Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 31
Encontrada(s) 1 página(s)

BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Performance Study of Graphene Oxide as an Antierosion Coating for Ornamental and Heritage Dolostone

  • Martínez García, Rebeca
  • González Campelo, David
  • Fraile Fernández, Fernando Jorge
  • Castañón García, Ana María
  • Caldevilla Domínguez, Pablo
  • Giganto Fernández, Sara
  • Ortiz Marqués, Almudena
  • Zelli, Flavia
  • Calvo Peña, Víctor
  • González Domínguez, José Miguel
  • Fernández Raga, María
doi:10.1002/admt.202300486 pertenece al artículo y doi:10.1002/admt.202370094 pertenece a la portada del número de la revista en la que se publicó dicho artículo., [EN] Concern for the perpetuation of stone monuments is deeply ingrained in humans; however, despite the attempts made in this field, there is still a great deal of effort needed to bring about advancements in the conservation of ornamental stone. Erosive agents, such as rain, extreme temperatures, and chemical and biological agents, threaten our stone heritage and gradually wear away buildings, sculptures, and other monuments found all around the world. Limestone and dolostone have been widely used throughout history, given their ease of extraction and workability. Nevertheless, these properties make them particularly vulnerable to the aforementioned erosive agents, for which the main solution at present is costly and time-consuming restoration. Given the scarcity of effective and durable agents to prevent the deterioration of ornamental and heritage stones, and as graphene oxide (GO) has recently shown impressive effectiveness for this task, this work will further explore the viability of GO as a protective coating for monumental dolostone. For this purpose, GO is sprayed over dolostone surfaces by water dispersion with no adjuvants. The coating performance is assessed in terms of thermal stress, optical inspection (structured light 3D scanner), colorimetry, leachate analysis, and electron microscopy. The main results show that spray-coated GO over stone surfaces creates a highly protective and durable barrier without altering their aesthetic qualities., SI, This research received funding from the University of León (ULE-PoC 2018) and Fundación General de la ULE y de la Empresa (FGULEM) under projects 2019/00149/001 and 2020. This research was also funded through an awarded MICINN project (PID2020-120439RA-I00). The authors are also thankful to the “Applied innovation against climate change and other aggressions on stone monuments (PRESERVARTE)” project of the Regional Ministry of Culture and Tourism of Castilla y León, which will be used to complement this research in the future.
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Adaptation of a Standard Method for Water Absorption Testing of Stone Materials: The Case of a Hydrophilic Protective Coating

  • Búrdalo Salcedo, Gabriel
  • Rodríguez, Indira
  • Fernández Raga, María
  • Fernández Raga, Sagrario
  • Rodríguez Fernández, Carlos
  • González Domínguez, José Miguel
Supplementary Materials: The following supporting information can be downloaded at https://www.mdpi.com/article/10.3390/ma16124228/s1, Video S1: Use of surgical drape to remove the excess water after the immersion step., [EN] The historical stone heritage that we inherit must be passed on to future generations, not only in the same conditions that we found it but, if possible, in better ones. Construction also demands better and more durable materials, often stone. The protection of these materials requires knowledge of the types of rocks and their physical properties. The characterization of these properties is often standardized to ensure the quality and reproducibility of the protocols. These must be approved by entities whose purpose is to improve the quality and competitiveness of companies and to protect the environment. Standardized water absorption tests could be envisaged to test the effectiveness of certain coatings in protecting natural stone against water penetration, but we found that some steps of these protocols neglect any surface modification of the stones, and hence may not be completely effective when a hydrophilic protective coating (i.e., graphene oxide) is present. In this work, we analyze the UNE 13755/2008 standard for water absorption and propose alternative steps to adapt the norm for use with coated stones. The properties of coated stones may invalidate the interpretation of the results if the standard protocol is applied as is, so here we pay special attention to the characteristics of the coating applied, the type of water used for the test, the materials used, and the intrinsic heterogeneity of the specimens, SI, This research received funding from the Universidad de León (ULE-PoC 2023) and “Fundación General de la ULE y de la Empresa (FGULEM)” under project 2019/00149/001, from the “Consejería de Educación-Desafíos 2020” and the “Consejería de Turismo-PRESERVARTE project” of the Region of Castilla y León, and the granted MICINN project (PID2020-120439RA-I00).
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Splash Erosion on Terraces, Does It Make a Difference If the Terracing Is Done before or after a Fire?

  • Fernández Raga, María
  • Martins, Martinho António dos Santos
  • Marcos Porras, Elena María
  • Fraile Laiz, Roberto
  • Keizer, Jan Jacob
This article belongs to the Section Soil and Hydrology, [EN] Terraces are a common Mediterranean feature influencing soils, slopes and subsurface hydrology; however, little is known about their impact on erosion processes, especially in humid regions. The purpose of this study was to assess how terracing after a fire affected erosion processes such as splash erosion. For 8 months, the study monitored splash erosion in three terraced plots, one plot under pre-fire conditions and the other two under post-fire conditions. Assessment of the impact of the terracing treatment in such plots was carried out by the installation of two different splash erosion quantitative systems: cups and funnels. An analysis of the splash data obtained in 17 rainfall events and meteorological data collected during each one of those periods was then performed. A significant positive correlation between the amount of rainfall and the splash erosion was observed. The two splash sampling systems show a high degree of concordance; however, the funnel-type model seems to be the most appropriate when it comes to preventing loss of splashed soil samples. The post-fire treatment with terracing leads to a smaller stability of surface soil aggregates, causing higher splash erosion rates. Sampling using the funnel system collects three times the amount of splashed soil than that collected by the cup system, although both systems correlate appropriately with the meteorological parameters, SI, This study has been supported by the projects EROSFIRE (POCTI/AGR/60354/2004) and EROSFIRE-II (PTDC/AGR-CFL/70968/2006), funded by the Portuguese Foundation for Science and Technology (FCT) with co-funding by FEDER through the POCI2010 Program. The Junta de Castilla y León has also contributed to this Project with Grant LE014A07, and the Spanish Ministry of Education with Grant TEC2007-63216. This research was also funded partially by project PID2020-120439RA-I00 financed by MCIN/AEI/10.13039/501100011033
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Study about the influence of diatoms on the durability of monumental limestone

  • Merino Maldonado, Daniel
  • Martínez García, Rebeca
  • Baladrón Blanco, Víctor
  • Prado Gil, Jesús de
  • Fraile Fernández, Fernando Jorge
  • Fernández Raga, María
  • Palencia Coto, María Covadonga
  • Juan Valdés, Andrés
[EN] This study focuses on the evaluation of the effects of a natural treatment of limestone rock samples using microalgae known as diatoms. A total of 18 samples in the form of 50 mm cubes, carved from limestone rock from Boñar (Spain), were analyzed, divided into experimental and control groups with an equal number of samples. Through various tests evaluating porosity, water absorption, frost resistance, and salt crystallization, diatom-treated samples were found to show higher porosity and water absorption compared with the control samples, especially when the entire sample was analyzed as a whole. However, in tests focusing on the surface side most exposed to biodeposition, reduced water absorption was observed in the treated samples, suggesting an improvement in their antiabsorption properties. In addition, slightly higher frost resistance was detected in the treated samples. For this reason, this study provides valuable information on the potential of diatoms to influence the properties of limestone rocks, which can serve as a basis for future research in this field and for the development of more effective treatments to improve the characteristics of rocks used in various applications, SI, This research was funded by the Spanish Ministry of Science and Innovation (MICINN) through project PID2020-120439RA-I00. The authors also wish to acknowledge the support of the project “Applied innovation against climate change and other aggressions on stone monuments (PRESERVARTE)”, funded by the Regional Ministry of Culture and Tourism of Castilla y León, which will serve to complement this research in the future. Additional support was provided by the Junta de Castilla y León through grant LE030G24
BULERIA. Repositorio Institucional de la Universidad de León
Publicación Artículo científico (JournalArticle)

Post-fire short-term treatments on a hillslope burnt soil: a case in the NW Iberian Atlantic transition region

  • Fernández Raga, María
  • Alcalde Aparicio, Sara
  • Serrano Bernardo, Francisco Antonio
  • Kavian, Ataollah
  • Cerdá, Artemi
  • Rodrigo Comino, Jesús
Funding for open access publishing: Universidad de Granada/CBUA., [EN] Forest fires pose a significant threat to rural areas, affecting ecosystems, property, infrastructure, and human lives. Effective post-fire management strategies are crucial for short-term ecosystem and community recovery. This study evaluated the effectiveness of three post-fire interventions in reducing soil erosion and runoff within a temperate Atlantic–transition climate, focusing on a shrubland hillslope near organic vineyards in Corullón, NW Spain, after a moderate-severity fire. The research aimed to (i) compare the effects of plowing, straw mulching, and no intervention (control) on post-fire soil recovery, and (ii) assess the cost-effectiveness and environmental impacts of these treatments. Ten experimental plots were randomly assigned to plowing (n = 4), straw mulching (n = 4), or control (n = 2). Seventeen rainfall events were monitored between 15 days and six months post-fire. Results showed no significant differences in erosion or runoff reduction among treatments. Natural vegetation recovery, assessed visually, was rapid across all plots, with erosion and runoff stabilizing within two months. These findings suggest that, under the specific conditions of this temperate climate and moderate fire severity, early intervention techniques may not be necessary. The study concludes that natural regeneration can be a viable and cost-effective post-fire management strategy in regions with favorable environmental conditions for soil recovery, potentially reducing the need for intensive interventions., SI
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Extraordinary protective efficacy of graphene oxide over the stone-based cultural heritage

