Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

Biblos-e Archivo. Repositorio Institucional de la UAM
Publicación Tesis doctoral (DoctoralThesis)

Corrosion protection of aluminum using integrated self-healing systems

  • Aruchamy, Udhaya Kumar
Tesis Doctoral inédita cotutelada por la Alexander Dubcek University of Trencin y la Universidad Autónoma de Madrid, Faculta de Ciencias, Departamento de Química Inorgánica. Fecha de Lectura: 17-09-2025, El objetivo de esta tesis ha sido desarrollar un sistema de recubrimiento multicapa basado en un recubrimiento de poliorganosilazano (OPSZ)/(3–glicidiloxipropil)trimetoxisilano (GPTMS) combinado con un recubrimiento de conversión de cerio para mejorar la protección contra la corrosión de la aleación AA2024. Las principales conclusiones de la tesis se resumen a continuación. En primer lugar, se realizó un estudio detallado sobre la reactividad de ambos precursores OPSZ y GPTMS, y como los parámetros de síntesis afectaban al entrecruzamiento de la red y, de esta forma a las propiedades anticorrosivas del recubrimiento. Fue necesario seleccionar un disolvente adecuado para conseguir soles de OPSZ/GPTMS estables. Se observó como el acetato de n–butilo (NBTA) era compatible químicamente con el poliorganosilazano utilizado en esta tesis (OPSZ) y permitía estabilizar dicha molécula. Además, la adición de fluoruro de tetra–n–butilamonio (TBAF) a la solución OPSZ/NBTA promovía las reacciones de acoplamiento de hidrógeno (dehydrocoupling) entre los grupos Si–H y N–H del poliorganosilazano y la formación de nuevos enlaces Si–N–Si. Por otro lado, se observó que la incorporación de GPTMS no producía la fragmentación de la molécula de OPSZ, y que era necesario calentar la mezcla a 80 °C para incrementar el grado de reticulación entre GPTMS y OPSZ. Sin embargo, se observó que la humedad relativa afectaba a las reacciones de hidrólisis de los grupos Si–H, N–H y Si–NH–Si (OPSZ) y los grupos Si–O–R (GPTMS), y a su posterior condensación y formación de enlaces Si–O–Si con la correspondiente liberación de NH3 como subproducto. Por lo tanto, la hidrólisis y la condensación promovidas por la humedad relativa generaba cambios estructurales en la red de OPSZ/GPTMS debido a una reactividad no controlada de las reacciones, lo que a su vez afectaba a la reproducibilidad de los recubrimientos de OPSZ/GPTMS. A pesar de estas limitaciones, se prepararon soles de OPSZ/GPTMS y se depositaron sobre la aleación AA2024 mediante el proceso de inmersión–extracción. Se midió la resistencia a la corrosión mediante impedancia compleja, y los resultados mostraron valores de impedancia (109 Ω.cm²) a baja frecuencia superiores a los de la aleación desnuda en NaCl al 3,5 % en peso. Sin embargo, dichos valores de impedancia caían bruscamente con el tiempo de inmersión y la reproducibilidad de las medidas no era buena. Por lo tanto, la tercera fase de esta tesis se centró en mejorar la reticulación de estos recubrimientosC_40%RH a través de la apertura del anillo epoxi de la molécula de GPTMS. Se estudió como la adición de un catalizador, 1–metilimidazol (MI), a la mezcla inicial OPSZ/GPTMS(80ºC) aumentaba el número de enlaces Si–O–Si debido a la apertura parcial del anillo epoxi y a una mayor condensación inorgánica, lo que da como resultado una red más reticulada. En este caso, los nuevos recubrimientos catalizados con MI mostraban una reducción en el espesor debido a una mayor densificación de la red de polímero y además tenían alta hidrofobicidad (98°). Los resultados de EIS (espectroscopia de impedancia electroquímica) mostraban que los recubrimientos obtenidos con los soles con MI, curados a 40% HR y luego tratados térmicamente a 120°C tienen un módulo de impedancia alto después de 168 horas de inmersión en NaCl al 3,5 % en peso. Por lo tanto, las propiedades de protección contra la corrosión de los recubrimientos C_40%RH mejoraron significativamente al aumentar el grado de reticulación de la red OPSZ/ GPTMS. Las pruebas de adherencia revelaron que los recubrimientos obtenidos con los soles con MI tenían buena adhesión al sustrato AA2024–T3, al no observarse ninguna falla de delaminación entre la interfaz recubrimiento/sustrato, This thesis has been funded for the European Union’s Horizon 2020 research and innovation programme under grant agreement No. 739566 for providing funding for this research. I also acknowledge the support from projects MICINN under projects PID2020–115419GB–C21– C22/AEI/10.13039/ 501100011033 and part of the dissemination activities of the MICINN project TED2021–131258B–I00
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Tesis doctoral (DoctoralThesis)

