Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 17
Encontrada(s) 1 página(s)

Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Wearable, battery-free, wireless multiplexed printed sensors for heat stroke prevention with mussel-inspired bio-adhesive membranes

  • Maroli, Gabriel|||0000-0001-8921-4205
  • Rosati, Giulio|||0000-0002-0227-4561
  • Suárez García, Salvio|||0000-0002-4156-0579
  • Bedmar-Romero, Daniel
  • Kobrin, Robert
  • González-Laredo, Álvaro
  • Urban, Massimo|||0000-0001-6083-833X
  • Álvarez Diduk, Ruslan|||0000-0002-9876-1574
  • Ruiz-Molina, Daniel|||0000-0002-6844-8421
  • Merkoçi, Arben|||0000-0003-2486-8085
Wearable technologies are becoming pervasive in our society, and their development continues to accelerate the untapped potential of continuous and ubiquitous sensing, coupled with big data analysis and interpretation, has only just begun to unfold. However, existing wearable devices are still bulky (mainly due to batteries and electronics) and have suboptimal skin contact. In this work, we propose a novel approach based on a sensor network produced through inkjet printing of nanofunctional inks onto a semipermeable substrate. This network enables real-time monitoring of critical physiological parameters, including temperature, humidity, and muscle contraction. Remarkably, our system operates under battery-free and wireless near-field communication (NFC) technology for data readout via smartphones. Moreover, two of the three sensors were integrated onto a naturally adhesive bioinspired membrane. This membrane, developed using an eco-friendly, high-throughput process, draws inspiration from the remarkable adhesive properties of mussel-inspired molecules. The resulting ultra-conformable membrane adheres effortlessly to the skin, ensuring reliable and continuous data collection. The urgency of effective monitoring systems cannot be overstated, especially in the context of rising heat stroke incidents attributed to climate change and high-risk occupations. Heat stroke manifests as elevated skin temperature, lack of sweating, and seizures. Swift intervention is crucial to prevent progression to coma or fatality. Therefore, our proposed system holds immense promise for the monitoring of these parameters on the field, benefiting both the general population and high-risk workers, such as firefighters.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Introducing all-inkjet-printed microneedles for in-vivo biosensing

  • Rosati, Giulio|||0000-0002-0227-4561
  • Deroco, Patricia Batista
  • Bonando, Matheus Guitti
  • Dalkiranis, Gustavo G.
  • Cordero Edwards, Kumara|||0000-0003-3721-7863
  • Maroli, Gabriel|||0000-0001-8921-4205
  • Kubota, Lauro Tatsuo
  • Oliveira, Osvaldo N.|||0000-0002-5399-5860
  • Saito, Lúcia Akemi Miyazato
  • De Carvalho Castro Silva, Cecilia|||0000-0003-3933-1838
  • Merkoçi, Arben|||0000-0003-2486-8085
Microneedles are mainly used for pain-free drug administration and in biosensing for wearable systems. They are also promising for fields such as agronomy for precision farming, but their fabrication is not straightforward, often requiring expensive equipment and cleanroom protocols, being unsuitable for mass production. Here, we report a new and simple method for the scalable fabrication of all-inkjet-printed conductive microneedles based on silver nanoparticles (extensible to any other metallic nanoparticle ink) and a simple example of their application for monitoring the electrochemical properties of plants.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Unleashing inkjet-printed nanostructured electrodes and battery-free potentiostat for the DNA-based multiplexed detection of SARS-CoV-2 genes

  • Rossetti, Marianna
  • Srisomwat, Chawin
  • Urban, Massimo
  • Rosati, Giulio
  • Maroli, Gabriel
  • Yaman Akbay, Hatice Gödze
  • Chailapakul, Orawon
  • Merkoçi, Arben
Following the global COVID-19 pandemic triggered by SARS-CoV-2, the need for rapid, specific and cost-effective point-of-care diagnostic solutions remains paramount. Even though COVID-19 is no longer a public health emergency, the disease still poses a global threat leading to deaths, and it continues to change with the risk of new variants emerging causing a new surge in cases and deaths. Here, we address the urgent need for rapid, cost-effective and point-of-care diagnostic solutions for SARS-CoV-2. We propose a multiplexed DNA-based sensing platform that utilizes inkjet-printed nanostructured gold electrodes and an inkjet-printed battery-free near-field communication (NFC) potentiostat for the simultaneous quantitative detection of two SARS-CoV-2 genes, the ORF1ab and the N gene. The detection strategy based on the formation of an RNA-DNA sandwich structure leads to a highly specific electrochemical output. The inkjet-printed nanostructured gold electrodes providing a large surface area enable efficient binding and increase the sensitivity. The inkjet-printed battery-free NFC potentiostat enables rapid measurements and real-time data analysis via a smartphone application, making the platform accessible and portable. With the advantages of speed (5 min), simplicity, sensitivity (low pM range, ∼450% signal gain) and cost-effectiveness, the proposed platform is a promising alternative for point-of-care diagnostics and high-throughput analysis that complements the COVID-19 diagnostic toolkit., ICN2 is funded by CERCA programme, Generalitat de Catalunya. Grant SEV-2017-0706 funded by MCIN/AEI/10.13039/501100011033. This project was in part supported from the European Union's Horizon 2020 research and innovation programme under grant agreement No 101008701 (Project EMERGE), from PID2021-124795NB-I00 funded by MCIN/AEI/10.13039/501100011033 and from “ERDF A way of making Europe”. M.R. is supported from the European Union's Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie grant agreement No 101029884 (SERENA). Views and opinions expressed are however those of the authors only and do not necessarily reflect those of the European Union. The European Union can not be held responsible for them. M.U. has carried out the work within the framework of the doctoral program ‘Doctorado en Biotecnología’ from the Universitat Autònoma de Barcelona. G.M. would like to express his gratitude to the Carolina Foundation for financial support through the scholarship “Doctorado 2020.” G.M. acknowledges Universitat Autonoma de Barcelona (UAB) for the possibility of performing this work inside the framework of Chemistry PhD Programme. C.S. and O.C. would like to thank the National Research Council of Thailand (NRCT) through the Royal Golden Jubilee Ph.D. program (grant number PHD/0016/2561) and the Distinguished Research Professor Grant, the National Research Council of Thailand (NRCT) through the grant number N41A640073., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nanostructure tuning of gold nanoparticles films via click sintering

