Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 10
Encontrada(s) 1 página(s)

e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

New low carbon footprint cement-lime mortar with phase change materials (PCM) and biomass ash for thermal enhancement of buildings

  • Guardia Martín, Cynthia|||0000-0003-4442-8933
  • Guerrero Gil, Ana
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
  • Ramallo Aznar, Laura|||0000-0003-3822-6868
  • Palomar Herrero, Irene|||0000-0003-2743-3618
Many studies focus on new advanced materials, such as Phase Change Materials (PCMs), to fulfill the increasing requirements for energy efficiency set by the European Commission. PCM have demonstrated thermal properties enhancement as thermal accumulators regarding to other traditional building materials, due to their heating storage capacity. Besides, it is necessary to reduce carbon footprint of plasters and renderings and replacing cement by lime and biomass ashes emerges as a potential solution. This work presents an experimental study on the physical, mechanical and thermal properties of low carbon footprint cement-lime mortars with the addition of PCM (10% and 20%) and the replacement of cement by biomass ashes (10% and 20%). Thermal performance was assessed on mortar pastes, using Differential Scanning Calorimetry, and on mortar samples under different environmental conditions in a climate chamber. The results showed the influence of the addition of PCM on physical and mechanical mortars’ properties, as well as their thermal performance, increasing mortar energy storage capacity. Partial replacement of cement by biomass ash slightly reduced thermal enhancement. It was observed that paste results could be related to mortars properties, which pointed out that paste phase design can be used to obtain target mortar properties., Comisión Europea (Fondos Next Generation), Universidad de Alcalá, Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Early age and hardened properties of 3D printable cement-lime mortars with microencapsulated PCM and cellulose microfibers

  • Ramallo Aznar, Laura|||0000-0003-3822-6868
  • Márquez Martín, Álvaro|||0000-0001-8554-9614
  • Palomar Herrero, Irene|||0000-0003-2743-3618
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
The design of sustainable functionalized materials suitable for new building technologies has become a challenge for the construction sector. In this study, 3D printable cement-lime mortars incorporating microencapsulated phase change material (PCM) and cellulose microfibers (CMF) were designed and experimentally characterized considering the requirements for architectural applications. The use of lime aims to reduce environmental impact, PCM intends to enhance thermal performance and CMF to provide early age integrity. Two reference mortars were designed, with and without CMF, and PCM was incorporated at 10, 20 and 30% into both reference mixtures. An experimental program was carried out evaluating mortars’ fresh state rheological properties, early age performance and short- and long-term hardened-state physical, thermal and mechanical properties. Long- term carbonation was also assessed. The experimental approach provided a comprehensive understanding of how these components interact across all relevant stages of material development, from fresh state to long-term performance. Lime densified mortar matrix, due to carbonation, contributing to strength gain and reducing water absorption. PCM improved thermal behavior by enhancing their energy storage capacity up to a 35 – 40%, while CMF mitigated early age setting delays in mixtures containing PCM but reduced the thermal storage enhancement at PCM contents above 20%., European Commission, Junta de Castilla-La Mancha
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Fresh and hardened properties of cellulose fiber-reinforced mortars for 3D printing in construction