Modelización termodinámica de la estructura y conductividad iónica de vidrios de fosfato y oxinitruros

  • López-Grande, Alberto
[ES] En los últimos años, los vidrios de fosfato han adquirido una creciente relevancia debido a su potencial como electrolitos en baterías de estado sólido. Estas baterías representan una prometedora alternativa a las tradicionales, gracias a su alta densidad de energía, mayor seguridad y estabilidad frente a altas temperaturas. Los vidrios de fosfato presentan propiedades iónicas y estructurales únicas que los convierten en una opción atractiva como electrolitos en baterías de estado sólido. Es importante mencionar también las capas delgadas (amorfas) de oxinitruros de litio y fósforo, conocidas como LiPON, que contribuyen a mejorar la conductividad iónica y la durabilidad química del material. Estas capas ya se emplean comercialmente en microbacterias de estado sólido. Por consiguiente, la modelización de la estructura y las propiedades fisicoquímicas de estos vidrios y oxinitruros se presenta como un área de gran interés para la investigación en baterías de estado sólido. Su estudio puede tener un impacto significativo en el desarrollo de materiales más eficientes y seguros para aplicaciones de almacenamiento de energía. En el contexto de esta Tesis doctoral, se plantea una hipótesis fundamental: es factible predecir la estructura de distintos vidrios y otros sólidos amorfos mediante la modelización termodinámica de la interacción de los óxidos reaccionantes que conforman el sistema vítreo. Esta modalización permitiría, a su vez, prever la conductividad iónica de dichos materiales, abriendo nuevas perspectivas para el avance en este campo. A lo largo de la Tesis se presentan los resultados de la modelización de la estructura y las propiedades fisicoquímicas de los vidrios de fosfato y oxinitruros utilizando las leyes fundamentales de la química y la termodinámica, así como la validación de dicha modelización mediante la comparación de los resultados obtenidos con medidas experimentales. Partiendo del punto anterior, se presenta también la predicción de la conductividad iónica de estos materiales y la comparación de dicha predicción con los resultados obtenidos a partir de medidas experimentales, [EN] In recent years, phosphate glasses have gained increasing relevance due to their potential as electrolytes in solid-state batteries. These batteries ofer a promising alternative to traditional ones, thanks to their high energy density, improved safety, and stability at high temperatures. Phosphate glasses exhibit unique ionic and structural properties that make them an attractive option as electrolytes in solid-state batteries. It is also worth mentioning the thin layers (amorphous) of lithium and phosphorus oxynitrides, known as LiPON, which enhance the ionic conductivity and chemical durability of the material. These layers are already commercially used in micro solid-state batteries. Therefore, modeling the structure and physicochemical properties of these phosphate glasses and oxynitrides presents an area of great interest for solid-state battery research. Such investigations can have a signifcant impact on the development of more efcient and safer materials for energy storage applications. In the context of this doctoral thesis, a fundamental hypothesis is proposed: it is feasible to predict the structure of diferent glasses and other amorphous solids through thermodynamic modeling of the interaction of the reacting oxides that form the glass system. This modeling would, in turn, enable the prediction of the ionic conductivity of these materials, opening new perspectives for advancements in this feld. Throughout the thesis, the results of modeling the structure and physicochemical properties of phosphate-based glasses and oxynitrides using the fundamental laws of chemistry and thermodynamics are presented. The validation of this modeling is carried out by comparing the obtained results with experimental measurements. Building on the previous point, the prediction of the ionic conductivity of these materials is also presented, and this prediction is compared with the results obtained from experimental measurements, Este trabajo ha sido financiado por los siguientes proyectos: Proyecto FunGlass, programa de investigación e innovación Horizon 2020 de la Unión Europea, acuerdo de subvención N.º 739566. Proyecto de generación de conocimiento PID2020-115419-GB-C21, Ministerio de Ciencia e Innovación, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Tesis doctoral (DoctoralThesis)

Sistema integrado de recubrimientos anticorrosivos con efecto auto-curado para aleaciones ligeras combinando el proceso de anodizado y el proceso Sol-Gel: procesamiento y caracterización

  • Merino, Emilia
Tesis Doctoral inédita leída en la Universidad Autónoma de Madrid, Facultad de Ciencias, Departamento de Químia Física Aplicada. Fecha de Lectura: 12-03-2024 Esta Tesis tiene embargado el acceso al texto completo hasta el 12-09-2025, El trabajo de investigación de la presente tesis doctoral se ha llevado a cabo en el marco del proyecto Europeo “Centre for funcional and Surface-functionalized glasses” (FunGlass) No739566 y es parte de las actividades de diseminación del proyecto MICINN TED2021-131258B-I00, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Tesis doctoral (DoctoralThesis)

Multifunctional coatings on glass by sol-gel method for different applications, Recubrimientos multifuncionales preparados por sol-gel sobre sustratos de vidrio para diferentes aplicaciones

  • Haritha, Ajitha Haridasan
Tesis Doctoral inédita cotutelada por la Trenčianska Univerzita Alexandra Dubčeka V Trenčíne (Eslovaquia) y por la Universidad Autónoma de Madrid, Facultad de Ciencias, Departamento de Química Inorgánica. Fecha de Lectura: 16-12-2024, [EN] Thin film technology plays an important role in our day-to-day life. This technology involves the application of thin layers of materials, often at the micron or nanometer scale, onto different substrates. Thin films can alter the properties of these substrates and impart certain functionality. In recent years, coatings with multifunctionality through surface functionalization concepts have attracted significant interest in the glass industry. This is mainly due to their numerous applications, such as in solar cells, smart windows, and photocatalysis. In this research, the sol-gel method is used to obtain coatings with different functionalities such as antireflective, hydrophobic, photocatalytic, antibacterial and electrochromic properties. The sol-gel method is preferred over other deposition techniques such as pulsed laser deposition, chemical vapor deposition, and magnetron sputtering since it yields high-quality coatings at a low-cost and with a simple deposition procedure. In the scope of this research, coatings consisting of silica-titania (SiO2-TiO2) and triethoxy(octyl)silane (OTES)-modified SiO2 sol were deposited onto glass substrates to achieve antireflective and hydrophobic functionalities. On the other hand, zinc oxide (ZnO) and silver nanoparticle (AgNP) doped ZnO thin film were used to obtain photocatalytic and antibacterial properties. In addition, the ZnO thin film deposited on fluorine-doped tin oxide (FTO) glass was utilized as a counter electrode in a tungsten trioxide (WO3)-based electrochromic device. Thus, this research work is divided into three main parts based on the functionalities of the coating. In the first part of the research work, a double-layer coating was designed and fabricated on glass surfaces by sol-gel method using a silica-titania (SiO2-TiO2) thin film as the bottom layer and an inorganic-organic octyl triethoxy silane (OTES) modified SiO2 upper layer. The refractive index of the SiO2-TiO2 and OTES-modified SiO2 layers were 1.79 and 1.45, and their thicknesses were approximately 76.8 nm and 94.2 nm, respectively. A uniform and crack-free SiO2/SiO2-TiO2 coating was obtained with a percentage transmission of 99.1 in the visible region of the solar spectrum at 550 nm wavelength and with good hydrophobicity (contact angle of 104º). The developed multilayer coating can function as an antireflective and self-cleaning coating as cover glass on top of solar cells. In the second part, ZnO thin films on glass substrates were prepared via sol-gel by dip-coating technique to use them as photocatalyst. The effect of annealing temperature (300-550 ºC) of the ZnO thin film in the degradation of organic methyl orange (MO) dye using a solar simulator was evaluated. The photocatalytic properties of the ZnO films were also analyzed as a function of the optical, morphology, and compositional properties. XRD and Raman analysis confirmed the hexagonal wurtzite structure of ZnO. On the other hand, homogeneous, crack-free, and spherical-like features of ZnO films were observed from the SEM micrograph. The percentage transmission of all ZnO films annealed at different temperatures was > 80% in the 400–800 nm wavelength range. The best photocatalytic activity under solar radiation was shown by ZnO thin film annealed at 450 ºC. ZnO films developed can accelerate the degradation of MO, one of the main water pollutants found in the effluent from the textile and paper sectors. Furthermore, silver nanoparticles (AgNPs) were also incorporated into the ZnO film to evaluate their effect on the photocatalytic performance and their potential use as antibacterial coating. As-prepared AgNPs have been incorporated into ZnO sols to produce AgNP-doped ZnO sol (Ag-ZnO) and Ag-ZnO coatings were developed using simple sol-gel dip coating. The photocatalytic activity was studied through the degradation of methyl orange in aqueous solution under solar simulator. A significant improvement of the photocatalytic activity was observed for the Ag-ZnO coatings compared to coatings without Ag. The coating using 3 mol% AgNP in ZnO showed the best photocatalytic activity. This effect can be attributed to the role of silver in enhancing the efficiency of superoxide anion radical and hydroxyl radical generation. Antibacterial application of ZnO and AgNP doped ZnO thin films using Escherichia coli (E.coli) as a model for gram-negative bacteria, and Staphylococcus aureus (S. aureus) as gram-positive bacteria was also studied. AgNP-doped ZnO exhibited superior antibacterial activity relative to undoped ZnO thin films. Finally, in the third part, the fabrication of electrochromic devices using sol-gel-derived metal oxide thin films was used. Electrochromic devices (ECD) have attracted significant interest in the past two years for their potential uses in a wide variety of applications such as optical displays, anti-glare automobile rear-view mirrors, and smart windows. However, challenges such as simple and cost-effective electrochromic material preparation, insufficient coloration, lengthy switching times, and poor cycling stability still need to be overcome. In the thesis, an electrochromic device is fabricated by combining WO3 thin film as a working electrode and a ZnO thin film as a counter electrode on FTO glass substrates by a simple sol-gel spin coating method. Graphite-coated FTO (C-based ECD) was also used as a counter electrode for a comparative analysis of the ECDs. X-ray diffraction (XRD) studies showed that WO3 and ZnO films were well crystallized in monoclinic and hexagonal wurtzite structures with crystallite sizes of 38.5 and 42.2 nm, respectively. Field emission scanning electron microscopy (FE-SEM) images confirmed the formation of porous and nanorod-like structures for WO3 and ZnO films, respectively. Furthermore, the research results showed that the optical contrast at 600 nm of WO3-ZnO ECD was almost twice that of the WO3-C-based ECD. Cyclic voltammetry and chronoamperometry measurements were also used to study the electrochromic properties of the films., I am grateful to the European Union's Horizon 2020 research and innovation programme (grant agreement No. 739566), as well as projects VEGA 1/0844/21 and VEGA 1/0431/18 of the Grant Agency of Slovak Republic. Additionally, I thank the Journal of the European Ceramic Society (JECS) Trust for funding my mobility projects at CSIC-ICV, Peer reviewed