  • Urban, Massimo
  • Rosati, Giulio
  • Maroli, Gabriel
  • Della Pelle, Flavio
  • Bonini, Andrea
  • Sajti, Laszlo
  • Fedel, Mariangela
  • Merkoçi, Arben
Colloidal metal nanoparticles dispersions are commonly used to create functional printed electronic devices and they typically require time-, energy- and equipment-consuming post-treatments to improve their electrical and mechanical properties. Traditional methods, e.g. thermal, UV/IR, and microwave treatments, limit the substrate options and may require expensive equipment, not available in all the laboratories. Moreover, these processes also cause the collapse of the film (nano)pores and interstices, limiting or impeding its nanostructuration. Finding a simple approach to obtain complex nanostructured materials with minimal post-treatments remains a challenge. In this study, a new sintering method for gold nanoparticle inks that called as “click sintering” has been reported. The method uses a catalytic reaction to enhance and tune the nanostructuration of the film while sintering the metallic nanoparticles, without requiring any cumbersome post-treatment. This results in a conductive and electroactive nanoporous thin film, whose properties can be tuned by the conditions of the reaction, i.e., concentration of the reagent and time. Therefore, this study presents a novel and innovative one-step approach to simultaneously sinter gold nanoparticles films and create functional nanostructures, directly and easily, introducing a new concept of real-time treatment with possible applications in the fields of flexible electronics, biosensing, energy, and catalysis., The ICN2 is funded by the CERCA programme/Generalitat de Catalunya. The ICN2 is supported by the Severo Ochoa Centres of Excellence programme, Grant CEX2021-001214-S, funded by MCIN/AEI/10.13039.501100011033. This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 101008701. Views and opinions expressed were however those of the author(s) only and did not necessarily reflect those of the European Union. The European Union could not be held responsible for them. PID2021-124795NB-I00 funded by MCIN/AEI/ 10.13039/501100011033 and by “ERDF A way of making Europe”. This work has been carried out within the framework of the doctoral program ‘Doctorado en Biotecnologia’ from the Universitat Autonoma de Barcelona. G.M. acknowledges the Fundación Carolina for the Doctoral Scholarship granted under the program “Doctorado 2020”. F.D.P. acknowledge the Ministry of Education, University and Research (MIUR) and European Social Fund (ESF) for the PON R&I 2014–2020 program, action 1.2 “AIM: Attraction and International Mobility” (AIM1894039-3). A.B. is supported by the ERASMUS+ mobility program during the doctoral school in Chemistry and Material Science (DSCM) at the Department of Chemistry and Industrial Chemistry, University of Pisa (UNIPI), Italy., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2021-001214-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Direct writing of graphene electrodes for point-of-care electrochemical sensing applications

  • Zhao, Lei
  • Piper, Andrew
  • Rosati, Giulio
  • Merkoçi, Arben
Electrochemical sensors are increasingly garnering attention as valuable tools for point-of-care (POC) testing due to their low costs, high sensitivities, and ease of miniaturization. Graphene-based materials, renowned for their tunable electrical conductivity, high specific surface areas, versatile functionality, and biocompatibility; are highly suited for the fabrication of electrochemical sensors with heightened sensitivities. Non-contact, maskless, direct writing methods allow the rapid, large-scale production of graphene electrodes with high design flexibility. Researchers globally are advancing graphene electrode production, aiming for smaller, faster, and more efficient sensors. This review provides a comprehensive overview of recent advances on the direct writing of graphene electrodes for electrochemical sensing applications. It covers the basics of direct writing techniques, the advancements in graphene ink/precursor preparation, structural design, and device integration, with a focus on POC platforms., ICN2 is funded by CERCA programme, Generalitat de Catalunya. The ICN2 is supported by the Severo Ochoa Centres of Excellence programme, Grant CEX2021-001214-S, funded by MCIU/AEI/10.13039.501100011033. We acknowledge Departament de Recerca i Universitats of Generalitat de Catalunya for the grant 2021 SGR 01464 and Grant PID2021-124795NB-I00 funded by MCIN/AEI/ 10.13039/501100011033 and by “ERDF A way of making Europe. Lei Zhao acknowledge the financial support from China Scholarship Council (CSC) and the Fundamental Research Funds for the Central Universities. This project has received funding from the EMERGE project, European Union's Horizon 2020 research and innovation programme, under Grant Agreement No. 101008701. Views and opinions expressed are however those of the author(s) only and do not necessarily reflect those of the European Union., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2021-001214-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Introducing all-inkjet-printed microneedles for in-vivo biosensing

