Pasar al contenido principal

IDRIOS Y VITROCERAMICOS LUMINISCENTES DE ALTA CALIDAD OPTICA PARA APLICACIONES FOTONICAS

MAT2017-87035-C2-1-P

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de Fomento de la Investigación Científica y Técnica de Excelencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D (Excelencia / Generación de Conocimiento)
Año convocatoria 2017
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 29
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Transparent glass-ceramics produced by sol-gel: A suitable alternative for photonic materials

  • Gorni, Giulio
  • Velázquez, J. J.
  • Mosa Ruiz, Jadra
  • Balda, Rolindes
  • Fernández, Joaquín
  • Durán, Alicia
  • Castro Martín, Yolanda
This article belongs to the Special Issue Sol-Gel Chemistry Applied to Materials Science., Transparent glass-ceramics have shown interesting optical properties for several photonic applications. In particular, compositions based on oxide glass matrices with fluoride crystals embedded inside, known as oxyfluoride glass-ceramics, have gained increasing interest in the last few decades. Melt-quenching is still the most used method to prepare these materials but sol-gel has been indicated as a suitable alternative. Many papers have been published since the end of the 1990s, when these materials were prepared by sol-gel for the first time, thus a review of the achievements obtained so far is necessary. In the first part of this paper, a review of transparent sol-gel glass-ceramics is made focusing mainly on oxyfluoride compositions. Many interesting optical results have been obtained but very little innovation of synthesis and processing is found with respect to pioneering papers published 20 years ago. In the second part we describe the improvements in synthesis and processing obtained by the authors during the last five years. The main achievements are the preparation of oxyfluoride glass-ceramics with a much higher fluoride crystal fraction, at least double that reported up to now, and the first synthesis of NaGdF₄ glass-ceramics. Moreover, a new SiO₂ precursor was introduced in the synthesis, allowing for a reduction in the treatment temperature and favoring hydroxyl group removal. Interesting optical properties demonstrated the incorporation of dopant ions in the fluoride crystals, thus obtaining crystal-like spectra along with higher efficiencies with respect to xerogels, and hence demonstrating that these materials are a suitable alternative for photonic applications., This work was supported by MINECO under projects MAT2013-48246-C2-1-P, MAT2013-48246-C2-2-P, and MAT2017-87035-C2-1-P/-2-P (AEI/FEDER, UE) and Basque Country Government IT-943-16 and PPG17/07. The authors are grateful for access to the Spanish Beamline (SpLine) at the ESRF facilities in Grenoble to perform experiments MA-3350 and 25-01-1014. Jose Joaquín Velázquez also acknowledges MINECO for Grant FPDI-2013-16895., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Transparent Sol-Gel Oxyfluoride Glass-Ceramics with High Crystalline Fraction and Study of RE Incorporation

  • Gorni, Giulio
  • Velázquez, J. J.
  • Mosa Ruiz, Jadra
  • Mather, Glenn C.
  • Serrano Rubio, Aída
  • Vila, María
  • Castro, Germán R.
  • Bravo, David
  • Balda, Rolindes
  • Fernández, Joaquín
  • Durán, Alicia
  • Castro Martín, Yolanda
Transparent oxyfluoride glass-ceramic films and self-supported layers with composition 80SiO<sub>2</sub>-20LaF<sub>3</sub> doped with Er<sup>3+</sup> have been successfully synthesized by sol-gel process for the first time. Crack-free films and self-supported layer with a maximum thickness up to 1.4 µm were obtained after heat treatment at the low temperature of 550 °C for 1 min, resulting in a LaF<sub>3</sub> crystal fraction of 18 wt%, as confirmed by quantitative Rietveld refinement. This is the highest value reported up to now for transparent oxyfluoride glass-ceramics prepared by sol-gel. This work provides a new synthesis strategy and opens the way to a wide range of potential applications of oxyfluoride glass-ceramics. The characterization by a wide range of techniques revealed the homogeneous precipitation of LaF<sub>3</sub> nanocrystals into the glass matrix. X-ray absorption spectroscopy and electron paramagnetic resonance confirmed that the Er<sup>3+</sup> ions are preferentially embedded in the low phonon-energy LaF<sub>3</sub> nanocrystals. Moreover, photoluminescence (PL) measurements confirmed the incorporation of dopants in the LaF<sub>3</sub> nanocrystals. The effective concentration of rare-earth ions in the LaF<sub>3</sub> nanocrystals is also estimated by X-ray absorption spectroscopy., This research was funded by Spanish National projects MAT2017-87035-C2-1-P/2-P (AEI/FEDER, UE), MAT2016-75362-C3-1-R, and Basque Country University PPG17/07 and GIU17/014, We acknowledge support by the CSIC Open Access Publication Initiative through its Unit of Information Resources for Research (URICI)
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A highly efficient method of dehydroxylation and fining of Nd phosphate laser glasses

  • Muñoz, Francisco
  • Balda, Rolindes
We describe herein a method that shows to be highly efficient in the dehydroxylation and fining process of phosphate glasses and that has been tested on the Nd‐doped 15Na2O‐15K2O‐20BaO‐50P2O5 metaphosphate composition. The method consists of a two‐step procedure: first, the batch is melted in a ceramic crucible; then, the obtained glass is re‐melted under a constant N2 flow, while being placed inside a graphite crucible with a much bigger surface area as compared to its depth. This allows the melt to be spread over the crucible area resulting in a relatively thin layer with a high area in contact with the atmosphere at the temperature of remelting. It has been demonstrated that the water content decreases with both temperature and time length and that the glass samples obtained are completely free of bubbles and stria showing very high chemical and optical homogeneity. This method employed, has been proven to be very effective, as evidenced by the great increase in the lifetime of Nd3+ luminescence––reaching a maximum of 380 μs‐which is much higher than the one measured in the untreated glass., The authors thank funding from projects MAT2017‐87035‐C2‐1‐P/‐2‐P (AEI/FEDER, UE), and GIU17/014 (BasqueCountry University).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Tunable upconversion emission in NaLuF4-glass-ceramic fibers doped with Er3+ and Yb3+

