Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 10
Encontrada(s) 1 página(s)

RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Co-complexes on modified graphite surface for steady green hydrogen production from water at neutral pH

  • Toledo-Carrillo, Esteban A.
  • García-Rodríguez, Mario
  • Morallon, Emilia
  • Cazorla-Amorós, Diego
  • Ye, Fei
  • Kundi, Varun
  • Kumar, Priyank V.
  • Verho, Oscar
  • Dutta, Joydeep
  • Åkermark, Bjorn
  • Das, Biswanath
  • Cazorla-Amorós, Diego|||/items/bab354fe-ec79-49e0-a4f3-5288ee396750
  • García-Rodríguez, Mario|||/items/4e75ee7c-2337-493c-b5d4-048aa25f8fef
  • Morallon, Emilia|||/items/a15cf511-9365-4c40-afcb-ea29d4418244
Green hydrogen production from water is one attractive route to non-fossil fuel and a potential source of clean energy. Hydrogen is not only a zero-carbon energy source but can also be utilized as an efficient storage of electrical energy generated through various other sources, such as wind and solar. Cost-effective and environmentally benign direct hydrogen production through neutral water (∼pH 7) reduction is particularly challenging due to the low concentration of protons. There is currently a major need for easy-to-prepare, robust, as well as active electrode materials. Herein we report three new molecular electrodes that were prepared by anchoring commercially available, and environmentally benign cobalt-containing electrocatalysts with three different ligand frameworks (porphyrin, phthalocyanine, and corrin) on a structurally modified graphite foil surface. Under the studied reaction conditions (over 7 h at 22°C), the electrode with Co-porphyrin is the most efficient for the water reduction with starting ∼740 mV onset potential (OP) (vs. RHE, current density 2.5 mA/cm2) and a Tafel slope (TS) of 103 mV/dec. It is followed by the molecular electrodes having Co-phthalocyanine [825 mV (OP), 138 mV/dec (TS)] and Vitamin-B12 (Co-corrin moiety) [830 mV (OP), 194 mv/dec (TS)]. A clear time-dependent improvement (>200 mV over 3 h) in the H2 production overpotential with the Co-porphyrin-containing cathode was observed. This is attributed to the activation due to water coordination to the Co-center. A long-term chronopotentiometric stability test shows a steady production of hydrogen from all three cathode surfaces throughout seven hours, confirmed using an H2 needle sensor. At a current density of 10 mA/cm2, the Co-porphyrin-containing electrode showed a TOF value of 0.45 s−1 at 870 mV vs. RHE, whereas the Co-phthalocyanine and Vitamin-B12-containing electrodes showed 0.37 and 0.4 s−1 at 1.22 V and 1.15 V (vs. RHE), respectively.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Metal oxide Perovskite-Carbon composites as electrocatalysts for Zinc-air batteries. Optimization of ball-milling mixing parameters

  • García-Rodríguez, Mario
  • Flores-Lasluisa, Jhony Xavier
  • Cazorla-Amorós, Diego
  • Morallon, Emilia
  • Cazorla-Amorós, Diego|||/items/bab354fe-ec79-49e0-a4f3-5288ee396750
  • García-Rodríguez, Mario|||/items/4e75ee7c-2337-493c-b5d4-048aa25f8fef
  • Morallon, Emilia|||/items/a15cf511-9365-4c40-afcb-ea29d4418244
  • Flores-Lasluisa, Jhony Xavier|||/items/6f146453-a961-4a3a-b897-ea7721edb6db
Zn-air batteries (ZABs) are promising electrochemical devices to store energy. Metal oxide perovskites mixed with carbon materials are highlighted as interesting materials for this application because of their appropriate bifunctional performance in oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). The interaction between both components of the electrocatalyst is important in the bifunctional electrocatalytic activity, and the mixing method plays an important role in this interaction. Then, different mixing methods have been studied in this work (ball-milling, mortar and manual shaking). The use of different physicochemical techniques such as temperature programmed desorption (TPD), temperature programmed reduction (TPR) and X-ray photoelectron spectroscopy (XPS) in the materials characterization, allows us to conclude that the mixing method strongly influences the particle size and the interaction between both components, which determine the final electrocatalytic activity. The materials prepared by ball-milling displayed the best performance. Herein, the experimental conditions were optimized to obtain electrocatalysts with enhanced electrocatalytic activity for ORR and OER. Low rotating speed, air atmosphere and low ball-milling time generate electrocatalysts with a small nanoparticle size, more homogeneous and with a higher interaction between both components, which enhances electron transfer, and consequently, the overall oxygen-involved reactions. The best electrocatalyst obtained was studied as air-electrode in a Zn-air battery and it was compared to a commercial Pt/C electrocatalyst, obtaining higher cyclability (55.2 vs. 51.7%) for 30 h, and higher energy density at 5 mA/cm2 (764 mAh/g vs. 741 mAh/g).
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Eco-Friendly Mechanochemical Synthesis of Bifunctional Metal Oxide Electrocatalysts for Zn-Air Batteries