  • Rosati, Giulio
  • Batista Deroco, Patricia
  • Guitti Bonando, Matheus
  • Dalkiranis, Gustavo G.
  • Cordero-Edwards, Kumara
  • Maroli, Gabriel
  • Tatsuo Kubota, Lauro
  • Oliveira Jr., Osvaldo N.
  • Saito, Lúcia A. M.
  • Castro Silva, Cecilia de Carvalho
  • Merkoçi, Arben
Microneedles are mainly used for pain-free drug administration and in biosensing for wearable systems. They are also promising for fields such as agronomy for precision farming, but their fabrication is not straightforward, often requiring expensive equipment and cleanroom protocols, being unsuitable for mass production. Here, we report a new and simple method for the scalable fabrication of all-inkjet-printed conductive microneedles based on silver nanoparticles (extensible to any other metallic nanoparticle ink) and a simple example of their application for monitoring the electrochemical properties of plants., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature., The ICN2 is funded by the CERCA programme / Generalitat de Catalunya. The ICN2 is funded by the CERCA programme / Generalitat de Catalunya. The ICN2 is supported by the Severo Ochoa Centres of Excellence programme, Grant CEX2021-001214-S, funded by MCIU/AEI/10.13039.501100011033. We acknowledge Departament de Recerca i Universitats of Generalitat de Catalunya for the grant 2021 SGR 01464. MIaSkin project funded by the ICN2 Severo Ochoa Seed Funding for Emerging Topics 2021 Program. We acknowledge Grant PLEC2021-007727 funded by MCIN/AEI/ 10.13039/501100011033 and the “European Union NextGenerationEU/PRTR”. This project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 101008701 (EMERGE project). Views and opinions expressed are however those of the author(s) only and do not necessarily reflect those of the European Union. The European Union can not be held responsible for them. P.B.D and L.T.K acknowledge Sao Paulo Research Foundation (FAPESP, Brazil) grant numbers 2021/14732-0, 2014/50867-3 and 2019/00166-2. G.G.D. and O.N.O. acknowledge Sao Paulo Research Foundation (FAPESP, Brazil) grant numbers 2018/22214–6, 2019/26375-7, 2021/12458-8. M.G.B., C.C.C.S and L.A.M.S. are grateful to financial support from MackPesquisa, CAPES PrInt project no. 88887.310281/2018-00 and CNPq MAI/DAI 2020 and CNPq 313091/2022-6. G.M. would like to express his gratitude to the Carolina Foundation for financial support through the scholarship “Doctorate 2020.” G.M. Acknowledges Universitat Autonoma de Barcelona (UAB) for the possibility of performing this work within the framework of Chemistry PhD Programme., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2021-001214-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Low-cost inkjet-printed nanostructured biosensor based on CRISPR/Cas12a system for pathogen detection

  • Carota, Angela Gilda
  • Bonini, Andrea
  • Urban, Massimo
  • Poma, Noemi
  • Vivaldi, Federico M.
  • Tavanti, Arianna
  • Rossetti, Marianna
  • Rosati, Giulio
  • Merkoçi, Arben
  • Di Francesco, Fabio
The escalating global incidence of infectious diseases caused by pathogenic bacteria, especially in developing countries, emphasises the urgent need for rapid and portable pathogen detection devices. This study introduces a sensitive and specific electrochemical biosensing platform utilising cost-effective electrodes fabricated by inkjet-printing gold and silver nanoparticles on a plastic substrate. The biosensor exploits the CRISPR/Cas12a system for detecting a specific DNA sequence selected from the genome of the target pathogen. Upon detection, the trans-activity of Cas12a/gRNA is triggered, leading to the cleavage of rationally designed single-strand DNA reporters (linear and hairpin) labelled with methylene blue (ssDNA-MB) and bound to the electrode surface. In principle, this sensing mechanism can be adapted to any bacterium by choosing a proper guide RNA to target a specific sequence of its DNA. The biosensor's performance was assessed for two representative pathogens (a Gram-negative, Escherichia coli, and a Gram-positive, Staphylococcus aureus), and results obtained with inkjet-printed gold electrodes were compared with those obtained by commercial screen-printed gold electrodes. Our results show that the use of inkjet-printed nanostructured gold electrodes, which provide a large surface area, in combination with the use of hairpin reporters containing a poly-T loop can increase the sensitivity of the assay corresponding to a signal variation of 86%. DNA targets amplified from various clinically isolated bacteria, have been tested and demonstrate the potential of the proposed platform for point-of-need applications., A.G.C. acknowledges the University of Pisa and the doctoral scholarship in memory of Giulio Regeni. A.B. was supported by the project CRISPRSENSE funded by Tuscany region, Italy (“DECRT. DIRIG. n. 21607 of 29-11-2021”). F.D.F. acknowledges the INSTM three-year project 2021-2024 “Sviluppo di sensori per la misura dell'attività proteasica e l'identificazione di batteri”. The work at ICN2 and the fabrication of the devices was partially funded by project EMERGE. This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 101008701. Views and opinions expressed are however those of the author(s) only and do not necessarily reflect those of the European Union. The European Union can not be held responsible for them. The development of the device fabrication platforms has been partially funded through the MICROB-PREDICT project. The MICROB-PREDICT project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 825694. This reflects only the author's view, and the European Commission is not responsible for any use that may be made of the information it contains. The ICN2 is funded by the CERCA programme/Generalitat de Catalunya. The ICN2 is supported by the Severo Ochoa Centres of Excellence programme, Grant CEX 2021-001214-S, funded by MCIN/AEI/10.13039.501100011033. M.R. is supported by the European Union's Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie grant agreement No 101029884 (SERENA). We acknowledge Departament de Recerca i Universitats of Generalitat de Catalunya for the grant 2021 SGR 01464., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2021-001214-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Wearable, battery-free, wireless multiplexed printed sensors for heat stroke prevention with mussel-inspired bio-adhesive membranes