  • Pimentel Tinoco, Matheus
  • Márquez Martín, Álvaro|||0000-0001-8554-9614
  • Ramallo Aznar, Laura|||0000-0003-3822-6868
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
  • Mendoza Reales, Óscar Aurelio
  • Dias Toledo Filho, Romildo
With the ongoing advancement of 3D printing technology in the construction sector, the requirement for materials with optimized fresh and mechanical properties is becoming more critical. Natural fiber-reinforced mortars can be an effective solution by enhancing material?s printability. This work evalu-ates the effect of cellulose microfibers (CF) on fresh and hardened proper-ties of 3D printable mortars. A reference mortar was prepared with 0-1 mm sand and 0.4 water-to-cement ratio, and three volumetric fractions of fibers were used: 2.5, 7.5, and 12.5 % by mortar volume. Fresh-state properties were studied using flow table and fresh compression tests. Physical and me-chanical tests were also conducted to assess the effect of fibers on the hard-ened state properties. A robotic 3D printer was used to assess mortar printa-bility. Fresh state results demonstrated that CF significantly increased rheo-logical properties over time, enhancing thixotropic behavior. 3D printing tests showed that CF improved buildability, although limited extrudability and shortened the printing open time. Additionally, CF increased 28-days me-chanical strength of mortars; however, they also enlarged capillary water ab-sorption, which could impact durability. The results underscore the potential of CF to modulate fresh and hardened mechanical properties of 3D printable mortars for construction applications., Comisión Europea (Fondos Next Generation)
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

3D Printing Architectural Applications of cement-lime mortars with microencapsulated Phase Change Materials (PCM)

  • Márquez Martín, Álvaro|||0000-0001-8554-9614
  • Ramallo Aznar, Laura|||0000-0003-3822-6868
  • Varela Recio, Hugo|||0000-0001-8094-6071
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
  • Puentes Mojica, Javier|||0000-0001-8748-7664
3D printing technology arouses great interest for its application in architecture on facades and building enclosures that still need to be explored. An experimental study of 3D printing laboratory prototypes using low-carbon ce- ment-lime mortars with microencapsulated Phase Change Material (PCM) was carried out to evaluate its application for adaptative building enclosures. Rheology, extrudability and buildability of PCM cement-lime mortars were assessed. Cellulose fibers and rheology modifiers, as sepiolite nano-clay, were used to enhance mortar properties. Rheological parameters were measured using a Dynam- ic Shear Rheometer (DSR) and Cone Penetration Test (CPT) in fresh state. Fresh compressive strength evolution was assessed by fresh compressive strength test (Squeeze Test) and Early Age monitoring was carried out to keep track of cement hydration and structural build up progress. Extrudability and buildability of mixtures were evaluated by means of RAM Extrusion Test and laboratory 3D printing prototype. This approach provided new knowledge on the design of high thermal performance mortars using digital fabrication in architectural ap- plications, contributing to the digitalization and sustainability of construction and building practice., Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación, Comisión Europea (Fondos Next Generation), Universidad de Alcalá
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Bio-based self-modulating thermal and moisture buffer mortars for architectural applications

  • Palomar Herrero, Irene|||0000-0003-2743-3618
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
  • Puentes Mojica, Javier|||0000-0001-8748-7664
  • Varela Recio, Hugo|||0000-0001-8094-6071
New construction materials for architectural applications need to face environmental impact and energy efficiency issues. Self-modulating materials are promising solutions to optimize the energy performance of buildings, by compensating climatic hygro-thermal changes. Phase-change materials (PCM) and Superabsorbent polymers (SAP) highlight among bio-based components that can be used to design self-modulating mortars. On one hand, PCM can storage and release thermal energy, modulating heat flow and reducing heating and cooling energy demand. On the other, SAP can help to achieve suitable indoor conditions as they level air humidity and contribute to an evaporative cooling effect. In addition, these polymeric materials can be made from renewable bio-resources, becoming bio-based materials. This paper presents a study reporting materials selection, mortar composition design and experimental tests and procedures used to assess thermal and moisture self-modulating properties of PCM and SAP modified mortars for architectural applications as buffer layers. A pervious cement-lime mixture was designed and different amounts and combinations of two types of SAP (spherical and irregular particle shape) and a microencapsulated PCM were evaluated. Mortars? fresh workability and setting and hardened physical and mechanical properties, microstructure, thermal (heat conductivity and storage properties) and hygric parameters (water and vapor transport and storage) and long term carbonation were studied. The preliminary results of self-modulating mortars showed that SAP and PCM can increase moisture and thermal properties, enhancing buffer capacities of architectural mortar renderings., Comunidad de Madrid, Universidad de Alcalá, Comisión Europea (Fondos Next Generation)
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Experimental thermal evaluation of multilayer 3D printed architectural enclosures made of lime-cement mortars with PCM and Cellulose Fibers