  • Gorni, Giulio
  • Velázquez, J. J.
  • Kochanowicz, Marcin
  • Dorosz, Dominik
  • Balda, Rolindes
  • Fernández, Joaquín
  • Durán, Alicia
  • Pascual, M. Jesús
[EN] Novel glass-ceramic optical fibers containing NaLuF nanocrystals doped with 0.5ErF and 2YbF (mol%) have been prepared by the rod-in-tube method and controlled crystallization. NaLuF nanocrystals with a size around 20 nm are obtained after heat treatment at 600 °C. Intense upconverted green and red emissions due to (H, S) → I and F → I transitions, respectively, together with a blue emission due to H → I transition have been observed under excitation at 980 nm. The intensity of the green and red upconversion bands shows a nearly linear dependence on the excitation power which can be explained by saturation effects in the intermediate energy states and proves that a sensitized energy transfer upconversion process is responsible for the population of the emitting levels of Er ions. The upconversion emission color changes from yellow to green by increasing the excitation power density which allows to manipulate the color output of the Er emission in the glass-ceramic fibers. The tunable emission color is easily detected with the naked eye. This interesting characteristic makes these glass-ceramic fibers promising materials for photonic applications., This work was supported by MINECO under the project MAT2017-87035-C2-1-P/-2-P (AEI/FEDER, UE) and Basque Country University PPG17/07 and GIU17/014, and Basque Government PIBA2018-24. Funding from MPNS Cost Action MP1401 is also acknowledged. This paper is a part of dissemination activities of project FunGlass. This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement no. 739566.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación

Role of the La/K Compositional Ratio in the Properties of Waveguides Written by Fs-Laser Induced Element Redistribution in Phosphate-Based Glasses

  • Moreno-Zarate, Pedro
  • Muñoz, Francisco
  • Sotillo, Belén
  • Macías-Montero, M.
  • Atiénzar, Julia
  • Garcia-Pardo, Marina
  • Fernández, Paloma
  • Serna, Rosalía
  • Solís Céspedes, Javier
The local modification of the composition of glasses by high repetition femtosecond laser irradiation is an attractive method for producing photonic devices. Recently, the successful production of waveguides with a refractive index contrast (Δn) above 10<sup>−2</sup> by fs-laser writing has been demonstrated in phosphate glasses containing La<sub>2</sub>O<sub>3</sub> and K<sub>2</sub>O modifiers. This large index contrast has been related to a local enrichment in lanthanum in the light guiding region accompanied by a depletion in potassium. In this work, we have studied the influence of the initial glass composition on the performance of waveguides that are produced by fs-laser induced element redistribution (FLIER) in phosphate-based samples with different La and K concentrations. We have analyzed the contribution to the electronic polarizability of the different glass constituents based on refractive index measurements of the untreated samples, and used it to estimate the expected index contrast caused by the experimentally measured local compositional changes in laser written guiding structures. These estimated values have been compared to experimental ones that are derived from near field images of the guided modes with an excellent agreement. Therefore, we have developed a method to estimate before-hand the expected index contrast in fs-laser written waveguides via FLIER for a given glass composition. The obtained results stress the importance of considering the contribution to the polarizability of all the moving species when computing the expected refractive index changes that are caused by FLIER processes., This research was funded through grant numbers TEC2017-82464-R, MAT2017-87035-C2-1-P,and RTI2018-096498-B-I00 (MCIU/AEI/FEDER, EU).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Glass-Ceramics Processed by Spark Plasma Sintering (SPS) for Optical Applications

  • Singarapu, Babu
  • Galusek, Dušan
  • Durán, Alicia
  • Pascual, M. Jesús
© 2020 by the authors., This paper presents a review on the preparation of glass-ceramics (GCs) and, in particular, transparent GCs by the advanced processing technique of spark plasma sintering (SPS). SPS is an important approach to obtain from simple to complex nanostructured transparent GCs, full densification in a short time, and highly homogeneous materials for optical applications. The influence of the different processing parameters, such as temperature, pressure, sintering dwell time on the shrinkage rate, and final densification and transparency, are discussed and how this affects the glass material properties. Normally, transparent glass-ceramics are obtained by conventional melt-quenching, followed by thermal treatment. Additionally, the GC scan is produced by sintering and crystallization from glass powders. Hot pressing techniques (HP) in which the source of heating is high-frequency induction can be also applied to enhance this process. In the case of transparent ceramics and glass-ceramics, spark plasma sintering is a promising processing tool. It is possible to enhance the material properties in terms of its compactness, porosities, crystallization, keeping the size of the crystals in the nanometric scale. Moreover, the introduction of a high concentration of active gain media into the host matrix provides functional glass-ceramics systems with enhanced luminescence intensity through reducing non-radiative transitions like multi phonon relaxation (MPR) and cross relaxations (CR), thus providing longer lifetimes. More effort is needed to better understand the sintering mechanisms by SPS in transparent GC systems and optimize their final optical performance., Funding from the project MAT2017-87035-C2-1-P/2-P (AEI/FEDER, UE) is acknowledged. This paper is a part of the dissemination activities of project FunGlass. This project has received funding from the European Union’s Horizon 2020 research and innovation program under grant agreement No. 739566. Funding from the project VEGA 1/0527/18 is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Novel sol-gel SiO2-NaGdF4 transparent nano-glass-ceramics

  • Velázquez, J. J.
  • Mosa Ruiz, Jadra
  • Gorni, Giulio
  • Balda, Rolindes
  • Fernández, Joaquín
  • Durán, Alicia
  • Castro Martín, Yolanda
Novel transparent oxyfluoride nano-glass-ceramics containing undoped and 0.5 Eu (mol%) doped NaGdF nanocrystals (NCs), were obtained by sol-gel for the first time. X-ray diffraction (XRD) confirms the precipitation of α- and β-NaGdF NCs with a size ranging between 5 and 24 nm. When the Na:Gd ratio, temperature and heating time are fixed to 0.95:1, 550–600 °C and 1–8 h, respectively, only the β-NaGdF phase precipitates. These results are confirmed by high-resolution transmission electron microscopy (HRTEM). The decomposition of trifluoroacetic acid (TFA) and the formation of fluoride lattice bonds were studied by Fourier transform infrared spectroscopy (FTIR). Thus, the sol-gel route permits NaGdF glass-ceramics to be obtained through the control of Na:Gd ratio, temperature and heating time. The incorporation of dopant ions in the NaGdF NCs was confirmed by photoluminescence measurements which show narrow and well-resolved Eu emission and excitation spectra in GCs. Moreover, the low asymmetry ratio values between the electric dipole (D → F) to the magnetic dipole (D → F) transitions indicate that Eu ions are incorporated in the NaGdF NCs. Furthermore, efficient Gd→ Eu energy transfer results in an enhancement of the reddish Eu emissions, further supported by fluorescence decay lifetimes., This work was supported by MINECO under Projects N° MAT2013-48246-C2-1-P/2-P and MAT2017-87035-C2-1-P/-2-P (AEI/FEDER, UE),and Basque Country University PPG17/07 and GIU17/014. This paperis a part of dissemination activities of the project FunGlass. This projecthas received funding from the European Union's Horizon 2020 researchand innovation programme under grant agreement No 739566
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Chemical and structural heterogeneities in Nd-doped oxynitride phosphate laser glasses