  • González Campelo, D.
  • Fernández-Raga, María
  • Gómez Gutiérrez, Álvaro
  • Guerra Romero, M. I.
  • González Domínguez, José Miguel
8 figures.-- Supplementary information available., The deterioration of monumental stones is a common event occurring to our historical and cultural heritage, threatening the preservation of our social identity and its legacy to future generations. The prolonged effect of inclement weather is very harmful for particular stone materials such as limestone and dolomite, to which a truly effective and durable protective agent has not yet been found. Herein, an unprecedented performance of graphene oxide (GO) for the shielding of carbonated ornamental stones against environmental aggressions, namely intense rainfall and extreme temperatures, is demonstrated. A simple additive-free aqueous suspension of GO serves as the perfect coating, exceedingly preventing from any kind of wear or erosion after different climatic simulations. Additionally, the stones’ original aesthetics is not altered (a critical issue in monuments), together with an improvement in their mechanical properties, reasserting the unique potential of GO for conserving exposed stone-based monuments in an affordable, accessible, and revolutionary way., This research received funding from the Univerisdad de León (ULE-PoC 2018) and “Fundación General de la ULE y de la Empresa (FGULEM)” under projects 2019/00149/001 and 2020. J.M.G.-D. is grateful to the Spanish Ministry of Science, Innovation and Universities for his “Juan de la Cierva-Incorporación” research grant and associated research funds (IJCI-2016-27789). In loving memory of Prof. Jose L. García-Fierro, whose support with the XPS characterization was helpful for the development of this work. The authors also thank Mr. Adrián Domínguez Gutiérrez for his assistance during the photogrammetric processing of some samples. Invaluable assistance from Dr. Rebeca Martínez García and Dr. Sagrario Fernández Raga is highly indebted. Further research will be funded through a recently granted MICINN project (PID2020-120439RA-I00)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Synthesis and processing of nanomaterials mediated by living organisms

  • Calvo Peña, Víctor
  • González Domínguez, José Miguel
  • Benito, Ana M.
  • Maser, Wolfgang K.
5 figures, 1 scheme., Green living nanofactories: Nanomaterials (NMs) and nanocomposites are typically prepared by procedures that are incompatible with green chemistry and sustainability principles. But some living entities, from single cells to higher organisms, are able to synthesize and process NMs very efficiently under milder conditions. In this Minireview, the advances and prospects of this growing trend are discussed and summarized., Nanomaterials offer exciting properties and functionalities. However, their production and processing frequently involve complex methods, cumbersome equipment, harsh conditions, and hazardous media. The capability of organisms to accomplish this using mild conditions offers a sustainable, biocompatible, and environmentally friendly alternative. Different nanomaterials such as metal nanoparticles, quantum dots, silica nanostructures, and nanocellulose are being synthesized increasingly through living entities. In addition, the bionanofabrication potential enables also the in situ processing of nanomaterials inside biomatrices with unprecedented outcomes. In this Minireview we present a critical state-of-the-art vision of current nanofabrication approaches mediated by living entities (ranging from unicellular to higher organisms), in order to expand this knowledge and scrutinize future prospects. An efficient interfacial interaction at the nanoscale by green means is within reach through this approach., Financial support from Spanish MICINN/AEI under projects PID2019-104272RB-C51/AEI/10.13039/501100011033 and PID2020-120439RA-I00, as well as from Gobierno de Aragón (DGA, Grupo Reconocido DGA-T03_20R) is acknowledged. V.C. gratefully thanks the DGA for funding his PhD contract (Ref. CUS/581/2020)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of nanocellulose polymorphism on electrochemical analytical performance in hybrid nanocomposites with non-oxidized single-walled carbon nanotubes

  • Dortez, Silvia
  • Sierra, Tania
  • Álvarez Sánchez, Miguel Ángel
  • González Domínguez, José Miguel
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • Crevillén, Agustín G.
  • Escarpa, Alberto
4 figures, 2 tables., Two cellulose nanocrystals/single-walled carbon nanotube (CNC/SW) hybrids, using two cellulose polymorphs, were evaluated as electrochemical transducers: CNC type I (CNC-I/SW) and CNC type II (CNC-II/SW). They were synthesized and fully characterized, and their analytical performance as electrochemical sensors was carefully studied. In comparison with SWCNT-based and screen-printed carbon electrodes, CNC/SW sensors showed superior electroanalytical performance in terms of sensitivity and selectivity, not only in the detection of small metabolites (uric acid, dopamine, and tyrosine) but also in the detection of complex glycoproteins (alpha-1-acid glycoprotein (AGP)). More importantly, CNC-II/SW exhibited 20 times higher sensitivity than CNC-I/SW for AGP determination, yielding a LOD of 7 mg L−1.These results demonstrate the critical role played by nanocellulose polymorphism in the electrochemical performance of CNC/SW hybrid materials, opening new directions in the electrochemical sensing of these complex molecules. In general, these high-active-surface hybrids smartly exploited the preserved non-oxidized SW conductivity with the high aqueous dispersibility of the CNC, avoiding the use of organic solvents or the incorporation of toxic surfactants during their processing, making the CNC/SW hybrids promising nanomaterials for electrochemical detection following greener approaches., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. This work has been financially supported by the TRANSNANOAVANSENS program from the Community of Madrid (P2018/NMT-4349), and the Spanish Ministry of Economy and Competitiveness (CTQ2017-86441-C2-1-R). Additional funding support was from Spanish MINEICO/MICINN under project with references ENE2016-79282-C5-1-R (AEI/FEDER/UE), PID2019-104272RB-C51/AEI/10.13039/501100011033, and PID2020-120439RA-I00. Funding support from Gobierno de Aragón (Grupo Reconocido T03_20R) is also acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Nanocristales de quitina y sus híbridos funcionales con potenciales aplicaciones en energía y sostenibilidad

  • Calvo Peña, Víctor
  • Ulcuango, Matías
  • González Domínguez, José Miguel
  • Benito, Ana M.
  • Maser, Wolfgang K.
Resumen de la comunicación oral presentada en la 9ª Jornada de Jóvenes Investigadores de Física y Química de Aragón, celebrada el 16 de diciembre de 2021 en Zaragoza., Los biopolímeros nanoestructurados tienen propiedades excepcionales, se extraen de fuentes naturales y tienen el potencial de sustituir plásticos de fuentes no sostenibles, como el petróleo. Estas cualidades se deben a su tamaño en la nano-escala (entre 1 y 100 nm), siendo el más investigado la nanocelulosa en sus distintas variedades [1,2]. La quitina es el segundo biopolímero más abundante tras la celulosa y se encuentra en distintos seres vivos, por ejemplo, en los exoesqueletos de crustáceos y artrópodos, aportando rigidez y dureza [3]. La quitina se puede transformar en nanocristales de quitina (NCQ) a través de un proceso de hidrólisis ácida [4]. Distintas aplicaciones de los NCQ son la estabilización eficiente en agua de nanomateriales de carbono, la preparación de aerogeles o su uso como refuerzo de otros materiales [5,6]. En este trabajo se presenta un método optimizado para la obtención de NCQ dispersos en agua con un rendimiento superior al 60% frente al 30% del método inicial. Se han caracterizado por diversas técnicas como difracción de rayos X, termogravimetría o microscopía de transmisión electrónica. Se ha probado también la capacidad de redispersión de los NCQ tras liofilizarlos, obteniendo una dispersión de calidad similar tras un proceso sencillo basado en ultrasonidos, lo cual no sucede con otros biopolímeros nanoestructurados, como los nanocristales de celulosa. Se ha probado el uso de NCQ como dispersante en tintas tanto de nanotubos de carbono como de nanofibras de carbono y su integración in situ y ex situ como refuerzo en xerogeles de nanocelulosa bacteriana. En definitiva, la presente comunicación demuestra el enorme potencial de NCQ como agente dispersante, refuerzo, y aditivo sostenible para obtener desde una perspectiva verde una variedad de nanomateriales compuestos., Financiación del MICINN/AEI bajo los proyectos PID2019-104272RB-C51/ AEI/10.13039/501100011033 y PID2020-120439RA-I00, y del Gobierno de Aragón (DGA, Grupo Reconocido DGA-T03_20R). Víctor C. agradece a la DGA por la financiación de su contrato predoctoral (Ref. CUS/581/2020).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The use of high-speed cameras as a tool for the characterization of raindrops in splash laboratory studies

  • Fernández-Raga, María
  • Cabeza-Ortega, Marco
  • González-Castro, Víctor
  • Peters, Piet
  • Commelin, Meindert
  • Campo, Julián
© 2021 by the authors., Measuring the characteristics of raindrops is essential for different processes studies. There have been many methods used throughout history to measure raindrops. In recent years, automatic image recognition and processing systems have been used with high-speed cameras to characterize rainfall by obtaining the spectrum of droplet sizes and their speeds and thus being able to use this technology to calibrate rainfall simulators. In this work, two phases were carried out: in the first one, individual drops with terminal speeds of different sizes were measured and processed both in speed and in shape with a high-speed camera; and in the second phase, a calibration procedure was designed but in multidrop images, determining the characteristics of the drops produced by a rain simulator. According to results, the real shape of each drop depending on the size was determined, from round to ovaloid shapes, and the terminal velocity of water drops with different sizes was measured. Based on the rain images used to calibrate a rainfall simulator, it was observed that, with a higher intensity of rain, the drops produced were smaller, which contrasts with real rain, in which just the opposite happens. This calibration evaluates their resemblance to reality, calculates the real kinetic energy of the rain they produce and see if they can be used to model events in nature., This research was fund by project PID2020-120439RA-I00 financed by MCIN/ AEI /10.13039/501100011033.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Preparation of cellulose nanocrystals: controlling the crystalline type by one-pot acid hydrolysis