  • Ramallo Aznar, Laura|||0000-0003-3822-6868
  • Márquez Martín, Álvaro|||0000-0001-8554-9614
  • Palomar Herrero, Irene|||0000-0003-2743-3618
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
The reduction of carbon footprint towards sustainability in the con-struction sector demands innovative construction techniques and novel and bio-based building materials to optimize the building process and make it more sus-tainable. This study evaluates experimentally the dynamic thermal performance on hardened lime-cement mortars with Phase Change Materials (PCM) and Cel-lulose Fibers (CF) for 3D printing applications. Four material?s design strategies were followed to reduce carbon footprint: partial substitution of cement by air-lime, addition of a Phase Change Material (PCM) to increase thermal energy ef-ficiency, nanoclays to improve material printability and Cellulose Fibers (CF) to enhance extrudability and enlarge durability. A mortar mixture with 20% of PCM was selected to produce three types of specimens: cast in the mold plate, 3D-printed plate and 3D-printed truss. A multilayer enclosure system with a thermal insulation layer plus a mortar specimen was tested using a climate chamber to simulate dynamic cooling and heating cycles, ranging 15 - 30ºC. The experi-mental results showed that the manufacturing procedure did not modify the high thermal efficiency of the material, while a truss cross-section element largely in-creased energy efficiency of the enclosure system., Universidad de Alcalá, Comisión Europea (Fondos Next Generation), Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Piezoresistive self-compacting concretes (PSSC) with carbon fibers (CF) and nano-fibers (CNF) for structural health monitoring

  • Puentes Mojica, Javier|||0000-0001-8748-7664
  • Palomar Herrero, Irene|||0000-0003-2743-3618
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
Real-time monitoring of structural health is a key issue for structural safety. Monitoring systems have evolved from external devices into intrinsic selfdetection systems (SDS) becoming diagnostic and monitoring tools useful to maintain and increase structural durability. Furthermore, SDS are an economical and efficient solution for using human and technical resources towards sustainability. Self-sensing materials are considered a promising SDS technology to replace integrated connected or embedded systems, which have many limitations. Self-compacting concrete (SCC) is an advanced material that can become a self-sensing concrete by the incorporation of carbon-based materials, which provide the concrete matrix with piezoresistivity properties, transforming the material into a sensor by itself. The advantage of using SCC lies in its larger paste content which allows the use of hybrid systems of carbon-based additions, such as carbon nanofibres (CNF) and carbon fibres (CF). This combination can produce a synergistic response, improving the properties that can be achieved by incorporating each of them separately. Through the integration of electrical and piezoresistive properties, Piezoresistivity-SSC (PSCC) can collect real-time state variation information relating mechanical responses to piezoresistivity. The aim of this study was to identify the threshold of the effective admixtures content maintaining acceptable workability and achieving PSSC self-sensitivity., Comisión Europea (Fondos Next Generation)
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Use of Bio-Carbon Fibers for self-sensing cement-based composites for Structural Health Monitoring

  • Puentes Mojica, Javier|||0000-0001-8748-7664
  • Palomar Herrero, Irene|||0000-0003-2743-3618
  • Lopesino Cerqueira, Yaiza
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
The use of functionalized components in cement-based composites (CBC) is an innovative way to provide novel material?s capabilities. Carbon-based ad-ditions and fibers can modify electrical properties of CBC, such as piezore-sistivity (PZR). PZR enables a new intrinsic capacity of CBC, relating the variation of material?s electrical resistance to material?s stress when subjected to external loads, successfully transforming CBC into a self-sensing material that can be used for Structural Health Monitoring (SHM). This study aims to evaluate the use of carbon fibers of biological sources (CF-BIO), obtained from lignin as raw material, which is a sustainable alter-native to petroleum carbon fibers (CF-PAN), due to its natural origin and lower environmental impact. Fiber content required for achieving PZR ca-pacity of CBC has been already defined for CF-PAN. The variation of elec-trical and piezoresistive properties as an effect of self-sensitive capacity were tested. These measurements were be used to calculate the fractional change resistivity (FCR) and the sensitivity rate of the material (Csens)., Agencia Estatal de Investigación, Ministerio de Ciencia, Innovación y Universidades, Comisión Europea (Fondos Next Generation)
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Printability assessment of 3D printing cement-lime mortars with microencapsulated PCM