  • García-Rodríguez, Mario
  • Cazorla-Amorós, Diego
  • Morallon, Emilia
  • Cazorla-Amorós, Diego|||/items/bab354fe-ec79-49e0-a4f3-5288ee396750
  • García-Rodríguez, Mario|||/items/4e75ee7c-2337-493c-b5d4-048aa25f8fef
  • Morallon, Emilia|||/items/a15cf511-9365-4c40-afcb-ea29d4418244
The development of green and environmentally friendly synthesis methods of electrocatalysts is a crucial aspect in decarbonizing energy generation. In this study, eco-friendly mechanochemical synthesis of perovskite metal oxide-carbon black composites is proposed using different conditions and additives such as KOH. Furthermore, the optimization of ball milling conditions, including time and rotational speed, is studied. The mechanochemical synthesis in solid-state conditions without additives produces electrocatalysts that exhibit the highest bifunctional electrochemical activity towards both oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). Moreover, this synthesis demonstrates a lower Environmental Impact Factor (E-factor), indicating its greener nature, and due to its simplicity, it has a great potential for scalability. The obtained bifunctional electrocatalysts have been tested in a rechargeable zinc-air battery (ZAB) for 22 h with similar performance compared to the commercial catalyst (Pt/C) at significantly lower cost. These promising findings are attributed to the enhanced interaction between the perovskite metal oxide and carbon material and the improved dispersion of the perovskite metal oxide on the carbon materials.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Unraveling the interfacial degradation mechanism of a metal oxide electrocatalyst/gas diffusion layer in Zn–air batteries through FIB-SEM analysis

  • García-Rodríguez, Mario
  • González-Souto, Lorena
  • Hernández-Saz, Jesús
  • Juan Juan, Jerónimo
  • Calvino, Jose J.
  • Cazorla-Amorós, Diego
  • Morallon, Emilia
  • García-Rodríguez, Mario|||/items/4e75ee7c-2337-493c-b5d4-048aa25f8fef
  • Cazorla-Amorós, Diego|||/items/bab354fe-ec79-49e0-a4f3-5288ee396750
  • Morallon, Emilia|||/items/a15cf511-9365-4c40-afcb-ea29d4418244
Focused Ion Beam -Scanning Electron Microscopy (FIB-SEM) was employed to investigate the Gas Diffusion Layer (GDL), electrocatalyst, and electrolyte interface in rechargeable Zn-Air Batteries (ZABs) using Fresh and Used samples (before and after long-term electrocatalytic activity, respectively). The electrocatalyst was based on (hydro-)oxides of manganese, cobalt and lanthanum and carbon material. The results reveal a loss of material compaction in the Used sample, accompanied by the formation of pores and irregular gaps, as well as enhanced permeation of the electrocatalyst through the GDL, as evidenced in the tomogram. Interestingly, the analysis of the distribution of elements in the Used sample shows important differences, strongly dependent on their chemical properties in the electrolyte used. Mn and Co, the more electroactive elements for the oxygen-involved reactions, remain in proximity to the electrolyte interface, while La forms a preferential region more distant and parallel to the electrolyte. XPS results indicate that the formation of this region is associated with the generation of lanthanum acetate species, which are responsible for the decrease in conductivity of the Used sample, as demonstrated by electrochemical impedance spectroscopy (EIS) experiments, in addition to impairing O 2 diffusion along the GDL. Furthermore, DFT calculations support that the formation of lanthanum acetate species from the metal (hydro)oxides is energetically favorable in presence of zinc acetate electrolyte in ZABs.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Enhanced lanthanum-stabilized low crystallinity metal oxide electrocatalysts with superior activity for oxygen reactions