  • Muñoz, Francisco
  • Jiménez Riobóo, R. J.
  • Balda, Rolindes
The application of oxynitride glasses in optics has been limited due the issues inherent in their preparation that result in bubbles, metallic inclusions or opacity. Although the synthesis of oxynitride phosphates is easier than in silicates, due to their lower melt viscosity, the remaining water in the form of OH causes, for instance, the neodymium luminescence to be negatively affected. We report on the preparation of oxynitride Nd phosphate glasses that are submitted first to a dehydroxylation, so that their structure and properties can be studied as a function of the nitrogen content taking a completely homogeneous OH-free glass as the starting point of each synthesis. Raman and Brillouin Spectroscopy confirmed the segregation in oxide and N-enriched regions, and NMR of the glasses has been used to calculate the O/P ratio from the distribution of P(O,N)4 groups. The difference between this and the experimental one obtained from the elemental analyses confirms the segregation in oxide and oxynitride regions that is produced during the ammonolysis of the phosphate glass. The oxynitride glass network could thus be considered a non-homogeneous mixture of the oxide and the nitrided phases that are segregated due to the non-randomness of the nitridation reaction., The authors thank funding from projects MAT2017-87035-C2-1-P/-2-P, MAT2015-65356-C3-1-R, RTI2018-096918-B-C41 (AEI/FEDER, UE), GIU17/014 (Basque Country University, Spain) and PIBA18-24 (Basque Country Government, Spain)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The internal friction of lithium and sodium borophosphate glasses

  • Hockicko, Peter
  • Mizeráková, Jana
  • Muñoz, Francisco
Alkali borophosphate glasses have recently gained strong interest, not only for their fundamental importance due to the mixed glass former effect but also because of their potential applicability as solid state electrolytes in energy harvesting devices. In the present work, internal friction measurements of lithium and sodium borophosphate glasses have been performed in order to look for further insights on the relationships between the ionic conduction mechanism and the structure of the glasses that has been previously determined. Absorption of acoustic waves shows two marked internal friction peaks with activation energy in the range of the activation energy for the ionic conduction of the glasses between 0.5 and 0.7 eV. Furthermore, the substitution of phosphorus by boron network former results in the decrease of the activation energy associated to both processes in parallel to the E of the ionic conduction of alkali cations; and the relationship between the areas of both peaks suggests a change of the distribution of alkali ions between positions energetically different in agreement with the structural changes of the glass network., The authors would like to thank F. Černobila for technical assistance. This study was supported by project VEGA No. 1/0510/17 and ITMS: 26220120046 co-funded from EU sources and European Regional Development Fund. F.M. thanks also funding from project MAT2017-87035-C2-1-P (AEI/FEDER, UE).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The glass-forming ability explained from local structural differences by NMR between glasses and crystals in alkali metaphosphates

  • Muñoz, Francisco
  • Sánchez Muñoz, Luis
[EN] The glass forming ability of inorganic substances has traditionally been evaluated in kinetic terms related to the rate of spontaneous crystallization of their melts, which is related to viscosity from the macroscopic point of view. However, differences or similarities between the local structures of glasses and crystals of the same composition could have an additional influence on the kinetic ability to form a stable glass or a crystal from a melt. In this work, the local structure of alkali metaphosphate glasses and crystals has been analyzed by means of P MAS-NMR to demonstrate that the ability to form a glass is directly related to the differences between the atomic organization in the glassy states and the structure of the stable crystals at lower temperatures. This implies that chemical compositions having a similar atomic order in their glass and crystal structures will not easily develop the disordered long-range structure of glass., Agencia Estatal de Investigación/FEDER) MAT2017-87035-C2-1-P. The authors are thankful to G. Tricot from the University of Lille (France) for the acquisition of part of the NMR spectra.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Femtosecond laser direct inscription of 3D photonic devices in Er/Yb-doped oxyfluoride nano-glass ceramics

  • Vázquez de Aldana, Javier R.
  • Romero, Carolina
  • Fernández, Joaquín
  • Gorni, Giulio
  • Pascual, M. Jesús
  • Durán, Alicia
  • Balda, Rolindes
The fabrication of optical waveguides by direct femtosecond laser irradiation in Er3+/Yb3+ oxyfluoride nano-glass ceramics is investigated. Following the strategy of single line irradiation, a wide range of laser parameters can be used to obtain single-mode waveguides with nearly-gaussian modal profiles, in the visible and near-infrared. Measured propagation loss is 1.6 dB/cm for the optimum parameters (0.34 μJ/pulse and 20 μm/s scanning velocity), with no annealing after irradiation, and the induced refractive index contrast is Δn∼0.006 (at 800 nm). The multi-scan technique is used to gain control of the refractive index profiles thus producing multimodal structures. The active behavior of the waveguides is induced under ∼800 nm seeding and the co-propagating guidance of the erbium emission is demonstrated. The integration of photonic elements such as Y-splitters, both in 2D and 3D, as well as Mach-Zehnder interferometers, is also shown. Results demonstrate the optimum behavior of Er3+/Yb3+ oxyfluoride nano-glass ceramics as a host material for the integration of complex active photonic devices by femtosecond laser irradiation in the low repetition rate regime., Ministerio de Economía y Competitividad (FIS2017-87970R, MAT2017-87035-C2-1-P/-2-P); Consejería de Educación, Junta de Castilla y León (SA287P18); Euskal Herriko Unibertsitatea (GIU17/014); Eusko Jaurlaritza (PIBA2018-24)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Non-linear optical properties of Er3+–Yb3+-doped NaGdF4 nanostructured glass–ceramics

