Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación Set de datos (Dataset)

Supplementary materials for Oil-in-water pickering emulsions stabilized with nanostructured biopolymers: a venue for templating bacterial cellulose [Dataset]

  • Calvo Peña, Víctor
  • Fuentes Varela, Laura
  • Berdejo, Daniel
  • González Domínguez, José Miguel
  • Maser, Wolfgang K.
  • Benito, Ana M.
Chemical structure of the nanostructured biopolymers: Figure S1. Chemical structure of cellulose nanocrystals (A) and chitin nanocrystals (B).-- Polydispersity results of nanostructured biopolymers: Figure S2. Polydispersity indexes of the NBs (CNCs I, CNCs II and ChNCs) in water with different NaCl concentrations.-- Evolution of the visual appearance of PEs: Figure S3. Evolution over time of the PEs made with CNCs I. The images were used to determine the creaming index. Figure S4. Evolution over time of the PEs made with CNCs II. The images were used to determine the creaming index. Figure S5. Evolution over time of the PEs made with ChNCs. The images were used to determine the creaming index.-- BNC production with ChNCs without PEs: Figure S6. BNC culture media without ChNCs (left) and two different ChNCs concentrations (center and right) after 14 days since inoculation. It can be observed that ChNCs precipitate, what reduces the ChNCs incorporation in the BNC composites.-- BNC hydrogels prepared with emulsified culture media: Figure S7. BNC hydrogels prepared with emulsified culture media after cleaning.-- Under Creative Commons Attribution (CC BY) license., Chemical structure of the nanostructured biopolymers. Polydispersity results of nanostructured biopolymers. Evolution of the visual appearance of PEs. BNC production with ChNCs without PEs. BNC hydrogels prepared with emulsified culture media., This research was funded by Spanish MICINN/AEI under projects PID2019-104272RB-C51/AEI/10.13039/501100011033 and PID2020-120439RA-I00, from Spanish CSIC (PIE iniciación ref. 202280I007), and support from Gobierno de Aragón (DGA, Grupo Reconocido DGA-T03_23R) is acknowledged. Víctor Calvo thanks the DGA for funding their Ph.D. contracts (Ref. CUS/581/2020)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación Set de datos (Dataset)

Appendix A. Supplementary data for The aqueous processing of carbon nanofibers via cellulose nanocrystals as a green path towards e-textiles with n-type thermoelectric behaviour [Dataset]

  • Calvo Peña, Víctor
  • Paleo, A. J.
  • González Domínguez, José Miguel
  • Muñoz, Edgar
  • Krause, Beate
  • Pötschke, Petra
  • Maser, Wolfgang K.
  • Benito, Ana M.
Under a Creative Commons license BY-NC-ND 4.0 Deed., Synthesis of cellulose nanocrystals: Cellulose nanocrystals (CNCs) were synthesized following the protocol described in two previous publications.[1,2] 10 g of microcrystalline cellulose (MCC) (Sigma-Aldrich, ref 310697) were dispersed in 45 ml of ultrapure water using an ultrasound bath (45 kHz) for 5 min. Then, 45 ml of H2SO4 98 wt% (Labkem, ref SUAC-00A) were added dropwise to the mixture (externally cooled in an ice/water bath at 0 °C) reaching a final H2SO4 concentration of 64 wt%. This addition was performed fast (less than 5 min) and with magnetic stirring to obtain type I CNCs or slow (longer than 100 min) and with high shear mixing to obtain type II CNCs.[1] After that, the mixture was put in a heating plate at 70°C for 10 minutes for type I CNCs or at ambient temperature for 1 hour for type II CNCs. The reaction was stopped by diluting in 1 liter of ultrapure water at 4°C, also to increase the pH, and the mixture was left decanting overnight at 4°C. The bottom sediment was dialyzed against ultrapure water until a neutral pH was achieved, using specific dialysis membranes (Merck, average flat width 33 mm, ref D9652-100FT). The neutralized dispersions were subjected to centrifugation/re-dispersion cycles at 9000 rpm (9327 rcf) for 1 min to keep only the nanocrystals. The average mass yield and the concentration (Table S1) were determined by lyophilization of 3 aliquots of 30 mL of the CNCs dispersions. The hydrodynamic radii, polydispersity, and ζ-potential were measured using a Malvern Nano ZS instrument, and the mean values of these parameters are presented in Table S1. The CNCs in solid were measured by a Bruker D8 Advance X-Ray diffractometer using a Cu tube as the X-ray source (λ Cu Kα = 1.54 Å), a tube voltage of 40 kV, and a current of 40 mA. The X-Ray diffraction patterns of the prepared CNCs (Fig. S1) confirmed the different presence of the characteristic planes of type I or type II cellulose.