Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of pre-treatments on adhesion, barrier and mechanical properties of epoxy coatings: A comparison between steel, AA7075 and AA2024

  • Trentin, A.
  • Samiee, R.
  • Pakseresht, A.H.
  • Durán, Alicia
  • Castro Martín, Yolanda
  • Galusek, D.
Supplementary material associated with this article can be found, in the online version, at doi:10.1016/j.apsadv.2023.100479., [EN] In this work five independent pre-treatments – mechanical polishing, alkaline and acid etching, sol-gel primer, and anodizing – were applied on mild steel and aluminum (AA7075 and AA2024) substrates before the deposition of epoxy coatings. The results demonstrate that efficient adhesion can be achieved by simple methodologies and widely available chemicals as an alternative to toxic conversion layers or highly energetic processes. All the treatments provided higher adhesion (up to 75%, 61% and 14% on AA7075, AA2024 and steel, respectively) and better anti-corrosion performance (increase of impedance values at low frequency up to four orders of magnitude) than the polished reference. The anodizing of aluminum alloys yielded good anti-corrosion performance, but slightly lower mechanical properties compared to sol-gel primer and alkaline etching. The hydroxyls density was found to play a major role in strong adhesion prevailing over surface roughness, contact area, oxide thickness and hydrophobicity. Despite the efficient performance of hydrogen bonds from acid and alkaline etching on aluminum, these connections do not yield sufficiently stable bonds that make an impermeable barrier of epoxy coatings on steel. Covalent bonds (Me-O-Si) represent the key to achieve a significant improvement in mechanical and chemical resistance against the ingress of water and polymer chain relaxation. This makes the sol-gel primer a simple, economical, and environmentally alternative towards efficient bonding at a molecular level., Financial support from the European Union´s Horizon 2020 Research and Innovation Programme under grant agreement No 739566, project FunGlass. Additionally, the funding obtained from VEGA 1/0171/21 and VEGA 1/0241/23 is acknowledged. This article is also part of the dissemination activities of MICINN project TED2021-131258B-I00., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Improved corrosion resistance of AZ31B Mg alloy by eco-friendly flash-PEO coatings

  • Merino, Emilia
  • Chandrasekar, A.R.
  • Pakseresht, A.
  • Mohedano, M.
  • Durán, Alicia
  • Castro Martín, Yolanda
The aim of this work was the preparation of an environmentally friendly protective coating on the AZ31B alloy using Flash plasma electrolytic oxidation (F-PEO) process. It was developed with different electrolyte compositions, that determine the morphology and properties of the coatings, this being crucial to understand the anti-corrosion properties. The incorporation of carbonate ions to the electrolyte proved to enhance the electrical response of the F-PEO process, resulting in a more efficient process with an energy reduced consumption of 1.1 kW h m−2μm−1. Surface and cross-sectional morphology analysis of the coatings revealed the presence of isolated pores structure with small pore size (less than 1 µm) that delays the infiltration of aggressive ions towards the substrate. The characterisation by XRD, EDX and Raman spectroscopy showed the presence of amorphous carbonate and phosphate phases in the FPEO-CO layer, that provide a self-restauration effect through a dissolution/reprecipitation mechanism. The lowest value of the corrosion current density was obtained for FPEO-CO coating, 4.60 × 10−7 A·cm−2, together with the highest impedance modulus (f<0.1 Hz), ⁓104 Ω·cm2, two orders of magnitude higher than the AZ31B Mg alloy. Furthermore, the corrosion protection properties of FPEO-CO coating were also analysed through an immersion test in 3.5 wt.% NaCl, confirming the excellent response of the coating for long times up to 336 h (2 weeks). The synergy between a more compact coating and the self-repairing ability of carbonate amorphous species plays a critical role in improving the corrosion resistance properties of the AZ31B Mg alloy, offering an eco-friendly alternative to chromate conversion coatings. © 2024 The Author(s), This article is a part of the dissemination activities of MICINN project TED2021-131258B-I00, and the project FunGlass, which has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement No 739566. M., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Novel self-healing glass-like CexOY film on a Flash-PEO coated AZ31B Mg alloy