  • Velázquez, J. J.
  • Gorni, Giulio
  • Balda, Rolindes
  • Fernández, Joaquín
  • Pascual, Laura
  • Durán, Alicia
  • Pascual, M. Jesús
This article belongs to the Special Issue Preparation and Application of Nanostructured Glass–Ceramics and Nanocomposites., Transparent oxyfluoride glass–ceramics containing NaGdF4 nanocrystals were prepared by melt-quenching and doped with Er3+ (0.5 mol%) and different amounts of Yb3+ (0–2 mol%). The selected dopant concentration the crystallization thermal treatments were chosen to obtain the most efficient visible up-conversion emissions, together with near infrared emissions. The crystal size increased with dopant content and treatment time. NaGdF4 NCs with a size ranging 9–30 nm were obtained after heat treatments at Tg + 20–80 °C as confirmed by X-ray diffraction and high-resolution transmission electron microscopy. Energy dispersive X-ray analysis shows the incorporation of rare earth ions into the NaGdF4 nanocrystals. Near-infrared emission spectra, together with the up-conversion emissions were measured. The optical characterization of the glass–ceramics clearly shows that Er3+ and Yb3+ ions are incorporated in the crystalline phase. Moreover, visible up-conversion emissions could be tuned by controlling the nanocrystals size through appropriated heat treatment, making possible a correlation between structural and optical properties., This research was funded by Spanish National projects MAT2017-87035-C2-1-P/2-P (AEI/FEDER, UE), Basque Country University PPG17/07 and GIU17/014 and Basque Government PIBA2018-24. This study is part of the dissemination activities of project FunGlass. This project has received funding from the European Union’s Horizon 2020 research and innovation program under grant agreement No 739566. This study was also created in the frame of the project Centre for Functional and Surface Functionalized Glass (CEGLASS), ITMS code is 313011R453, operational program Research and innovation, co-funded from European Regional Development Fund., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A new sol–gel route towards Nd3+-doped SiO2–LaF3 glass-ceramics for photonic applications

  • Cruz, María Eugenia
  • Durán, Alicia
  • Balda, Rolindes
  • Fernández, Joaquín
  • Mather, Glenn C.
  • Castro Martín, Yolanda
Glass-ceramic materials with composition 0.9Nd3+–80SiO2–20LaF3 were successfully obtained and further heat-treated at 450 °C for 6 h. Stable and homogeneous LaF3 nanoparticle suspensions with and without Nd3+ were first prepared by a chemical route, incorporating polyvinylpyrrolidone (PVP) as dispersant. The suspensions were then concentrated and characterised by XRD, HRTEM and zeta potential, confirming that LaF3 crystallises as the only phase, with particle size around 16 nm. The suspensions were incorporated in a silica sol to obtain a 0.9Nd3+–20LaF3–80SiO2 particulate sol, xerogel and glass-ceramic. HRTEM confirmed the homogeneous incorporation of the doped nanocrystals into the SiO2 matrix without modification of the nanoparticle structure. Rietveld refinement was used to determine the crystallinity and quantity of LaF3 nanoparticles present in the glass-ceramic after treatment of the particulate sol at 450 °C for 6 h. Luminescence measurements of near infrared Nd3+ ion emissions in the lanthanum fluoride nanoparticles and SiO2–LaF3 glass-ceramic showed well-structured emission spectra with lifetimes similar to those of theoretical Nd+3 in LaF3 crystals., The authors acknowledge the financial support from MINECO under projects MAT2017-87035-C2-1-P/-2-P (AEI/FEDER, UE), Basque Country University GIU17/014 and Basque Government PIBA2018-24. This article is a part of the dissemination activities of the project FunGlass, which has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement no. 739566. The authors also acknowledge the support of the Transmission Electron Microscope (TEM) service of the Institute of Catalysis and Petrochemistry (CSIC)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nd3+doped- SiO2–KLaF4 oxyfluoride glass-ceramics prepared by sol-gel

  • Cruz, María Eugenia
  • Li, Jing
  • Gorni, Giulio
  • Durán, Alicia
  • Mather, Glenn C.
  • Balda, Rolindes
  • Fernández, Joaquín
  • Castro Martín, Yolanda
Neodymium (Nd3+) doped SiO2–KLaF4 oxyfluoride glass-ceramic (GCs) containing 10 mol% and 20 mol% of KLaF4 nanocrystals (NCs) were prepared for the first time by sol-gel and sintered at 550 °C. Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) were used to analyze the evolution of the xerogel during the heat treatment, high-resolution transmission electron microscopy (HRTEM) was employed to study the formation and distribution of NCs in the silica matrix. The decomposition of trifluoroacetic acid (TFA) and the crystallization of fluoride nanocrystals were also confirmed. The presence of α-KLaF4 and β-KLaF4 crystalline phases with maximum crystal sizes of 24 nm and 17 nm respectively were clearly observed after heat treatment at 550 °C for 1 min. Site-selective emission and excitation spectra confirmed the incorporation of Nd3+ ions in both crystalline phaseswith emission of Nd3+ most predominant in the β-KLaF4 NCs., The authors acknowledge the financial support from MINECO under projects MAT2017-87035-C2-1-P/-2-P (AEI/FEDER, UE), Basque Country University GIU17/014 and Basque Government PIBA2018-24. This article is a part of the dissemination activities of the project FunGlass, which has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement No 739566., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Femtosecond laser induced thermophoretic writing of waveguides in silicate glass

  • Macías-Montero, M.
  • Muñoz, Francisco
  • Sotillo, Belén
  • Hoyo, J. del
  • Ariza, Rocío
  • Fernández, Paloma
  • Siegel, Jan
  • Solís Céspedes, Javier
12 pags., 5 figs., 1 tab., Here in, the fs-laser induced thermophoretic writing of microstructures in ad-hoc compositionally designed silicate glasses and their application as infrared optical waveguides is reported. The glass modifcation mechanism mimics the elemental thermal difusion occurring in basaltic liquids at the Earth’s mantle, but in a much shorter time scale (108 times faster) and over a well-defned micrometric volume. The precise addition of BaO, Na2O and K2O to the silicate glass enables the creation of positive refractive index contrast upon fs-laser irradiation. The infuence of the focal volume and the induced temperature gradient is thoroughly analyzed, leading to a variety of structures with refractive index contrasts as high as 2.5 × ­10–2. Two independent methods, namely near feld measurements and electronic polarizability analysis, confrm the magnitude of the refractive index on the modifed regions. Additionally, the functionality of the microstructures as waveguides is further optimized by lowering their propagation losses, enabling their implementation in a wide range of photonic devices, Tis work was fnancially supported by the Spanish Research Agency (MCIU/AEI/Spain) and the European Regional Development Fund (ERDF) through Grants TEC2017-82464-R, MAT2017-87035-C2-1-P, and RTI2018-096498-B-I00. M. Macias-Montero acknowledges the postdoctoral Juan de la Cierva Incorporación grant (IJCI-2017-33317) of the Spanish Ministry of Research and Innovation. B.Sotillo and J. del Hoyo acknowledge the fnancial support from Comunidad de Madrid (Ayudas del Programa de Atracción de Talento, 2017-T2/ IND-5465 and 2019-T2/IND-12950). R. Ariza acknowledges the European Social Fund., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Competition effects during femtosecond laser induced element redistribution in Ba- and La-migration based laser written waveguides