--, Synthesis of cellulose nanocrystals: Table S1. Mean values of the characterization results of type I and type II CNCs dispersions. Fig. S1. X-ray diffraction profiles of type I (red) and type II (blue) CNCs. Surface resistivity of n-type thermoelectric cotton textiles as a function of the number of dip-coating cycles: Fig. S2. Surface resistivity (Rsh) of nanocomposite textiles from 1 to 10 immersion cycles with equivalent inks, but different immersion methodology: regular (red) and using a complementary ultrasounds bath treatment for 5 min (black). Measured with an in-line 4-point probe configuration. Error bars show standard deviation of at least 3 repetitions. SEM images of the surface of original and washed CWF@CNF textile samples: Fig. S3. SEM images of the surface of original and washed CWF@CNF textile samples at different magnifications (a) CWF@CNF, (b) CWF@CNF W30 and (c) CWF@CNF W45. Model proposed for describing the nonlinear Seebeck of CNFs and CWF@CNF: The model presented in this work represents the combination of two physical mechanisms occurring in parallel: S(T)=S_met (T)+S_imp (T) (1). Power factor and estimative figure of merit of unwashed and washed samples and CNFs: Table S2. Thermoelectrical properties of dip-coated textiles and carbon nanofibers. References., Financial support from Spanish MCIN/AEI under projects PID2019-104272RB-C51/AEI/10.13039/501100011033 and PID2020-120439RA-I00, from Spanish CSIC (PIE iniciación ref. 202280I007), as well as from Gobierno de Aragón (DGA, Grupo Reconocido DGA-T03_23R) is acknowledged. Vícto Calvo thanks the DGA for funding his PhD contract (Ref. CUS/581/2020). Antonio J. Paleo gratefully acknowledges support from FCT-Foundation for Science and Technology by the “plurianual” 2020–2023 Project UIDB/00264/2020, and European COST Action EsSENce CA19118 for its support with the Short Term Scientific Mission (STSM) grant E-COST-GRANT-CA19118-0ed3a197 at IPF (Dresden). E. Muñoz acknowledges funding from ANID ANILLO ACT/192023 and Fondecyt No 1230440., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación Set de datos (Dataset)

Supplementary information for Towards sustainable TiO2 photoelectrodes based on cellulose nanocrystals as a processing adjuvant [Dataset]

  • Martínez-Barón, Carlos
  • Calvo Peña, Víctor
  • Hernández-Ferrer, Javier
  • Villacampa, Belén
  • Ansón-Casaos, Alejandro
  • González Domínguez, José Miguel
  • Maser, Wolfgang K.
  • Benito, Ana M.
20 figures, 2 tables.-- TEM, size distribution and elemental analysis of CNC: TEM images of the type II CNC are presented in Figure S1 and the distribution of diameters and heights of the CNC are in Figure S2. It can be observed the characteristic shape and size of this type of CNC, with a mean diameter 28 ± 13 nm and a length of 58 ± 15 nm. Type II CNCs were analyzed to determine their composition by elemental analysis and the results are presented in Table S1. The most characteristic result is the relative high mass percentage of sulfur of 3.45%, which is clearly higher than the value in type I CNCs prepared by the same approach. The elemental composition (C, H, N and S) of the CNCs was determined using a LECO 628 elemental analyzer (Velp Scientifica). The elemental analysis was performed in triplicate to ensure reproducibility, and the average values were reported. Commercial TiO2 paste (TiO2-P): Film fabrication: The commercial paste (TiO2-P) was dried in an oven at 120 ºC overnight to remove organic solvents and get a material ready for subsequent solid stated characterization such as XRD and TGA measurements. For the preparation of the photoelectrodes using the commercial paste, an optimized screen-printing procedure was employed following the instructions provided by the supplier. The paste was applied to cover a 1 cm2 surface area of the FTO substrates. Subsequently, the electrode was thermally sintered in an oven with the following temperature profile: 5 minutes at 325 ºC, 5 minutes at 375 ºC, 5 minutes at 450 ºC, and 15 minutes at 500 ºC, under an air atmosphere, according to the instructions from the provider. Prior to the photoelectrochemical (PEC) evaluation, the TiO2 film was activated by treating it at 500 ºC in air for 30 minutes. Preparation of TiO2(NH4OH) and solid material: TiO2(NH4OH) dispersions were prepared by mixing 50 mg of anatase powder, 300 µL of commercial aqueous ammonia (30%) and 19.7 mL of ultrapure water. Then, the resulting mixture was homogenized in an ultrasonic bath for 1 h. Dispersions