  • Merino, Emilia
  • Cere, S.
  • Durán, Alicia
  • Castro Martín, Yolanda
The aim of this work is to develop a glass-like CexOy coating to seal the pores of a Flash-PEO coated AZ31B Mg alloy and simultaneously provide smart self-healing corrosion protection. The cerium sol was synthesized using cerium acetate as main precursor by sol-gel method. SEM micrographs revealed that upon cerium sol deposition, the pores of the oxide coating were effectively sealed, resulting in a double-layer coating system and thereby in a big reservoir of cerium ions (Ce3+/Ce4+). The glassy character of the cerium coating, confirmed by X-Ray diffraction, implies that cerium exists in Ce3+ and Ce4+ ionic states enclosed in a high internal energy structure which facilitate the diffusion of cerium ions to active cathodic zone. Electrochemical Impedance Spectroscopy (EIS), X-Ray Diffraction (XRD), and Raman spectroscopy were used to explore the active corrosion protection of the CexOy sol-gel coating. The corrosion inhibition mechanism involves the migration of cerium ions and the precipitation of insoluble-crystalline cerium compounds (CeO2). The coating demonstrated self-healing properties, presenting a promising alternative to traditional chrome conversion coatings (CCC). © 2024, This article is a part of the dissemination activities of MICINN project TED2021-131258B-I00, and the project FunGlass, which has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement No 739566., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Tesis doctoral (DoctoralThesis)

Sistema integrado de recubrimientos anticorrosivos con efecto auto-curado para aleaciones ligeras combinando el proceso de anodizado y el proceso Sol-Gel: procesamiento y caracterización

  • Merino, Emilia
Tesis Doctoral inédita leída en la Universidad Autónoma de Madrid, Facultad de Ciencias, Departamento de Químia Física Aplicada. Fecha de Lectura: 12-03-2024 Esta Tesis tiene embargado el acceso al texto completo hasta el 12-09-2025, El trabajo de investigación de la presente tesis doctoral se ha llevado a cabo en el marco del proyecto Europeo “Centre for funcional and Surface-functionalized glasses” (FunGlass) No739566 y es parte de las actividades de diseminación del proyecto MICINN TED2021-131258B-I00, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of the BF3·O(C2H5)2 on the corrosion resistance of hybrid silica sol-gel coatings deposited on flash-PEO-treated Mg alloy

  • Merino, Emilia
  • Cere, S.
  • Ozcan, O.
  • Dimper, M.
  • Sobrados, Isabel
  • Durán, Alicia
  • Castro Martín, Yolanda
Achieving highly cross-linked sol-gel coatings to provide effective corrosion protection of Mg alloys remains a challenging task. The aim of this work is to evaluate the effect boron trifluoride diethyl etherate (BF3·O(C2H5)2) as catalyst to epoxy group in a GPTMS/TEOS/SiO2 sol and assesses its effect on the structure and corrosion resistance properties of Flash-PEO coated pre-treated Mg alloy. 29Si MAS NMR and 13C CPMAS-NMR demonstrated that (BF3·O(C2H5)2) efficiently promotes the epoxy polymerization of the GPTMS and the formation of a hybrid silica network. However, the amount of (BF3·O(C2H5)2) should be optimized to minimize the formation of undesirable byproducts such as ethyl ether terminal units. Therefore, GPTMS/TEOS/SiO2 sols containing different amounts of (BF3·O(C2H5)2) were synthesized and deposited onto the Flash-PEO coated Mg alloy, leading to bilayer systems with a total thickness of ⁓8 μm. The corrosion behavior of the bilayer coatings in 3.5 wt% NaCl solution was evaluated by electrochemical impedance spectroscopy (EIS) and Scanning Kelvin probe microscope (SKPFM). The results revealed that the barrier properties of the coatings with enhanced cross-linked structure showed impedance modulus (│Z│f:0.1 Hz) approximately four orders of magnitude higher than the bare magnesium alloy and two orders of magnitude higher than the F-PEO coated sample. A suitable compromise between (BF3·O(C2H5)2) amount and sol-gel film structure is required to obtain a more durable barrier coating capable to extend the protective lifespan of the magnesium alloy. © 2025 Elsevier B.V., This project is part of dissemination activities of the MICINN project TED2021-131258B-I00. Funding from HORIZON-EIC-2023-PATHFIN DEROPEN-01-Proposal number 101129967-Everglass is acknowledged, Peer reviewed