  • Macías-Montero, M.
  • Moreno-Zarate, Pedro
  • Muñoz, Francisco
  • Sotillo, Belén
  • Garcia-Pardo, Marina
  • Serna, Rosalía
  • Fernández, Paloma
  • Solís Céspedes, Javier
15 pags., 5 figs., 4 tabs. -- This article belongs to the Special Issue Advanced Pulse Laser Machining Technology, Fs-laser induced element redistribution (FLIER) has been a subject of intensive research in recent years. Its application to various types of glasses has already resulted in the production of efficient optical waveguides, tappers, amplifiers and lasers. Most of the work reported on FLIER-based waveguides refers to structures produced by the cross-migration of alkali (Na, K) and lanthanides (mostly La). The latter elements act as refractive index carrying elements. Herein, we report the production of Ba-based, FLIER-waveguides in phosphate glass with an index contrast > 10−2 . Phosphate glasses modified with the same amount of Na2O and K2O, and variable amounts of BaO and/or La2O3 were used to produce the FLIER-waveguides with Ba and or La acting as index carriers. Ba-only modified glasses show a waveguide writing threshold and light guiding performance comparable to that of La-based structures. However, mixed Ba-La glasses show a much higher element migration threshold, and much smaller compositionally modified regions. This behavior is consistent with a competition effect in the cross-migration of both elements (Ba and La) against the alkalis. Such an effect can be applied to inhibit undesired element redistribution effects in fs-laser processing applications in multicomponent glasses., This research was funded through grant numbers TEC2017-82464-R, MAT2017-87035-C2-1-P, RTI2018-096498-B-I00 (MCIU/AEI/FEDER, EU), and CSIC PIE-201850E057 and PIE-202050E195 projects., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

X-ray absorption spectroscopy and neutron-diffraction study of persistent luminescent Sr2MgSi2O7 glass-ceramics

  • Fernández-Rodríguez, Laura
  • Gorni, Giulio
  • Mather, Glenn C.
  • Savvin, S.
  • Cuello, G. J.
  • Durán, Alicia
  • Pascual, M. Jesús
[EN] Glass-ceramics based on the Eu 2 O 3 /Dy 2 O 3 -doped Sr 2 MgSi 2 O 7 phosphor have been obtained from sinter- ing and crystallization of glass powders. The doped parent glasses show red emission under excitation of UV light. After thermal treatment, the corresponding glass-ceramics show persistent blue emission which emanates from Eu 2 + incorporated in the crystals; red emission also occurs from Eu 3 + in the residual vitreous phase. The aim of this work is to investigate the structure of defects such as oxygen and strontium vacancies in the Sr 2 MgSi 2 O 7 crystals and the environment, oxidation state and coordination of the Eu and Dy ions in the glass-ceramics, their partitioning between crystalline and glassy phase and their influence on lu- minescence properties, employing X-ray absorption spectroscopy (XAS) and neutron diffraction (ND) as investigative structural tools. We suggest that the luminescence mechanism involves the presence of shal- low electron traps that are abruptly emptied for temperatures above 100 K. The most persistent lumines- cence is likely due to an effective concentration of Eu 2 + in the dendritic-shaped crystals in one of the particular compositions, and with a suitable level of Sr vacancies, even though Sr vacancies are most likely formed in all the investigated samples., Funding from MINECO under project MAT2017–87035-C2–1-P/2-P (AEI/FEDER, UE) and from PIE-CSIC 201960E016 is acknowledged. Neutron diffraction measurements were carried out in D2B line under the experiment doi:10.5291/ILL-DATA.1–04–156. XANES and EXAFS experiments were performed at the BL22-CLAESS beamline at the ALBA synchrotron with the collaboration of ALBA staff under the experiment number AV-2020014045., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Silicate-based persistent phosphors

  • Fernández-Rodríguez, Laura
  • Durán, Alicia
  • Pascual, M. Jesús
[EN] Eu2+-doped alkaline-earth silicates are the second most studied group of persistent luminescent inorganic phosphors after aluminates, such as SrAl2O4. Silicates are comparable with the aluminates in terms of chemical stability, high quantum efficiency and large band gap, but offer advantages including better water resistance and lower calcination temperature. Their applications range from traditional uses such as traffic signs, tile decoration or fluorescent lamps to more advanced ones such as solar cells, LEDs or in the medical field. The highest persistence has been found in (Ca,Sr,Ba)3MgSi2O8: Eu2+, Dy3+, Ba4(Si3O8)2: Eu2+, Dy3+ or Sr2MgSi2O7: Eu2+, Dy3+. Various synthesis routes have been employed to obtain crystals of these phases, such as sol-gel, hydrothermal and combustion synthesis and, more commonly, solid-state reaction. The preparation of silicate phosphors from glass crystallization has not yet been widely explored. Here, we review the progress made in the research of these inorganic crystalline phosphors, the proposed persistent luminescence mechanisms taking place and the different preparation methods employed to date, with special attention paid to the Sr2MgSi2O7: Eu2+, Dy3+ phase due to its long afterglow emission., Funding from MINECO under project MAT2017-87035-C2-1-P/2-P(AEI/FEDER, UE) and from PIE-CSIC 201960E016 is acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Crystallization process and site-selective excitation of Nd3+ in LaF3/NaLaF4 sol–gel-synthesized transparent glass-ceramics