  • Maroli, Gabriel
  • Rosati, Giulio
  • Suárez-García, Salvio
  • Bedmar-Romero, Daniel
  • Kobrin, Robert
  • González-Laredo, Álvaro
  • Urban, Massimo
  • Álvarez-Diduk, Ruslan
  • Ruiz Molina, Daniel
  • Merkoçi, Arben
Wearable technologies are becoming pervasive in our society, and their development continues to accelerate the untapped potential of continuous and ubiquitous sensing, coupled with big data analysis and interpretation, has only just begun to unfold. However, existing wearable devices are still bulky (mainly due to batteries and electronics) and have suboptimal skin contact. In this work, we propose a novel approach based on a sensor network produced through inkjet printing of nanofunctional inks onto a semipermeable substrate. This network enables real-time monitoring of critical physiological parameters, including temperature, humidity, and muscle contraction. Remarkably, our system operates under battery-free and wireless near-field communication (NFC) technology for data readout via smartphones. Moreover, two of the three sensors were integrated onto a naturally adhesive bioinspired membrane. This membrane, developed using an eco-friendly, high-throughput process, draws inspiration from the remarkable adhesive properties of mussel-inspired molecules. The resulting ultra-conformable membrane adheres effortlessly to the skin, ensuring reliable and continuous data collection. The urgency of effective monitoring systems cannot be overstated, especially in the context of rising heat stroke incidents attributed to climate change and high-risk occupations. Heat stroke manifests as elevated skin temperature, lack of sweating, and seizures. Swift intervention is crucial to prevent progression to coma or fatality. Therefore, our proposed system holds immense promise for the monitoring of these parameters on the field, benefiting both the general population and high-risk workers, such as firefighters., The ICN2 is funded by the CERCA programme/Generalitat de Catalunya. The ICN2 has been supported by the Severo Ochoa Centres of Excellence programme [SEV-2017-0706] and is currently supported by the Severo Ochoa Centres of Excellence programme, Grant CEX2021-001214-S, both funded by MICIU/AEI/10.13039/501100011033. The MIaSkin project has been funded by the ICN2 Severo Ochoa Seed Funding for Emerging Topics 2021 Program. This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 101008701. Views and opinions expressed are however those of the author(s) only and do not necessarily reflect those of the European Union. The European Union can not be held responsible for them. We acknowledge Departament de Recerca i Universitats of Generalitat de Catalunya for the grant 2021 SGR 01464. This work was supported by grantsPID2021-124795NB-I00 and PID2021-127983OB-C21 financed by MICIU/AEI/10.13039/501100011033 and ERDF “A way to make Europe”. G.M. would like to express his gratitude to the Carolina Foundation for financial support through the scholarship “Doctorado 2020”. G.M. acknowledges Universitat Autonoma de Barcelona (UAB) for the possibility of performing this work inside the framework of Chemistry PhD Programme. G.M. thanks Patricia Batista Deroco and Lei Zaho for their advice on the Dimatix printer. G.M. thanks Nerea de Mariscal i Molinas for her help in filming the S.I. video., With funding from the Spanish government through the "Severo Ochoa Centre of Excelence" accreditation (SEV-2017-0706), With funding from the Spanish government through the "Severo Ochoa Centre of Excelence" accreditation (CEX2021-001214-S), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Water-based graphene oxide inks for inkjet-printed flexible moisture energy generators