  • Calvo Peña, Víctor
  • Álvarez Sánchez, Miguel Ángel
  • Güemes, Lucas
  • Martínez-Barón, Carlos
  • Baúlde, Sandra
  • Criado, A.
  • González Domínguez, José Miguel
  • Maser, Wolfgang K.
  • Benito, Ana M.
6 figures.-- Supplementary information available., Cellulose nanocrystals (CNCs) have aroused increasing interest owing to their renewable origin and excellent properties derived from their size and morphology. Based on their chain orientation, CNCs can be prepared as two main allomorphs (I or II). However, achieving pure CNC allomorphs still requires enhanced control on the CNCs synthesis process and improved understanding of the involved reaction parameters. In this work, we study in detail a set of parameters for CNC synthesis using one-pot acid hydrolysis and evaluate their influence on the outcome with respect to yield, purity, and repeatability. We also demonstrate that a fast, nondestructive, and accurate methodology based on dynamic light scattering is an efficient alternative to the usual structural analysis of the synthesis outcome. Finally, we provide an improved protocol to reliably obtain each allomorph with mass yields of 25% for type I and 40% for type II. Emphasis is put on the reduction of the environmental impact and the overall preparation time., Financial support from Spanish MICINN/AEI under Projects PID2019-104272RB-C51/AEI/10.13039/501100011033 and PID2020-120439RA-I00, as well as from Gobierno de Aragón (DGA, Grupo Reconocido DGA-T03_20R) is acknowledged. V.C. and M.A.A. gratefully thank the DGA for funding their Ph.D. contracts (ref. CUS/581/2020 and ref. IIU/796/2019). A.C. thanks MICINN for his research grant (Ramon y Cajal No. RYC2020-030183-I). S.B. thanks MICINN for funding (PID2020-117885GA-I00)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Statistical study of the effectiveness of surface application of graphene oxide as a coating for concrete protection

  • Antolín Rodríguez, Andrea
  • Merino Maldonado, Daniel
  • Rodríguez González, Álvaro
  • Fernández-Raga, María
  • González Domínguez, José Miguel
  • Juan-Valdés, Andrés
  • García-González, Julia
5 figures, 2 tables.-- This article belongs to the Special Issue "Surface Biotreatment of Building Materials"., Improving the protection of concrete by applying graphene oxide (GO) as a surface treatment has become the objective of the present study. This study focuses on performing a statistical analysis to study different levels of GO application as an exterior coating, thus observing the effectiveness of the coating and the optimization of the treatment material for concrete protection. Four tests were performed to define concrete durability, such as pressurized water penetration, capillary absorption, freeze-thaw resistance and carbonation resistance. The results showed an increase in concrete durability with any level of GO application on the surface, considering that the optimum amount of application for water impermeability and freeze-thaw resistance is 26.2 µg/cm2, since it was possible to reduce pressurized water penetration by 45%, capillary water absorption by 57% and freeze-thaw detachment by 25%. However, the optimum application rate for carbonation resistance is 52.4 µg/cm2, reducing carbonation by almost 60%. In conclusion, if the concrete is going to be exposed to less aggressive environments, the application of a mild surface coating of GO is sufficient for its protection, and if the concrete is going to be exposed to more aggressive environments, it is necessary to increase the amount of GO. The performance of GO as a coating significantly increased the degree of protection of the concrete, increasing its service life and proving to be a promising treatment for concrete surface protection., A.A.R. greatfully acknowledge to Aid from the Junta de Castilla y Leon to finance the pre-doctoral hiring of research personnel, co-financed by the European Social Fund, resolved in the ORDER EDU/875/2021, of July 13. D.M.M. greatfully acknowledge to Aid from the Junta de Castilla y Leon to finance the pre-doctoral hiring of research personnel, co-financed by the European Social Fund, resolved in the ORDEN EDU/601/2020, of July 3. M.F.R and J.M.G.-D. greatfully acknowledge Spanish Ministry of Science and Innovation (MICINN) and the Spanish Research Agency (AEI) for the financial support provided by the NANOSHIELD project (PID2020-120439RA-I00)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Performance study of graphene oxide as an antierosion coating for ornamental and heritage dolostone

  • Martínez García, Rebeca
  • González Campelo, D.
  • Fraile-Fernández, Fernando J.
  • Castañón, Ana M.
  • Caldevilla, Pablo
  • Giganto, Sara
  • Ortiz Marqués, Almudena
  • Zelli, Flavia
  • Calvo Peña, Víctor
  • González Domínguez, José Miguel
  • Fernández-Raga, María
9 figures, 2 tables.-- Supplementary information available., Concern for the perpetuation of stone monuments is deeply ingrained in humans; however, despite the attempts made in this field, there is still a great deal of effort needed to bring about advancements in the conservation of ornamental stone. Erosive agents, such as rain, extreme temperatures, and chemical and biological agents, threaten our stone heritage and gradually wear away buildings, sculptures, and other monuments found all around the world. Limestone and dolostone have been widely used throughout history, given their ease of extraction and workability. Nevertheless, these properties make them particularly vulnerable to the aforementioned erosive agents, for which the main solution at present is costly and time-consuming restoration. Given the scarcity of effective and durable agents to prevent the deterioration of ornamental and heritage stones, and as graphene oxide (GO) has recently shown impressive effectiveness for this task, this work will further explore the viability of GO as a protective coating for monumental dolostone. For this purpose, GO is sprayed over dolostone surfaces by water dispersion with no adjuvants. The coating performance is assessed in terms of thermal stress, optical inspection (structured light 3D scanner), colorimetry, leachate analysis, and electron microscopy. The main results show that spray-coated GO over stone surfaces creates a highly protective and durable barrier without altering their aesthetic qualities., This research received funding from the University of León (ULE-PoC 2018) and Fundación General de la ULE y de la Empresa (FGULEM) under projects 2019/00149/001 and 2020. This research was also funded through an awarded MICINN project (PID2020-120439RA-I00). The authors are also thankful to the “Applied innovation against climate change and other aggressions on stone monuments (PRESERVARTE)” project of the Regional Ministry of Culture and Tourism of Castilla y León, which will be used to complement this research in the future., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Adaptation of a standard method for water absorption testing of stone materials: the case of a hydrophilic protective coating

  • Búrdalo, Gabriel
  • Rodríguez, Indira
  • Fernández-Raga, María
  • Fernández Raga, Sagrario
  • Rodríguez Fernández, Carlos
  • González Domínguez, José Miguel
10 figures.-- Supplementary material: Video S1: Use of surgical drape to remove the excess water after the immersion step., The historical stone heritage that we inherit must be passed on to future generations, not only in the same conditions that we found it but, if possible, in better ones. Construction also demands better and more durable materials, often stone. The protection of these materials requires knowledge of the types of rocks and their physical properties. The characterization of these properties is often standardized to ensure the quality and reproducibility of the protocols. These must be approved by entities whose purpose is to improve the quality and competitiveness of companies and to protect the environment. Standardized water absorption tests could be envisaged to test the effectiveness of certain coatings in protecting natural stone against water penetration, but we found that some steps of these protocols neglect any surface modification of the stones, and hence may not be completely effective when a hydrophilic protective coating (i.e., graphene oxide) is present. In this work, we analyze the UNE 13755/2008 standard for water absorption and propose alternative steps to adapt the norm for use with coated stones. The properties of coated stones may invalidate the interpretation of the results if the standard protocol is applied as is, so here we pay special attention to the characteristics of the coating applied, the type of water used for the test, the materials used, and the intrinsic heterogeneity of the specimens., This research received funding from the Universidad de León (ULE-PoC 2023) and “Fundación General de la ULE y de la Empresa (FGULEM)” under project 2019/00149/001, from the “Consejería de Educación-Desafíos 2020” and the “Consejería de Turismo-PRESERVARTE project” of the Region of Castilla y León, and the granted MICINN project (PID2020-120439RA-I00)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Otros (Other)

Responsible heritage protection actions

  • Fernández-Raga, María
  • González Domínguez, José Miguel
  • Caldevilla, Pablo
  • Búrdalo, Gabriel
  • Ortiz Marqués, Almudena
  • Martínez García, Rebeca
  • Fraile-Fernández, Fernando J.
  • Rodríguez, Indira
2 figures,1 table.-- Conference paper presented at the EURECA-PRO Conference - 2022 , held in León (Spain) from October 19 to October 21, 2022.-- Editorial policy for use: https://www.springernature.com/gp/open-research/policies/accepted-manuscript-terms, In recent decades, interest in maintaining and conserving cultural assets has grown and there has been greater investment in the conservation of historical heritage. Developing a good methodology for action is key to guaranteeing adequate preservation of cultural assets. With this in mind, the Spanish Historical Heritage Institute convened a conference in 2002 to try to define basic criteria to guide the different phases of the intervention process in stone materials in all stages of stone conservation: cleaning, consolidation and protection. Carrying out efficient protection of monuments in the traditional way focuses efforts only on how it affects the property, but not on the collateral impact it may have on the environment, or how the effects of climate change may alter its functionality. Thus, a more multidisciplinary test design is needed, with a mandatory laboratory simulation phase under simulated rainfall that represents the increased environmental aggressiveness expected in the near future due to climate change. Hence, water becomes a means to simulate these future conditions, but also a way to explore the effects on rivers and groundwater near the points where the monuments will be treated. Since fresh water is one of the resources that is expected to become scarce in the short term, we intend to carry out responsible tests that take into account both aspects: saving water use and water pollution. Combining the conservation of monuments and environmental responsibility, it will be shown how it is possible to carry out research to achieve a natural product that serves as a sustainable coating for monuments of stone material that is durable but that reduces the environmental impact both in the selection of the product and in the experimental phase, as well as in its operation after application., This research received funding from the Universidad de León (ULE-PoC 2018) and “Fundación General de la ULE y de la Empresa (FGULEM)” under project 2019/00149/001, from the “Consejería de Educación-Desafíos 2020” and the “Consejería de Turismo-PRESERVARTE project” of the Region of Castilla y León, and the granted MICINN project (PID2020-120439RA-I00)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Oil-in-water pickering emulsions stabilized with nanostructured biopolymers: a venue for templating bacterial cellulose