  • García-Rodríguez, Mario
  • Cazorla-Amorós, Diego
  • Morallon, Emilia
  • Cazorla-Amorós, Diego|||/items/bab354fe-ec79-49e0-a4f3-5288ee396750
  • García-Rodríguez, Mario|||/items/4e75ee7c-2337-493c-b5d4-048aa25f8fef
  • Morallon, Emilia|||/items/a15cf511-9365-4c40-afcb-ea29d4418244
Oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) are key electrochemical reactions for the development of rechargeable Zn-air batteries. However, due to the high cost of commercial noble metal-based catalysts and their limited bifunctionality, it is necessary the design of new electrocatalysts. In this study, stable electrocatalysts have been synthesized through a hydrothermal method and further low-temperature thermal treatment. The materials consist of La stabilized low crystallinity Mn and Co metal (hydro-)oxides. The electrocatalytic performance of these materials has been compared with counterparts calcined at higher temperatures. The findings demonstrate that materials synthesized at lower temperatures and with low crystallinity exhibit superior electrocatalytic activity for both ORR and OER. Moreover, the research highlights the favorable influence of the lanthanum cation, which enhances changes of surface morphology and oxidation states of other cations (Mn and Co). Additionally, the positive contribution of the carbon component to electrochemical activity and electrical conductivity has been elucidated. The best electrocatalyst was studied in a rechargeable Zn-air battery with a durability of up to 120 hours. They exhibited better stability and performance than the commercial Pt/C + RuO2 catalyst currently used.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

High-performance transition metal nitride/carbon nanofiber composites as positive electrode in rechargeable Zn-air batteries

  • Posadzy, Marta
  • García-Rodríguez, Mario
  • Flores-Lasluisa, Jhony Xavier
  • Moyseowicz, Agata
  • Kordek-Khalil, Karolina
  • Cazorla-Amorós, Diego
  • Morallon, Emilia
  • Cazorla-Amorós, Diego|||/items/bab354fe-ec79-49e0-a4f3-5288ee396750
  • García-Rodríguez, Mario|||/items/4e75ee7c-2337-493c-b5d4-048aa25f8fef
  • Morallon, Emilia|||/items/a15cf511-9365-4c40-afcb-ea29d4418244
  • Flores-Lasluisa, Jhony Xavier|||/items/6f146453-a961-4a3a-b897-ea7721edb6db
Rechargeable zinc-air batteries (ZABs) represent one of the most promising devices for future portable energy storage. However, bifunctional and cost-effective electrocatalysts for oxygen evolution reaction (OER) and oxygen reduction reaction (ORR) need to be developed for practical real-world scenarios. This work presents a comprehensive optimization of the simple and green hydrothermal method to synthesise metal (Co/Fe) nitrides integrated with carbon nanofibers (CNF). The prepared nanocomposites exhibit remarkable electrocatalytic performance in OER and ORR. The combination of both metals in the CoFe-Fe3N/CNF material induces the highest bifunctional activity, attributed to a synergistic effect between the metals, and presence of a thin layer of cobalt oxide at the surface. The CNF content in the composite material is optimised, revealing the favourable CNF concentration of 60 wt.%. The electrocatalysts with the highest bifunctional activity were evaluated as positive electrodes in ZABs, achieving superior cycling stability compared to a commercial Pt/C-RuO2 electrocatalyst, and sustaining stability up to 60 hours at a current density of 5 mA/cm2. These results underline the significant potential of cobalt-iron nitride/carbon nanofiber composites as highly efficient catalysts for oxygen electrochemical reactions and as promising components for improving the performance of rechargeable Zn-air batteries, thus contributing to the advancement of clean energy technologies.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Effect of Sr substitution in La1-xSrxMn0.7Co0.3O3 perovskites and their application in Zn-air batteries