  • Anagnostou, Katerina
  • Urban, Massimo
  • Sotiropoulos, Evangelos
  • Polyzoidis, Christos
  • Kavalieraki, Katerina
  • Mouratis, Kyriakos
  • Rosati, Giulio
  • Merkoçi, Arben
  • Rogdakis, Konstantinos
  • Kymakis, E.
With the need for clean sustainable energy and low-waste practices rising, battery-free technologies that run on renewable ambient energy sources are an attractive solution to these environmental concerns. Herein, Graphene oxide (GO) and GO-PEDOT: PSS water-based inks were formulated from inexpensive precursor materials following user-friendly, up-scalable methods. GO-based moisture-active films were deposited on flexible lightweight substrates using inkjet printing to fabricate Moisture Energy Generators (MEG), devices that convert ambient moisture energy variation into a voltage output. The performance of the fabricated MEGs was evaluated using a custom-made automated humidity chamber, yielding an average voltage output of Vo=183 (± 1.76) mV for pure GO and Vo=194 (± 0.97) mV for GO-PEDOT: PSS, in the relative humidity range of 45-95%. We support that this study may provide fertile ground for the development of low-cost energy harvesters for self-powered portable and wearable technologies, minimising the need for batteries and reducing electronic waste., The authors would like to acknowledge the following contributors: For the ATR-IR and Raman spectroscopy measurements, Klytaimnistra Katsara (Department of Agriculture, Hellenic Mediterranean University, Institute of Electronic Structure and Laser, Foundation for Research and Technology—Hellas, (FORTH), GreeceFor the XPS measurements, Emmanuel I. Spanakis (Department of Materials Science and Engineering, University of Crete, Greece)For the XPS analysis, Dimitris Tsikritzis (Department of Electrical & Computer Engineering, Hellenic Mediterranean University, Greece)For the realisation of the bending and angle measurement setup, Angelos Mastrokostas, Lazaros Anthymidis, Antonios Arvanitis (Department of Electrical & Computer Engineering, Hellenic Mediterranean University, Greece)The work has been supported by the European Union’s Horizon 2020 research and Innovation program under project EMERGE. The EMERGE project has received funding under Grant Agreement No. 101008701. The authors acknowledge the Departament de Recerca i Universitats of Generalitat de Catalunya for the grant 2021 SGR 01464., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Prussian-Blue Catalysis and NFC Synergy: a Battery-Free Laser-Induced Graphene-Based Platform for Urine Glucose Monitoring at Point-of-Care

  • Uzunçar, Sinan
  • Maroli, Gabriel
  • Urban, Massimo
  • Merkoçi, Arben
Prussian-blue nanoparticles (PBNPs) show promise in electrochemical hydrogen peroxide (H2O2) sensing but face operational stability challenges without complex strategies. This study introduces a simplified, polymer-based synthesis method, enhancing their stability in a single step. Chemical polymerization of Prussian-blue (PB) and poly(3,4-ethylenedioxythiophene) (PEDOT) with gelatin as a polycationic soft template yields a self-assembled PB-infused Catalytic Hetero-interface Architecture (PB-CHIA) that remarkably improves the stability of PBNPs and offers functional groups for enzyme immobilization, supporting robust biosensing applications. The softened PEDOT rigidity extends PB-CHIA's applicability to various carbonaceous electrode substrates, including glassy carbon and laser-induced graphene (LIG) via simple drop-casting. A fluidic cell module designed with the optimized LIG morphology (nano-fibrous fringes, LIG-F, diameter: 72.87 ± 12.24 nm) modified with PB-CHIA and glucose oxidase enables non-invasive urine glucose monitoring. The configuration accurately quantifies glucose within a linear range of 10-400 µM [R2: 0.991, Sensitivity: 29.88 ± 4.98 µA mM⁻¹ cm⁻2, Detection Limit: 4.52 ± 2.24 µM], covering medical needs. A near-field communication potentiostat is devised for a fully integrated, batteryless, wireless point-of-care (POC) prototype, enabling rapid smartphone readouts in 15 s for daily home-based use. The stable operation of PB-CHIA allows working electrodes' scalable production, highlighting its potential for diverse POC devices in urinary analysis reliant on H2O2 assays., The ICN2 was funded by the CERCA program/Generalitat de Catalunya. The ICN2 has been supported by the Severo Ochoa Centres of Excellence program [SEV-2017-0706] and is currently supported by the Severo Ochoa Centres of Excellence program, Grant CEX2021-001214-S, both funded by MCIN and MCIU/AEI/10.13039.501100011033″. This project was in part supported by the European Union's Horizon 2020 research and innovation program under grant agreement No 101008701 (Project EMERGE) and Grant PID2021-124795NB-I00 funded by MICIU/AEI/10.13039/501100011033 and by “ERDF/EU”. The authors acknowledge the Department de Recerca i Universitats of Generalitat de Catalunya for the grant 2021 SGR 01464. S.U. thanks TUBITAK for financial support through the 2219 International Postdoctoral Research Fellowship Program (1059B192100540). G.M. would like to express his gratitude to the Carolina Foundation for financial support through the scholarship “Doctorado 2020.” G.M. acknowledges Universitat Autonoma de Barcelona (UAB) for the possibility of performing this work inside the framework of the Chemistry PhD Program. M.U. has carried out the work within the framework of the doctoral program “Doctorado en Biotecnología” from the Universitat Autònoma de Barcelona. Funding for open access charge: TUBITAK-ULAKBIM, Turkiye, With funding from the Spanish government through the "Severo Ochoa Centre of Excelence" accreditation (CEX2021-001214-S), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Laser-Induced Graphene: A Promising Conductive Platform for Cell Culture