  • Calvo Peña, Víctor
  • Fuentes Varela, Laura
  • Berdejo, Daniel
  • González Domínguez, José Miguel
  • Maser, Wolfgang K.
  • Benito, Ana M.
Pickering emulsions (PEs) differ from conventional emulsions in the use of solid colloidal particles as stabilizing agents instead of traditional amphiphilic molecules. Nanostructured biopolymers (NBs) emerge as a promising alternative for PE stabilization owing to their remarkable biocompatibility, abundant availability, and low cost. To explore this potential, a study is herein presented, in which cellulose nanocrystals (CNCs), both type I and type II allomorphs, and chitin nanocrystals (ChNCs) were used for stabilizing oil-in-water PEs prepared by the use of ultrasound. Sunflower oil was selected as the oil phase as it offers the advantages of being edible, renewable, and inexpensive. By utilizing ζ-potential, static light diffraction, and visual observations, we determined the optimal oil/water ratio for each type of NB to obtain stable emulsions after 14 days. The optimized PEs were used to form bacterial nanocellulose composites through emulsion templating. To our knowledge, this study represents a pioneering work in exploiting oil-in-water PEs for this approach. Additionally, it entails the first utilization of nonmercerized type II CNCs as stabilizers for PEs, while also establishing a direct comparison among the most relevant NBs. The resulting composites exhibited a unique morphology, composed of larger pores compared to standard bacterial nanocellulose aerogels. These findings highlight the notable potential of NBs as stabilizers for PEs and their ability to generate green nanocomposites with tailored properties., This research was funded by Spanish MICINN/AEI under projects PID2019-104272RB-C51/AEI/10.13039/501100011033 and PID2020-120439RA-I00, from Spanish CSIC (PIE iniciación ref. 202280I007), and support from Gobierno de Aragón (DGA, Grupo Reconocido DGA-T03_23R) is acknowledged. Víctor Calvo thanks the DGA for funding their Ph.D. contracts (Ref. CUS/581/2020)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación Set de datos (Dataset)

Supplementary materials for Oil-in-water pickering emulsions stabilized with nanostructured biopolymers: a venue for templating bacterial cellulose [Dataset]

  • Calvo Peña, Víctor
  • Fuentes Varela, Laura
  • Berdejo, Daniel
  • González Domínguez, José Miguel
  • Maser, Wolfgang K.
  • Benito, Ana M.
Chemical structure of the nanostructured biopolymers: Figure S1. Chemical structure of cellulose nanocrystals (A) and chitin nanocrystals (B).-- Polydispersity results of nanostructured biopolymers: Figure S2. Polydispersity indexes of the NBs (CNCs I, CNCs II and ChNCs) in water with different NaCl concentrations.-- Evolution of the visual appearance of PEs: Figure S3. Evolution over time of the PEs made with CNCs I. The images were used to determine the creaming index. Figure S4. Evolution over time of the PEs made with CNCs II. The images were used to determine the creaming index. Figure S5. Evolution over time of the PEs made with ChNCs. The images were used to determine the creaming index.-- BNC production with ChNCs without PEs: Figure S6. BNC culture media without ChNCs (left) and two different ChNCs concentrations (center and right) after 14 days since inoculation. It can be observed that ChNCs precipitate, what reduces the ChNCs incorporation in the BNC composites.-- BNC hydrogels prepared with emulsified culture media: Figure S7. BNC hydrogels prepared with emulsified culture media after cleaning.-- Under Creative Commons Attribution (CC BY) license., Chemical structure of the nanostructured biopolymers. Polydispersity results of nanostructured biopolymers. Evolution of the visual appearance of PEs. BNC production with ChNCs without PEs. BNC hydrogels prepared with emulsified culture media., This research was funded by Spanish MICINN/AEI under projects PID2019-104272RB-C51/AEI/10.13039/501100011033 and PID2020-120439RA-I00, from Spanish CSIC (PIE iniciación ref. 202280I007), and support from Gobierno de Aragón (DGA, Grupo Reconocido DGA-T03_23R) is acknowledged. Víctor Calvo thanks the DGA for funding their Ph.D. contracts (Ref. CUS/581/2020)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The aqueous processing of carbon nanofibers via cellulose nanocrystals as a green path towards e-textiles with n-type thermoelectric behaviour

  • Calvo Peña, Víctor
  • Paleo, A. J.
  • González Domínguez, José Miguel
  • Muñoz, Edgar
  • Krause, Beate
  • Pötschke, Petra
  • Maser, Wolfgang K.
  • Benito, Ana M.
9 figures, 2 tables.-- Supplementary information available., Cellulose nanocrystals (CNCs) are a nanostructured biopolymer with unique properties, such as high strength and water stability. These properties make CNCs ideal for diverse applications, including dispersing agents for hydrophobic carbon nanomaterials in water. Specifically, carbon nanomaterials can be integrated into textiles to produce flexible electronic wearables with excellent performance. However, the necessary prerequisite of achieving stable liquid dispersions of these carbon nanomaterials, such as nanofibers (CNFs) typically involves the use of organic solvents or high concentrations of hazardous surfactants in water. Thus, in this study, for the first time, CNCs were successfully used to prepare CNFs aqueous dispersions, referred to as inks, at CNF concentrations up to 0.7 g L−1. As a proof of principle, these inks were then integrated into a cotton fabric using a facile dip coating and drying strategy, resulting in an e-textile with a negative Seebeck coefficient. Furthermore, a theoretical model was developed to describe the nonlinear Seebeck coefficient of the nanocomposite textile, shedding light on the physics governing the electrical conductivity and Seebeck coefficient over a temperature range from 30 °C to 100 °C. These promising results pave the way towards the development of environmentally friendly and durable CNF aqueous dispersions and wearable e-textiles., Financial support from Spanish MCIN/AEI under projects PID2019-104272RB-C51/AEI/10.13039/501100011033 and PID2020-120439RA-I00, from Spanish CSIC (PIE iniciación ref. 202280I007), as well as from Gobierno de Aragón (DGA, Grupo Reconocido DGA-T03_23R) is acknowledged. Vícto Calvo thanks the DGA for funding his PhD contract (Ref. CUS/581/2020). Antonio J. Paleo gratefully acknowledges support from FCT-Foundation for Science and Technology by the “plurianual” 2020–2023 Project UIDB/00264/2020, and European COST Action EsSENce CA19118 for its support with the Short Term Scientific Mission (STSM) grant E-COST-GRANT-CA19118-0ed3a197 at IPF (Dresden). E. Muñoz acknowledges funding from ANID ANILLO ACT/192023 and Fondecyt No 1230440., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación Set de datos (Dataset)

Appendix A. Supplementary data for The aqueous processing of carbon nanofibers via cellulose nanocrystals as a green path towards e-textiles with n-type thermoelectric behaviour [Dataset]

  • Calvo Peña, Víctor
  • Paleo, A. J.
  • González Domínguez, José Miguel
  • Muñoz, Edgar
  • Krause, Beate
  • Pötschke, Petra
  • Maser, Wolfgang K.
  • Benito, Ana M.
Under a Creative Commons license BY-NC-ND 4.0 Deed., Synthesis of cellulose nanocrystals: Cellulose nanocrystals (CNCs) were synthesized following the protocol described in two previous publications.[1,2] 10 g of microcrystalline cellulose (MCC) (Sigma-Aldrich, ref 310697) were dispersed in 45 ml of ultrapure water using an ultrasound bath (45 kHz) for 5 min. Then, 45 ml of H2SO4 98 wt% (Labkem, ref SUAC-00A) were added dropwise to the mixture (externally cooled in an ice/water bath at 0 °C) reaching a final H2SO4 concentration of 64 wt%. This addition was performed fast (less than 5 min) and with magnetic stirring to obtain type I CNCs or slow (longer than 100 min) and with high shear mixing to obtain type II CNCs.[1] After that, the mixture was put in a heating plate at 70°C for 10 minutes for type I CNCs or at ambient temperature for 1 hour for type II CNCs. The reaction was stopped by diluting in 1 liter of ultrapure water at 4°C, also to increase the pH, and the mixture was left decanting overnight at 4°C. The bottom sediment was dialyzed against ultrapure water until a neutral pH was achieved, using specific dialysis membranes (Merck, average flat width 33 mm, ref D9652-100FT). The neutralized dispersions were subjected to centrifugation/re-dispersion cycles at 9000 rpm (9327 rcf) for 1 min to keep only the nanocrystals. The average mass yield and the concentration (Table S1) were determined by lyophilization of 3 aliquots of 30 mL of the CNCs dispersions. The hydrodynamic radii, polydispersity, and ζ-potential were measured using a Malvern Nano ZS instrument, and the mean values of these parameters are presented in Table S1. The CNCs in solid were measured by a Bruker D8 Advance X-Ray diffractometer using a Cu tube as the X-ray source (λ Cu Kα = 1.54 Å), a tube voltage of 40 kV, and a current of 40 mA. The X-Ray diffraction patterns of the prepared CNCs (Fig. S1) confirmed the different presence of the characteristic planes of type I or type II cellulose.--, Synthesis of cellulose nanocrystals: Table S1. Mean values of the characterization results of type I and type II CNCs dispersions. Fig. S1. X-ray diffraction profiles of type I (red) and type II (blue) CNCs. Surface resistivity of n-type thermoelectric cotton textiles as a function of the number of dip-coating cycles: Fig. S2. Surface resistivity (Rsh) of nanocomposite textiles from 1 to 10 immersion cycles with equivalent inks, but different immersion methodology: regular (red) and using a complementary ultrasounds bath treatment for 5 min (black). Measured with an in-line 4-point probe configuration. Error bars show standard deviation of at least 3 repetitions. SEM images of the surface of original and washed CWF@CNF textile samples: Fig. S3. SEM images of the surface of original and washed CWF@CNF textile samples at different magnifications (a) CWF@CNF, (b) CWF@CNF W30 and (c) CWF@CNF W45. Model proposed for describing the nonlinear Seebeck of CNFs and CWF@CNF: The model presented in this work represents the combination of two physical mechanisms occurring in parallel: S(T)=S_met (T)+S_imp (T) (1). Power factor and estimative figure of merit of unwashed and washed samples and CNFs: Table S2. Thermoelectrical properties of dip-coated textiles and carbon nanofibers. References., Financial support from Spanish MCIN/AEI under projects PID2019-104272RB-C51/AEI/10.13039/501100011033 and PID2020-120439RA-I00, from Spanish CSIC (PIE iniciación ref. 202280I007), as well as from Gobierno de Aragón (DGA, Grupo Reconocido DGA-T03_23R) is acknowledged. Vícto Calvo thanks the DGA for funding his PhD contract (Ref. CUS/581/2020). Antonio J. Paleo gratefully acknowledges support from FCT-Foundation for Science and Technology by the “plurianual” 2020–2023 Project UIDB/00264/2020, and European COST Action EsSENce CA19118 for its support with the Short Term Scientific Mission (STSM) grant E-COST-GRANT-CA19118-0ed3a197 at IPF (Dresden). E. Muñoz acknowledges funding from ANID ANILLO ACT/192023 and Fondecyt No 1230440., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Performance of graphene oxide as a water-repellent coating nanomaterial to extend the service life of concrete structures