were freeze-dried to obtain powder materials for further characterization. UV-Vis of the employed materials: Figure S5a shows the transmittance curves of various aqueous dispersions, including freshly prepared TiO2-NPs, TiO2(NH4OH), CNC materials, and the TiO2(NH4OH) material after 24 hours of dispersion preparation. At the selected wavelength of 360 nm, the TiO2- NPs dispersion exhibits the highest transmittance, indicating an unstable system with most of the material settling down. Conversely, the TiO2(NH4OH) material shows lower transmittance values, which moderately increases after 24 hours, evidencing successful dispersion of the TiO2-NPs when ammonia was used. Figure S5b shows the variation of the transmittance for the TiO2(NH4OH), TiO2-CNC and TiO2-CNC(NH4OH) materials with time. The results demonstrate the effective role of ammonia in facilitating the dispersion of TiO2-NPs, although CNC exhibited superior stabilization efficiency. Notably, the combination of ammonia and CNC yields the most stable aqueous dispersions, as evidenced by consistent transmittance values even after 24 hours. TEM of the TiO2(NH4OH) material: TEM images in Figure S6 reveal the presence of TiO2 aggregates, typically smaller than 100 nm. It seems that the addition of NH4OH during the preparation of the TiO2-NPs dispersion effectively disrupt the formation of large aggregates. Thermogravimetric analysis of CNC: All thermogravimetric analysis (TGA) of powder materials were carried out under air atmosphere in a Libra F1 (Netzsch) thermobalance using a ramp of 10 ºC/min. Figure S7 confirms that CNC have been completely eliminated, as there is no residual mass after the experiment. Thermogravimetric analysis of the TiO2-CNC material: As the CNC residue is 0% at 800 ºC and approximately of 5% at 450 ºC, it can be deduced that CNC have been completely removed from the TiO2 matrix during the sintering step (450 ºC, 2 hours). The TiO2-CNC material reveals a 50% of residual mass, which confirms that all CNC were removed at a 1:1 TiO2 : CNC ratio (Figure S8). Differences in surface morphology between films prepared from commercial TiO2- P and TiO2-CNC(NH4OH): Figure S9 shows the results from the profilometry measurements of TiO2-P and TiO2- CNC(NH4OH) films. Both films displayed remarkable differences in surface characteristics. While TiO2-P film shows a smooth surface, the film obtained from the TiO2-CNC(NH4OH) dispersion exhibits a significant higher roughness. This disparity is clearly a consequence of the respective fabrication methodologies. In the case of the TiO2-P, screen printing was employed, allowing the particles to accommodate under the gentle pressure of the printing blade, resulting in a roughness of 110 nm (Figure S9a). By contrast, the spray coating process immobilized the TiO2-NPs upon contact with the hot substrate, leading to rapid droplet evaporation and the formation of a film with a pronounced roughness of 1300 nm (Figure S9b). Effect of CNC in the surface morphology. Comparison between films prepared from commercial TiO2-P and TiO2(NH4OH): To gain more insight into the effect of film processing, namely screen printing and spray coating, a comparison between TiO2 photoanodes of the same thickness (~3.5 µm) prepared by both techniques is herein shown. The screen-printed TiO2 photoanode was prepared with the GreatCell® paste, whereas the spray-coated TiO2 photoanode was fabricated from the TiO2(NH4OH) dispersions in order to discard the CNC effect upon sintering, as described in the main article. In terms of surface morphology, it is of great interest the study of such property according to the followed fabrication procedure. As commented before, the screen-printed films display low Rq values (Figure S10a) whereas the TiO2(NH4OH) ones show a higher roughness (Figure S10b). These differences directly arise from the film fabrication method followed. Furthermore, the addition of CNC clearly influences the morphology of the film, with the bare TiO2(NH4OH) film showing lower roughness (900 nm, Figure S10b) compared to the TiO2-CNC(NH4OH) one (1300 nm, Figure S9b). Gas physisorption of the TiO2 materials (N2 isotherms): To further explore the effect of the CNC on the macroporous structure of the TiO2-CNC(NH4OH) material used as photoanode, physisorption measurements were conducted on both bare TiO2-NPs and TiO2-CNC(NH4OH) powder materials after sintering. N2 adsorption−desorption at -196 °C (Quantachrome Autosorb-6B Instrument) was measured after sample degassing (250 °C, 4 h) to characterize