  • Cruz, María Eugenia
  • Li, Jing
  • Gorni, Giulio
  • Durán, Alicia
  • Mather, Glenn C.
  • Balda, Rolindes
  • Fernández, Joaquín
  • Castro Martín, Yolanda
This article belongs to the Special Issue Glass-Ceramics: Improving Glass Properties through Crystallization., In this study, transparent oxyfluoride glass-ceramics (GCs) with NaLaF4 nanocrystals (NCs) were prepared by the sol–gel method for the first time. Three different molar ratios of La(CH3COO)3/Na(CH3COO) were used to obtain the GCs, which were sintered at 450, 550 and 650 °C for 1 min. X-ray diffraction (XRD) was employed to follow the evolution of the xerogel during the heat treatments and to study crystal growth for the three temperatures. In all cases, the LaF3 crystalline phase was present, but crystallization of NaLaF4 was only promoted at 650 °C. Thermogravimetric and thermodifferential analysis (TGA-DTA) and Fourier transform infrared spectroscopy (FTIR) were used to analyze the crystallization process. High-resolution transmission electron microscopy (HRTEM) was employed to confirm NaLaF4 crystallization and determine the size distribution. The incorporation of Nd3+ ion into NaLaF4 and LaF3 nanocrystals was confirmed by site-selective emission and excitation spectra. The Nd3+ emission intensities in both phases depend not only on the NaLaF4/LaF3 ratio but also on their emission efficiencies., The authors acknowledge financial support from MINECO under projects MAT2017-87035-C2-1-P/-2-P (AEI/FEDER, UE), and Basque Government PIBA2018-24. This article is a part of the dissemination activities of the project FunGlass, which has received funding from the European Union’s Horizon 2020 research and innovation program under grant agreement No 739566., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Structural and optical properties in Tm3+/Tm3+–Yb3+ doped NaLuF4 glass-ceramics

  • Velázquez, J. J.
  • Balda, Rolindes
  • Fernández, Joaquín
  • Gorni, Giulio
  • Sedano, Mercedes
  • Durán, Alicia
  • Galusek, Dušan
  • Pascual, M. Jesús
Transparent NaLuF4 glass-ceramics (GCs) doped with Tm3+ and Tm3+/Yb3+ have been prepared by melting-quenching followed by thermal treatment at temperatures near the glass transition temperature. The crystallization process has been studied using X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM). NaLuF4 nanocrystals (NCs) ranging 9–30 nm in size are the only crystalline phase, the crystal size increasing with the dopant concentration. Energy dispersive X-ray (EDX) measurements confirm the Tm3+ and Yb3+ incorporation in the NCs. Optical characterization included the analysis of up-conversion (UC) as well as the Near-infrared (NIR) luminescence. NIR emission spectra of Tm3+ and Yb3+ in co-doped samples confirmed an efficient energy transfer between both ions. No UC emissions are observed in Tm3+ single-doped glass and GCs. Yb3+ incorporation favors the Tm3+-Tm3+ UC processes resulting in Tm3+ blue, yellowish-red and NIR UC emissions after excitation at 975 nm. Blue UC emission is also observed in the codoped samples after Tm3+ excitation at 791 nm. These effects were more evident for the GCs compared to the base glasses, confirming the RE ions incorporation in the NCs. As a result, these GCs can be used to tune the UC emission from NIR to blue by selective excitation., This work was supported by MINECO under Projects MAT2017-87035-C2-1-P/-2-P (AEI/FEDER, UE), Basque Country Government PIBA2018-24 and Basque Country University GIU17/014. This article is part of the dissemination activities of project FunGlass. This project has received funding from the European Union´s Horizon 2020 research and innovation programme under grant agreement No 739566. This article was also created in the frame of the project Centre for Functional and Surface Functionalized Glass (CEGLASS), ITMS code is 313011R453, operational program Research and innovation, co-funded from European Regional Development Fund. This research work has been supported by the Research Agency of the Ministry of Education, Science, Research and Sport of the Slovak Republic, by the project: Advancement and support of R&D for "Centre for diagnostics and quality testing of materials" in the domains of the RIS3 SK specialization, Acronym: CEDITEK II., ITMS2014+ code 313011W442., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Control of degradation rate of Mg alloys using silica sol–gel coatings for biodegradable implant materials

  • Castro Martín, Yolanda
  • Durán, Alicia
[EN] Silica sol–gel coatings were deposited on AZ31B and AZ91D magnesium substrates with the aim of controlling the degradation rate, corrosion attack and further dissolution of magnesium alloys for temporal implants. Two different silica sols were prepared with and without colloidal silica particles (MTL and TG sols) and deposited by dip-coating on both alloys. The coatings were characterised in SBF using three different in vitro tests; hydrogen evolution, pH variation and potentiodynamic polarization curves. The results show that the corrosion behaviour depends on the alloy and on the coating composition. Coatings on AZ91D-MTL were able to block the degradation of the alloy during 8 days of immersion in SBF, whereas coatings AZ91D-TG only maintain their stability during 3 days. Mg(OH) and hydroxyapatite (HAp) were identified as the compounds precipitated on AZ31B samples, not appearing on AZ91D samples. The electrochemical tests confirm the promising corrosion results obtained for coated AZ91D samples., This work was supported by MINECO under Projects MAT2017-87035-C2-1-P/2-P (AEI/FEDER, UE). The authors would like to thank to Aritz Iglesias and Irene Ramirez Ruiz for their helpful in the develop of the experimental part., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of dopant precursors on the optical properties of rare‐earths doped oxyfluoride glass‐ceramics

  • Gorni, Giulio
  • Serrano Rubio, Aída
  • Bravo, David
  • Castro, Germán R.
  • Balda, Rolindes
  • Fernández, Joaquín
  • Durán, Alicia
  • Pascual, M. Jesús
[EN] TThe crystallization of fluoride nanocrystals (NCs) in chemically and mechanically stable aluminosilicate glasses has shown interesting optical properties even for small crystal fractions (10‐15 wt%). When rare‐earth (RE) ions are used as dopants, crys-tal‐like features can be reproduced and an increase in the emission and/or energy transfer processes, with respect to the starting glasses, is observed. A crucial point for these materials is the study of the local surrounding of RE ions and their incorpora-tion in the NCs. In fact, the effective concentration in the NCs can be much higher than the nominal concentration, up to one order of magnitude or even higher. The knowledge of RE ions incorporation in the NCs permits choosing proper doping lev-els to optimize both linear and nonlinear optical properties. In this work, transparent oxyfluoride glass‐ceramics with LaF3 NCs, doped with Nd3+ and Er3+ using oxide and fluoride precursors, were prepared using the melt‐quenching method and con-trolled crystallization. The local surrounding of the RE ions was studied using X‐ray absorption spectroscopy, electron paramagnetic resonance and photoluminiscence. The results show that most RE ions are already in a fluorine‐rich amorphous environ-ment even in the initial glass. The crystallization process provokes the RE ion redis-tribution and incorporation in the fluoride NCs. The different RE precursors, used as oxides or fluorides, have an influence on the incorporation of the RE in the NCs and, as a consequence, on the final optical properties., Comunidad de Madrid, Grant/Award Number: 2017‐t2/IND5395; European Synchrotron Radiation Facility; Ministerio de Ciencia e Innovación, Grant/Award Number: MAT2016‐75362‐C3‐1‐R; Euskal Herriko Unibertsitatea, Grant/Award Number: PPG17/07 and GIU17/014; MINECO, Grant/Award Number: MAT2017‐87035‐C2‐1‐P/‐2‐P; European Union, Grant/Award Number: 739566, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Integrated self-healing coating system for outstanding corrosion protection of AA2024