  • Flores-Lasluisa, Jhony Xavier
  • García-Rodríguez, Mario
  • Cazorla-Amorós, Diego
  • Morallon, Emilia
  • Cazorla-Amorós, Diego|||/items/bab354fe-ec79-49e0-a4f3-5288ee396750
  • García-Rodríguez, Mario|||/items/4e75ee7c-2337-493c-b5d4-048aa25f8fef
  • Morallon, Emilia|||/items/a15cf511-9365-4c40-afcb-ea29d4418244
  • Flores-Lasluisa, Jhony Xavier|||/items/6f146453-a961-4a3a-b897-ea7721edb6db
La1-xSrxMn0.7Co0.3O3 perovskite materials were synthesized by a sol-gel method for their application as an air electrode in Zn-air batteries. Through physicochemical techniques, it was determined that the Sr substitution level influences the crystallite size and purity degree of the perovskite structure. Moreover, the surface chemistry, including oxygen chemisorbed species and different oxidation states of 3d cations, can be tailored through the Sr substitution level. The metal oxides were mixed with carbon black (Vulcan XC-72R) to improve the electrochemical performance. Temperature Programmed Desorption (TPD) and Temperature Programmed Reduction (TPR) studies revealed the strong interaction existing between both components, which tends to increase with the Sr substitution level due to the smaller crystallite size. However, low Sr substitution level results in better electrocatalytic performance because of a moderate concentration increase of Mn4+ and oxygen chemisorbed species. Moreover, it helps to preserve the perovskite structure and increases the concentration of Co3+ species, which are more catalytic towards OER. Thus, the La0.8Sr0.2Mn0.7Co0.3O3/Vulcan material was studied in a Zn-air battery and compared to a commercial Pt/C + RuO2 electrocatalyst. The material shows comparable long-term charge-discharge performance to Pt/C + RuO2 after 20 h of cycling.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

In-situ synthesis of encapsulated N-doped carbon metal oxide nanostructures for Zn-air battery applications

  • Flores-Lasluisa, Jhony Xavier
  • García-Rodríguez, Mario
  • Cazorla-Amorós, Diego
  • Morallon, Emilia
  • Cazorla-Amorós, Diego|||/items/bab354fe-ec79-49e0-a4f3-5288ee396750
  • García-Rodríguez, Mario|||/items/4e75ee7c-2337-493c-b5d4-048aa25f8fef
  • Morallon, Emilia|||/items/a15cf511-9365-4c40-afcb-ea29d4418244
  • Flores-Lasluisa, Jhony Xavier|||/items/6f146453-a961-4a3a-b897-ea7721edb6db
La, Mn and Co-based materials with diverse compositions encapsulated in N-doped carbon materials were synthesized by an in-situ sol-gel method. The as-prepared materials were physically activated with CO2 giving as a result composites with excellent performance for both oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). The composites were characterized by different physicochemical techniques revealing the importance of porosity created by CO2 activation. This crucial step increases the number of accessible active sites such as Co-Nx-C sites, Co/MnO heterointerfaces and graphitic N groups. Moreover, the formation of La2O2CO3 was detected to enhance electrical conductivity and electrochemical performance and it is active for ORR. Although the composite containing La, Mn and Co has less concentration of the highly active sites, its small particle size favour a better distribution of these sites. The Co-containing composites were tested as air-electrodes in a Zn-air battery and compared to commercial electrocatalysts. All composites showed a better operation in terms of higher cyclability and higher energy density which is a consequence of metal nanostructures encapsulation in N-doped porous carbon shells. Interestingly, the pure Co-based composite showed an outstanding performance related to the high concentration of the Co-Nx-C active sites that provide high activity and stability.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Carbon-Driven Enhancement in Zinc Hexacyanoferrate Composites: A Ball-Milling Approach for High-Performance Zn-Ion Batteries