the porous texture and the equivalent Brunauer−Emmett−Teller (BET) specific surface area (SBET). Figure S11 shows the N2 isotherms of the employed materials. Both materials exhibit type II isotherms according to the IUPAC classification, typical of non-porous solids.The isotherms (Figure S11) reveal an initial increase at low relative pressure values. When it comes to the intermediate region of the isotherms, it is important to note that the TiO2 CNC hybrid has a slightly increased adsorption due to the removal of the biopolymer during the thermal treatment. This probably refers to an enlarged separation between the solid TiO2 particles. A narrow hysteresis loop appears at very high relative pressures, around p/p0 = 0.9, which is commonly ascribed to the capillary condensation taking place within the interstitial pores between TiO2 particles. The BET specific surface area of the TiO2-CNC(NH4OH) powder material is marginally higher (42 m2/g) to the observed for the bare TiO2 nanoparticles (35 m2 /g), evidencingnot too much influence of the CNC in the final internal porosity. Pore size distribution (DFT and BJH methods): Pore size distribution has been calculated for both samples from their N2 adsorption isotherms using the density functional theory (DFT) (Figure S12) and the Barrett-JoynerHalenda (BJH) method (Figure S13), which uses the Kelvin model of pore filling. X-Ray diffraction: X-ray diffraction results of the employed materials, namely CNC (type-II), TiO2-NPs (anatase), TiO2-CNC, and the commercial TiO2 paste (GreatCell®) are shown in Figure S14. The diffractogram of CNC (type-II) is in agreement with literature. The synthesized TiO2-NPs exhibits the characteristic profile of anatase NPs, evidencing a comparable crystal phase composition and crystallite size to the commercial TiO2 paste. The average crystallite size of the employed TiO2-NPs is 25 nm,3 whereas the commercial TiO2 paste is composed of particles distributed in two sizes: 20 and 300 nm. Notably, the XRD analysis of the prepared TiO2-CNC(NH4OH) hybrid shows a combined pattern from TiO2 and CNC, not showing any additional peaks. Thermogravimetric analysis of the commercial TiO2 paste: The concentration of TiO2 in the commercial paste is somewhat higher (62%, Figure S15) to that of the TiO2-CNC. This mass loss is ascribed to the removal of alkylated celluloses from the paste. Scanning electron microscopy of photoanodes from commercial TiO2-P based: Figure S16 shows SEM images of the film obtained from TiO2 commercial paste. The TiO2-P based photoelectrode film displays a smooth surface, both before and after air sintering, despite having a similar content of cellulose derivatives (62 wt.% of TiO2) to our TiO2-CNC(NH4OH) hybrid (50 wt.%) (Figure S8). Photoelectrochemical characterization of the films prepared from TiO2(NH4OH) and commercial TiO2-P: Figure S17 displays the CV profiles of the TiO2(NH4OH) and TiO2-P films, both under dark and illumination. In the absence of light, the photoelectrodes exhibit the characteristic reversible redox behavior of TiO2 electrodes. A cathodic current is observed at more negative potentials, and a nearly symmetric positive current during the backward scan. The voltammograms exhibited an accumulation region at approximately -0.8 V, and a depletion region at higher potentials, -0.4 V. Under illumination conditions, both materials show similar photocurrent values (~ 46 µA·cm2). This observation is further supported by transient photocurrent measurements (Figure S18), which reveal slight differences between the two electrodes (from 32 µA·cm-2 to 43 µA·cm-2), highlighting the significant improvement of the TiO2 electrodes when using CNC and ammonia for their fabrication. 5-hour photocurrent measurements: Aiming to study the stability of the TiO2-CNC(NH4OH) and TiO2-P photoanodes, 5-hour experiments at a constant potential (0 V vs. Ag/AgCl) were performed (Figure S19). A photocurrent decay is observed in both cases, mainly caused by the blocking of the TiO2 active sites due to parasitic redox processes (see references 33, 34 and 35). Nevertheless, the TiO2-CNC(NH4OH) retained a higher PEC performance, even after 5 hours under operation conditions due to its specific morphology that arises from the CNC processing. Electrochemical impedance spectroscopy (EIS): Equivalent circuit: EIS spectra were analyzed according to the model circuit shown in Figure S20. Resistances (RS, Rct and Rsc) and constant phase elements, i.e. non-ideal capacitors with phase angle <90, (CPEdl and CPEsc) are calculated as model fitting parameters to the experimental data.