  • Antolín Rodríguez, Andrea
  • Merino Maldonado, Daniel
  • González Domínguez, José Miguel
  • Fernández-Raga, María
  • Morán del Pozo, J. Mª.
  • García-González, Julia
  • Juan-Valdés, Andrés
10 figures, 4 tables., Surface treatments help to protect the built heritage against damage (environmental, accidental, etc.), reducing repair and restitution costs and increasing the useful life of building materials. The use of nanomaterials is currently the most important field of research in surface treatment technology for the preservation of building materials and, more specifically, to improve their durability and prevent their deterioration, extending their useful life. This paper studies the influence of a graphene oxide (GO) suspension as a surface treatment on the properties of concrete. The results indicate that, at best, surface treatment with GO can decrease both the water absorption and capillary absorption of concrete by about 15 %. The increase in the amount of GO deposited as a surface treatment leads to a further reduction in concrete water absorption. It is shown that, at best, GO coating also reduces water penetration at low and high pressures by approximately 20 % and 60 %, respectively. In addition, scanning electron microscopy analysis shows that GO surface treatment facilitates the hydration process and densifies the concrete microstructure. A simple aqueous suspension of GO is revealed as a tool with a high potential to protect concrete surfaces in a fast and cost-effective way, thanks to the easy application by spraying and the small amount of material needed to obtain great results., This work was supported by the Junta de Castilla y León through the “Ayudas para financiar la contratación predoctoral de personal investigador”, cofinanced by the European Social Fund and resulting in ORDEN EDU/875/2021 and ORDEN EDU/601/2020. José Miguel González-Domínguez and María Fernández-Raga greatly acknowledge the Spanish Ministry of Science and Innovation (MICINN) for the funded project “Nanoshield” (PID2020-120439RA-I00), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Metal-free nanostructured-carbon inks for a sustainable fabrication of zinc/air batteries: From ORR activity to a simple prototype

  • Santos, Florencio
  • Lorca, Sebastián
  • González Martínez, Juan F.
  • Urbina, Antonio
  • Álvarez Sánchez, Miguel Ángel
  • González Domínguez, José Miguel
  • García-Bordejé, José Enrique
  • Ansón-Casaos, Alejandro
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • Fernández Romero, Antonio J.
5 figures, 1 table.-- Under a Creative Commons license CC-BY 4.0., Zinc/air batteries are convenient energy storage devices for both small and massive applications. While future perspectives indicate the need for low-cost components and sustainable fabrication processes, the battery performance is in part controlled by the kinetics of the oxygen reduction reaction (ORR), which typically involves transition metals as catalysts. In this context, we prepare a series of metal-free water-based carbon inks, which are tested for their catalytic performance, once deposited on a gas-diffusion substrate, in the air cathode of a simple battery prototype. The inks contain a variety of well-defined carbon nanomaterials and additives, exhibiting different physicochemical properties that critically influence the interaction with the gas diffusion hydrophobic substrate. The intrinsic ORR catalytic activity of the ink material is also analyzed on a glassy carbon electrode by the rotating ring-disc electrode (RRDE) method and specific capacitance measurements. The discharge capacity on our zinc/air battery prototype correlates well with the intrinsic catalytic activity in the RRDE. However, only the activity in the RRDE does not actually assure the performance on the commercial cathode of the prototype, since other chemical compatibility issues play a role. Thus, we highlight the importance of catalyst testing, not only on the RRDE but also under realistic device conditions., This study received financial support from Spanish MICINN under projects PID2019-104272RB-C51, C55AEI/10.13039/501100011033, PID2020-120439-RA-I00, Diputación General de Aragón under project T03_23R (Grupo Reconocido), and Fundación Séneca (Región de Murcia, Spain; Reference: 20985/PI/18). The authors also appreciate the financial support provided by the MICINN and the European Union “NextGenerationEU/PRTR” through the project TED2021–130334B-I00., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Microstructural, durability and colorimetric properties of concrete coated with a controlled application of graphene oxide

  • Antolín Rodríguez, Andrea
  • Merino Maldonado, Daniel
  • Fernández-Raga, María
  • González Domínguez, José Miguel
  • Morán del Pozo, J. Mª.
  • García-González, Julia
  • Juan-Valdés, Andrés
13 figures, 3 tables., The present work analyzes how an aqueous suspension of graphene oxide (GO), as a surface treatment, can influence the properties of conventional concrete. The results show that the application of a GO surface coating on concrete improves its resistance to carbonation and chloride ion penetration, and also increases its electrical resistivity. In the best case, the GO coating can reduce carbonation by 40% and chloride ion diffusion by 75%. An increase of up to 75% in concrete resistivity was also achieved. The application of GO promotes the hydration process and densifies the microstructure of the concrete surface, and this is verified by scanning electron microscopy analysis. In addition, no color modification occurred after application of the treatment., Andrea Antolín-Rodríguez and Daniel Merino-Maldonado would like to thank the Junta de Castilla y León for the support granted through the “Ayudas para financiar la contratación predoctoral de personal investigador”, cofinanced by the European Social Fund and resulting in ORDEN EDU/875/2021 and ORDEN EDU/601/2020. José Miguel González-Domínguez and María Fernández-Raga greatly acknowledge the Spanish Ministry of Science and Innovation (MICINN) for the funded project “Nanoshield” (PID2020-120439RA-I00)
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Towards sustainable TiO2 photoelectrodes based on cellulose nanocrystals as a processing adjuvant

  • Martínez-Barón, Carlos
  • Calvo Peña, Víctor
  • Hernández-Ferrer, Javier
  • Villacampa, Belén
  • Ansón-Casaos, Alejandro
  • González Domínguez, José Miguel
  • Maser, Wolfgang K.
  • Benito, Ana M.
8 figures, 2 tables.-- Supplementary information available., Photoelectrodes of TiO2 in the form of films are commonly fabricated using screen printing techniques, employing viscous commercial TiO2 pastes. However, these pastes comprise environmentally unfriendly, multicomponent formulations designed to manufacture the photoactive TiO2 nanoparticles. To strive for sustainable processing and pave the way for the use of liquid-phase film processing technologies, the inherent limited water dispersibility of TiO2 nanoparticles must be overcome. In this study, we show that cellulose nanocrystals, produced via an environmentally benign one-pot hydrolysis process, enable the preparation of stable TiO2 water dispersions. The remarkable stability of these dispersions, evidenced by their outstanding ξ-potential values of −34 mV, facilitates the fabrication of macroporous TiO2 photoactive films throughout spray coating. Employed as photoanodes in a photoelectrochemical cell, our TiO2 photoanodes are compared with conventional TiO2 electrodes obtained from commercial pastes under water splitting conditions. Interestingly, our photoanodes reveal a remarkable three-fold enhancement of the photocurrent performance (132 vs. 46 μA cm−2) and a four-fold increase in the on–off response rate (4 vs. 1 s). These findings underscore the valuable role of cellulose nanocrystals as a green processing asset for achieving TiO2 water dispersions. Moreover, they serve as sacrificial adjuvants for preparing highly macroporous and functional film photoelectrodes, representing a significant step forward in the pursuit of sustainable and efficient materials processing., Sustainability spotlight : Photoelectrochemical processes are essential for many clean energy production methods. For such purpose, the involved electrodes are typically fabricated by means of polluting additives and toxic solvents. Designing efficient electrodes in a sustainable way is of fundamental interest. There is thus a need for non-toxic and green aqueous dispersants, for which nanocellulose shows promising prospects of sustainability and cost-effectiveness. Here we use cellulose nanocrystals in combination with TiO2 nanoparticles, not only to valorise renewable raw materials, but also to conform functional photoanodes in a ground-breaking way. These electrodes are able to undergo photoelectrochemical water splitting, performing more efficiently than a commercial TiO2 benchmark due to the role of nanocellulose, which goes beyond a mere dispersing agent. Our methodology addresses important aspects of responsible consumption and production (UN SDG 12), affordable and clean energy (UN SGD 7), and climate action (UN SDG 13)., Financial support from Spanish MCIN/AEI/10.13039/501100011033 and “ERDF A way of making Europe” under project grants PID2022-139671OB-I00 and PID2020-120439-RA-I00, as well as by the Gobierno de Aragón (DGA) under projects T03_23R and E47_23R (Grupos de Investigación Reconocidos) is acknowledged. V. C. is thankful for his PhD contract funded by DGA (Ref. CUS/581/2020)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación Set de datos (Dataset)