  • Castro Martín, Yolanda
  • Özmen, Eren
  • Durán, Alicia
[EN] This work reports the preparation of an integrated self-healing system that combines the anodization of Al-substrates with the deposition of environmentally friendly coatings prepared by sol-gel for obtaining an active corrosion protection of aluminum alloys AA2024. The system consists on a first step of forming appropriate anodized layers by controlling the potential and anodizing time. The second step is the infiltration of a cerium sol-gel sol and deposition of a Ce-glass like film, followed by a final hybrid silica sol-gel coating, creating an adherent, stable and active corrosion protective system. SEM, electrochemical techniques (potentiodynamic and EIS tests) as well as an accelerated corrosion test are used to analyze the structure of the coatings and to study the corrosion behavior of the different coatings on AA2024. The results of potentiodynamic measurements showed the excellent corrosion properties and EIS measurements confirmed the self-healing behavior by blocking the pitting defects. The outstanding self-healing corrosion protecting behavior provided by this integrated self-healing coating system offers an efficient chromium-free system for substituting chromium CCC and CCA coatings., This work was supported by Spanish MINECO under project MAT2017-87035-C2-1-PP. This paper is also part of dissemination activities of project FunGlass. This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 739566, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Processing and luminescence of Eu/Dy-doped Sr2MgSi2O7 glass-ceramics

  • Fernández-Rodríguez, Laura
  • Levy, David
  • Zayat, Marcos
  • Jiménez, J.
  • Mather, Glenn C.
  • Durán, Alicia
  • Pascual, M. Jesús
[EN] Glass-ceramics based on the Eu/Dy-doped SrMgSiO phosphor have been obtained from sintering and crystallization of glass powders. Electric and gas furnaces were employed for glass melting. The doped parent glasses show red emission under excitation of UV light whereas the corresponding glass-ceramics show blue emission. The microstructure of the glass-ceramics and the crystals responsible for the blue emission were observed by scanning electron microscopy-cathodoluminescence. The composition of the crystallised phases and the distribution and incorporation of rare-earth (RE) ions into the crystals and remaining glassy phase were determined by X-ray diffraction and energy dispersive X-ray analysis, respectively. Photoluminescence emission spectra showed a main peak at 484 nm assigned to the typical Eu transitions under excitation at 390 nm in the glass-ceramics. The presence of Dy improved persistence in the samples melted in the gas furnace. The glass-ceramics are sensitive to temperature, which modifies both the persistence time and red-blue luminescence., Funding from MINECO under project MAT2017-87035-C2-1-P/2-P (AEI/FEDER, UE) and from PID2019-107439GB-I00 project is acknowledged.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Dehydroxylation processing and lasing properties of a Nd alumino-phosphate glass

  • Muñoz-Quiñonero, Mónica
  • Azkargorta, Jon
  • Iparraguirre, Ignacio
  • Jiménez Riobóo, R. J.
  • Tricot, Gregory
  • Shao, Chongyoun
  • Muñoz, Francisco
  • Fernández, Joaquín
  • Balda, Rolindes
In this work, we have studied the preparation and properties of an alumino-phosphate glass with composition 13Na2O-13K2O-16BaO-4Al2O3-54P2O5 (mol%). The first part of the work deals with the study of the processing conditions of the dehydroxylation of the phosphate glass, which was performed by remelting under N2 flow using graphite crucibles. Glass samples from 5 to 50 g and Nd2O3 doped were submitted to dehydroxylation and the influence of temperature, time, mass of glass and viscosity were correlated with the content of water in the glasses through the coefficient of absorption of OH ions. The network structure of the glasses was also determined by means of 31P and 27Al 1D/2D nuclear magnetic resonance and the local environment of Nd3+ ions was probed by electron paramagnetic resonance. The optimized conditions of processing were then used to obtain a dehydroxylated glass with a 2.5 wt% Nd2O3 whose spectroscopic and laser emission properties were studied. The spectroscopic properties of Nd3+ ions which include, Judd-Ofelt calculation, stimulated emission cross-section of the laser transition, lifetime, and quantum efficiency are presented. Site-selective laser spectroscopy and stimulated emission obtained under selective wavelength pumping along the 4I9/2→4F5/2 absorption band were performed to determine the distribution of crystal field in which the rare earth is located, together with its influence in the pump wavelength dependence of the spontaneous and laser emissions of Nd3+ in this glass matrix., The authors thank funding from projects from Agencia Estatal de Investigación of Spain (FEDER, UE) MAT2017-87035-C2-1-P/-2-P, MAT2015-65356-C3-1-R, RTI2018-096918-B-C41, PID2020-115419GB-C21/C-22, and the project from the Basque Country Government PIBA1824., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

The chemistry of melting oxynitride phosphate glasses

  • Muñoz, Francisco
[EN] Oxide glasses are the most commonly studied non-crystalline materials in Science and Technology, though compositions where part of the oxygen is replaced by other anions, e.g. fluoride, sulfide or nitride, have given rise to a good number of works and several key applications, from optics to ionic conductors. Oxynitride silicate or phosphate glasses stand out among all others because of their higher chemical and mechanical stability and their research continues particularly focused onto the development of solid electrolytes. In phosphate glasses, the easiest way of introducing nitrogen is by the remelting of the parent glass under a flow of ammonia, a method that allows the homogeneous nitridation of the bulk glass and which is governed by diffusion through the liquid-gas reaction between NH3 and the PO4 chemical groupings. After nitridation, two new structural units appear, the PO3N and PO2N2 ones, where nitrogen atoms can be bonded to either two or three neighboring phosphorus, thus increasing the bonding density of the glass network and resulting in a quantitative improvement of their properties. This short review will gather all important aspects of the synthesis of oxynitride phosphate glasses with emphasis on the influence of chemical composition and structure., This work was funded by AEI/FEDER from project MAT2017-87035-C2-1-P.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

