference mortar. BF also enhanced a performance on stirred sample but showed slightly changes on structural build-up at rest, mainly governed by NC effect., Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación, Comisión Europea, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Extrusion and structural build-up of 3D printing cement pastes with fly ash, nanoclays and VMAs

  • Varela Recio, Hugo|||0000-0001-8094-6071
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
  • Perrot, Arnaud
3D printing technology (3DP) has provided new design and structural opportunities for cement-based systems (CBS) in architectural construction. However, there are still some issues related to extrudability and buildability of CBS, which can be overcome by using components for CBS rheology control. In this study, three types of nanoclays, a bentonite (BEN), a sepiolite (SEP) and an attapulgite (ATT), and two viscosity modifying admixtures (VMAs), a poly-acrylamide (VMA1) and a methylcellulose ether (VMA2), were added to a reference cement-fly ash 3D printing paste to evaluate their impact on CBS rheological properties and their implications in extrusion and buildability for 3DP. A polycarboxylate-ether based high range water-reducing admixture (HRWRA) was used to reach a target stiff consistency. Four laboratory tests were used to assess paste rheology, extrusion and structural build-up. Proper and deficient material extrusion limits were defined considering cohesion and initial yield stress. It was found that the combination of VMA2 and SEP increased cohesion, enhancing extrusion and avoiding water drainage and frictional behavior of pastes, producing properly extrudable paste. SEP by itself also improved structural build-up. Besides, samples with NC and VMAs required larger amounts of HRWRA, delaying cement setting and compressive strength gain., Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación, Comisión Europea, Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Synergies on rheology and structural build-up of fresh cement pastes with nanoclays, nanosilica and viscosity modifying admixtures

  • Varela Recio, Hugo|||0000-0001-8094-6071
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
  • Palomar Herrero, Irene|||0000-0003-2743-3618
  • Sepulcre Aguilar, Alberto
Nanoclays, nanosilica and viscosity modifying admixtures can be used to tune rheological properties of cement pastes, in order to fulfill the requirements for non-conventional cast-in-place techniques. An experimental study on cement paste rheology was carried out to evaluate their combined effects on fluid cement pastes" properties. A reference paste with cement blended with limestone filler and a low water to binder ratio was designed. A high range water reducing admixture (HRWRA), three types of viscosity modifying admixtures (VMA), and five nanocomponents (nanosilica and four different nanoclays) were added. Flowability, initial rheological properties and structural build-up of cement pastes were assessed with mini-cone slump test and dynamic shear rheometer test (DSR). The synergies between nanoclays, nanosilica and VMAs were evaluated. It was observed that an adequate combination of admixtures and nanoclays reduced the amount of HRWRA required to achieve target flowability, regarding the same components uncombined. The type and amount of VMAs and nanocomponents also produced changes on yield stress, viscosity and structural build-up. Their effect on structural build-up of fresh paste was related to reversible and non-reversible mechanisms, comparing the reduction of spread diameter of fresh samples stirred and left at rest over time measured with the mini-cone., Ministerio de Economía y Competitividad, Ministerio de Ciencia e Innovación
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Evaluation of basalt fibers and nanoclays to enhance extrudability and buildability of 3D-printing mortars

  • Varela Recio, Hugo|||0000-0001-8094-6071
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
  • Sonebi, Mohammed
A study of the rheological and fresh mechanical properties of fly ash-cement 3D printing (3DP) mortars with six types of nanoclays (NC) as rheology modifiers, two sepiolites, three attapulgites and one bentonite, and reinforced with short basalt fibers (BF) was carried out. Fresh mortar properties were evaluated with a flow table test (FTT), cylindrical slump test (CST) and conepenetration test (CPT) on samples left at rest and stirred before testing. Squeeze test (SQT) was carried out on samples cast-in-the-mold and 3D printed to compare the effects of 3DP on the fresh mechanical behavior. Extrudability was assessed with an electrical barrel extrusion device. NC and BF enhanced mortar cohesion by preventing water drainage and improving material extrudability. NC increased shear yield stress (tau₀) over time on samples left at rest, enhancing reversible thixotropy. Besides, NC required larger amounts of superplasticizer, increasing open time windows. Among NC, Sepiolite in powder form showed the best fresh mechanical perfor- mance on 3DP samples. BF enhanced extrudability due to the bridging effect but also shows mechanical synergies with some NC. 3DP samples showed lower compressive yield stress and Young modulus evolution over time (sigma˙ and E˙ ) than cast-in-the-mold samples, due to their layered structure., Universidad de Alcalá, Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación, Comisión Europea (Fondos Next Generation)