  • García-Rodríguez, Mario
  • García-Rodríguez, Mario|||/items/4e75ee7c-2337-493c-b5d4-048aa25f8fef
  • Toledo-Carrillo, Esteban A.
  • Dutta, Joydeep
  • Cazorla-Amorós, Diego|||/items/bab354fe-ec79-49e0-a4f3-5288ee396750
  • Morallon, Emilia|||/items/a15cf511-9365-4c40-afcb-ea29d4418244
Transition to a sustainable energy future demands the development of alternative battery technologies beyond lithium-ion batteries, which are challenging for large-scale implementation due to inherent safety concerns and resource scarcity. Aqueous zinc-ion batteries (ZIBs) are a promising solution; however, improvement of the cathode is essential for their widespread adoption. This study investigates the structural modification of zinc hexacyanoferrate (ZnHCF) as cathode materials using ball-milling and the addition of carbon black (Vulcan XC-72R). The improved electroactivity is attributed to the phase transition from cubic to rhombohedral, the conversion of Prussian blue analogue to Prussian white analogue phases, and the synergistic effect produced by the presence of carbon material. These changes lead to the formation of [Fe(CN)6] vacancies, which draw water molecules into interstitial sites. Carbon material plays a crucial role in preserving the crystalline structure of ZnHCF and enhancing the electrochemical performance. The sample milled in presence of carbon material (BM-ZnHCF@C sample) demonstrates superior results compared to the samples unmilled and milled samples without carbon material, achieving a capacity close to 100 mAh g−1 at a current density of 0.5 A g−1. However, after 50 cycles, the capacity decreases by 53.3%, but is restored by replacing the Zn anode while retaining the same cathode. The zinc anode is the primary factor hindering the long-term performance of the assembled battery, as demonstrated by the evolution of the electrode potential over time in the ZIB using a T-type electrochemical cell.
RUA. Repositorio Institucional de la Universidad de Alicante
Publicación Otros (Other)

Enhanced electrocatalytic performance of SrMn1-xCoxO3 perovskite metal oxides for oxygen reactions in Zn-air batteries: Influence of Mn/Co ratio

  • Riquelme-García, Paula
  • García-Rodríguez, Mario
  • Flores-Lasluisa, Jhony Xavier
  • Cazorla-Amorós, Diego
  • Morallon, Emilia
  • Cazorla-Amorós, Diego|||/items/bab354fe-ec79-49e0-a4f3-5288ee396750
  • García-Rodríguez, Mario|||/items/4e75ee7c-2337-493c-b5d4-048aa25f8fef
  • Morallon, Emilia|||/items/a15cf511-9365-4c40-afcb-ea29d4418244
  • Riquelme-García, Paula|||/items/eaa40ff9-6931-43ac-9865-2c13ac4a77c9
  • Flores-Lasluisa, Jhony Xavier|||/items/6f146453-a961-4a3a-b897-ea7721edb6db
Metal oxides of perovskite structure and SrMn1-xCoO3 type have been prepared by a sol-gel synthesis method and mixed with carbon black by ball milling for their use as electrocatalysts for oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) in a Zn-air battery. The composites obtained were characterized by different physicochemical and electrochemical techniques. The results of the characterization revealed the existence of two perovskite phases corresponding to Mn and Co as function of the Mn/Co ratio, whose interaction is related to a positive effect for the electrocatalytic activity. The presence of the M-O-C contribution was detected by XPS, which is related to an improvement in the catalytic activity against ORR/OER due to a better interaction and electron transfer between the perovskite and the carbon material. In addition, important differences were observed in the surface chemical species as a function of Mn/Co ratio and the higher the Co content in the composites the higher the amount of oxygen vacancies. The presence of oxygen vacancies is directly related to an improved OER activity; however, the presence of higher Mn content led to better catalytic results for ORR. The best electrocatalyst was studied in a Zn-air battery obtaining an excellent activity with a cyclability higher than 20 h, which is explained by the appropriate amounts of both Mn and Co.