Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Artículo científico (JournalArticle)

InP/Si3N4 Hybrid Integrated Lasers for RF Local Oscillator Signal Generation in Satellite Payloads

  • César Cuello, Jessica
  • Zarzuelo García, Alberto
  • Guzmán Martínez, Robinson Cruzoe
  • Mitsolidou, Charoula
  • Visscher, Ilka
  • Timens, Roelof B.
  • Van Dijk, Paulus W.L.
  • Roeloffzen, Chris
  • González Guerrero, Luis
  • Delgado Mendinueta, José Manuel
  • Carpintero del Barrio, Guillermo
This paper presents an integrated tunable hybrid multi-laser module designed to simultaneously generate multiple radiofrequency (RF) local oscillator (LO) signals through optical heterodyning. The device consists of five hybrid InP/Si3N4 integrated lasers, each incorporating an intracavity wavelength-selective optical filter formed by two micro-ring resonators. Through beating the wavelengths generated from three of these lasers, we demonstrate the simultaneous generation of two LO signals within bands crucial for satellite communications (SatCom): one in the Ka-band and the other in the V-band. The device provides an extensive wavelength tuning range across the entire C-band and exhibits exceptionally narrow optical linewidths, below 40 kHz in free-running mode. This results in ultra-wideband tunable RF signals with narrow electrical linewidths below 100 kHz. The system is compact and highly scalable, with the potential to generate up to 10 simultaneous LO signals, being a promising solution for advanced RF signal generation in high throughput satellite payloads., This work has been supported by the European Space Agency through the TRP program “Tuneable Photonic RF Demultiplexer for Broadband Satellites—THORMUX” (GA 870421), by the European Union through the projects TERA6G (GA 101096949), SPRINTER (GA 101070581), and POLYNICES (G.A. 101070549), and by a Spanish national project, “6G-Xtreme” (Ref. TSI-063000-2021-136).
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Otros (Other)

3D-Printed Multimode-Interference-Based Bessel Beamformer for Terahertz Dielectric Waveguides

  • Kumar, Ashish
  • Ayyagarii, Surya Revanth
  • Ali, Muhsin
  • Kasalynas, Irmantas
  • Headland, Daniel
  • Carpintero del Barrio, Guillermo
We demonstrate a Bessel beamformer based on multimode interference (MMI) for the terahertz (THz) wave range. Unlike traditional Bessel beam generation methods, which often rely on bulky free-space optical setups, our approach leverages a 3D-printed cyclic-olefin-copolymer (COC) MMI structure fed from a dielectric waveguide (DW) with a λ/4 slot-waveguide termination (SWT) that provides an index-matched interface for low reflection. Based on this interface and the low losses of the constituent materials, the beamformer achieves a measured transmission efficiency of 93.9% at 275 GHz, with a propagating distance of 20 mm ( ∼ 20 λ ). Even at an extended distance of 35 mm ( ∼ 35 λ ), the beam maintains a 50% efficiency. This approach addresses key limitations of existing free-space methods, offering a workable guided-wave approach to launch a THz Bessel beam., This work was supported in part by the Terahertz Photonics for Communications, Space, Security, Radio-Astronomy, and Material Science (TERAOPTICS) Project under Grant 956857; in part by the Services Joint Undertaking through the European Union’s (EU) Horizon Europe Research and Innovation Program TERA6G and the Horizon Europe Framework Program Project POLYN-ICES under Agreement 101096949 and Agreement 101070549; in part by the National Grant MiBiLab through MICIU/AEI/10.13039/501100011033 and European Regional Development Fund (ERDF)/European Union (EU) under Grant PID2023-149035OB-I00; and in part by the Ministerio de Asuntos Económicos y Transformación Digital and European Union-NextGenerationEU through the project “TERAcom-6G” within ´UNICO I+D 5G-6G 2023 Program for Research Infrastructure and Scientific Equipment under Grant TSI-064100-2023-39. The work of Daniel Headland was supported in part by Australian Research Council’s Discover Early Career Researcher Award through Australian Government under Project DE240100625 and in part by the Article Processing Charge (APC): Universidad Carlos III de Madrid under Agreement CRUE-Madroño 2025.