Supplementary information for Towards sustainable TiO2 photoelectrodes based on cellulose nanocrystals as a processing adjuvant [Dataset]

  • Martínez-Barón, Carlos
  • Calvo Peña, Víctor
  • Hernández-Ferrer, Javier
  • Villacampa, Belén
  • Ansón-Casaos, Alejandro
  • González Domínguez, José Miguel
  • Maser, Wolfgang K.
  • Benito, Ana M.
20 figures, 2 tables.-- TEM, size distribution and elemental analysis of CNC: TEM images of the type II CNC are presented in Figure S1 and the distribution of diameters and heights of the CNC are in Figure S2. It can be observed the characteristic shape and size of this type of CNC, with a mean diameter 28 ± 13 nm and a length of 58 ± 15 nm. Type II CNCs were analyzed to determine their composition by elemental analysis and the results are presented in Table S1. The most characteristic result is the relative high mass percentage of sulfur of 3.45%, which is clearly higher than the value in type I CNCs prepared by the same approach. The elemental composition (C, H, N and S) of the CNCs was determined using a LECO 628 elemental analyzer (Velp Scientifica). The elemental analysis was performed in triplicate to ensure reproducibility, and the average values were reported. Commercial TiO2 paste (TiO2-P): Film fabrication: The commercial paste (TiO2-P) was dried in an oven at 120 ºC overnight to remove organic solvents and get a material ready for subsequent solid stated characterization such as XRD and TGA measurements. For the preparation of the photoelectrodes using the commercial paste, an optimized screen-printing procedure was employed following the instructions provided by the supplier. The paste was applied to cover a 1 cm2 surface area of the FTO substrates. Subsequently, the electrode was thermally sintered in an oven with the following temperature profile: 5 minutes at 325 ºC, 5 minutes at 375 ºC, 5 minutes at 450 ºC, and 15 minutes at 500 ºC, under an air atmosphere, according to the instructions from the provider. Prior to the photoelectrochemical (PEC) evaluation, the TiO2 film was activated by treating it at 500 ºC in air for 30 minutes. Preparation of TiO2(NH4OH) and solid material: TiO2(NH4OH) dispersions were prepared by mixing 50 mg of anatase powder, 300 µL of commercial aqueous ammonia (30%) and 19.7 mL of ultrapure water. Then, the resulting mixture was homogenized in an ultrasonic bath for 1 h. Dispersions were freeze-dried to obtain powder materials for further characterization. UV-Vis of the employed materials: Figure S5a shows the transmittance curves of various aqueous dispersions, including freshly prepared TiO2-NPs, TiO2(NH4OH), CNC materials, and the TiO2(NH4OH) material after 24 hours of dispersion preparation. At the selected wavelength of 360 nm, the TiO2- NPs dispersion exhibits the highest transmittance, indicating an unstable system with most of the material settling down. Conversely, the TiO2(NH4OH) material shows lower transmittance values, which moderately increases after 24 hours, evidencing successful dispersion of the TiO2-NPs when ammonia was used. Figure S5b shows the variation of the transmittance for the TiO2(NH4OH), TiO2-CNC and TiO2-CNC(NH4OH) materials with time. The results demonstrate the effective role of ammonia in facilitating the dispersion of TiO2-NPs, although CNC exhibited superior stabilization efficiency. Notably, the combination of ammonia and CNC yields the most stable aqueous dispersions, as evidenced by consistent transmittance values even after 24 hours. TEM of the TiO2(NH4OH) material: TEM images in Figure S6 reveal the presence of TiO2 aggregates, typically smaller than 100 nm. It seems that the addition of NH4OH during the preparation of the TiO2-NPs dispersion effectively disrupt the formation of large aggregates. Thermogravimetric analysis of CNC: All thermogravimetric analysis (TGA) of powder materials were carried out under air atmosphere in a Libra F1 (Netzsch) thermobalance using a ramp of 10 ºC/min. Figure S7 confirms that CNC have been completely eliminated, as there is no residual mass after the experiment. Thermogravimetric analysis of the TiO2-CNC material: As the CNC residue is 0% at 800 ºC and approximately of 5% at 450 ºC, it can be deduced that CNC have been completely removed from the TiO2 matrix during the sintering step (450 ºC, 2 hours). The TiO2-CNC material reveals a 50% of residual mass, which confirms that all CNC were removed at a 1:1 TiO2 : CNC ratio (Figure S8). Differences in surface morphology between films prepared from commercial TiO2- P and TiO2-CNC(NH4OH): Figure S9 shows the results from the profilometry measurements of TiO2-P and TiO2- CNC(NH4OH) films. Both films displayed remarkable differences in surface characteristics. While TiO2-P film shows a smooth surface, the film obtained from the TiO2-CNC(NH4OH) dispersion exhibits a significant higher roughness. This disparity is clearly a consequence of the respective fabrication methodologies. In the case of the TiO2-P, screen printing was employed, allowing the particles to accommodate under the gentle pressure of the printing blade, resulting in a roughness of 110 nm (Figure S9a). By contrast, the spray coating process immobilized the TiO2-NPs upon contact with the hot substrate, leading to rapid droplet evaporation and the formation of a film with a pronounced roughness of 1300 nm (Figure S9b). Effect of CNC in the surface morphology. Comparison between films prepared from commercial TiO2-P and TiO2(NH4OH): To gain more insight into the effect of film processing, namely screen printing and spray coating, a comparison between TiO2 photoanodes of the same thickness (~3.5 µm) prepared by both techniques is herein shown. The screen-printed TiO2 photoanode was prepared with the GreatCell® paste, whereas the spray-coated TiO2 photoanode was fabricated from the TiO2(NH4OH) dispersions in order to discard the CNC effect upon sintering, as described in the main article. In terms of surface morphology, it is of great interest the study of such property according to the followed fabrication procedure. As commented before, the screen-printed films display low Rq values (Figure S10a) whereas the TiO2(NH4OH) ones show a higher roughness (Figure S10b). These differences directly arise from the film fabrication method followed. Furthermore, the addition of CNC clearly influences the morphology of the film, with the bare TiO2(NH4OH) film showing lower roughness (900 nm, Figure S10b) compared to the TiO2-CNC(NH4OH) one (1300 nm, Figure S9b). Gas physisorption of the TiO2 materials (N2 isotherms): To further explore the effect of the CNC on the macroporous structure of the TiO2-CNC(NH4OH) material used as photoanode, physisorption measurements were conducted on both bare TiO2-NPs and TiO2-CNC(NH4OH) powder materials after sintering. N2 adsorption−desorption at -196 °C (Quantachrome Autosorb-6B Instrument) was measured after sample degassing (250 °C, 4 h) to characterize the porous texture and the equivalent Brunauer−Emmett−Teller (BET) specific surface area (SBET). Figure S11 shows the N2 isotherms of the employed materials. Both materials exhibit type II isotherms according to the IUPAC classification, typical of non-porous solids.The isotherms (Figure S11) reveal an initial increase at low relative pressure values. When it comes to the intermediate region of the isotherms, it is important to note that the TiO2 CNC hybrid has a slightly increased adsorption due to the removal of the biopolymer during the thermal treatment. This probably refers to an enlarged separation between the solid TiO2 particles. A narrow hysteresis loop appears at very high relative pressures, around p/p0 = 0.9, which is commonly ascribed to the capillary condensation taking place within the interstitial pores between TiO2 particles. The BET specific surface area of the TiO2-CNC(NH4OH) powder material is marginally higher (42 m2/g) to the observed for the bare TiO2 nanoparticles (35 m2 /g), evidencingnot too much influence of the CNC in the final internal porosity. Pore size distribution (DFT and BJH methods): Pore size distribution has been calculated for both samples from their N2 adsorption isotherms using the density functional theory (DFT) (Figure S12) and the Barrett-JoynerHalenda (BJH) method (Figure S13), which uses the Kelvin model of pore filling. X-Ray diffraction: X-ray diffraction results of the employed materials, namely CNC (type-II), TiO2-NPs (anatase), TiO2-CNC, and the commercial TiO2 paste (GreatCell®) are shown in Figure S14. The diffractogram of CNC (type-II) is in agreement with literature. The synthesized TiO2-NPs exhibits the characteristic profile of anatase NPs, evidencing a comparable crystal phase composition and crystallite size to the commercial TiO2 paste. The average crystallite size of the employed TiO2-NPs is 25 nm,3 whereas the commercial TiO2 paste is composed of particles distributed in two sizes: 20 and 300 nm. Notably, the XRD analysis of the prepared TiO2-CNC(NH4OH) hybrid shows a combined pattern from TiO2 and CNC, not showing any additional peaks. Thermogravimetric analysis of the commercial TiO2 paste: The concentration of TiO2 in the commercial paste is somewhat higher (62%, Figure S15) to that of the TiO2-CNC. This mass loss is ascribed to the removal of alkylated celluloses from the paste. Scanning electron microscopy of photoanodes from commercial TiO2-P based: Figure S16 shows SEM images of the film obtained from TiO2 commercial paste. The TiO2-P based photoelectrode film displays a smooth surface, both before and after air sintering, despite having a similar content of cellulose derivatives (62 wt.% of TiO2) to our TiO2-CNC(NH4OH) hybrid (50 wt.%) (Figure S8). Photoelectrochemical characterization of the films prepared from TiO2(NH4OH) and commercial TiO2-P: Figure S17 displays the CV profiles of the TiO2(NH4OH) and TiO2-P films, both under dark and illumination. In the absence of light, the photoelectrodes exhibit the characteristic reversible redox behavior of TiO2 electrodes. A cathodic current is observed at more negative potentials, and a nearly symmetric positive current during the backward scan. The voltammograms exhibited an accumulation region at approximately -0.8 V, and a depletion region at higher potentials, -0.4 V. Under illumination conditions, both materials show similar photocurrent values (~ 46 µA·cm2). This observation is further supported by transient photocurrent measurements (Figure S18), which reveal slight differences between the two electrodes (from 32 µA·cm-2 to 43 µA·cm-2), highlighting the significant improvement of the TiO2 electrodes when using CNC and ammonia for their fabrication. 5-hour photocurrent measurements: Aiming to study the stability of the TiO2-CNC(NH4OH) and TiO2-P photoanodes, 5-hour experiments at a constant potential (0 V vs. Ag/AgCl) were performed (Figure S19). A photocurrent decay is observed in both cases, mainly caused by the blocking of the TiO2 active sites due to parasitic redox processes (see references 33, 34 and 35). Nevertheless, the TiO2-CNC(NH4OH) retained a higher PEC performance, even after 5 hours under operation conditions due to its specific morphology that arises from the CNC processing. Electrochemical impedance spectroscopy (EIS): Equivalent circuit: EIS spectra were analyzed according to the model circuit shown in Figure S20. Resistances (RS, Rct and Rsc) and constant phase elements, i.e. non-ideal capacitors with phase angle <90, (CPEdl and CPEsc) are calculated as model fitting parameters to the experimental data.-- Under a Creative Commons license BY-NC 3.0., TEM, size distribution and elemental analysis of CNC. Commercial TiO2 paste (TiO2-P): Film fabrication. Preparation of TiO2(NH4OH) and solid material. DLS and ζ-potential measurements. UV-Vis of the employed materials. TEM of the TiO2(NH4OH) material. Thermogravimetric analysis of CNC. Thermogravimetric analysis of the TiO2-CNC material. Differences in surface morphology between films prepared from commercial TiO2-P and TiO2-CNC(NH4OH). Effect of CNC in the surface morphology. Comparison between films prepared from commercial TiO2-P and TiO2(NH4OH). Physisorption of the TiO2 materials (N2 isotherms). Pore size distribution (DFT and BJH methods). X-Ray diffraction. Thermogravimetric analysis of the commercial TiO2 paste. SEM of photoanodes from commercial TiO2-P. Photoelectrochemical characterization of films prepared from TiO2(NH4OH) and commercial TiO2-P. 5-hour photocurrent measurements. Electrochemical impedance spectroscopy (EIS). Equivalent circuit. References., Financial support from Spanish MCIN/AEI/10.13039/501100011033 and “ERDF A way of making Europe” under project grants PID2022-139671OB-I00 and PID2020-120439-RA-I00, as well as by the Gobierno de Aragón (DGA) under projects T03_23R and E47_23R (Grupos de Investigación Reconocidos) is acknowledged. V. C. is thankful for his PhD contract funded by DGA (Ref. CUS/581/2020)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nanocellulose: The ultimate green aqueous dispersant for nanomaterials