KLaF4:Nd3+ doped transparent glass-ceramics processed by spark plasma sintering

  • Babu, Singarapu
  • Balda, Rolindes
  • Fernández Lozano, José Francisco
  • Sedano, Mercedes
  • Gorni, Giulio
  • Cabral, A. A.
  • Galusek, Dušan
  • Durán, Alicia
  • Pascual, M. Jesús
Transparent oxyfluoride glass-ceramics (GCs) containing KLaF4 nanocrystals (NCs) doped with Nd3+were prepared by Spark Plasma Sintering (SPS). Glass powder pellets were sintered under a vacuum atmosphere, optimizing the processing parameters such as particle size, pressure, temperature, and holding time to obtain full densification. Transparency decreased when decreasing the particle size due to higher carbon contamination from the die. The α-KLaF4 crystalline phase was identified by X-ray diffraction (XRD) and its average crystal size was 10–20 nm. High-resolution transmission electron microscopy (HR-TEM) confirmed the presence of KLaF4 nanocrystals with incorporated Nd3+ions. Low-temperature site-selective emission and excitation spectra of Nd3+ions confirmed that α- KLaF4 was the predominant polymorph, although a minor presence of β- KLaF4 was also demonstrated., This work was supported by MINECO under Projects MAT2017–87035-C2–1-P/−2-P (AEI/FEDER, UE), PID2020–115419GB-C-21/C-22 and Basque Country Government PIBA2018–24. AAC also thanks the scholarships of the Federal Agency for the Support and Improvement of Higher Education (CAPES), contract #99999.002598/2015–09. This paper is part of the dissemination activities of project FunGlass. This project has received funding from the European Union´s Horizon 2020 research and innovation program under grant agreement No 739566., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Crystallization mechanism in sol-gel oxyfluoride glass-ceramics

  • Gorni, Giulio
  • Pascual, M. Jesús
  • Caballero Cuesta, Ángel
  • Velázquez, J. J.
  • Mosa Ruiz, Jadra
  • Castro Martín, Yolanda
  • Durán, Alicia
[EN] The crystallization mechanism of LaF in sol-gel oxyfluoride glass-ceramics in the system SiO-LaF has been studied using DTA, XRD, FTIR, HRTEM and NMR. Based on classical calculations of non-isothermal DTA curves involving Ozawas's plots, a diffusion-controlled process should be responsible for the fluorides crystallization similarly to that obtained for melt-quenching oxyfluoride glass-ceramics. Therefore, an increase of the crystal size and fraction is expected when increasing the time and/or temperature of the treatment. Nevertheless, XRD, FIR, HRTEM and NMR demonstrated that neither bigger crystals nor higher crystal fraction are obtained for treatment times longer than 1 min at 550 °C. However, further heat treatment causes that the structural order of the crystals is lost. On the other hand, typical fluorides crystallization temperatures (~300 °C) in sol-gel materials are much lower than T of the matrix (~1130 °C) thus being very different to what observed for oxyfluoride glasses prepared by melt-quenching. The proposed crystallization mechanism is a fast process that occurs when crystallization temperature is reached. This behavior is explained as a chemical reaction from the xerogels, followed by the fast precipitation of the nanocrystals without energy barrier. The nanocrystals are unstable in the surrounding SiO matrix for aging at crystallization or higher temperatures. These treatments lead to a dissolution process, favored by the compositional gradient between matrix and crystals, which drive the material to reach the equilibrium., This work was supported by MINECO under Project No.MAT2013-48246-C2-1-P and MAT2017-87035-C2-1-P/-2-P (AEI/FEDER, UE). J.J. Velázquez also acknowledges MINECO under Grant FPDI-2013-16895.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of barium substitution on the physical, thermal, optical and luminescence properties of Sm3+-doped metaphosphate glasses for reddish orange light applications

  • Mrabet, H.
  • Khattech, I.
  • Bouzidi, S.
  • Kechiche, L.
  • Jbeli, A.
  • Al Harbi, N.
  • Bouzidi, C.
  • Muñoz, Francisco
  • Balda, Rolindes
Our present study focuses on examining the thermal, structural and luminescent characteristics of sodium barium metaphosphate glasses doped with Sm3+. Glass samples with molar compositions (100 − y)[(50P2O5)-(50-xNa2O)-(xBaO)]-ySm2O3, where x = 20, 25, 30, 35, 40 and y = 0.3 and 1% were first synthesized by conventional melt quenching and later dehydroxylated under a constant N2 flow to ensure final glasses with a very high degree of chemical and optical homogeneity and free of water. Upon the addition of BaO and Sm2O3, refractive index, molar mass, density, glass transition temperature and dilatometric softening temperature exhibited an increase, whereas the coefficient of thermal expansion showed a decrease. The FTIR spectra analysis reveals a network depolymerization that intensifies with rising BaO concentration, ultimately transitioning from a modifier oxide to a glass-forming element, at higher BaO concentrations. All doped samples exhibited prominent absorption bands in the visible (VIS) and near-infrared (NIR) regions, as revealed by the optical absorption spectra. The Na2O modifier demonstrated greater influence on Sm3+ emission compared to BaO, a phenomenon that can explained by the moderation of the local ligand field strength resulting from this substitution. With an increase in Sm2O3 concentration from 0.3 to 1 mol%, the experimental lifetimes of the 4G5/2 level decrease, primarily attributed to the presence of energy transfer mechanisms. A discussion of Judd-Ofelt parameter analysis and glass radiation properties will be presented. © 2024 The Royal Society of Chemistry., The authors thank funding through projects MAT2017-87035-C2-1-P/-2-P from Agencia Estatal de Investigacion, PID2020-115419GB-C21/C22 from Agencia Estatal de Investigacion MCINN/AEI/10.13039/501100011033 and PIBA18-24 (Basque Country Government). The researchers would like to acknowledge Deanship of Scientific Research, Taif University., Peer reviewed