  • Vazão de Almeida, Henrique
  • Inácio, José Manuel
  • Pereira, Cláudia
  • Pinheiro, Tomás
  • Calmeiro, Tomás
  • Correia, Ricardo
  • Coelho, João
  • Pinto, Joana Vaz
  • Belo, José António
  • Martins, Rodrigo
  • Fortunato, Elvira
Cardiovascular mortality remains a major health challenge. Cardiomyocyte (CM)-based tissue engineering (TE) offers promising alternatives for developing therapies via in vitro models. However, the immature phenotype of CM in engineered tissues hampers progress. Recent studies introduce conductive materials like graphene to enhance CM maturation, but conventional graphene synthesis suffers from complexity, toxicity, and low yield. Laser-induced graphene (LIG) provides a sustainable, cost-effective, eco-friendly solution with efficient conductivity and biocompatibility. A LIG-based substrate is bioengineered in this study, hypothesizing that its conductive, anisotropic properties promote CM maturation and mimic the native cardiac niche. LIG is fabricated using a CO2 laser with Parylene-C as a precursor. Stem cells (SCs) and SC-derived embryoid bodies (EBs) are cultured on LIG substrates, and their viability, metabolic activity, morphology, and protein expression are evaluated through immunofluorescence and electron microscopy. Both SCs and EBs maintain viability and activity throughout the culture. Moreover, EB-derived CM exhibit spontaneous contraction and express cardiac-specific proteins, confirming functional differentiation on LIG matrices. This first report demonstrates that LIG substrates support SC culture and differentiation, highlighting their potential in developing refined in vitro cardiac models and advancing regenerative therapeutic strategies. The findings support LIG as a transformative advancement in TE., The authors want to thank all NOVA Medical School facilities. FEDER funds partially financed this work through the COMPETE 2020 Programme and National funds from FCT – Fundação para a Ciência e a Tecnologia, IP, in the scope of projects LA/P/0037/2020, UIDP/50025/2020 and UIDB/50025/2020 of the Associate Laboratory Institute of Nanostructures, Nanomodeling and Nanofabrication – i3N and project LIGHEART (2022.08597.PTDC), Scientific Employment Stimulus to H.V.A (2020.01194.CEECIND), Scientific Employment Stimulus to J.M.I. (Norma Transitória 8189/2018), iNOVA4Health-UID/Multi/04462/2020 and LS4FUTURE Associated Laboratory (LA/P/0087/2020). European Union's Horizon 2020 Research and Innovation Programme under Grant Agreement number 101008701 (EMERGE, H2020-INFRAIA-2020-1) also partially supported this work. Also, this work was supported by two PRR projects: Pacto Bioeconomia Azul (C644915664-00000026) and From Fossil to Forrest (C644920945-00000036)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nanomaterial-Based Inkjet Printing for Electrochemical Sensing

  • Panáček, David
  • Urban, Massimo
  • Silvestri, Alessandro
  • Dědek, Ivan
  • Nalepa, Martin Alex
  • Merkoçi, Arben
  • Prato, Maurizio
  • Otyepka, Michal
Inkjet printing (IJP) has emerged as a transformative technology for printed and flexible electronics, redefining electrode engineering for (bio)chemical sensing. It enables maskless, picoliter-scale, additive deposition with high spatial precision, uniformity, and material efficiency. We provide a comprehensive overview of IJP as both a fabrication and post-fabrication functionalization platform for electrochemical working electrodes and fully printed devices. We integrate advances in ink formulation, jetting behavior, and substrate interactions with performance metrics such as layer thickness, roughness, electrochemical surface area, sensitivity, detection limit, and reproducibility. Comparative analyses with drop-casting and screen-printing highlight IJP's advantages in reproducibility, scalability, and material economy. Particular emphasis is placed on nanomaterial- and bioink-based systems, including carbon nanomaterials, MXenes, and hybrid inks, where controlled deposition governs electrode functionality. We also discuss emerging opportunities in hybrid architectures, reactive printing, and sustainable approaches using biodegradable substrates and water-based inks. Finally, we outline a roadmap toward automated, digitally controlled, and environmentally responsible manufacturing of customizable sensors for wearable, biomedical, food, and environmental applications. Collectively, these developments position inkjet printing as an enabling framework for the next generation of intelligent, reproducible, and sustainable sensing technologies., The work was supported by ERDF/ESF project TECHSCALE (No. CZ.02.01.01/00/22_008/0004587) and ERDF/ESF project “Interdisciplinary Approaches to the Prevention and Diagnosis of Viral Diseases” (CZ.02.01.01/00/23_021/0008856). M.O. and D.P. also acknowledge financial support of the European Union under the REFRESH—Research Excellence For Region Sustainability and High-tech Industries project number CZ.10.03.01/00/22_003/0000048 via the Operational Programme Just Transition. M.P. is the AXA Chair for Bionanotechnology (2016−2026). A.S. acknowledges the financial support of Ca’ Foscari University of Venice. The ICN2 is funded by the CERCA programme / Generalitat de Catalunya. The ICN2 is supported by the Severo Ochoa Centres of Excellence programme, Grant CEX2021-001214-S, funded by MCIU/AEI/10.13039.501100011033. This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 101008701. Views and opinions expressed are however those of the author(s) only and do not necessarily reflect those of the European Union. The European Union cannot be held responsible for them., Open access publishing facilitated by Vysoka skola banska-Technicka univerzita Ostrava, as part of the Wiley - CzechELib agreement., With funding from the Spanish government through the "Severo Ochoa Centre of Excelence" accreditation (CEX2021-001214-S), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Fully-printed microneedles meet plants: a pathway towards easy-to-use NFC monitoring of total ionic conductivity in precision agriculture

  • Baraniecki, Dominik
  • Rosati, Giulio
  • Miarka, Amelia
  • Krzeminski, Jakub
  • Martínez-Domingo, Carmen
  • Jakubowska, Malgorzata
  • Ramón, Eloi
  • Merkoçi, Arben
This study showcases and validates a fully-printed, low-cost microneedles (MNs) device integrated with environmental sensors and NFC wireless readout for real-time monitoring of changes in plant total ionic conductivity. The Aerosol-Jet printed MNs patch enabled minimally invasive impedance measurements for the monitoring of leaf hydration and ion uptake. Inkjet-printed temperature and humidity sensors provided complementary environmental and leaf's microclimate data. Both sensing platforms were integrated in a cost-effective, easy-to-use wooden clip assembly, granting adhesion and reproducible MNs insertion. Dehydration and ions uptake tests demonstrated that the devices can detect ionic variations in different cellular compartments of the leaves, with distinct responses across plant species reflecting their physiological and anatomical differences. The NFC system validation confirmed that wireless, battery-free readout can be used to observe similar impedance trends with respect to the ones observed with conventional potentiostat measurements. Overall, the presented platform establishes a scalable approach toward simple, field-deployable plant monitoring systems, supporting future development of species-tailored and functionally enhanced sensors for precision agriculture., The ICN2 is funded by the CERCA programme/Generalitat de Catalunya. The ICN2 is supported by the Severo Ochoa Centres of Excellence programme, Grant CEX2021-001214-S, funded by MCIU/AEI/10.13039.501100011033. The work has been supported by the European Union's Horizon 2020 research and Innovation program under project EMERGE. The EMERGE project has received funding under Grant Agreement No. 101008701. We acknowledge Departament de Recerca i Universitats of Generalitat de Catalunya for the grant 2021 SGR 01464. We acknowledge Grant PLEC2021-007727 funded by MCIN/AEI/10.13039/501100011033 and the “European Union NextGenerationEU/PRTR”. We acknowledge the contributions of the intern at CEZAMAT WUT – Katarzyna Ratajczyk, MSc – in manufacturing the prototypes as well as the electrochemical and mechanical characterization. We thank Katarzyna for her contribution to this work and we hope we will have the pleasure to collaborate with her in the follow-up studies on our MNs fabrication platform., With funding from the Spanish government through the "Severo Ochoa Centre of Excelence" accreditation (CEX2021-001214-S), Peer reviewed
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

A plug, print & play inkjet printing and impedance-based biosensing technology operating through a smartphone for clinical diagnostics

  • Rosati, Giulio|||0000-0002-0227-4561
  • Urban, Massimo|||0000-0001-6083-833X
  • Zhao, Lei|||0000-0003-0291-2655
  • Yang, Qiuyue|||0000-0002-7693-6679
  • De Carvalho Castro Silva, Cecilia|||0000-0003-3933-1838
  • Bonaldo, Stefano|||0000-0003-0712-5036
  • Parolo, Claudio|||0000-0001-9481-4408
  • Nguyen, Emily P.|||0000-0003-4299-2055
  • Ortega, Gabriel
  • Fornasiero, Paolo|||0000-0003-1082-9157
  • Paccagnella, Alessandro|||0000-0002-6850-4286
  • Merkoçi, Arben|||0000-0003-2486-8085
Simplicity is one of the key feature for the spread of any successful technological product. Here, a method for rapid and low-cost fabrication of electrochemical biosensors is presented. This "plug, print & play" method involves inkjet-printing even in an office-like environment, without the need of highly specialized expertise or equipment, guaranteeing an ultra-fast idea to (scaled) prototype production time. The printed biosensors can be connected to a smartphone through its audio input for their impedance readout, demonstrating the validity of the system for point-of-care biosensing. Proper electrodes layout guarantees high sensitivity and is validated by finite element simulations. The introduction of a passivation method (wax printing) allowed to complete the devices fabrication process, increasing their sensitivity. Indeed, the wax allowed reducing the interference related to the parasitic currents flowing through the permeable coating of the employed substrates, which was used for the chemical sintering, thus avoiding the common thermal treatment after printing. As a case study, we used the devices to develop an electrochemical aptamer-based sensor for the rapid detection of neutrophil gelatinase-associated lipocalin (NGAL) in urine - a clinically important marker of acute kidney injury. The aptasensor platform is capable of detecting clinically relevant concentrations of NGAL with a simple and rapid smartphone readout. The developed technology may be extended in the future to continuous monitoring, taking advantage of its flexibility to integrate it in tubes, or to other diagnostic applications where cost/efficiency and rapidity of the research, development and implementation of point of care devices is a must.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Nanostructure Tuning of Gold Nanoparticles Films via Click Sintering