  • Calvo Peña, Víctor
  • Martínez-Barón, Carlos
  • Fuentes Varela, Laura
  • Maser, Wolfgang K.
  • Benito, Ana M.
  • González Domínguez, José Miguel
5 figures, 1 table., Nanocellulose, a nanoscale derivative from renewable biomass sources, possesses remarkable colloidal properties in water, mechanical strength, and biocompatibility. It emerges as a promising bio-based dispersing agent for various nanomaterials in water. This mini-review explores the interaction between cellulose nanomaterials (nanocrystals or nanofibers) and water, elucidating how this may enable their potential as an eco-friendly dispersing agent. We explore the potential of nanocellulose derived from top-down processes, nanocrystals, and nanofibers for dispersing carbon nanomaterials, semiconducting oxide nanoparticles, and other nanomaterials in water. We also highlight its advantages over traditional methods by not only effectively dispersing those nanomaterials but also potentially eliminating the need for further chemical treatments or supporting stabilizers. This not only preserves the exceptional properties of nanomaterials in aqueous dispersion, but may even lead to the emergence of novel hybrid functionalities. Overall, this mini-review underscores the remarkable versatility of nanocellulose as a green dispersing agent for a variety of nanomaterials, inspiring further research to expand its potential to other nanomaterials and applications., Financial support from Spanish MCIN/AEI/10.13039/501100011033 and “ERDF A way of making Europe” under project grants PID2022-139671OB-I00 and PID2020-120439-RA-I00, as well as from Gobierno de Aragón (DGA) under project T03_23R (Grupos de Investigación Reconocidos). V.C. and C.M.-B. thank the DGA for funding their PhD contracts (Ref. CUS/581/2020 and CUS/621/2023)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Carbon nanomaterials-based inks and electrodes using chitin nanocrystals

  • Calvo Peña, Víctor
  • Martínez-Barón, Carlos
  • Vázquez Conejo, Benjamín
  • Domínguez Alfaro, Antonio
  • Paleo, A. J.
  • Villacampa, Belén
  • Ansón-Casaos, Alejandro
  • Maser, Wolfgang K.
  • Benito, Ana M.
  • González Domínguez, José Miguel
5 figures, 2 tables., Dispersing 1D carbon nanomaterials (CNMs) for film processing traditionally relies on surfactants or organic solvents. These methods, however, raise environmental concerns and can negatively impact the final properties of the CNMs. In this work we demonstrate that chitin nanocrystals (ChNCs) synthesized via acid hydrolysis provide a greener pathway for the development of waterborne CNMs-based inks, including single-walled carbon nanotubes, multiwalled carbon nanotubes, and carbon nanofibers. Various concentrations of ChNCs were mixed with each type of CNM to maximize the CNM concentration within the ink. In-depth characterization of the CNM/ChNC inks preceded their processing into supported conductive films by spray-coating. A subsequent thermal treatment of ChNCs at 450 °C leads to the efficient removal of ChNC and results in a significant enhancement of the electrical conductivity. Moreover, freeing the CNMs network structure contributes to increased electrochemical performance of the treated films, as expressed by improved Faradaic charge transfer efficiencies and kinetics reflected by 1 order of magnitude reduced rate constants, when tested with various redox probes. Our findings highlight the potential of ChNCs as a sustainable processing adjuvant of CNMs, leading to electrically conductive electrodes with suitable electrochemical properties for their use in diverse devices and applications., Financial support from Spanish MCINN/AEI/10.13039/501100011033 and “ERDF A way of making Europe” by the European Union under project grants PID2019-104272RB-C51, PID2020-120439RA-I00, and PID2022-139671OB-I00 as well from Spanish CSIC (PIE iniciación ref 202280I007) and from Gobierno de Aragón (DGA, Grupo Reconocido DGA-T03_23R and E47_23R) are acknowledged. V.C. and C.M.-B. thank the DGA for funding their PhD contracts (ref. CUS/581/2020 and CUS/621/2023). A.J.P. gratefully acknowledges support from the FCT-Foundation for Science and Technology by the 2020–2023 Project UIDB/00264/2020. A.D.A. acknowledges UPV/EHU for funding transferred by the European Union-Next Generation EU by the Margarita Salas fellowship (MARSA N° agreement 22/77)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Green processing of carbon nanofibers via cellulose nanocrystals and its relevance towards sustainable e-textiles

  • González Domínguez, José Miguel
  • Calvo Peña, Víctor
  • Paleo, A. J.
  • Muñoz Tavera, Enrique
  • Krause, Beate
  • Pötschke, Petra
  • Maser, Wolfgang K.
  • Benito, Ana M.
1 figure.-- Abstract of the poster presented at the ChemOnTubes 2024 conference, 7-11 April 2024, Strasbourg (France)., Cellulose nanocrystals (CNCs) are a kind of nanostructured biopolymer with unique properties, such as high resistance and water stability [1,2]. Its synthesis is possible through different top-down methods, chemically or physically breaking down the amorphous parts of cellulose. Among these methods, acid hydrolysis is one-pot and allows selecting the cellulose allomorph by only varying the experimental conditions [2]. On the other hand, carbon nanomaterials, such as carbon nanofibers (CNFs), can be integrated into textiles to produce flexible electronic devices. However, it is necessary to use organic solvents or high concentrations of surfactants in water for their dispersion in a liquid medium. CNCs offer a greener alternative, as they have been proved to efficiently disperse different hydrophobic carbon nanomaterials in water [1]. In this study (Figure 1), CNCs were successfully used to prepare aqueous dispersions of CNFs, for the first time and with concentrations of up to 0.7 g L-1 of CNFs [3]. The dispersions, referred to as inks, were characterized with different techniques. Furthermore, as a proof of concept, these inks were integrated into a cotton fabric by a tailored dip coating, resulting in a fabric with thermoelectric properties and a negative Seebeck coefficient. The endurance was tested by washing the textiles under conditions similar to domestic and industrial automated washing. Overall, the obtained results pave the way towards the development of more sustainable and durable wearable electronic textiles, enabled by green aqueous dispersions of CNFs., Funds have been received from the Recognized Research Group T03_23R funded by Government of Aragon (DGA) and the NANOSHIELD project (PID2020-120439RA-I00) from Spanish MICINN Ministry., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Sustainable fabrication of carbon nanotube electrodes based on chitin nanocrystals: unraveling Faradaic charge transfer phenomena