-- Under a Creative Commons license BY-NC 3.0., TEM, size distribution and elemental analysis of CNC. Commercial TiO2 paste (TiO2-P): Film fabrication. Preparation of TiO2(NH4OH) and solid material. DLS and ζ-potential measurements. UV-Vis of the employed materials. TEM of the TiO2(NH4OH) material. Thermogravimetric analysis of CNC. Thermogravimetric analysis of the TiO2-CNC material. Differences in surface morphology between films prepared from commercial TiO2-P and TiO2-CNC(NH4OH). Effect of CNC in the surface morphology. Comparison between films prepared from commercial TiO2-P and TiO2(NH4OH). Physisorption of the TiO2 materials (N2 isotherms). Pore size distribution (DFT and BJH methods). X-Ray diffraction. Thermogravimetric analysis of the commercial TiO2 paste. SEM of photoanodes from commercial TiO2-P. Photoelectrochemical characterization of films prepared from TiO2(NH4OH) and commercial TiO2-P. 5-hour photocurrent measurements. Electrochemical impedance spectroscopy (EIS). Equivalent circuit. References., Financial support from Spanish MCIN/AEI/10.13039/501100011033 and “ERDF A way of making Europe” under project grants PID2022-139671OB-I00 and PID2020-120439-RA-I00, as well as by the Gobierno de Aragón (DGA) under projects T03_23R and E47_23R (Grupos de Investigación Reconocidos) is acknowledged. V. C. is thankful for his PhD contract funded by DGA (Ref. CUS/581/2020)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación Set de datos (Dataset)

Supporting information for Carbon nanomaterials-based inks and electrodes using chitin nanocrystals [Dataset]

  • Calvo Peña, Víctor
  • Martínez-Barón, Carlos
  • Vázquez Conejo, Benjamín
  • Domínguez Alfaro, Antonio
  • Paleo, A. J.
  • Villacampa, Belén
  • Ansón-Casaos, Alejandro
  • Maser, Wolfgang K.
  • Benito, Ana M.
  • González Domínguez, José Miguel
Under a Creative Commons BY 4.0 license., Additional experimental details, including the surface conditioning of CNMs and the characterization of CNMs and ChNCs along with their combinations, further information about the different CNM/ChNC inks behavior and their subsequent films, and calculations regarding the CNM concentration as well as the electrical conductivity and the standard electrochemical constant, 1. Surface conditioning of CNMs and characterization...........................................S3 2. Calculation of the CNMs concentration post centrifugation ..............................S6 3. Dynamic light scattering results of fresh and redispersed ChNCs.........................S7 4. Morphological characterization of ChNCs................................................................S8 5. Sheet resistance results of the SWCNT/ChNC films..........................................S10 6. Characterization of the CNM/ChNC dispersions...............................................S11 7. Purity index of SWCNT/ChNC dispersions ........................................................S13 8. Homocoagulation analysis of SWCNT/ChNC and MWCNT/ChNC dispersions..S15 9. Sheet resistance results of the CNM/ChNC films..............................................S16 10. SEM images of the CNM/ChNC films ................................................................S17 11. Calculation of the CNM/ChNC films electrical conductivity..............................S18 12. XPS measurements of the CNM/ChNC films..........................................................S19 13. Contact angle measurements of the CNM/ChNC films ....................................S22 14. Calculation of the standard electrochemical rate constant..............................S23 15. References ........................................................................................................S25, Financial support from Spanish MCINN/AEI/10.13039/501100011033 and “ERDF A way of making Europe” by the European Union under project grants PID2019-104272RB-C51, PID2020-120439RA-I00, and PID2022-139671OB-I00 as well from Spanish CSIC (PIE iniciación ref 202280I007) and from Gobierno de Aragón (DGA, Grupo Reconocido DGA-T03_23R and E47_23R) are acknowledged. V.C. and C.M.-B. thank the DGA for funding their PhD contracts (ref. CUS/581/2020 and CUS/621/2023). A.J.P. gratefully acknowledges support from the FCT-Foundation for Science and Technology by the 2020–2023 Project UIDB/00264/2020. A.D.A. acknowledges UPV/EHU for funding transferred by the European Union-Next Generation EU by the Margarita Salas fellowship (MARSA N° agreement 22/77)., Peer reviewed