Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 4
Encontrada(s) 1 página(s)

Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Using InSAR and GPR techniques to detect subsidence: application to the coastal area of “A Xunqueira” (NW Spain)

  • Alonso Díaz, Alex
  • Casado Rabasco, Josué
  • Solla Carracelas, Maria Mercedes
  • Lagüela, Susana
Climate change represents an important cause of subsidence, especially in coastal cities affected by changes in surface water level and water table. This paper presents a complementary study of Interferometric Synthetic Aperture Radar (InSAR) and Ground Penetrating Radar (GPR) for the early detection of subsidence and sinkhole phenomena. The methodology was applied to a coastal urban area in Galicia, northwest Spain (humid region), showing apparent signs of subsidence and building settlement during the last two years. Two different InSAR methods are compared for the period from June 2021 to March 2022: PSI (Persistent Scatterer Interferometry) and SBAS (Small Baseline Subsets), and the average deformation velocities obtained resulted in −3.0 mm/yr and −4.1 mm/yr, respectively. Additional GPR data were collected in January 2022 to validate the InSAR results, which detected subsidence in agreement with the persistent scatters obtained from the PSI method. This is crucial information to plan preventive maintenance., Xunta de Galicia | Ref. ED431F 2021/08, European Commission | Ref. 101036926, European Commission | Ref. 101021714, Ministerio de Ciencia e Innovación | Ref. RYC2019–026604–I, Ministerio de Universidades | Ref. CAS21/00241, Ministerio de Ciencia e Innovación | Ref. TED2021-130183B-I00
GREDOS. Repositorio Institucional de la Universidad de Salamanca
Publicación Artículo científico (JournalArticle)

Laser Scanning for Terrain Analysis and Route Design for Electrified Public Transport in Urban Areas

  • Sánchez Aparicio, María
  • Martín Jiménez, José Antonio
  • González González, Enrique
  • Lagüela López, Susana
[EN] The orography of the terrain is a key factor for the electrification of vehicles, especially regarding public transport and electric buses. This work deals with the analysis of the use of mobile laser scanning, both terrestrial and aerial, for the evaluation of the orography of urban areas. First, the minimum point density required is evaluated to estimate the slope. The results show that point densities of 1 point/m2, measured with aerial laser scanning, are adequate for the task. Based on this, the design of a route for public transport is presented including the requirements concerning key transit points, maximum slope, and others. Based on the proposed route design, the transformation to an electrified route is analyzed from an economic and environmental point of view. The results show that the implementation of electric buses vs. diesel buses in cities with steep slopes (up to 7%) reduces greenhouse gas emissions (32.59%) as well as economic costs (18.10%)., IBERDROLA SAU European Union through Fondo Social Europeo European Union’s Horizon 2020 research and innovation programme NextGenerationEU programme
GREDOS. Repositorio Institucional de la Universidad de Salamanca
Publicación Artículo científico (JournalArticle)

Optimizing Bladeless Wind Turbines: Morphological Analysis and Lock-In Range Variations

  • González González, Enrique
  • Yáñez, David J.
  • Pozo Aguilera, Susana del
  • Lagüela López, Susana
[EN] This study presents a comprehensive exploration centred on the morphology and surface structure of bladeless wind turbines (BWTs) aimed at optimizing their wind energy harvesting capability. Unlike conventional wind technology where vortex-induced vibration (VIV) is seen as problematic due to aeroelastic resonance, this effect becomes advantageous in BWT energy harvesters, devoid of frictional contact or gears. The primary objective of this study is to develop an optimal BWT design for maximizing energy output. Specifically, this study delves into optimizing the energy performance of these VIV wind energy harvesters, investigating how the geometry (shape and roughness) influences their operating range, known as Lock-In range. The results demonstrate how variations in geometry (convergent, straight, or divergent) can shift the Lock-In range to different Reynolds numbers (Re), modelled by the equation: Re (max Lock-In) = 0.30 α + 4.06. Furthermore, this study highlights the minimal impact of roughness within the considered test conditions., Vortex Bladeless S.L
GREDOS. Repositorio Institucional de la Universidad de Salamanca
Publicación Artículo científico (JournalArticle)

3D-Printed SMC Core Alternators: Enhancing the Efficiency of Vortex-Induced Vibration (VIV) Bladeless Wind Turbines

  • González González, Enrique
  • Yáñez, David J.
  • Hidalgo, Arturo
  • Pozo Aguilera, Susana del
  • Lagüela López, Susana
[EN] This study investigates the application of soft magnetic composite (SMC) materials in alternator core manufacturing for bladeless wind turbines operating under the principle of vortex-induced vibration (VIV), employing additive manufacturing (AM) technologies. Through a comparative analysis of alternator prototypes featuring air, SMC, and iron cores, the investigation aims to evaluate the performance of SMC materials as an alternative to the most commonly used material (iron) in VIV BWT, by assessing damping, resonance frequency, magnetic hysteresis, and energy generation. Results indicate that while alternators with iron cores exhibit superior energy generation (peaking at 3830 mV and an RMS voltage of 1019 mV), those with SMC cores offer a promising compromise with a peak voltage of 1150 mV and RMS voltage of 316 mV, mitigating eddy current losses attributed to magnetic hysteresis. Notably, SMC cores achieve a damping rate of 60%, compared to 67% for air cores and 59% for iron cores, showcasing their potential to enhance the efficiency and sustainability of bladeless wind turbines (BWTs). Furthermore, the adaptability of AM in optimizing designs and accommodating intricate shapes presents significant advantages for future advancements. This study underscores the pivotal role of innovative materials and manufacturing processes in driving progress towards more efficient and sustainable renewable energy solutions., Vortex Bladeless S.L.