  • Calvo Peña, Víctor
  • Martínez-Barón, Carlos
  • Vázquez Conejo, Benjamín
  • Domínguez Alfaro, Antonio
  • Paleo, Antonio J.
  • Ansón-Casaos, Alejandro
  • González Domínguez, José Miguel
  • Maser, Wolfgang K.
  • Benito, Ana M.
Work presented at the XXV Meeting of The Portuguese Electrochemical Society (SPE2023), 30th august-1st september 2023, Coimbra (Portugal), The use of carbon nanomaterials is widespread in the scientific community due to their excellent optoelectronic and mechanical properties. In particular, carbon nanotubes (CNTs) are typically employed in electrochemical devices for different purposes, ranging from sensing to energy storage applications [1]. An effective way to transfer CNT properties from the nano- to the microscale level is by preparing CNTs-based films [1 – 3]. Commonly, CNTs are dispersed in organic solvents or water by means of surfactants, which can be detrimental for the final application. Aiming to develop sustainable CNT electrodes, chitin nanocrystals (ChNCs) emerge as a promising adjuvant towards the fabrication of waterborne environmentally-friendly CNTs inks. The present work demonstrates the feasibility of ChNCs to render stable aqueous inks of CNTs. These inks were subsequently employed for the preparation of film electrodes over glass substrates by means of spray coating. Once deposited, thickness and surface morphology of the CNT conductive films were evaluated, unraveling remarkable electrical conductivities ranging from 4.1 to 9.5 (S·cm-1). Furthermore, electrochemical measurements of the CNTs/ChNCs electrodes were carried out in a three-electrode cell. Faradaic transfer properties were evaluated using three different redox probes: ferricyanide, ascorbic acid and hydroquinone. For instance, cyclic voltammograms using the ferricyanide probe revealed enhanced charge transfer phenomena when thermally treating both CNTs/ChNCs electrodes in inert atmosphere. This fact has been supported by the standard electrochemical rate constant (k0), which decreased one order of magnitude in both cases after the thermal treatment, having a k0 of 4.1·10-5 for SWCNTs and 3.6·10-4 (cm·s-1) for MWCNTs. These values are in the range of other electrode materials [3, 4], revealing the potential of the herein shown approach., Spanish MICINN/AEI (PID2019-104272RB-C51/AEI/10.13039/501100011033, PID2020-120439RA-I00), Spanish CSIC (PIE iniciación, ref. 202280I007), Gobierno de Aragón (DGA- T03_23R and CUS/581/2020)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación Set de datos (Dataset)

Supporting information for Carbon nanomaterials-based inks and electrodes using chitin nanocrystals [Dataset]

  • Calvo Peña, Víctor
  • Martínez-Barón, Carlos
  • Vázquez Conejo, Benjamín
  • Domínguez Alfaro, Antonio
  • Paleo, A. J.
  • Villacampa, Belén
  • Ansón-Casaos, Alejandro
  • Maser, Wolfgang K.
  • Benito, Ana M.
  • González Domínguez, José Miguel
Under a Creative Commons BY 4.0 license., Additional experimental details, including the surface conditioning of CNMs and the characterization of CNMs and ChNCs along with their combinations, further information about the different CNM/ChNC inks behavior and their subsequent films, and calculations regarding the CNM concentration as well as the electrical conductivity and the standard electrochemical constant, 1. Surface conditioning of CNMs and characterization...........................................S3 2. Calculation of the CNMs concentration post centrifugation ..............................S6 3. Dynamic light scattering results of fresh and redispersed ChNCs.........................S7 4. Morphological characterization of ChNCs................................................................S8 5. Sheet resistance results of the SWCNT/ChNC films..........................................S10 6. Characterization of the CNM/ChNC dispersions...............................................S11 7. Purity index of SWCNT/ChNC dispersions ........................................................S13 8. Homocoagulation analysis of SWCNT/ChNC and MWCNT/ChNC dispersions..S15 9. Sheet resistance results of the CNM/ChNC films..............................................S16 10. SEM images of the CNM/ChNC films ................................................................S17 11. Calculation of the CNM/ChNC films electrical conductivity..............................S18 12. XPS measurements of the CNM/ChNC films..........................................................S19 13. Contact angle measurements of the CNM/ChNC films ....................................S22 14. Calculation of the standard electrochemical rate constant..............................S23 15. References ........................................................................................................S25, Financial support from Spanish MCINN/AEI/10.13039/501100011033 and “ERDF A way of making Europe” by the European Union under project grants PID2019-104272RB-C51, PID2020-120439RA-I00, and PID2022-139671OB-I00 as well from Spanish CSIC (PIE iniciación ref 202280I007) and from Gobierno de Aragón (DGA, Grupo Reconocido DGA-T03_23R and E47_23R) are acknowledged. V.C. and C.M.-B. thank the DGA for funding their PhD contracts (ref. CUS/581/2020 and CUS/621/2023). A.J.P. gratefully acknowledges support from the FCT-Foundation for Science and Technology by the 2020–2023 Project UIDB/00264/2020. A.D.A. acknowledges UPV/EHU for funding transferred by the European Union-Next Generation EU by the Margarita Salas fellowship (MARSA N° agreement 22/77)., Peer reviewed
e_Buah Biblioteca Digital Universidad de Alcalá
Publicación Artículo científico (JournalArticle)

Effect of nanocellulose polymorphism on electrochemical analytical performance in hybrid nanocomposites with non-oxidized single-walled carbon nanotubes

  • Dortez Herranz, Silvia|||0000-0002-1999-5605
  • Sierra Gómez, Tania|||0000-0003-3019-2026
  • Álvarez Sánchez, Miguel A.
  • González Domínguez, José L.
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • Crevillen, Agustín G.
  • Escarpa Miguel, Jesús Alberto|||0000-0002-7302-0948
10 p., Two cellulose nanocrystals/single-walled carbon nanotube (CNC/SW) hybrids, using two cellulose polymorphs, were evaluated as electrochemical transducers: CNC type I (CNC-I/SW) and CNC type II (CNC-II/SW). They were synthesized and fully characterized, and their analytical performance as electrochemical sensors was carefully studied. In comparison with SWCNT-based and screen-printed carbon electrodes, CNC/SW sensors showed superior electroanalytical performance in terms of sensitivity and selectivity, not only in the detection of small metabolites (uric acid, dopamine, and tyrosine) but also in the detection of complex glycoproteins (alpha-1-acid glycoprotein (AGP)). More importantly, CNC-II/SW exhibited 20 times higher sensitivity than CNC-I/SW for AGP determination, yielding a LOD of 7 mg L?1.These results demonstrate the critical role played by nanocellulose polymorphism in the electrochemical performance of CNC/SW hybrid materials, opening new directions in the electrochemical sensing of these complex molecules. In general, these high-active-surface hybrids smartly exploited the preserved non-oxidized SW conductivity with the high aqueous dispersibility of the CNC, avoiding the use of organic solvents or the incorporation of toxic surfactants during their processing, making the CNC/SW hybrids promising nanomaterials for electrochemical detection following greener approaches., Comunidad de Madrid; Ministerio de Economía y Competitividad de España; CRUE-CSIC; Gobierno de Aragon, Comunidad de Madrid, Ministerio de Economía y Competitividad, Ministerio de Ciencia e Innovación, Agencia Estatal de Investigación, Gobierno de Aragón
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Metal-free nanostructured-carbon inks for a sustainable fabrication of zinc/air batteries: from ORR activity to a simple prototype

  • Santos, Florencio
  • Lorca, Sebastián
  • González-Martínez, Juan F.
  • Urbina Yeregui, Antonio
  • Álvarez-Sánchez, Miguel A.
  • González-Domínguez, José M.
  • García-Bordejé, Enrique
  • Ansón-Casaos, Alejandro
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • Fernández Romero, Antonio J.
Zinc/air batteries are convenient energy storage devices for both small and massive applications. While future perspectives indicate the need for low-cost components and sustainable fabrication processes, the battery performance is in part controlled by the kinetics of the oxygen reduction reaction (ORR), which typically involves transition metals as catalysts. In this context, we prepare a series of metal-free water-based carbon inks, which are tested for their catalytic performance, once deposited on a gas-diffusion substrate, in the air cathode of a simple battery prototype. The inks contain a variety of well-defined carbon nanomaterials and additives, exhibiting different physicochemical properties that critically influence the interaction with the gas diffusion hydrophobic substrate. The intrinsic ORR catalytic activity of the ink material is also analyzed on a glassy carbon electrode by the rotating ring-disc electrode (RRDE) method and specific capacitance measurements. The discharge capacity on our zinc/air battery prototype correlates well with the intrinsic catalytic activity in the RRDE. However, only the activity in the RRDE does not actually assure the performance on the commercial cathode of the prototype, since other chemical compatibility issues play a role. Thus, we highlight the importance of catalyst testing, not only on the RRDE but also under realistic device conditions., Financial support from Spanish MICINN under projects PID2019-104272RB-C51-, C55-AEI/10.13039/501100011033, PID2020-120439-RA-I00, Diputación General de Aragón under project T03_20R (Grupo Reconocido) and Fundación Séneca (Región de Murcia, Spain; Ref: 20985/PI/18). The authors also appreciate the financial support provided by the MICINN and the European Union “NextGenerationEU/PRTR” through the project TED2021-130334B-I00