  • Urban, Massimo|||0000-0001-6083-833X
  • Rosati, Giulio|||0000-0002-0227-4561
  • Maroli, Gabriel|||0000-0001-8921-4205
  • Della Pelle, Flavio|||0000-0002-8877-7580
  • Bonini, A.|||0000-0001-9511-0699
  • Sajti, Laszlo
  • Fedel, Mariangela
  • Merkoçi, Arben|||0000-0003-2486-8085
Colloidal metal nanoparticles dispersions are commonly used to create functional printed electronic devices and they typically require time-, energy- and equipment-consuming post-treatments to improve their electrical and mechanical properties. Traditional methods, e.g. thermal, UV/IR, and microwave treatments, limit the substrate options and may require expensive equipment, not available in all the laboratories. Moreover, these processes also cause the collapse of the film (nano)pores and interstices, limiting or impeding its nanostructuration. Finding a simple approach to obtain complex nanostructured materials with minimal post-treatments remains a challenge. In this study, a new sintering method for gold nanoparticle inks that called as "click sintering" has been reported. The method uses a catalytic reaction to enhance and tune the nanostructuration of the film while sintering the metallic nanoparticles, without requiring any cumbersome post-treatment. This results in a conductive and electroactive nanoporous thin film, whose properties can be tuned by the conditions of the reaction, i.e., concentration of the reagent and time. Therefore, this study presents a novel and innovative one-step approach to simultaneously sinter gold nanoparticles films and create functional nanostructures, directly and easily, introducing a new concept of real-time treatment with possible applications in the fields of flexible electronics, biosensing, energy, and catalysis.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Low-cost inkjet-printed nanostructured biosensor based on CRISPR/Cas12a system for pathogen detection

  • Carota, Angela Gilda
  • Bonini, A|||0000-0001-9511-0699
  • Urban, Massimo|||0000-0001-6083-833X
  • Poma, Noemi
  • Vivaldi, Federico Maria
  • Tavanti, Arianna
  • Rossetti, Marianna|||0000-0001-5711-1287
  • Rosati, Giulio|||0000-0002-0227-4561
  • Merkoçi, Arben|||0000-0003-2486-8085
  • Di Francesco, Fabio|||0000-0002-9285-1595
The escalating global incidence of infectious diseases caused by pathogenic bacteria, especially in developing countries, emphasises the urgent need for rapid and portable pathogen detection devices. This study introduces a sensitive and specific electrochemical biosensing platform utilising cost-effective electrodes fabricated by inkjet-printing gold and silver nanoparticles on a plastic substrate. The biosensor exploits the CRISPR/Cas12a system for detecting a specific DNA sequence selected from the genome of the target pathogen. Upon detection, the trans-activity of Cas12a/gRNA is triggered, leading to the cleavage of rationally designed single-strand DNA reporters (linear and hairpin) labelled with methylene blue (ssDNA-MB) and bound to the electrode surface. In principle, this sensing mechanism can be adapted to any bacterium by choosing a proper guide RNA to target a specific sequence of its DNA. The biosensor's performance was assessed for two representative pathogens (a Gram-negative, Escherichia coli, and a Gram-positive, Staphylococcus aureus), and results obtained with inkjet-printed gold electrodes were compared with those obtained by commercial screen-printed gold electrodes. Our results show that the use of inkjet-printed nanostructured gold electrodes, which provide a large surface area, in combination with the use of hairpin reporters containing a poly-T loop can increase the sensitivity of the assay corresponding to a signal variation of 86%. DNA targets amplified from various clinically isolated bacteria, have been tested and demonstrate the potential of the proposed platform for point-of-need applications.
Dipòsit Digital de Documents de la UAB
Publicación Artículo de revisión (ReviewArticle)

Direct writing of graphene electrodes for point-of-care electrochemical sensing applications

  • Zhao, Lei|||0000-0003-0291-2655
  • Piper, Andrew|||0000-0002-1208-8009
  • Rosati, Giulio|||0000-0002-0227-4561
  • Merkoçi, Arben|||0000-0003-2486-8085
Electrochemical sensors are increasingly garnering attention as valuable tools for point-of-care (POC) testing due to their low costs, high sensitivities, and ease of miniaturization. Graphene-based materials, renowned for their tunable electrical conductivity, high specific surface areas, versatile functionality, and biocompatibility; are highly suited for the fabrication of electrochemical sensors with heightened sensitivities. Non-contact, maskless, direct writing methods allow the rapid, large-scale production of graphene electrodes with high design flexibility. Researchers globally are advancing graphene electrode production, aiming for smaller, faster, and more efficient sensors. This review provides a comprehensive overview of recent advances on the direct writing of graphene electrodes for electrochemical sensing applications. It covers the basics of direct writing techniques, the advancements in graphene ink/precursor preparation, structural design, and device integration, with a focus on POC platforms.