  • Márquez Martín, Álvaro|||0000-0001-8554-9614
  • Ramallo Aznar, Laura|||0000-0003-3822-6868
  • Palomar Herrero, Irene|||0000-0003-2743-3618
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
An experimental study was conducted to evaluate the printability of cement–lime mortars designed for 3D printing applications, incorporating a microencapsulated phase-change material (PCM) and cellulose microfibers (CMFs). The influence of both PCM and CMFs on mortars’ rheology was measured by rheometer tests (DSR) and cone penetration tests (CPT). A ram extrusion test was used to evaluate the extrudability, and an unconfined uniaxial compression test (UUCT) allowed the assessment of buildability. Finally, several lab-scale prototypes were 3D-printed. The results showed that the incorporation of PCM affected mortar’s rheology and workability due to the reduction in paste volume and the increase in superplasticizer (SP) demand. However, the spherical particle shape of microencapsulated PCM was found to ease the extrusion process. After being extruded, mortars with lower volumetric fractions of PCM exhibited increased fresh strength and stiffness, whereas larger amounts reduced both parameters. The use of CMFs considerably reduced the extrusion force and improved the extrusion quality. Lab-scale 3D-printed prototypes were successfully manufactured using mortars with a 20% volumetric fraction of PCM., European Commission, Junta de Comunidades de Castilla-La Mancha
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Libro o Monografía (Book)

Thermal evaluation of low-carbon lime cement mortars with PCM for 3D printing architectural applications

  • Ramallo Aznar, Laura|||0000-0003-3822-6868
  • Barluenga Badiola, Gonzalo|||0000-0002-2996-3412
  • Palomar Herrero, Irene|||0000-0003-2743-3618
The design of innovative low-carbon and energy efficient building materials and technologies are on the basis to construction and architecture sustainability. New lime-cement mortars with microencapsulated Phase Change Material (PCM) for 3D printing architectural applications were designed and experimentally evaluated to collaborate into achieving this goal. The innovation comes through integrating three strategies: reducing carbon footprint and embodied energy by partially replacing ordinary Portland Cement (OPC) by lime; enhancing energy efficiency and storage capacity by incorporating microencapsulated PCM; improving printability and buildability for 3D printing architectural enclosures by using rheology modifiers. Eight lime-cement mortars with PCM, Cellulose Fibers (CF) and rheology modifiers, nanoclays and organic VMAs, were designed and characterized in fresh and hardened state to led to an innovative building technology regarding conventional architectural facades. Hardened thermal properties were evaluated by Differential Scanning Calorimetry (DSC) and on reduced scale experimental simulations applying cooling and heating cycles on mortar plate samples using a climate chamber. Hardened mechanical properties were also tested to evaluate compressive and flexural strength. PCM boosted mortars’ thermal performance, improving mass enthalpy up to 60%, while CF slightly attenuated this reduction. Accordingly, PCM lime-cement mortars showed excellent fresh properties to be used for 3D printing digital fabrication in architectural applications, and CF along with rheology modifiers enhanced buildability and thixotropy both in initial and set up times. This study’s main focus is on the mortars’ physical, mechanical and thermal properties., Universidad de Alcalá, Comisión Europea (Fondos Next Generation), Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación