Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 55
Encontrada(s) 1 página(s)

Biblos-e Archivo. Repositorio Institucional de la UAM
Publicación Tesis doctoral (DoctoralThesis)

Corrosion protection of aluminum using integrated self-healing systems

  • Aruchamy, Udhaya Kumar
Tesis Doctoral inédita cotutelada por la Alexander Dubcek University of Trencin y la Universidad Autónoma de Madrid, Faculta de Ciencias, Departamento de Química Inorgánica. Fecha de Lectura: 17-09-2025, El objetivo de esta tesis ha sido desarrollar un sistema de recubrimiento multicapa basado en un recubrimiento de poliorganosilazano (OPSZ)/(3–glicidiloxipropil)trimetoxisilano (GPTMS) combinado con un recubrimiento de conversión de cerio para mejorar la protección contra la corrosión de la aleación AA2024. Las principales conclusiones de la tesis se resumen a continuación. En primer lugar, se realizó un estudio detallado sobre la reactividad de ambos precursores OPSZ y GPTMS, y como los parámetros de síntesis afectaban al entrecruzamiento de la red y, de esta forma a las propiedades anticorrosivas del recubrimiento. Fue necesario seleccionar un disolvente adecuado para conseguir soles de OPSZ/GPTMS estables. Se observó como el acetato de n–butilo (NBTA) era compatible químicamente con el poliorganosilazano utilizado en esta tesis (OPSZ) y permitía estabilizar dicha molécula. Además, la adición de fluoruro de tetra–n–butilamonio (TBAF) a la solución OPSZ/NBTA promovía las reacciones de acoplamiento de hidrógeno (dehydrocoupling) entre los grupos Si–H y N–H del poliorganosilazano y la formación de nuevos enlaces Si–N–Si. Por otro lado, se observó que la incorporación de GPTMS no producía la fragmentación de la molécula de OPSZ, y que era necesario calentar la mezcla a 80 °C para incrementar el grado de reticulación entre GPTMS y OPSZ. Sin embargo, se observó que la humedad relativa afectaba a las reacciones de hidrólisis de los grupos Si–H, N–H y Si–NH–Si (OPSZ) y los grupos Si–O–R (GPTMS), y a su posterior condensación y formación de enlaces Si–O–Si con la correspondiente liberación de NH3 como subproducto. Por lo tanto, la hidrólisis y la condensación promovidas por la humedad relativa generaba cambios estructurales en la red de OPSZ/GPTMS debido a una reactividad no controlada de las reacciones, lo que a su vez afectaba a la reproducibilidad de los recubrimientos de OPSZ/GPTMS. A pesar de estas limitaciones, se prepararon soles de OPSZ/GPTMS y se depositaron sobre la aleación AA2024 mediante el proceso de inmersión–extracción. Se midió la resistencia a la corrosión mediante impedancia compleja, y los resultados mostraron valores de impedancia (109 Ω.cm²) a baja frecuencia superiores a los de la aleación desnuda en NaCl al 3,5 % en peso. Sin embargo, dichos valores de impedancia caían bruscamente con el tiempo de inmersión y la reproducibilidad de las medidas no era buena. Por lo tanto, la tercera fase de esta tesis se centró en mejorar la reticulación de estos recubrimientosC_40%RH a través de la apertura del anillo epoxi de la molécula de GPTMS. Se estudió como la adición de un catalizador, 1–metilimidazol (MI), a la mezcla inicial OPSZ/GPTMS(80ºC) aumentaba el número de enlaces Si–O–Si debido a la apertura parcial del anillo epoxi y a una mayor condensación inorgánica, lo que da como resultado una red más reticulada. En este caso, los nuevos recubrimientos catalizados con MI mostraban una reducción en el espesor debido a una mayor densificación de la red de polímero y además tenían alta hidrofobicidad (98°). Los resultados de EIS (espectroscopia de impedancia electroquímica) mostraban que los recubrimientos obtenidos con los soles con MI, curados a 40% HR y luego tratados térmicamente a 120°C tienen un módulo de impedancia alto después de 168 horas de inmersión en NaCl al 3,5 % en peso. Por lo tanto, las propiedades de protección contra la corrosión de los recubrimientos C_40%RH mejoraron significativamente al aumentar el grado de reticulación de la red OPSZ/ GPTMS. Las pruebas de adherencia revelaron que los recubrimientos obtenidos con los soles con MI tenían buena adhesión al sustrato AA2024–T3, al no observarse ninguna falla de delaminación entre la interfaz recubrimiento/sustrato, This thesis has been funded for the European Union’s Horizon 2020 research and innovation programme under grant agreement No. 739566 for providing funding for this research. I also acknowledge the support from projects MICINN under projects PID2020–115419GB–C21– C22/AEI/10.13039/ 501100011033 and part of the dissemination activities of the MICINN project TED2021–131258B–I00
Addi. Archivo Digital para la Docencia y la Investigación
Publicación Artículo científico (JournalArticle)

Novel Sol-Gel Route to Prepare Eu3+-Doped 80SiO2-20NaGdF4 Oxyfluoride Glass-Ceramic for Photonic Device Applications

  • Cruz, María Eugenia
  • Ngoc Lam Tran, Thi
  • Chiasera, Alessandro
  • Durán, Alicia
  • Fernández Rodríguez, Joaquín Manuel
  • Balda de la Cruz, Rolindes
  • Castro, Yolanda
Oxyfluoride glass-ceramics (OxGCs) with the molar composition 80SiO2-20(1.5Eu3+: NaGdF4) were prepared with sol-gel following the “pre-crystallised nanoparticles route” with promising optical results. The preparation of 1.5 mol % Eu3+-doped NaGdF4 nanoparticles, named 1.5Eu3+: NaGdF4, was optimised and characterised using XRD, FTIR and HRTEM. The structural characterisation of 80SiO2-20(1.5Eu3+: NaGdF4) OxGCs prepared from these nanoparticles’ suspension was performed by XRD and FTIR revealing the presence of hexagonal and orthorhombic NaGdF4 crystalline phases. The optical properties of both nanoparticles’ phases and the related OxGCs were studied by measuring the emission and excitation spectra together with the lifetimes of the 5D0 state. The emission spectra obtained by exciting the Eu3+-O2− charge transfer band showed similar features in both cases corresponding the higher emission intensity to the 5D0→7F2 transition that indicates a non-centrosymmetric site for Eu3+ ions. Moreover, time-resolved fluorescence line-narrowed emission spectra were performed at a low temperature in OxGCs to obtain information about the site symmetry of Eu3+ in this matrix. The results show that this processing method is promising for preparing transparent OxGCs coatings for photonic applications., This project received funding from the European Union’s Horizon 2020 research and innovation program under grant agreement no. 739566. The authors acknowledge financial support from MICINN under projects PID2020-115419GB-C21-C22/AEI/10.13039/501100011033 and University of the Basque Country (Project GIU21/006).
Addi. Archivo Digital para la Docencia y la Investigación
Publicación Artículo científico (JournalArticle)

Spark plasma sintering and optical properties of Tm3+ and Tm3+ /Yb3+ doped NaLaF4 transparent glass-ceramics

  • Sedano Rodríguez, María de las Mercedes
  • Babu, S.
  • Balda de la Cruz, Rolindes
  • Fernández Rodríguez, Joaquín Manuel
  • Durán, Alicia
  • Pascual, María Jesús
Tm3+ doped oxyfluoride glass-ceramics (GCs) containing NaLaF4 nanocrystals (NCs) have been obtained by spark plasma sintering (SPS). First, the precursor glasses were melted and then milled and sieved to a suitable particle size. Glass powder pellets were sintered by spark plasma sintering under vacuum conditions. The SPS processing parameters (temperature, pressure, and holding time) were optimized to obtain transparent glass-ceramics. The times of SPS processing are considerably shorter compared with those for the preparation of these GCs by conventional thermal treatment. All glass-ceramics contain nanocrystals of the β- NaLaF4 phase with an average crystal size of 20 nm, but the more highly doped samples (2Tm3+ and 0.5Tm3+/2Yb3+) show evidence of the presence of another phase corresponding with α-NaLaF4. The luminescence properties of the near infrared (NIR) emissions of Tm3+ for different concentrations reveal the presence of concentration quenching of the 3H4 and 3F4 levels. The analysis of the decay from the 3H4 level with increasing concentration is consistent with a dipole-dipole quenching process assisted by energy migration, whereas the self-quenching of the 3F4→3H6 emission can be attributed to fast diffusion. Energy transfer between Yb3+ and Tm3+ ions is confirmed by the NIR and upconverted (UC) emissions after Yb3+ excitation at 975 nm. No UC emission is observed under 791 nm excitation of Tm3+ ions., Funding from MICINN under project PID2020–115419 GB-C-21/C-22/AEI/10.13039/501100011033 is acknowledged. This paper is part of the dissemination activities of project FunGlass. This project has received funding from the European Union´s Horizon 2020 research and innovation program under grant agreement No 739566.
Addi. Archivo Digital para la Docencia y la Investigación
Publicación Artículo científico (JournalArticle)

Er/Yb co-doped LiYF4 transparent oxyfluoride glass-ceramics with up-conversion optical properties

  • Truong, N.M.P.
  • Sedano Rodríguez, María de las Mercedes
  • Durán, Alicia
  • Balda de la Cruz, Rolindes
  • Pascual, María Jesús
  • Klement, R.
Transparent oxyfluoride glass-ceramics doped with rare earth ions (RE3+) are promising materials for photoluminescence up- and down-conversion. In this study, glass compositions within the system 40SiO2–25Al2O3–18Li2O–7LiF–10YF3 (mol.%) doped with ErF3 and codoped with ErF3/YbF3 were prepared by melt-quenching method and subjected to thermal treatment at temperatures above glass transition (Tg + 35 °C) for long dwell times to obtain the corresponding glass-ceramics. The formation of LiYF4 and LiAlSiO4 nanocrystals was confirmed by XRD analysis after thermal treatment at 540 °C for 20 h. The increase in the treatment time up to 80 h resulted in the enhancement of the UC luminescence yield and the decrease of the Red to Green ratio (R/G) emission intensity. Due to the nano-sized crystals, the glass-ceramic products were transparent (%T) in near-infrared (NIR) and visible spectral region with %T remaining approximately 85% and 75%, respectively, after 20 h treatment. However, the visible window transparency reduced, with %T dropping to around 50% after 80 h due to the increase in crystal size and crystalline fraction. The influence of Yb3+ co-doping on the up-conversion (UC) luminescence has been investigated in the glass-ceramics and compared to the parent glasses, confirming that Yb3+ ions were also a key factor for facilitating up-conversion via energy transfer (ET), leading to a greater luminescence yield than for Er3+ single doped glass-ceramics and tuning of R/G intensities., This work was supported by a part of the European Union’s Horizon 2020 research and innovation program [grant number 739566]; the MICINN [grant number PID2020-115419GBC-21/C-22/AEI/10.13039/501100011033]; and the project VEGA 1/0476/22.
Addi. Archivo Digital para la Docencia y la Investigación
Publicación Artículo científico (JournalArticle)

Crystallization Process and Site-Selective Excitation of Nd3+ in LaF3/NaLaF4 Sol–Gel-Synthesized Transparent Glass-Ceramics

  • Cruz, María Eugenia
  • Li, Jing
  • Gorni, Giulio
  • Durán, Alicia
  • Mather, Glenn C.
  • Balda de la Cruz, Rolindes
  • Fernández Rodríguez, Joaquín Manuel
  • Castro, Yolanda
In this study, transparent oxyfluoride glass-ceramics (GCs) with NaLaF4 nanocrystals (NCs) were prepared by the sol–gel method for the first time. Three different molar ratios of La(CH3COO)3/Na(CH3COO) were used to obtain the GCs, which were sintered at 450, 550 and 650 °C for 1 min. X-ray diffraction (XRD) was employed to follow the evolution of the xerogel during the heat treatments and to study crystal growth for the three temperatures. In all cases, the LaF3 crystalline phase was present, but crystallization of NaLaF4 was only promoted at 650 °C. Thermogravimetric and thermodifferential analysis (TGA-DTA) and Fourier transform infrared spectroscopy (FTIR) were used to analyze the crystallization process. High-resolution transmission electron microscopy (HRTEM) was employed to confirm NaLaF4 crystallization and determine the size distribution. The incorporation of Nd3+ ion into NaLaF4 and LaF3 nanocrystals was confirmed by site-selective emission and excitation spectra. The Nd3+ emission intensities in both phases depend not only on the NaLaF4/LaF3 ratio but also on their emission efficiencies., The authors acknowledge financial support from MINECO under projects MAT2017-87035-C2-1-P/-2-P (AEI/FEDER, UE), and Basque Government PIBA2018-24. This article is a part of the dissemination activities of the project FunGlass, which has received funding from the European Union’s Horizon 2020 research and innovation program under grant agreement No 739566.
Addi. Archivo Digital para la Docencia y la Investigación
Publicación Artículo científico (JournalArticle)

KLaF4:Nd3+ doped transparent glass-ceramics processed by spark plasma sintering

  • Babu, S.
  • Balda de la Cruz, Rolindes
  • Fernández Rodríguez, Joaquín Manuel
  • Sedano Rodríguez, María de las Mercedes
  • Gorni, Giulio
  • Cabral, Aluisio Alves
  • Galusek, Dušan
  • Durán, Alicia
  • Pascual, María Jesús
[EN] Transparent oxyfluoride glass-ceramics (GCs) containing KLaF4 nanocrystals (NCs) doped with Nd3+ were prepared by Spark Plasma Sintering (SPS). Glass powder pellets were sintered under a vacuum atmosphere, optimizing the processing parameters such as particle size, pressure, temperature, and holding time to obtain full densification. Transparency decreased when decreasing the particle size due to higher carbon contamination from the die. The alpha-KLaF4 crystalline phase was identified by X-ray diffraction (XRD) and its average crystal size was 10-20 nm. High-resolution transmission electron microscopy (HR-TEM) confirmed the presence of KLaF4 nanocrystals with incorporated Nd3+ ions. Low-temperature site-selective emission and excitation spectra of Nd3+ ions confirmed that alpha-KLaF(4 )was the predominant polymorph, although a minor presence of beta- KLaF4 was also demonstrated., This work was supported by MINECO under Projects MAT2017-87035-C2-1-P/-2-P (AEI/FEDER, UE) , PID2020-115419GB-C-21/C-22 and Basque Country Government PIBA2018-24. AAC also thanks the scholarships of the Federal Agency for the Support and Improvement of Higher Education (CAPES) , contract #99999.002598/2015-09. This paper is part of the dissemination activities of project FunGlass. This project has received funding from the European Unions Horizon 2020 research and innovation program under grant agreement No 739566.
Addi. Archivo Digital para la Docencia y la Investigación
Publicación Artículo científico (JournalArticle)

Non-Linear Optical Properties of Er3+–Yb3+-Doped NaGdF4 Nanostructured Glass–Ceramics

  • Velázquez, José J.
  • Gorni, Giulio
  • Balda de la Cruz, Rolindes
  • Fernández Rodríguez, Joaquín Manuel
  • Pascual, Laura
  • Durán, Alicia
  • Pascual, María Jesús
Transparent oxyfluoride glass–ceramics containing NaGdF4 nanocrystals were prepared by melt-quenching and doped with Er3+ (0.5 mol%) and different amounts of Yb3+ (0–2 mol%). The selected dopant concentration the crystallization thermal treatments were chosen to obtain the most efficient visible up-conversion emissions, together with near infrared emissions. The crystal size increased with dopant content and treatment time. NaGdF4 NCs with a size ranging 9–30 nm were obtained after heat treatments at Tg + 20–80 °C as confirmed by X-ray diffraction and high-resolution transmission electron microscopy. Energy dispersive X-ray analysis shows the incorporation of rare earth ions into the NaGdF4 nanocrystals. Near-infrared emission spectra, together with the up-conversion emissions were measured. The optical characterization of the glass–ceramics clearly shows that Er3+ and Yb3+ ions are incorporated in the crystalline phase. Moreover, visible up-conversion emissions could be tuned by controlling the nanocrystals size through appropriated heat treatment, making possible a correlation between structural and optical properties., This research was funded by Spanish National projects MAT2017-87035-C2-1-P/2-P (AEI/FEDER, UE), Basque Country University PPG17/07 and GIU17/014 and Basque Government PIBA2018-24. This study is part of the dissemination activities of project FunGlass. This project has received funding from the European Union’s Horizon 2020 research and innovation program under grant agreement No 739566. This study was also created in the frame of the project Centre for Functional and Surface Functionalized Glass (CEGLASS), ITMS code is 313011R453, operational program Research and innovation, co-funded from European Regional Development Fund.
Addi. Archivo Digital para la Docencia y la Investigación
Publicación Artículo científico (JournalArticle)

A New Sol-Gel Route Towards Nd3+-doped SiO2-LaF3 Glass-Ceramics for Photonic Applications

  • Cruz, María Eugenia
  • Durán, Alicia
  • Balda de la Cruz, Rolindes
  • Fernández Rodríguez, Joaquín Manuel
  • Mather, Glenn C.
  • Castro, Yolanda
Glass-ceramic materials with composition 0.9Nd(3+)-80SiO(2)-20LaF(3) were successfully obtained and further heat-treated at 450 degrees C for 6 h. Stable and homogeneous LaF3 nanoparticle suspensions with and without Nd3+ were first prepared by a chemical route, incorporating polyvinylpyrrolidone (PVP) as dispersant. The suspensions were then concentrated and characterised by XRD, HRTEM and zeta potential, confirming that LaF3 crystallises as the only phase, with particle size around 16 nm. The suspensions were incorporated in a silica sol to obtain a 0.9Nd(3+)-20LaF(3)-80SiO(2) particulate sol, xerogel and glass-ceramic. HRTEM confirmed the homogeneous incorporation of the doped nanocrystals into the SiO2 matrix without modification of the nanoparticle structure. Rietveld refinement was used to determine the crystallinity and quantity of LaF3 nanoparticles present in the glass-ceramic after treatment of the particulate sol at 450 degrees C for 6 h. Luminescence measurements of near infrared Nd3+ ion emissions in the lanthanum fluoride nanoparticles and SiO2-LaF3 glass-ceramic showed well-structured emission spectra with lifetimes similar to those of theoretical Nd+3 in LaF3 crystals, The authors acknowledge the financial support from MINECO under projects MAT2017-87035-C2-1-P/-2-P (AEI/FEDER, UE), Basque Country University GIU17/014 and Basque Government PIBA2018-24. This article is a part of the dissemination activities of the project FunGlass, which has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement no. 739566. The authors also acknowledge the support of the Transmission Electron Microscope (TEM) service of the Institute of Catalysis and Petrochemistry (CSIC)
Addi. Archivo Digital para la Docencia y la Investigación
Publicación Artículo científico (JournalArticle)

Optically active nano-glass-ceramic coatings of Nd3+ doped-80SiO2-20LaF3 prepared by the pre-crystallized nanoparticles sol-gel route

  • Cruz, María Eugenia
  • Fernández Rodríguez, Joaquín Manuel
  • Durán, Alicia
  • Balda de la Cruz, Rolindes
  • Castro, Yolanda
Transparent oxyfluoride glass-ceramic (OxGCs) coatings with composition 1.2Nd3+ 80SiO2- 20LaF3 were prepared following a sol-gel route labelled “pre-crystallized nanoparticles route”. OxGCs are transparent materials composed by one or more fluoride nanocrystals in a glass matrix. OxGCs have been prepared by sol-gel with encouraging results in powders and bulk glass-ceramics but not in coatings. In the present work, aqueous suspensions of LaF3 nanoparticles doped with Nd3+ were prepared by chemical route and then incorporated into a silica sol to obtain 1.2Nd3+ doped-80SiO2-20LaF3 particulate sols. Nd3+-LaF3 suspensions are characterized by XRD, HRTEM, and XRF revealing the presence of LaF3 as the unique crystalline phase. Then, 1.2Nd3+ -80SiO2-20LaF3 coatings were prepared by dip-coating and characterized by XRD, FTIR, and Ellipsometry. Photoluminescence measurements were performed for LaF3 nanoparticles and OxGCs coatings, confirming the presence of Nd3+ in the nanocrystals and showing well-structured crystalline-like emission spectra with lifetimes of 520 and 440 µs respectively., The authors acknowledge financial support from MICINN under projects PID2020-115419GB-C21- C22/AEI / 10.13039/501100011033 and from the Basque Country University under project GIU21/006. This article is a part of dissemination activities of the project FunGlass, which has received funding from the European Union´s Horizon 2020 research and innovation program under grant agreement No 739566.
Biblos-e Archivo. Repositorio Institucional de la UAM
Publicación Artículo científico (JournalArticle)

Transparent sol-gel oxyfluoride glass-ceramics with high crystalline fraction and study of re incorporation

  • Gorni, Giulio
  • Velázquez, José J.
  • Mosa Ruiz, Jadra
  • Mather, Glenn C.
  • Serrano, Aida
  • Vila, María
  • Castro, Germán Rafael
  • Bravo Roldán, David
  • Balda, Rolindes
  • Fernández, Joaquín
  • Durán, Alicia
  • Castro, Yolanda
Transparent oxyfluoride glass-ceramic films and self-supported layers with composition 80SiO2-20LaF3 doped with Er3+ have been successfully synthesized by sol-gel process for the first time. Crack-free films and self-supported layer with a maximum thickness up to 1.4 µm were obtained after heat treatment at the low temperature of 550 ◦C for 1 min, resulting in a LaF3 crystal fraction of 18 wt%, as confirmed by quantitative Rietveld refinement. This is the highest value reported up to now for transparent oxyfluoride glass-ceramics prepared by sol-gel. This work provides a new synthesis strategy and opens the way to a wide range of potential applications of oxyfluoride glass-ceramics. The characterization by a wide range of techniques revealed the homogeneous precipitation of LaF3 nanocrystals into the glass matrix. X-ray absorption spectroscopy and electron paramagnetic resonance confirmed that the Er3+ ions are preferentially embedded in the low phonon-energy LaF3 nanocrystals. Moreover, photoluminescence (PL) measurements confirmed the incorporation of dopants in the LaF3 nanocrystals. The effective concentration of rare-earth ions in the LaF3 nanocrystals is also estimated by X-ray absorption spectroscopy, This research was funded by Spanish National projects MAT2017-87035-C2-1-P/2-P (AEI/FEDER, UE), MAT2016-75362-C3-1-R, and Basque Country University PPG17/07 and GIU17/014. We acknowledge The European Synchrotron Radiation Facility (ESRF), MINECO, and CSIC for the provision of measurements using the BM25-SpLine beamline. This paper is a part of dissemination activities of project FunGlass. This project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 739566. A.S. acknowledges the financial support from the Comunidad de Madrid for an “Atracción de Talento Investigador” contract (No. 2017-t2/IND5395)
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Transparent SiO2-GdF3 sol–gel nano-glass ceramics for optical applications

  • Velázquez, J. J.
  • Mosa Ruiz, Jadra
  • Gorni, Giulio
  • Balda, Rolindes
  • Fernández, Joaquín
  • Pascual, Laura
  • Durán, Alicia
  • Castro Martín, Yolanda
Transparent oxyfluoride nano-glass-ceramics (GCs) containing GdF3 nanocrystals undoped and doped with 0.5 Eu3+ (mol%) were obtained by a novel sol–gel method after sintering at temperatures such low as 550 °C. X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM) show the precipitation of GdF3 nanocrystals with size between 7 and 10 nm, depending on the crystalline phase (hexagonal or orthorhombic) and the heating time. Fourier transform infrared spectroscopy (FTIR) analysis allows following the system evolution during the heat treatment showing the decomposition of trifluoroacetic acid (TFA), used as fluorine precursor, together with the formation of fluoride lattice bonding. Energy dispersive X-ray (EDX) analysis confirms the incorporation of the RE ions in the fluoride nanocrystals in the GCs. The ions incorporation on the GdF3 crystals is also supported by optical characterisation. Photoluminescence measurements result in a well resolved structure together with a narrowing of the Eu3+ emission and excitation spectra in the GCs compared to the xerogel. Moreover, the asymmetry ratio between the electric dipole transition (5D0→7F2) to the magnetic dipole transition (5D0→7F1) is reduced in GCs, indicating that Eu3+ ions are incorporated in the GdF3 crystalline phases. Moreover, Gd3+→Eu3+ energy transfer with enhancement of the energy transfer efficiency was observed in the GCs, further supported by fluorescence decay curves., This work was supported by MINECO under Projects N° MAT2013-48246-C2-1-P, MAT2013-48246-C2-2-P and Basque Country University PPG17/07 and GIU17/014. The authors thank the access to the Spanish Beamline (SpLine) at the ESRF facilities in Grenoble. J.J. Velázquez also acknowledges MINECO under Grant FPDI-2013-16895. This paper is also a part of dissemination activities of project FunGlass. This project has received funding from the European Union´s Horizon 2020 research and innovation programme under grant agreement No 739566., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Tunable upconversion emission in NaLuF4-glass-ceramic fibers doped with Er3+ and Yb3+

  • Gorni, Giulio
  • Velázquez, J. J.
  • Kochanowicz, Marcin
  • Dorosz, Dominik
  • Balda, Rolindes
  • Fernández, Joaquín
  • Durán, Alicia
  • Pascual, M. Jesús
[EN] Novel glass-ceramic optical fibers containing NaLuF nanocrystals doped with 0.5ErF and 2YbF (mol%) have been prepared by the rod-in-tube method and controlled crystallization. NaLuF nanocrystals with a size around 20 nm are obtained after heat treatment at 600 °C. Intense upconverted green and red emissions due to (H, S) → I and F → I transitions, respectively, together with a blue emission due to H → I transition have been observed under excitation at 980 nm. The intensity of the green and red upconversion bands shows a nearly linear dependence on the excitation power which can be explained by saturation effects in the intermediate energy states and proves that a sensitized energy transfer upconversion process is responsible for the population of the emitting levels of Er ions. The upconversion emission color changes from yellow to green by increasing the excitation power density which allows to manipulate the color output of the Er emission in the glass-ceramic fibers. The tunable emission color is easily detected with the naked eye. This interesting characteristic makes these glass-ceramic fibers promising materials for photonic applications., This work was supported by MINECO under the project MAT2017-87035-C2-1-P/-2-P (AEI/FEDER, UE) and Basque Country University PPG17/07 and GIU17/014, and Basque Government PIBA2018-24. Funding from MPNS Cost Action MP1401 is also acknowledged. This paper is a part of dissemination activities of project FunGlass. This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement no. 739566.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Glass-Ceramics Processed by Spark Plasma Sintering (SPS) for Optical Applications

  • Singarapu, Babu
  • Galusek, Dušan
  • Durán, Alicia
  • Pascual, M. Jesús
© 2020 by the authors., This paper presents a review on the preparation of glass-ceramics (GCs) and, in particular, transparent GCs by the advanced processing technique of spark plasma sintering (SPS). SPS is an important approach to obtain from simple to complex nanostructured transparent GCs, full densification in a short time, and highly homogeneous materials for optical applications. The influence of the different processing parameters, such as temperature, pressure, sintering dwell time on the shrinkage rate, and final densification and transparency, are discussed and how this affects the glass material properties. Normally, transparent glass-ceramics are obtained by conventional melt-quenching, followed by thermal treatment. Additionally, the GC scan is produced by sintering and crystallization from glass powders. Hot pressing techniques (HP) in which the source of heating is high-frequency induction can be also applied to enhance this process. In the case of transparent ceramics and glass-ceramics, spark plasma sintering is a promising processing tool. It is possible to enhance the material properties in terms of its compactness, porosities, crystallization, keeping the size of the crystals in the nanometric scale. Moreover, the introduction of a high concentration of active gain media into the host matrix provides functional glass-ceramics systems with enhanced luminescence intensity through reducing non-radiative transitions like multi phonon relaxation (MPR) and cross relaxations (CR), thus providing longer lifetimes. More effort is needed to better understand the sintering mechanisms by SPS in transparent GC systems and optimize their final optical performance., Funding from the project MAT2017-87035-C2-1-P/2-P (AEI/FEDER, UE) is acknowledged. This paper is a part of the dissemination activities of project FunGlass. This project has received funding from the European Union’s Horizon 2020 research and innovation program under grant agreement No. 739566. Funding from the project VEGA 1/0527/18 is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Structure and Raman spectra of binary barium phosphate glasses

  • Hruška, Branislav
  • Dagupati, Rajesh
  • Chromčíková, Mária
  • Nowicka, Aleksandra
  • Michálková, Jaroslava
  • Peterson, Jacob A.
  • Liška, Marek
  • Muñoz, Francisco
[EN] The structure of xBaO·(1 − x) PO (x = 0.30, 0.35, 0.40, 0.45, and 0.50) glasses was studied by Raman spectroscopy and thermodynamic model Shakhmatkin and Vedishcheva (SVTDM). The seven system components (defined as stable crystalline phases of the BaO–PO binary phase diagram) were considered in the SVTDM: BaO, PO, 4BaO·PO (B4P), 3BaO·PO (B3P), 2BaO·PO (B2P), BaO·PO (BP), and BaO·2 PO (BP2). Only the equilibrium molar abundances of BP and BP2 were non-negligible in all studied glass compositions. Therefore, in the next step, multivariate curve analysis (MCR) of the baseline—subtracted, thermally—corrected experimental Raman spectra, was performed for two components (BP2 and BP). MCR resulted in the Raman spectra (loadings) and relative abundances (scores) of each considered component. The MCR method reproduced 98.93% of the spectral data variance. Then, the decomposition of Malfait was used. The perfect fit between the MCR loadings and the partial Raman spectra of BP2 and BP, obtained by Malfait’s decomposition, was found, confirming the validity of thermodynamic model., This paper is created in the frame of the Project FunGlass that has received funding from the European Union’s Horizon 2020 research and innovation program under Grant Agreement No. 739566. This work was supported by The Slovak Grant Agency for Science under Grant No. VEGA 1/0064/18, and the Project Centre for Functional and Surface Functionalized Glass (CEGLASS), ITMS code is 313011R453, operational program Research and innovation, co-funded from European Regional Development Fund.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Hybrid Sol–Gel Silica Coatings Containing Graphene Nanosheets for Improving the Corrosion Protection of AA2024-T3

  • Afsharimani, Nasima
  • Durán, Alicia
  • Galusek, Dušan
  • Castro Martín, Yolanda
© 2020 by the authors., In the present work, nanostructured graphene nanosheets were added to hybrid silica sols and deposited on aluminium alloy A2024-T3 to study the effect on the corrosion behaviour. Sols were prepared using tetraethyl-orthosilicate (TEOS), 3-glycidoxypropyl-trimethoxysilane (GPTMS) and a colloidal silica suspension (LUDOX) as silica precursors with adding chemically modified graphene nanosheets (GN-chem). The graphene nanosheets were modified through a straightforward and simple hydrothermal approach and then, dispersed into a silica sol (SiO2/GN-chem). ATR-FTIR was used to optimize the silica sol–gel synthesis and to confirm the cross-linking of the silica network. The corrosion behaviour of the SiO2/GN-chem coatings was also analysed by electrochemical measurement (potentiodynamic polarization) in 0.05 M NaCl solution. The results showed that the incorporation of modified graphene nanosheets into hybrid silica sol–gel coatings affected the corrosion properties of the substrates. An improvement in the corrosion resistance was observed likely due to the enhanced barrier property and hydrophobic behaviour obtained by incorporation of GN-chem and colloidal silica nanoparticles., The authors acknowledge financial support from the European Union. This paper is a part of dissemination activities of the project FunGlass. This project has received funding from the European Union´s Horizon 2020 research and innovation program under grant agreement No 739566., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

58S and 68S sol-gel glass-like bioactive coatings for enhancing the implant performance of AZ91D magnesium alloy

  • Omar, S. A.
  • Ballarre, J.
  • Castro, Y.
  • Martínez-Campos, Enrique
  • Schreiner, W.
  • Durán, Alicia
  • Cere, S. M.
Magnesium alloys such as AZ91D, has been presented as potential material for temporary implant material since it has a mechanical performance suitable with bone tissue and also degrades in time. The fast degradation at early times of AZ91D alloy could be retarded applying bioactive sol-gel glass coatings. In this work, two compositions of known bioactive silica-glasses (58S and 68S) were synthetized by sol-gel method and deposited by dip coating to the magnesium substrates. The glasses were produced without using any nitrate precursor, avoiding the presence of remaining residual in the coatings that could be not beneficial to the body. The coatings presented an excellent bioactive response after immersion in Hanks' balanced salt solution (HBSS) at 37 °C, showing apatite related deposits after 72 h immersion detected by scanning electron microscopy, Raman spectroscopy and X-ray photoelectron spectroscopy. Corrosion behaviour has been also analyzed, 58S presented as better protective features after 17 days of immersion. Cell attachment and proliferation tests demonstrate that both 58S and 68S coatings on AZ91D magnesium alloy are suitable as temporary implant materials., Authors would like to acknowledge Dr. Matias Valdes for the help with logistics. This work was supported by CONICET (PUE-073 and PIP 0572), UNMdP Project 15G/509 (Argentina) and Ministerio de Economía y Competitividad (MINECO) MAT2013-42957-R (Spain). This paper is a part of dissemination activities of the project FunGlass. This project has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement No 739566.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Non-linear optical properties of Er3+–Yb3+-doped NaGdF4 nanostructured glass–ceramics

  • Velázquez, J. J.
  • Gorni, Giulio
  • Balda, Rolindes
  • Fernández, Joaquín
  • Pascual, Laura
  • Durán, Alicia
  • Pascual, M. Jesús
This article belongs to the Special Issue Preparation and Application of Nanostructured Glass–Ceramics and Nanocomposites., Transparent oxyfluoride glass–ceramics containing NaGdF4 nanocrystals were prepared by melt-quenching and doped with Er3+ (0.5 mol%) and different amounts of Yb3+ (0–2 mol%). The selected dopant concentration the crystallization thermal treatments were chosen to obtain the most efficient visible up-conversion emissions, together with near infrared emissions. The crystal size increased with dopant content and treatment time. NaGdF4 NCs with a size ranging 9–30 nm were obtained after heat treatments at Tg + 20–80 °C as confirmed by X-ray diffraction and high-resolution transmission electron microscopy. Energy dispersive X-ray analysis shows the incorporation of rare earth ions into the NaGdF4 nanocrystals. Near-infrared emission spectra, together with the up-conversion emissions were measured. The optical characterization of the glass–ceramics clearly shows that Er3+ and Yb3+ ions are incorporated in the crystalline phase. Moreover, visible up-conversion emissions could be tuned by controlling the nanocrystals size through appropriated heat treatment, making possible a correlation between structural and optical properties., This research was funded by Spanish National projects MAT2017-87035-C2-1-P/2-P (AEI/FEDER, UE), Basque Country University PPG17/07 and GIU17/014 and Basque Government PIBA2018-24. This study is part of the dissemination activities of project FunGlass. This project has received funding from the European Union’s Horizon 2020 research and innovation program under grant agreement No 739566. This study was also created in the frame of the project Centre for Functional and Surface Functionalized Glass (CEGLASS), ITMS code is 313011R453, operational program Research and innovation, co-funded from European Regional Development Fund., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A new sol–gel route towards Nd3+-doped SiO2–LaF3 glass-ceramics for photonic applications

  • Cruz, María Eugenia
  • Durán, Alicia
  • Balda, Rolindes
  • Fernández, Joaquín
  • Mather, Glenn C.
  • Castro Martín, Yolanda
Glass-ceramic materials with composition 0.9Nd3+–80SiO2–20LaF3 were successfully obtained and further heat-treated at 450 °C for 6 h. Stable and homogeneous LaF3 nanoparticle suspensions with and without Nd3+ were first prepared by a chemical route, incorporating polyvinylpyrrolidone (PVP) as dispersant. The suspensions were then concentrated and characterised by XRD, HRTEM and zeta potential, confirming that LaF3 crystallises as the only phase, with particle size around 16 nm. The suspensions were incorporated in a silica sol to obtain a 0.9Nd3+–20LaF3–80SiO2 particulate sol, xerogel and glass-ceramic. HRTEM confirmed the homogeneous incorporation of the doped nanocrystals into the SiO2 matrix without modification of the nanoparticle structure. Rietveld refinement was used to determine the crystallinity and quantity of LaF3 nanoparticles present in the glass-ceramic after treatment of the particulate sol at 450 °C for 6 h. Luminescence measurements of near infrared Nd3+ ion emissions in the lanthanum fluoride nanoparticles and SiO2–LaF3 glass-ceramic showed well-structured emission spectra with lifetimes similar to those of theoretical Nd+3 in LaF3 crystals., The authors acknowledge the financial support from MINECO under projects MAT2017-87035-C2-1-P/-2-P (AEI/FEDER, UE), Basque Country University GIU17/014 and Basque Government PIBA2018-24. This article is a part of the dissemination activities of the project FunGlass, which has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement no. 739566. The authors also acknowledge the support of the Transmission Electron Microscope (TEM) service of the Institute of Catalysis and Petrochemistry (CSIC)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nd3+doped- SiO2–KLaF4 oxyfluoride glass-ceramics prepared by sol-gel

  • Cruz, María Eugenia
  • Li, Jing
  • Gorni, Giulio
  • Durán, Alicia
  • Mather, Glenn C.
  • Balda, Rolindes
  • Fernández, Joaquín
  • Castro Martín, Yolanda
Neodymium (Nd3+) doped SiO2–KLaF4 oxyfluoride glass-ceramic (GCs) containing 10 mol% and 20 mol% of KLaF4 nanocrystals (NCs) were prepared for the first time by sol-gel and sintered at 550 °C. Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) were used to analyze the evolution of the xerogel during the heat treatment, high-resolution transmission electron microscopy (HRTEM) was employed to study the formation and distribution of NCs in the silica matrix. The decomposition of trifluoroacetic acid (TFA) and the crystallization of fluoride nanocrystals were also confirmed. The presence of α-KLaF4 and β-KLaF4 crystalline phases with maximum crystal sizes of 24 nm and 17 nm respectively were clearly observed after heat treatment at 550 °C for 1 min. Site-selective emission and excitation spectra confirmed the incorporation of Nd3+ ions in both crystalline phaseswith emission of Nd3+ most predominant in the β-KLaF4 NCs., The authors acknowledge the financial support from MINECO under projects MAT2017-87035-C2-1-P/-2-P (AEI/FEDER, UE), Basque Country University GIU17/014 and Basque Government PIBA2018-24. This article is a part of the dissemination activities of the project FunGlass, which has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement No 739566., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Crystallization process and site-selective excitation of Nd3+ in LaF3/NaLaF4 sol–gel-synthesized transparent glass-ceramics

  • Cruz, María Eugenia
  • Li, Jing
  • Gorni, Giulio
  • Durán, Alicia
  • Mather, Glenn C.
  • Balda, Rolindes
  • Fernández, Joaquín
  • Castro Martín, Yolanda
This article belongs to the Special Issue Glass-Ceramics: Improving Glass Properties through Crystallization., In this study, transparent oxyfluoride glass-ceramics (GCs) with NaLaF4 nanocrystals (NCs) were prepared by the sol–gel method for the first time. Three different molar ratios of La(CH3COO)3/Na(CH3COO) were used to obtain the GCs, which were sintered at 450, 550 and 650 °C for 1 min. X-ray diffraction (XRD) was employed to follow the evolution of the xerogel during the heat treatments and to study crystal growth for the three temperatures. In all cases, the LaF3 crystalline phase was present, but crystallization of NaLaF4 was only promoted at 650 °C. Thermogravimetric and thermodifferential analysis (TGA-DTA) and Fourier transform infrared spectroscopy (FTIR) were used to analyze the crystallization process. High-resolution transmission electron microscopy (HRTEM) was employed to confirm NaLaF4 crystallization and determine the size distribution. The incorporation of Nd3+ ion into NaLaF4 and LaF3 nanocrystals was confirmed by site-selective emission and excitation spectra. The Nd3+ emission intensities in both phases depend not only on the NaLaF4/LaF3 ratio but also on their emission efficiencies., The authors acknowledge financial support from MINECO under projects MAT2017-87035-C2-1-P/-2-P (AEI/FEDER, UE), and Basque Government PIBA2018-24. This article is a part of the dissemination activities of the project FunGlass, which has received funding from the European Union’s Horizon 2020 research and innovation program under grant agreement No 739566., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Structural and optical properties in Tm3+/Tm3+–Yb3+ doped NaLuF4 glass-ceramics

  • Velázquez, J. J.
  • Balda, Rolindes
  • Fernández, Joaquín
  • Gorni, Giulio
  • Sedano, Mercedes
  • Durán, Alicia
  • Galusek, Dušan
  • Pascual, M. Jesús
Transparent NaLuF4 glass-ceramics (GCs) doped with Tm3+ and Tm3+/Yb3+ have been prepared by melting-quenching followed by thermal treatment at temperatures near the glass transition temperature. The crystallization process has been studied using X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM). NaLuF4 nanocrystals (NCs) ranging 9–30 nm in size are the only crystalline phase, the crystal size increasing with the dopant concentration. Energy dispersive X-ray (EDX) measurements confirm the Tm3+ and Yb3+ incorporation in the NCs. Optical characterization included the analysis of up-conversion (UC) as well as the Near-infrared (NIR) luminescence. NIR emission spectra of Tm3+ and Yb3+ in co-doped samples confirmed an efficient energy transfer between both ions. No UC emissions are observed in Tm3+ single-doped glass and GCs. Yb3+ incorporation favors the Tm3+-Tm3+ UC processes resulting in Tm3+ blue, yellowish-red and NIR UC emissions after excitation at 975 nm. Blue UC emission is also observed in the codoped samples after Tm3+ excitation at 791 nm. These effects were more evident for the GCs compared to the base glasses, confirming the RE ions incorporation in the NCs. As a result, these GCs can be used to tune the UC emission from NIR to blue by selective excitation., This work was supported by MINECO under Projects MAT2017-87035-C2-1-P/-2-P (AEI/FEDER, UE), Basque Country Government PIBA2018-24 and Basque Country University GIU17/014. This article is part of the dissemination activities of project FunGlass. This project has received funding from the European Union´s Horizon 2020 research and innovation programme under grant agreement No 739566. This article was also created in the frame of the project Centre for Functional and Surface Functionalized Glass (CEGLASS), ITMS code is 313011R453, operational program Research and innovation, co-funded from European Regional Development Fund. This research work has been supported by the Research Agency of the Ministry of Education, Science, Research and Sport of the Slovak Republic, by the project: Advancement and support of R&D for "Centre for diagnostics and quality testing of materials" in the domains of the RIS3 SK specialization, Acronym: CEDITEK II., ITMS2014+ code 313011W442., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Integrated corrosion-resistant system for AZ31B Mg alloy via plasma electrolytic oxidation (PEO) and sol-gel processes

  • Merino, Emilia
  • Durán, Alicia
  • Castro Martín, Yolanda
[EN] In this work, an integrated system that combines anodizing process with the deposition of a hybrid SiO sol-gel coating was developed with the aim of improving the corrosion resistance of AZ31B Mg alloy. The optimization of the anodizing conditions using an alkaline electrolyte (NaOH) modified with different concentrations of sodium metasilicate pentahydrate was explored together with the preparation and deposition of a SiO sol obtained by hydrolysis and condensation of TEOS (tetraethoxysilane), GPTMS (3-Glycidyloxypropyl) trimethoxysilane), colloidal SiO nanoparticles, and 1-Methylimidazole (MI). The surface morphology, coating thickness, and composition were evaluated. The anodized coatings thickness was between 1.1 and 1.7 μm with composition corresponding to magnesium oxide and low silicon content. The corrosion performance was tested in 3.5% NaCl solution. The results revealed a good corrosion resistance behavior after the anodizing of the Mg alloys. However, the best corrosion resistance was reached when the porous PEO layer was sealed with a hybrid silica sol-gel film. A decrease in the corrosion current density of three orders of magnitude is observed between Mg alloy (1.54E-06 A/cm) and multilayer system (2.80E-8 A/cm). Moreover, the polarization resistance for 8AF+SG samples showed a quite high value (31546.8 Ω cm) compared to Mg alloy (207.3 Ω cm)., This article is a part of the dissemination activities of the project FunGlass, which has received funding from the European Union´s Horizon 2020 research and innovation program under grant agreement number: 739566. The authors would like to thank Dra. Silvia Ceré from INTEMA (Universidad Nacional de Mar del Plata-CONICET) for the electrochemist formal analysis and support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Structure and fluorescence properties of Dy-doped alkaline-earth borophosphate glasses

  • Griebenow, Kristin
  • Muñoz, Francisco
  • Tagiara, Nagia S
  • Klement, Róbert
  • Prnová, Anna
  • Wolfrum, Bruno
  • Kamitsos, Efstratios I.
  • Durán, Alicia
  • Galusek, Dušan
[EN] Dysprosium- doped borophosphate glasses, containing the divalent cations Mg2+, Ca2+, Sr2+, Ba2+, and Zn2+, are prepared by the melt- quenching technique. The struc-ture of the glasses is investigated by Raman, infrared, and nuclear magnetic resonance (NMR) spectroscopies and the fluorescence properties are determined. The Dy3+emission lifetime increases with an increasing ionic field strength and its maximum is observed in the Mg2+ and Zn2+ containing glasses. This result can be explained by the stronger M- O bonding which causes a rearrangement of the borophosphate network and creates a local Dy3+ environment of comparably low symmetry. This is in agree-ment with the Raman spectra and the evolution of the molar volume. The effect of the B/P variation on the emission properties of Dy3+ is investigated in a second series of glasses where the emission lifetime is found to be maximum at 10 mol% B2O3, This paper is a part of the dissemination activities of the project FunGlass. This project has received funding from the European Union´s Horizon 2020 research and innovation program under grant agreement No 739566. This work was also supported by the Slovak Research and Development Agency under contract No. APVV-17-0049 and by grant VEGA 1/0527/18. NST and EIK acknowledge support by the project “National Infrastructure in Nanotechnology, Advanced Materials and Micro-/Nanoelectronics” (MIS 5002772), funded by the Operational Programme “Competitiveness, Entrepreneurship and Innovation” (NSRF 2014-2020) and co-financed by Greece and the European Union (European Regional Development Fund).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of dopant precursors on the optical properties of rare‐earths doped oxyfluoride glass‐ceramics

  • Gorni, Giulio
  • Serrano Rubio, Aída
  • Bravo, David
  • Castro, Germán R.
  • Balda, Rolindes
  • Fernández, Joaquín
  • Durán, Alicia
  • Pascual, M. Jesús
[EN] TThe crystallization of fluoride nanocrystals (NCs) in chemically and mechanically stable aluminosilicate glasses has shown interesting optical properties even for small crystal fractions (10‐15 wt%). When rare‐earth (RE) ions are used as dopants, crys-tal‐like features can be reproduced and an increase in the emission and/or energy transfer processes, with respect to the starting glasses, is observed. A crucial point for these materials is the study of the local surrounding of RE ions and their incorpora-tion in the NCs. In fact, the effective concentration in the NCs can be much higher than the nominal concentration, up to one order of magnitude or even higher. The knowledge of RE ions incorporation in the NCs permits choosing proper doping lev-els to optimize both linear and nonlinear optical properties. In this work, transparent oxyfluoride glass‐ceramics with LaF3 NCs, doped with Nd3+ and Er3+ using oxide and fluoride precursors, were prepared using the melt‐quenching method and con-trolled crystallization. The local surrounding of the RE ions was studied using X‐ray absorption spectroscopy, electron paramagnetic resonance and photoluminiscence. The results show that most RE ions are already in a fluorine‐rich amorphous environ-ment even in the initial glass. The crystallization process provokes the RE ion redis-tribution and incorporation in the fluoride NCs. The different RE precursors, used as oxides or fluorides, have an influence on the incorporation of the RE in the NCs and, as a consequence, on the final optical properties., Comunidad de Madrid, Grant/Award Number: 2017‐t2/IND5395; European Synchrotron Radiation Facility; Ministerio de Ciencia e Innovación, Grant/Award Number: MAT2016‐75362‐C3‐1‐R; Euskal Herriko Unibertsitatea, Grant/Award Number: PPG17/07 and GIU17/014; MINECO, Grant/Award Number: MAT2017‐87035‐C2‐1‐P/‐2‐P; European Union, Grant/Award Number: 739566, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Improving corrosion protection of Mg alloys (AZ31B) using graphene-based hybrid coatings

  • Afsharimani, Nasima
  • Talimian, Ali
  • Merino, Emilia
  • Durán, Alicia
  • Castro Martín, Yolanda
  • Galusek, Dušan
[EN] In the present work, a study was carried out to compare the morphology and electrochemical properties of pure and graphene-modified hybrid silica sol–gel coatings deposited on anodized AZ31B magnesium alloys. The precursor solution was prepared using tetraethoxysilane (TEOS) and 3-glycidoxypropyl-trimethoxysilane (GPTMS), with the addition of chemically modified graphene nanosheets (GN-chem). Homogeneous and adherent coatings were obtained using GPTMS-TEOS (GT) and GPTMS-TEOS-GN-chem (GT/GN-chem) solutions with uniform thickness around 4 µm. Raman, SEM images and EDS analyses confirmed the presence of graphene nanosheets in the coatings. Potentiodynamic polarization results using 0.05 M NaCl electrolyte solution showed that graphene containing silica coatings significantly improve the corrosion resistance of AZ31B alloys. In addition, a significant passive region was observed for GT/GN-chem coatings., European Union’s Horizon2020 Research and Innovation program,Grant/AwardNumber:739566, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Integrated self-healing coating system for outstanding corrosion protection of AA2024

  • Castro Martín, Yolanda
  • Özmen, Eren
  • Durán, Alicia
[EN] This work reports the preparation of an integrated self-healing system that combines the anodization of Al-substrates with the deposition of environmentally friendly coatings prepared by sol-gel for obtaining an active corrosion protection of aluminum alloys AA2024. The system consists on a first step of forming appropriate anodized layers by controlling the potential and anodizing time. The second step is the infiltration of a cerium sol-gel sol and deposition of a Ce-glass like film, followed by a final hybrid silica sol-gel coating, creating an adherent, stable and active corrosion protective system. SEM, electrochemical techniques (potentiodynamic and EIS tests) as well as an accelerated corrosion test are used to analyze the structure of the coatings and to study the corrosion behavior of the different coatings on AA2024. The results of potentiodynamic measurements showed the excellent corrosion properties and EIS measurements confirmed the self-healing behavior by blocking the pitting defects. The outstanding self-healing corrosion protecting behavior provided by this integrated self-healing coating system offers an efficient chromium-free system for substituting chromium CCC and CCA coatings., This work was supported by Spanish MINECO under project MAT2017-87035-C2-1-PP. This paper is also part of dissemination activities of project FunGlass. This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 739566, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

International Journal of Applied Glass Science: Special Issue Editorial

  • Bernardo, Enrico
  • Boccaccini, Aldo R.
  • Durán, Alicia
  • Galusek, Dušan
  • Wondraczek, Lothar
The Centre for Functional and Surface- functionalized glass(FUNGLASS, www.fungl ass.eu) is a glass research institute founded in 2017 as the result of joint efforts of five part-ners from four European countries: the Alexander Dubček University of Trenčín, Slovakia; Friedrich-Alexander University Erlangen- Nuremberg, Germany (FAU); the Spanish National Research Council, Madrid, Spain (CSIC); the University of Padova, Italy (UNIPD); and Friedrich Schiller University Jena, Germany (FSU); with massive fi-nancial support (15 million €) from the EU program Horizon 2020 under the scheme H2020-WIDESPREAD- 01- 2016- 2017-TeamingPhase2, and the complementary support from the government of the Slovak Republic from the European Regional Development Fund in the frame of the Operational Program Research and Innovation (10 million €)., H2020 Spreading Excellence and Widening Participation, Grant/Award Number: 739566
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Chemical approach to the glass structure and properties

  • Vedishcheva, Natalia
  • López-Grande, Alberto
  • Muñoz, Francisco
This paper continues the series of works by the present authors on the modeling of glass structure and properties. Calculations are performed using the concept of the chemical structure based on the rigorous thermodynamic model of associated solutions. The aim of the present contribution is to demonstrate the applicability of the concept to a wider range of systems than that considered before. For this reason, glasses in the systems with different chemical natures determined by the acidity and basicity of the constituent oxides are considered. The glass structure is calculated at the level of the short-range order in the systems BaO‒SiO and MO(MO)‒PO (M = Li, Na, and Zn) and the intermediate-range order in the systems RbO‒BO and CsO‒BO. The structure-property relationship is quantitatively established by the example of the molar volume of BaO‒SiO glasses. All calculations are performed without the use of adjustable parameters and the results obtained are compared with the experimental data available in the literature., Agencia Estatal de Investigación-FEDER,UE,Grant/AwardNumber:PID2020-115419GB-C21; European Union Horizon 2020 research and innovation program, Grant/AwardNumbers:FUNGLASS,739566; Ministry of Science and Higher Education of the Russian Federation as part of the IChSRAS stateassignment, Grant/AwardNumber:AAAA-A19-119022290088-8
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The structure of barium phosphate glasses and its influence on their thermodynamic stability and viscous flow

  • Dagupati, Rajesh
  • Liška, Marek
  • López-Grande, Alberto
  • Muñoz, Francisco
[EN] The Shakhmatkin and Vedishcheva thermodynamic (SVTD) model of associated solutions has been developed in glasses of the system BaO–P2O5, with the aim of deriving their short range structure and predicting the volume properties. The applicability of the model was examined by comparing the structure obtained from thermodynamic modelling and by Nuclear Magnetic Resonance spectroscopy. The evaluation of the molar volume of the investigated glasses was carried out through comparison of the experimental values calculated by two approaches: i) with the glass molar volume obtained through a linear combination of the product of the molar fractions of system components and their respective crystalline volume; and ii) with the molar volumes calculated by a multilinear regression analysis of the experimental molar volume of each composition. Furthermore, the viscosity curves were determined at low and high temperature ranges by beam-bending and rotation methods from which the fragility and activation energy of the viscous flow have been calculated and correlated with the thermodynamic chemical structure of the glasses., This work is a part of the activities of the Funglass project. This project has received funding from the European Union Horizon 2020 research and innovation programme under grant agreement No 739566. Financial support of this work by the grant VEGA 1/0064/18 is gratefully acknowledged.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Rare-earth doped transparent oxyfluoride glass-ceramics: processing is the key [Invited]

  • Cruz, María Eugenia
  • Sedano, Mercedes
  • Castro Martín, Yolanda
  • Pascual, M. Jesús
  • Fernández, Joaquín
  • Balda, Rolindes
  • Durán, Alicia
Oxyfluoride glass-ceramics (OxGCs) are transparent materials composed by an oxide glass matrix with homogeneously distributed fluoride nanocrystals. In particular, OxGCs with RE-doped lanthanide-fluoride nanocrystals are of special interest for photonic applications. More than 600 publications including several review papers were indexed on Scopus related to “glass-ceramics” revealing the importance of the topic. Melt-quenching followed by thermal treatment, is the most used preparation method, which allows materials in bulk and fibre form to be obtained, being also a scalable industrial process. Spark plasma sintering from glass powders is showing promising results. The sol-gel process has appeared as an alternative method to avoid some of the drawbacks of the melting process such as the high temperature. It also permits to process materials with different shapes such as thin films, nano-sized powders or bulk materials at very low temperature. This paper reviews the different aspects involved in the preparation of OxGC materials by melt-quenching, spark plasma sintering and sol-gel and how the processing parameters directly affect the glass-ceramics properties from results of the GlaSS research group from CSIC. A comparison of the thermal, structural and optical properties is discussed along with some perspectives for preparing other advanced materials within this field., The authors acknowledge financial support from MICINN under project PID2020-115419GB-C21/C-22/AEI/10.13039/501100011033. This article is a part of dissemination activities of the project FunGlass, which has received funding from the European Uniońs Horizon 2020 research and innovation program under grant agreement No 739566., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

KLaF4:Nd3+ doped transparent glass-ceramics processed by spark plasma sintering

  • Babu, Singarapu
  • Balda, Rolindes
  • Fernández Lozano, José Francisco
  • Sedano, Mercedes
  • Gorni, Giulio
  • Cabral, A. A.
  • Galusek, Dušan
  • Durán, Alicia
  • Pascual, M. Jesús
Transparent oxyfluoride glass-ceramics (GCs) containing KLaF4 nanocrystals (NCs) doped with Nd3+were prepared by Spark Plasma Sintering (SPS). Glass powder pellets were sintered under a vacuum atmosphere, optimizing the processing parameters such as particle size, pressure, temperature, and holding time to obtain full densification. Transparency decreased when decreasing the particle size due to higher carbon contamination from the die. The α-KLaF4 crystalline phase was identified by X-ray diffraction (XRD) and its average crystal size was 10–20 nm. High-resolution transmission electron microscopy (HR-TEM) confirmed the presence of KLaF4 nanocrystals with incorporated Nd3+ions. Low-temperature site-selective emission and excitation spectra of Nd3+ions confirmed that α- KLaF4 was the predominant polymorph, although a minor presence of β- KLaF4 was also demonstrated., This work was supported by MINECO under Projects MAT2017–87035-C2–1-P/−2-P (AEI/FEDER, UE), PID2020–115419GB-C-21/C-22 and Basque Country Government PIBA2018–24. AAC also thanks the scholarships of the Federal Agency for the Support and Improvement of Higher Education (CAPES), contract #99999.002598/2015–09. This paper is part of the dissemination activities of project FunGlass. This project has received funding from the European Union´s Horizon 2020 research and innovation program under grant agreement No 739566., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Novel sol-gel route to prepare Eu3+-doped 80SiO2-20NaGdF4 oxyfluoride glass-ceramic for photonic device applications

  • Cruz, María Eugenia
  • Lam Tran, Thi Ngoc
  • Chiasera, Alessandro
  • Durán, Alicia
  • Fernández, Joaquín
  • Balda, Rolindes
  • Castro Martín, Yolanda
Oxyfluoride glass-ceramics (OxGCs) with the molar composition 80SiO2-20(1.5Eu3+: NaGdF4) were prepared with sol-gel following the “pre-crystallised nanoparticles route” with promising optical results. The preparation of 1.5 mol % Eu3+-doped NaGdF4 nanoparticles, named 1.5Eu3+: NaGdF4, was optimised and characterised using XRD, FTIR and HRTEM. The structural characterisation of 80SiO2-20(1.5Eu3+: NaGdF4) OxGCs prepared from these nanoparticles’ suspension was performed by XRD and FTIR revealing the presence of hexagonal and orthorhombic NaGdF4 crystalline phases. The optical properties of both nanoparticles’ phases and the related OxGCs were studied by measuring the emission and excitation spectra together with the lifetimes of the 5D0 state. The emission spectra obtained by exciting the Eu3+-O2− charge transfer band showed similar features in both cases corresponding the higher emission intensity to the 5D0→7F2 transition that indicates a non-centrosymmetric site for Eu3+ ions. Moreover, time-resolved fluorescence line-narrowed emission spectra were performed at a low temperature in OxGCs to obtain information about the site symmetry of Eu3+ in this matrix. The results show that this processing method is promising for preparing transparent OxGCs coatings for photonic applications., This project received funding from the European Union’s Horizon 2020 research and innovation program under grant agreement no. 739566. The authors acknowledge financial support from MICINN under projects PID2020-115419GB-C21-C22/AEI/10.13039/501100011033 and University of the Basque Country (Project GIU21/006)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Optically active nano-glass-ceramic coatings of Nd3+ doped-80SiO2-20LaF3 prepared by the pre-crystallized nanoparticles sol-gel route

  • Cruz, María Eugenia
  • Fernández, Joaquín
  • Durán, Alicia
  • Balda, Rolindes
  • Castro Martín, Yolanda
Transparent oxyfluoride glass-ceramic (OxGCs) coatings with composition 1.2Nd3+ 80SiO2- 20LaF3 were prepared following a sol-gel route labelled “pre-crystallized nanoparticles route”. OxGCs are transparent materials composed by one or more fluoride nanocrystals in a glass matrix. OxGCs have been prepared by sol-gel with encouraging results in powders and bulk glass-ceramics but not in coatings. In the present work, aqueous suspensions of LaF3 nanoparticles doped with Nd3+ were prepared by chemical route and then incorporated into a silica sol to obtain 1.2Nd3+ doped-80SiO2-20LaF3 particulate sols. Nd3+-LaF3 suspensions are characterized by XRD, HRTEM, and XRF revealing the presence of LaF3 as the unique crystalline phase. Then, 1.2Nd3+ -80SiO2-20LaF3 coatings were prepared by dip-coating and characterized by XRD, FTIR, and Ellipsometry. Photoluminescence measurements were performed for LaF3 nanoparticles and OxGCs coatings, confirming the presence of Nd3+ in the nanocrystals and showing well-structured crystalline-like emission spectra with lifetimes of 520 and 440 µs respectively., The authors acknowledge financial support from MICINN under projects PID2020-115419GB-C21- C22/AEI / 10.13039/501100011033 and from the Basque Country University under project GIU21/006. This article is a part of dissemination activities of the project FunGlass, which has received funding from the European Union´s Horizon 2020 research and innovation program under grant agreement No 739566., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Spark plasma sintering and optical properties of Tm3+ and Tm3+ /Yb3+ doped NaLaF4 transparent glass-ceramics

  • Sedano, Mercedes
  • Babu, Singarapu
  • Balda, Rolindes
  • Fernández, Joaquín
  • Durán, Alicia
  • Pascual, M. Jesús
Tm3+ doped oxyfluoride glass-ceramics (GCs) containing NaLaF4 nanocrystals (NCs) have been obtained by spark plasma sintering (SPS). First, the precursor glasses were melted and then milled and sieved to a suitable particle size. Glass powder pellets were sintered by spark plasma sintering under vacuum conditions. The SPS processing parameters (temperature, pressure, and holding time) were optimized to obtain transparent glass-ceramics. The times of SPS processing are considerably shorter compared with those for the preparation of these GCs by conventional thermal treatment. All glass-ceramics contain nanocrystals of the β- NaLaF4 phase with an average crystal size of 20 nm, but the more highly doped samples (2Tm3+ and 0.5Tm3+/2Yb3+) show evidence of the presence of another phase corresponding with α-NaLaF4. The luminescence properties of the near infrared (NIR) emissions of Tm3+ for different concentrations reveal the presence of concentration quenching of the 3H4 and 3F4 levels. The analysis of the decay from the 3H4 level with increasing concentration is consistent with a dipole-dipole quenching process assisted by energy migration, whereas the self-quenching of the 3F4→3H6 emission can be attributed to fast diffusion. Energy transfer between Yb3+ and Tm3+ ions is confirmed by the NIR and upconverted (UC) emissions after Yb3+ excitation at 975 nm. No UC emission is observed under 791 nm excitation of Tm3+ ions., Funding from MICINN under project PID2020–115419 GB-C-21/C-22/AEI/10.13039/501100011033 is acknowledged. This paper is part of the dissemination activities of project FunGlass. This project has received funding from the European Union´s Horizon 2020 research and innovation program under grant agreement No 739566., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Er/Yb co-doped LiYF4 transparent oxyfluoride glass-ceramics with up-conversion optical properties

  • Truong, N.M.P.
  • Sedano, Mercedes
  • Durán, Alicia
  • Balda, Rolindes
  • Pascual, M. Jesús
  • Klement, R.
Transparent oxyfluoride glass-ceramics doped with rare earth ions (RE3+) are promising materials for photoluminescence up- and down-conversion. In this study, glass compositions within the system 40SiO2–25Al2O3–18Li2O–7LiF–10YF3 (mol.%) doped with ErF3 and codoped with ErF3/YbF3 were prepared by melt-quenching method and subjected to thermal treatment at temperatures above glass transition (Tg + 35 °C) for long dwell times to obtain the corresponding glass-ceramics. The formation of LiYF4 and LiAlSiO4 nanocrystals was confirmed by XRD analysis after thermal treatment at 540 °C for 20 h. The increase in the treatment time up to 80 h resulted in the enhancement of the UC luminescence yield and the decrease of the Red to Green ratio (R/G) emission intensity. Due to the nano-sized crystals, the glass-ceramic products were transparent (%T) in near-infrared (NIR) and visible spectral region with %T remaining approximately 85% and 75%, respectively, after 20 h treatment. However, the visible window transparency reduced, with %T dropping to around 50% after 80 h due to the increase in crystal size and crystalline fraction. The influence of Yb3+ co-doping on the up-conversion (UC) luminescence has been investigated in the glass-ceramics and compared to the parent glasses, confirming that Yb3+ ions were also a key factor for facilitating up-conversion via energy transfer (ET), leading to a greater luminescence yield than for Er3+ single doped glass-ceramics and tuning of R/G intensities., This work was supported by a part of the European Union’s Horizon 2020 research and innovation program [grant number 739566]; the MICINN [grant number PID2020-115419GBC-21/C-22/AEI/10.13039/501100011033]; and the project VEGA 1/0476/22., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of pre-treatments on adhesion, barrier and mechanical properties of epoxy coatings: A comparison between steel, AA7075 and AA2024

  • Trentin, A.
  • Samiee, R.
  • Pakseresht, A.H.
  • Durán, Alicia
  • Castro Martín, Yolanda
  • Galusek, D.
Supplementary material associated with this article can be found, in the online version, at doi:10.1016/j.apsadv.2023.100479., [EN] In this work five independent pre-treatments – mechanical polishing, alkaline and acid etching, sol-gel primer, and anodizing – were applied on mild steel and aluminum (AA7075 and AA2024) substrates before the deposition of epoxy coatings. The results demonstrate that efficient adhesion can be achieved by simple methodologies and widely available chemicals as an alternative to toxic conversion layers or highly energetic processes. All the treatments provided higher adhesion (up to 75%, 61% and 14% on AA7075, AA2024 and steel, respectively) and better anti-corrosion performance (increase of impedance values at low frequency up to four orders of magnitude) than the polished reference. The anodizing of aluminum alloys yielded good anti-corrosion performance, but slightly lower mechanical properties compared to sol-gel primer and alkaline etching. The hydroxyls density was found to play a major role in strong adhesion prevailing over surface roughness, contact area, oxide thickness and hydrophobicity. Despite the efficient performance of hydrogen bonds from acid and alkaline etching on aluminum, these connections do not yield sufficiently stable bonds that make an impermeable barrier of epoxy coatings on steel. Covalent bonds (Me-O-Si) represent the key to achieve a significant improvement in mechanical and chemical resistance against the ingress of water and polymer chain relaxation. This makes the sol-gel primer a simple, economical, and environmentally alternative towards efficient bonding at a molecular level., Financial support from the European Union´s Horizon 2020 Research and Innovation Programme under grant agreement No 739566, project FunGlass. Additionally, the funding obtained from VEGA 1/0171/21 and VEGA 1/0241/23 is acknowledged. This article is also part of the dissemination activities of MICINN project TED2021-131258B-I00., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Sol–gel derived ZnO thin film as a transparent counter electrode for WO3 based electrochromic devices, Películas delgadas de ZnO por sol-gel para su uso como contra-electrodos transparentes en dispositivos electrocrómicos base WO3

  • Haritha, Ajitha Haridasan
  • Rozman, Martin
  • Durán, Alicia
  • Galusek, Dušan
  • Velázquez, José Joaquín
  • Castro Martín, Yolanda
Please cite this article in press as: A.H. Haritha, et al., Sol–gel derived ZnO thin film as a transparent counter electrode for WO3 based elec trochromic devices, Bol. Soc. Esp. Cerám. Vidr. (2023), https://doi.org/10.1016/j.bsecv.2023.08.002, [EN] Electrochromic devices (ECDs) have the ability to show color even when electrical power is disconnected. However, challenges such as simple and cost-effective electrochromic material preparation, insufficient coloration, slow switching times, and poor cycling stability have yet to be overcome. The paper describes an electrochromic device with WO3 thin film as the electrochromic material for the working electrode and ZnO thin film as a counter electrode fabricated on FTO glass substrates by a simple sol–gel spin coating method. The optical contrast at 600 nm of ZnO counter electrode based ECD (12.4%) is almost double that of graphite counter electrode based ECD (6.5%), showing higher efficiency and better electrochromic response. The properties of ECD devices were also examined using cyclic voltammetry and chronoamperometry measurements with results showing that the devices were stable and the charge required to tint the device (5.6 mA s) is reduced compared to typical graphite-coated counter electrode. These types of devices are promissing candidates to be used as smart windows., [ES] Los dispositivos electrocrómicos (ECD) tienen la capacidad de mostrar color incluso cuando se desconectan de la energía eléctrica. Sin embargo, para su implantación total deben superarse importantes desafíos como la preparación de materiales electrocrómicos simples y rentables, la coloración insuficiente, los tiempos de conmutación que son lentos y la mala estabilidad del ciclo. En este artículo se describe la preparación de un dispositivo electrocrómico basado en una película delgada de WO3 como electrodo de trabajo y una película delgada de ZnO obtenida por sol-gel como contra-electrodo, todo fabricado sobre sustratos de vidrio FTO mediante un método simple de centrifugado. Como resultados destacar que el contraste óptico a 600 nm del ECD basado en el contra-electrodo de ZnO (12,4%) es casi el doble que el del sistema ECD basado en el contra-electro de grafito (6,5%), mostrando una mayor eficiencia y una mejor respuesta electrocrómica. Las propiedades del dispositivo ECD de ZnO también se examinaron mediante voltametría cíclica y cronoamperometría y los resultados mostraron que los dispositivos eran estables y la carga necesaria para teñir el dispositivo (5,6 mAs) se reducía comparado con el dispositivo ECD de grafito. Este tipo de dispositivos son candidatos prometedores para ser utilizados como ventanas inteligentes., This work is a part of the activities of the FunGlass project. This project has received funding from the European Union Horizon 2020 Research and Innovation Program under Grant 739566. This work was also supported by the Grant VEGA 1/0844/21 of the Grant Agency of the Slovak Republic and the authors are grateful to the JECS Trust for funding (contract No. 2022301)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Optical properties of Er3+ doped NaLuF4 transparent glass-ceramics produced by spark plasma sintering

  • Sedano, Mercedes
  • Balda, Rolindes
  • Fernández, Joaquín M.
  • Durán, Alicia
  • Pascual, M. Jesús
[EN] Transparent oxyfluoride glass-ceramics (GCs) containing NaLuF4 nanocrystals doped with Er3+ have been prepared by combination of glass melt-quenching and spark plasma sintering (SPS) of glass powders. The parameters, such as temperature, pressure, particle size and holding times were optimized to obtain the densification of the powdered samples together with the desired transparency. The major advantage of this technique is the shorter times (few minutes) compared with those used for the preparation of these GCs by conventional heat treatments (more than 10 h). SPS presents an important inconvenient, which is the carbon contamination coming from graphite punch, this has been improved using Pt foils. The structural study indicates the presence of nanocrystals corresponding to the crystalline phase α-NaLuF4, with a crystal size between 26 and 31 nm. The optical characterization, which includes near infrared emission and infrared-to-visible up-conversion, confirms the incorporation of Er3+ ions in the nanocrystals. The longer lifetimes of the 4I11/2 and 4I13/2 levels together with the enhancement of the upconverted green and red emissions (as well as the weak blue emission) in the SPS-GCs samples, if compared with the precursor glass, indicates the presence of Er3+ ions in a crystalline environment. Possible energy conversion mechanisms for the green and red emissions based on the temporal behavior of the upconverted luminescence are discussed., Funding from MICINN under projects PID2020-115419GB-C-21/C-22/AEI/10.13039/501100011033 and from the University of the Basque Country GIU21/006 is acknowledged. This paper is part of the dissemination activities of project FunGlass. This project has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement No 739566., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The influence of Al2O3 concentration on the NaYF4 crystallization in oxyfluoride glass–ceramics

  • Dagupati, Rajesh
  • Sedano, Mercedes
  • Klement, Róbert
  • Velázquez, Jose J.
  • Durán, Alicia
  • Muñoz, Francisco
  • Pascual, M. Jesús
  • Galusek, Dušan
[EN] The influence of Al2O3 addition on the precipitation of NaYF4 crystals in oxyfluoride glasses has been investigated through the thermal, structural, and optical characterization of the parent glasses and corresponding glass–ceramics (GCs). The high-resolution transmission electron microscopy analysis of the GC with 5 mol% of Al2O3 shows the presence of phase-separated droplets about 69 nm in size containing several NaYF4 nanocrystals with the diameter of about 10–15 nm. Raman and magic angle spinning nuclear magnetic resonance (MAS-NMR) spectroscopy were used to examine the structural changes attributed to the addition of Al2O3. The 19F MAS-NMR analysis indicated that fluorine atoms are present in different chemical environments (Na–F, Na–Si–F, Na–Al–F, and NaYF4). The increasing amount of Al2O3 reduces the crystallization of NaYF4 phase due to the increased fraction of fluorine bound in Na–Al–F environments. The visible luminescence investigation of the glasses and GCs demonstrated that the intensity of Er3+ ions emission transitions in the GCs was higher than that of the parent glass. This difference was attributed to the presence of Er3+ ions bound in NaYF4 crystalline phase. Further evidence that the Er3+ ions were present in NaYF4 phase was provided by the fact that the excited level Er3+:4S3/2 lifetime was increased in GCs as compared to parent glass., European Union Horizon 2020, Grant/Award Number: 739566; Slovak Grant Agency, Grant/Award Number: VEGA 1/0476/22; RIS3 SK, Grant/Award Number: ITMS2014+:313011W442; European Regional Development Fund, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of humidity in the alteration of unstable glasses

  • Laso, Elena
  • Aparicio, Mario
  • Palomar Sanz, Teresa
[EN] The control of humidity between certain limits is essential to avoid the alteration of historical objects, such as unstable historical glasses. However, the usual limits can be altered due to the presence of volatile organic compounds. This work presents the results of the exposure of soda, potash, and mixed-alkali silicate glasses to neutral and acidic (formic) atmospheres with ∼30%, ∼70%, and ∼100% relative humidity. The hygroscopic capacity of the glass was analyzed by gravimetry, and the surface alteration was evaluated by infrared spectroscopy, optical microscopy, and ion chromatography. In all glasses, the alteration begins with alkali ions’ lixiviation followed by the silica network's hydrolytic attack. The results showed that soda and mixed-alkali silicate glasses exhibit similar behavior, while the potash-lime one experienced the fastest degradation due to its composition. Results also confirmed that high humidity increased the alteration rate causing a higher hygroscopicity and reactivity of glasses. Finally, acidic environments promoted the ion-exchange reaction at high humidity, accelerating the lixiviation of alkaline ions and promoting the diffusion of water into the glass network., European Union Horizon 2020, Grant/Award Number: 739566; Slovak Grant Agency, Grant/Award Number: VEGA 1/0476/22; RIS3 SK, Grant/Award Number: ITMS2014+:313011W442; European Regional Development Fund, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermodynamic calculation of the ionic conductivity of LiPON glasses and solid electrolytes

  • López-Grande, Alberto
  • Mather, Glenn C.
  • Muñoz, Francisco
[EN] LiPON films are one of the most relevant solid electrolytes in Li-ion micro-batteries for low power applications, and the relationships between composition, processing parameters and ionic conductivity have challenged the materials community for the last three decades. Although films have almost exclusively been processed by deposition of Li3PO4 polycrystalline pellets, the amorphous nature of LiPON has permitted the study of compositions with glass-forming ability where the effect of improving the conductivity by nitrogen doping is similar. The aim of this work is to form a general model that allows us to calculate the ionic conductivity of LiPON solid electrolytes for whichever composition. The modelling is based on the application of the fundamental laws of chemical equilibrium to elucidate the different chemical species present for each given system composition. For this purpose, a program in the Matlab software was written, capable of solving simultaneous and competitive chemical equilibria. The method, known as the associated solutions model, was applied to the study of the Li2O–P2O5 system, which is the starting point of the present work. The model assumes that the properties of a given glass or amorphous solid, such as the simulated LiPON films, can be obtained as a function of the weighted contributions from each stable compound in the respective composition diagram. Here, Li2PO2N oxynitride is used as the main phase and, to validate the computed chemical equilibria, nitridation of crystalline Li4P2O7 has been performed by thermal ammonolysis. The combination of the calculations of chemical equilibria together with the structural characterization by XRD and NMR of the products of nitridation from Li4P2O7 allowed us to predict both the formation of Li2PO2N and the existence of a second oxynitride stoichiometric compound with formula LiPO1.5N that would be obtained by nitridation of LiPO3. The solution of the system of equilibria was made possible on development of the Gibbs free energy functions of formation of both oxynitride phases, and the calculation of the activation energy and ionic conductivity in either LiPON thin films or oxynitride glasses, offering comparable values to those found in the literature., The authors thank funding from projects LUMGLASS (PID2020-115419GB-C21/AEI/10.13039/501100011033) and FUNGLASS (European Union Horizon 2020 research and innovation program under grant agreement No 739566). We acknowledge support of the publication fee by the CSIC Open Access Publication Support Initiative through its Unit of Information Resources for Research (URICI)., Electronic supplementary information (ESI) available. See DOI: https://doi.org/10.1039/d3ta00724c, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Al2O3/Y3Al5O12 (YAG)/ZrO2 composites by single-step powder synthesis and spark plasma sintering

  • Vakhshouri, M.
  • Najafzadehkhoee, A.
  • Talimian, A
  • López-Pernía, Cristina
  • Poyato, Rosalía
  • Gallardo-López, Á.
  • Gutiérrez-Mora, F.
  • Prnova, A.
  • Galusek, D.
Alumina-yttrium aluminum garnet (YAG)-zirconia composites are often produced by the melt solidification method. In the present study, we investigated the fabrication of α-AlO/YAlO (YAG)/ZrO composite by Spark Plasma Sintering (SPS) of powders synthesized by Pechini's sol-gel method. The ternary composites with homogenous microstructure and high density were produced by SPS at 1300 °C for 15 min. The addition of ZrO promoted the sintering of composites, resulting in a higher density and, in turn, higher hardness. A change in the indentation fracture behavior as the result of ZrO addition was observed.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

High performance double layer hydrophobic antireflective coatings on glass prepared by sol–gel method

  • Haritha, Ajitha Haridasan
  • Faturíková, K.
  • Durán, Alicia
  • Galusek, Dušan
  • Castro Martín, Yolanda
  • Velázquez, J. J.
A double layer coating was designed and fabricated on glass surfaces by sol-gel method using a silica-titania (SiO2–TiO2) thin film as the bottom layer and an inorganic-organic (triethoxy(octyl)silane (OTES) modified SiO2) upper layer. SiO2 and TiO2 sols were prepared using tetraethyl orthosilicate (TEOS) and titanium isopropoxide (TIP) as precursors and nitric acid (HNO3) as catalyst. The refractive index of the SiO2–TiO2 and OTES modified SiO2 layers were 1.79 and 1.45, and their thicknesses were approximately 76.8 nm and 94.2 nm, respectively. The results show an increase of 7% in transmittance respect to the uncoated glass substrate. At the same time, OTES-modified SiO2 top layer significantly improved the hydrophobicity of the system; the water contact angle of film increased from 56° for system without the OTES modified SiO2 layer to 102° for the system with OTES-modified SiO2 top layer. © 2024 The Authors, This research is a contribution to the FunGlass project, which has been financially supported by the European Union Horizon 2020 Research and Innovation Program under Grant 739566. Additionally, the study received support from the Grant Agency of the Slovak Republic under Grant VEGA 1/0431/18 and VEGA 1/0844/21. The authors acknowledge finantial support from MICINN under projects PID2020-115419GB-C21-C22/AEI/10.13039/501100011033. A. H. Haritha would like to thanks Assoc. Prof. Alfonz Plsko for his constant support and advise. The authors would like to express their gratitude to the JECS Trust for providing funding (contract No. 2022301) ., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Improved corrosion resistance of AZ31B Mg alloy by eco-friendly flash-PEO coatings

  • Merino, Emilia
  • Chandrasekar, A.R.
  • Pakseresht, A.
  • Mohedano, M.
  • Durán, Alicia
  • Castro Martín, Yolanda
The aim of this work was the preparation of an environmentally friendly protective coating on the AZ31B alloy using Flash plasma electrolytic oxidation (F-PEO) process. It was developed with different electrolyte compositions, that determine the morphology and properties of the coatings, this being crucial to understand the anti-corrosion properties. The incorporation of carbonate ions to the electrolyte proved to enhance the electrical response of the F-PEO process, resulting in a more efficient process with an energy reduced consumption of 1.1 kW h m−2μm−1. Surface and cross-sectional morphology analysis of the coatings revealed the presence of isolated pores structure with small pore size (less than 1 µm) that delays the infiltration of aggressive ions towards the substrate. The characterisation by XRD, EDX and Raman spectroscopy showed the presence of amorphous carbonate and phosphate phases in the FPEO-CO layer, that provide a self-restauration effect through a dissolution/reprecipitation mechanism. The lowest value of the corrosion current density was obtained for FPEO-CO coating, 4.60 × 10−7 A·cm−2, together with the highest impedance modulus (f<0.1 Hz), ⁓104 Ω·cm2, two orders of magnitude higher than the AZ31B Mg alloy. Furthermore, the corrosion protection properties of FPEO-CO coating were also analysed through an immersion test in 3.5 wt.% NaCl, confirming the excellent response of the coating for long times up to 336 h (2 weeks). The synergy between a more compact coating and the self-repairing ability of carbonate amorphous species plays a critical role in improving the corrosion resistance properties of the AZ31B Mg alloy, offering an eco-friendly alternative to chromate conversion coatings. © 2024 The Author(s), This article is a part of the dissemination activities of MICINN project TED2021-131258B-I00, and the project FunGlass, which has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement No 739566. M., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Bio-based vanillin alcohol diglycidyl ether (DGEVA)-silica coatings for corrosion protection of AA2024

  • Trentin, A.
  • Merino, Emilia
  • Samiee, R.
  • Parchoviansky, M.
  • Pakseresht, A.H.
  • Durán, Alicia
  • Castro Martín, Yolanda
  • Galusek, Dušan
Background: Currently, 75% of global epoxy polymers are based on bisphenol A (BPA), a substance identified as reprotoxic, posing challenges to the development of eco-friendly epoxy coatings. Methods: Our study reports the synthesis of three novel bio-based anti-corrosion coatings composed of vanillin alcohol diglycidyl ether (DGEVA) and silica nanoparticles, which were added to improve the adhesion to AA2024 substrates. Findings: The coatings present high adhesion (∼7 MPa) and excellent thermal stability (>295 °C), besides good corrosion protection of the hybrid coating (impedance modulus of ∼4 MΩ cm−2 in 3.5 wt% NaCl for > 68 days). The results reveal that proper silica distribution fosters adhesion and extends lifespan via metal oxide-polymer bonds. © 2024 The Author(s), We acknowledge the financial support from the European Union's Horizon 2020 research and innovation programme (grant No 739566) , project FunGlass, VEGA 1/0171/21 and VEGA 1/0242/23 fundings., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Humidity-induced curing and anti-corrosion properties of GPTMS-modified polyorganosilazane functionalized silica coating on AA2024-T3 aluminum alloy

  • Aruchamy, U.K.
  • Merino, Emilia
  • Durán, Alicia
  • Pálková, H.
  • Galusek, Dušan
  • Castro Martín, Yolanda
Relative humidity (RH) is one of the key parameters that significantly affect the curing kinetics and final properties of polysilazane-based coatings. Thus, the paper discusses the effect of relative humidity during the curing process and the anti-corrosion properties of (3-glycidyloxypropyl) trimethoxysilane (GPTMS)-modified polyorganosilazane (OPSZ) functionalized silica coatings on AA2024-T3. Modified polyorganosilazane sol was prepared and then deposited on AA2024-T3 substrates varying the curing conditions. After the deposition, the coated aluminum substrates were exposed to different RH levels; 15%, 40% and 80%, and then cured at 120 °C for 2 h. Transparent and crack-free GPTMS-modified polyorganosilazane coatings with a thickness of around 15–17 μm were obtained. The exposure to the relative humidity increased the crosslinking and hydrolysis-condensation reactions of the OPSZ and GPTMS molecules, showing more Si-O-Si bonds. The incorporation of GPTMS affected the crosslinking structure, enhancing the corrosion protection properties of the coating. GPTMS-modified polyorganosilazane coatings cured at 40%RH had the best anti-corrosive properties after immersion in 3.5 wt% NaCl solution. The impedance modulus of ∼109 Ω.cm2 at a low frequency was obtained, which was five orders of magnitude higher than that for the AA2024-T3 alloy. Graphical Abstract: (Figure presented.) © The Author(s) 2024., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature.The research was funded by the European Union's Horizon 2020 research and innovation program under the H2020 - project FunGlass (Center for Functional and Surface Functionalized Glass), [grant agreement No. 739566] and the MICINN project TED2021-131258B-I00., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The influence of time dependent Al2O3 dissolution during melting on the structure-bioactivity correlation of Mg containing silica-based bioactive glasses

  • Başak, O.
  • Hruška, B.
  • Buňová, L.
  • Muñoz, Francisco
  • Michálek, M.
  • Chromčíková, M.
Alumina crucibles are less expensive than platinum crucibles. However, alumina crucibles tend to promote contamination of the melts, which affects the glasses, including their thermal and chemical properties. The unfavorable impact of Al2O3 on bioactivity has limited the use of alumina crucibles in bioactive glass production. However, research has also shown that a certain amount of Al2O3 enhances the resistance to crystallization without hindering bioactivity. MgO has shown a similar effect to Al2O3 on bioactive glasses, although there are conflicting results regarding the effect of MgO on the structure of silicate glasses. This study investigated the effect of MgO on the structure of silica-based bioactive glasses under different melting conditions, with emphasis on the correlation between structure and bioactivity. Structural investigations revealed that replacing 50 % of MgO with CaO (in mol %) and alumina contaminations did not significantly affect the QSin unit distribution. 31P MAS-NMR peaks shift to higher fields with MgO incorporation and alumina contaminations forming AlO4 tetrahedra in the glass network. The structural features of the glasses delay bioactivities but do not suppress them. Additionally, DTA results demonstrated synergistic improvement in thermal stability due to the presence of MgO and alumina contaminations. © 2024, This study was carried out in the framework of the project FunGlass, which has received funding from the European Union´s Horizon 2020 research and innovation programme under grant agreement No. 739566 and by the Slovak Grant Agency for Science under the grant No. VEGA 1/0021/23 and by the Research and Development Support Agency APVV-21-0016. The authors gratefully acknowledge Dr. Helena Palkova's assistance with the FTIR data and Dr. Hana Kankova's assistance with the XRF measurements., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Pressure-assisted sintering approaches for up-converting LiYF4:Er/Yb transparent oxyfluoride glass-ceramics

  • Truong, Mai-Phuong
  • Michálková, M.
  • Sedano, Mercedes
  • Pascual, M. Jesús
  • Klement, R.
Glasses of compositions 40SiO2-25Al2O3-18Li2O-7LiF-(10-x-y)YF3-xErF3-yYbF3 (mol.%, x = 0.1, 0.5; y = 0, 0.4, 2, 4) were prepared by melt-quenching technique and milled into powders. Glass powder pellets were treated by hot pressing at defined temperatures to obtain the corresponding glass-ceramics (GCs). High-resolution TEM and XRD analysis revealed the crystallization of LiYF4 and LiAlSiO4 phases with nano-crystal size below 50 nm, resulting in translucent GCs. The density of GCs was 98–99.5 % compared to parent glasses. GCs exhibited intense up-conversion emission when excited by near-infrared light at 980 nm. As Er3+ concentration increased from 0.1 to 0.5 mol.% in the samples, notable enhancement in green and red emission intensities was indicated. Yb3+ ions significantly facilitated up-conversion emission through energy transfer to Er3+ ions, resulting in a higher luminescence yield compared to Er3+ single-doped GCs. The tuning of the red to green emission intensity ratio can be achieved by varying Er3+ and Yb3+ concentrations and Er3+/Yb3+ ratio. © 2024 The Author(s), This project has received fundings from the European Union\u00B4s Horizon 2020 research and innovation programme under grant agreement No 739566, the MICINN grant No PID2020-115419GBC-21/C-22/AEI/10.13039/501100011033. The authors are grateful to the JECS Trust for financing the 3-month visit to ICV-CSIC Madrid (Contract No. 2022330). The authors also gratefully acknowledge the financial support from the Slovak Grant Agency of the Ministry of Education, Science, Research and Sport, VEGA 1/0476/22., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Novel self-healing glass-like CexOY film on a Flash-PEO coated AZ31B Mg alloy

  • Merino, Emilia
  • Cere, S.
  • Durán, Alicia
  • Castro Martín, Yolanda
The aim of this work is to develop a glass-like CexOy coating to seal the pores of a Flash-PEO coated AZ31B Mg alloy and simultaneously provide smart self-healing corrosion protection. The cerium sol was synthesized using cerium acetate as main precursor by sol-gel method. SEM micrographs revealed that upon cerium sol deposition, the pores of the oxide coating were effectively sealed, resulting in a double-layer coating system and thereby in a big reservoir of cerium ions (Ce3+/Ce4+). The glassy character of the cerium coating, confirmed by X-Ray diffraction, implies that cerium exists in Ce3+ and Ce4+ ionic states enclosed in a high internal energy structure which facilitate the diffusion of cerium ions to active cathodic zone. Electrochemical Impedance Spectroscopy (EIS), X-Ray Diffraction (XRD), and Raman spectroscopy were used to explore the active corrosion protection of the CexOy sol-gel coating. The corrosion inhibition mechanism involves the migration of cerium ions and the precipitation of insoluble-crystalline cerium compounds (CeO2). The coating demonstrated self-healing properties, presenting a promising alternative to traditional chrome conversion coatings (CCC). © 2024, This article is a part of the dissemination activities of MICINN project TED2021-131258B-I00, and the project FunGlass, which has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement No 739566., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Tesis doctoral (DoctoralThesis)

Modelización termodinámica de la estructura y conductividad iónica de vidrios de fosfato y oxinitruros

  • López-Grande, Alberto
[ES] En los últimos años, los vidrios de fosfato han adquirido una creciente relevancia debido a su potencial como electrolitos en baterías de estado sólido. Estas baterías representan una prometedora alternativa a las tradicionales, gracias a su alta densidad de energía, mayor seguridad y estabilidad frente a altas temperaturas. Los vidrios de fosfato presentan propiedades iónicas y estructurales únicas que los convierten en una opción atractiva como electrolitos en baterías de estado sólido. Es importante mencionar también las capas delgadas (amorfas) de oxinitruros de litio y fósforo, conocidas como LiPON, que contribuyen a mejorar la conductividad iónica y la durabilidad química del material. Estas capas ya se emplean comercialmente en microbacterias de estado sólido. Por consiguiente, la modelización de la estructura y las propiedades fisicoquímicas de estos vidrios y oxinitruros se presenta como un área de gran interés para la investigación en baterías de estado sólido. Su estudio puede tener un impacto significativo en el desarrollo de materiales más eficientes y seguros para aplicaciones de almacenamiento de energía. En el contexto de esta Tesis doctoral, se plantea una hipótesis fundamental: es factible predecir la estructura de distintos vidrios y otros sólidos amorfos mediante la modelización termodinámica de la interacción de los óxidos reaccionantes que conforman el sistema vítreo. Esta modalización permitiría, a su vez, prever la conductividad iónica de dichos materiales, abriendo nuevas perspectivas para el avance en este campo. A lo largo de la Tesis se presentan los resultados de la modelización de la estructura y las propiedades fisicoquímicas de los vidrios de fosfato y oxinitruros utilizando las leyes fundamentales de la química y la termodinámica, así como la validación de dicha modelización mediante la comparación de los resultados obtenidos con medidas experimentales. Partiendo del punto anterior, se presenta también la predicción de la conductividad iónica de estos materiales y la comparación de dicha predicción con los resultados obtenidos a partir de medidas experimentales, [EN] In recent years, phosphate glasses have gained increasing relevance due to their potential as electrolytes in solid-state batteries. These batteries ofer a promising alternative to traditional ones, thanks to their high energy density, improved safety, and stability at high temperatures. Phosphate glasses exhibit unique ionic and structural properties that make them an attractive option as electrolytes in solid-state batteries. It is also worth mentioning the thin layers (amorphous) of lithium and phosphorus oxynitrides, known as LiPON, which enhance the ionic conductivity and chemical durability of the material. These layers are already commercially used in micro solid-state batteries. Therefore, modeling the structure and physicochemical properties of these phosphate glasses and oxynitrides presents an area of great interest for solid-state battery research. Such investigations can have a signifcant impact on the development of more efcient and safer materials for energy storage applications. In the context of this doctoral thesis, a fundamental hypothesis is proposed: it is feasible to predict the structure of diferent glasses and other amorphous solids through thermodynamic modeling of the interaction of the reacting oxides that form the glass system. This modeling would, in turn, enable the prediction of the ionic conductivity of these materials, opening new perspectives for advancements in this feld. Throughout the thesis, the results of modeling the structure and physicochemical properties of phosphate-based glasses and oxynitrides using the fundamental laws of chemistry and thermodynamics are presented. The validation of this modeling is carried out by comparing the obtained results with experimental measurements. Building on the previous point, the prediction of the ionic conductivity of these materials is also presented, and this prediction is compared with the results obtained from experimental measurements, Este trabajo ha sido financiado por los siguientes proyectos: Proyecto FunGlass, programa de investigación e innovación Horizon 2020 de la Unión Europea, acuerdo de subvención N.º 739566. Proyecto de generación de conocimiento PID2020-115419-GB-C21, Ministerio de Ciencia e Innovación, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Tesis doctoral (DoctoralThesis)

Sistema integrado de recubrimientos anticorrosivos con efecto auto-curado para aleaciones ligeras combinando el proceso de anodizado y el proceso Sol-Gel: procesamiento y caracterización

  • Merino, Emilia
Tesis Doctoral inédita leída en la Universidad Autónoma de Madrid, Facultad de Ciencias, Departamento de Químia Física Aplicada. Fecha de Lectura: 12-03-2024 Esta Tesis tiene embargado el acceso al texto completo hasta el 12-09-2025, El trabajo de investigación de la presente tesis doctoral se ha llevado a cabo en el marco del proyecto Europeo “Centre for funcional and Surface-functionalized glasses” (FunGlass) No739566 y es parte de las actividades de diseminación del proyecto MICINN TED2021-131258B-I00, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Tesis doctoral (DoctoralThesis)

Multifunctional coatings on glass by sol-gel method for different applications, Recubrimientos multifuncionales preparados por sol-gel sobre sustratos de vidrio para diferentes aplicaciones

  • Haritha, Ajitha Haridasan
Tesis Doctoral inédita cotutelada por la Trenčianska Univerzita Alexandra Dubčeka V Trenčíne (Eslovaquia) y por la Universidad Autónoma de Madrid, Facultad de Ciencias, Departamento de Química Inorgánica. Fecha de Lectura: 16-12-2024, [EN] Thin film technology plays an important role in our day-to-day life. This technology involves the application of thin layers of materials, often at the micron or nanometer scale, onto different substrates. Thin films can alter the properties of these substrates and impart certain functionality. In recent years, coatings with multifunctionality through surface functionalization concepts have attracted significant interest in the glass industry. This is mainly due to their numerous applications, such as in solar cells, smart windows, and photocatalysis. In this research, the sol-gel method is used to obtain coatings with different functionalities such as antireflective, hydrophobic, photocatalytic, antibacterial and electrochromic properties. The sol-gel method is preferred over other deposition techniques such as pulsed laser deposition, chemical vapor deposition, and magnetron sputtering since it yields high-quality coatings at a low-cost and with a simple deposition procedure. In the scope of this research, coatings consisting of silica-titania (SiO2-TiO2) and triethoxy(octyl)silane (OTES)-modified SiO2 sol were deposited onto glass substrates to achieve antireflective and hydrophobic functionalities. On the other hand, zinc oxide (ZnO) and silver nanoparticle (AgNP) doped ZnO thin film were used to obtain photocatalytic and antibacterial properties. In addition, the ZnO thin film deposited on fluorine-doped tin oxide (FTO) glass was utilized as a counter electrode in a tungsten trioxide (WO3)-based electrochromic device. Thus, this research work is divided into three main parts based on the functionalities of the coating. In the first part of the research work, a double-layer coating was designed and fabricated on glass surfaces by sol-gel method using a silica-titania (SiO2-TiO2) thin film as the bottom layer and an inorganic-organic octyl triethoxy silane (OTES) modified SiO2 upper layer. The refractive index of the SiO2-TiO2 and OTES-modified SiO2 layers were 1.79 and 1.45, and their thicknesses were approximately 76.8 nm and 94.2 nm, respectively. A uniform and crack-free SiO2/SiO2-TiO2 coating was obtained with a percentage transmission of 99.1 in the visible region of the solar spectrum at 550 nm wavelength and with good hydrophobicity (contact angle of 104º). The developed multilayer coating can function as an antireflective and self-cleaning coating as cover glass on top of solar cells. In the second part, ZnO thin films on glass substrates were prepared via sol-gel by dip-coating technique to use them as photocatalyst. The effect of annealing temperature (300-550 ºC) of the ZnO thin film in the degradation of organic methyl orange (MO) dye using a solar simulator was evaluated. The photocatalytic properties of the ZnO films were also analyzed as a function of the optical, morphology, and compositional properties. XRD and Raman analysis confirmed the hexagonal wurtzite structure of ZnO. On the other hand, homogeneous, crack-free, and spherical-like features of ZnO films were observed from the SEM micrograph. The percentage transmission of all ZnO films annealed at different temperatures was > 80% in the 400–800 nm wavelength range. The best photocatalytic activity under solar radiation was shown by ZnO thin film annealed at 450 ºC. ZnO films developed can accelerate the degradation of MO, one of the main water pollutants found in the effluent from the textile and paper sectors. Furthermore, silver nanoparticles (AgNPs) were also incorporated into the ZnO film to evaluate their effect on the photocatalytic performance and their potential use as antibacterial coating. As-prepared AgNPs have been incorporated into ZnO sols to produce AgNP-doped ZnO sol (Ag-ZnO) and Ag-ZnO coatings were developed using simple sol-gel dip coating. The photocatalytic activity was studied through the degradation of methyl orange in aqueous solution under solar simulator. A significant improvement of the photocatalytic activity was observed for the Ag-ZnO coatings compared to coatings without Ag. The coating using 3 mol% AgNP in ZnO showed the best photocatalytic activity. This effect can be attributed to the role of silver in enhancing the efficiency of superoxide anion radical and hydroxyl radical generation. Antibacterial application of ZnO and AgNP doped ZnO thin films using Escherichia coli (E.coli) as a model for gram-negative bacteria, and Staphylococcus aureus (S. aureus) as gram-positive bacteria was also studied. AgNP-doped ZnO exhibited superior antibacterial activity relative to undoped ZnO thin films. Finally, in the third part, the fabrication of electrochromic devices using sol-gel-derived metal oxide thin films was used. Electrochromic devices (ECD) have attracted significant interest in the past two years for their potential uses in a wide variety of applications such as optical displays, anti-glare automobile rear-view mirrors, and smart windows. However, challenges such as simple and cost-effective electrochromic material preparation, insufficient coloration, lengthy switching times, and poor cycling stability still need to be overcome. In the thesis, an electrochromic device is fabricated by combining WO3 thin film as a working electrode and a ZnO thin film as a counter electrode on FTO glass substrates by a simple sol-gel spin coating method. Graphite-coated FTO (C-based ECD) was also used as a counter electrode for a comparative analysis of the ECDs. X-ray diffraction (XRD) studies showed that WO3 and ZnO films were well crystallized in monoclinic and hexagonal wurtzite structures with crystallite sizes of 38.5 and 42.2 nm, respectively. Field emission scanning electron microscopy (FE-SEM) images confirmed the formation of porous and nanorod-like structures for WO3 and ZnO films, respectively. Furthermore, the research results showed that the optical contrast at 600 nm of WO3-ZnO ECD was almost twice that of the WO3-C-based ECD. Cyclic voltammetry and chronoamperometry measurements were also used to study the electrochromic properties of the films., I am grateful to the European Union's Horizon 2020 research and innovation programme (grant agreement No. 739566), as well as projects VEGA 1/0844/21 and VEGA 1/0431/18 of the Grant Agency of Slovak Republic. Additionally, I thank the Journal of the European Ceramic Society (JECS) Trust for funding my mobility projects at CSIC-ICV, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Fabrication of Al2O3-Y3Al5O12-ZrO2 composites by single-step spark plasma sintering

  • Vakhshouri, Maryam
  • Talimian, Ali
  • Najafzadehkhoee, Aliasghar
  • Gallardo-López, Ángela
  • Poyato, Rosalía
  • Gutiérrez-Mora, Felipe
  • Galusek, Dušan
Fabricating Al2O3-Y3Al5O12-ZrO2 ceramic composites with a eutectic microstructure is challenging and costly, as it requires high-temperature melting of precursor materials. Here, we report on the successful production of Al2O3-Y3Al5O12- 5 mol% ZrO2 composites with lamellar eutectic microstructure through single-step spark plasma sintering (SPS) of sol-gel synthesized powder. The release of volatile species from partially calcined powders, due to limited calcination at 1000°C for 2 h, as well as their fine particle size, were used to create the conditions for local electric discharge and plasma formation during SPS; this resulted in the local formation of eutectic liquids, enabling the formation of lamellar microstructures. The microstructural features can be tailored by modifying the calcination process., This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 739566. Financial support of this work by the grants APVV 19–0010, and VEGA 2/0028/21 is gratefully acknowledged. This work also recieved support from GlaScratch project Funded by the European Union NextGenerationEU through the Recovery and Resilience Plan for Slovakia under the project No. 09I01–03-V04–00014/2024/VA. We appreciate the support provided by JECS TRUST under contracts 2021286, 2022320, and 2023349. Dr. Najafzadehkhoee acknowledges the support funded by the EU NextGenerationEU through the Recovery and Resilience Plan for Slovakia under the project No. 09I03–03-V04–00196. The authors would like to thank the aid of CITIUS at the University of Seville for using the SPS facility., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ionic conductivity of Li2O–P2O5 glasses from thermodynamic modeling of their chemical structure

  • López-Grande, Alberto
  • Dagupati, Rajesh
  • Galán del Sastre, Pedro
  • Muñoz, Francisco
Modeling the transport properties of glasses, and ionic conductivity in particular, has been a recurrent issue motivated for their high interest in the rapid developing field of energy conversion and storage devices for a wide range of applications such as in lithium rechargeable batteries. Despite the absolute conductivity of phosphate-based glasses is not among the highest, their ease of preparation and ability to host transition metals and secondary anions has contributed to foster their research from which good examples are the LiPON electrolytes or the LATP-based glass ceramics. In this work, the structure and ionic conductivity of lithium phosphate glasses with nominal composition (Formula presented.) Li<inf>2</inf>O⋅((Formula presented.))P<inf>2</inf>O<inf>5</inf>, and x between 46 and 58 mol%, have been studied through the thermodynamic approach of the associated solutions model that was introduced by Shakhmatkin and Vedishcheva in glasses. The weak electrolyte model and the Anderson and Stuart model have also been employed herein in order to calculate the activation energy of the conduction of lithium ions within the glass matrix. Experimental ionic conductivity and activation energy data have been determined and were compared with the ones calculated using the models mentioned above. The structural units of the network have also been obtained by means of the thermodynamic approach and compared with those determined by <sup>31</sup>P nuclear magnetic resonance (NMR) spectra. All of them showed that the glass network structure can be reliably represented by a solution of chemical species and whose properties can then be derived from the respective weights in the system., H2020 Spreading Excellence and Widening Participation, Grant/Award Number: 739566, Peer reviewed
Archivo Digital UPM
Publicación Artículo científico (JournalArticle)

Ionic conductivity of Li2O-P2O5 glasses from thermodynamic modeling of their chemical structure

  • López Grande, Alberto|||0000-0002-8551-4283
  • Dagupati, Rajesh|||0000-0002-6331-7860
  • Galán del Sastre, Pedro|||0000-0002-4600-9954
  • Muñoz Fraile, Fracisco|||0000-0002-7322-6559