Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 5
Encontrada(s) 1 página(s)

e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Artículo científico (JournalArticle)

Life cycle assessment studies of concentrated solar power technology: A literature review

  • Palmero González, María Asunción
  • Batuecas Fernández, Esperanza
  • Marugán Cruz, Carolina
  • Santana Santana, Domingo José
The current study offers a literature review of Life Cycle Assessment (LCA) in the context of Concentrated Solar Power (CSP) technology. The methodology involved a bibliometric search and an in-depth critical literature review. The existing reviews indicated opportunities to enhance clarity in the methodology used for selecting literature. Subsequently, the reviewed literature was presented in tabular format, categorized according to CSP plant configuration, subsystem, and technology purpose. The findings indicate lack of available data to perform accurate inventories, and a lack of harmonization of the Life Cycle Impact Assessment methodologies. The results revealed that the most analyzed impact category was climate change, with values averaging 50 g CO2, eq/kWh. There is a need for more LCA investigations about dish-Stirling and Linear Fresnel plants, as well as investigations analyzing other impact categories. Many studies in the CSP LCA domain are directing their attention towards thermal storage, however, the environmental impact of the decommissioning of plants has not yet been thoroughly analyzed. It has been observed that SimaPro is the preferred LCA software by the authors, together with Ecoinvent as database. The literature review revealed a gap in knowledge in LCA studies addressing operational challenges such as corrosion or fatigue, emerging solutions, and updated inventory data, presenting an opportunity for researchers to enhance the market viability of CSP technologies by addressing these deficiencies. Finally, a simplified case study comparing Central Receiver and Parabolic Trough Collector (PTC) systems found that PTC had higher environmental impacts due to the contribution of the Heat Transfer Fluid (HTF)., The authors would like to thank the EU-funded HORIZON MSCA “TOPCSP: Towards competitive, Reliable, Safe and Sustainable Concentrated Solar Power (CSP) Plants” Doctoral Network Project: [grant number 101072537].
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Artículo científico (JournalArticle)

Environmental comparison of dry and hybrid condensing systems in concentrating solar power tower plants

  • Palmero González, María Asunción
  • Batuecas Fernández, Esperanza
  • Fernández Torrijos, María
  • Marugán Cruz, Carolina
This study presents a comprehensive environmental assessment of hybrid and dry condensing systems in central tower Concentrated Solar Power (CSP) plants. Using Life Cycle Assessment (LCA) methodology, the research analyses two optimized configurations based on the recently constructed Redstone CSP plant in South Africa. The study evaluates their environmental impacts, focusing on climate change and water use categories, while also optimizing operational parameters. The LCA results indicate that the dry system configuration significantly reduces water consumption, with 5.1 l/kWh compared to 49 l/kWh for the hybrid system. Although the hybrid configuration generates slightly more energy (582 GWh/year) than the dry configuration (574 GWh/year), the dry system performs better in terms of climate change impact, emitting 6.22 g CO2/kWh compared to 7.96 g CO2/kWh for the hybrid system. These findings suggest that the dry condensing system is a more environmentally sustainable option, particularly in water-scarce regions, despite a marginal reduction in energy output. The study underscores the importance of optimizing CSP plant configurations to achieve a balance between energy production and environmental sustainability., The authors would like to thank the EU-funded HORIZON MSCA “TOPCSP: Towards competitive, Reliable, Safe and Sustainable Concentrated Solar Power (CSP) Plants” Doctoral Network Project: [grant number 101072537], and National Research Project PID2021-122895OB-I00. The authors would also like to acknowledge the financial support received in the Grant PID2021-122278OB-I00 funded by MCIN/AEI/ 10.13039/501100011033 and by “ERDF A way of making Europe“
e-Archivo. Repositorio Institucional de la Universidad Carlos III de Madrid
Publicación Artículo científico (JournalArticle)

Heat flux estimation in CSP receiver tubes using inverse heat transfer analysis

  • Safari, Vahid
  • Fernández Torrijos, María
  • Acosta Iborra, Antonio
  • Sobrino Fernández, Celia
Solar power tower (SPT) receivers operate under extreme thermal conditions, with absorbed heat fluxes on the order of 1 MW/m2 and strongly non-uniform circumferential distributions, making direct flux measurement highly challenging. This study presents, for the first time, an inverse heat-transfer methodology to reconstruct the absorbed heat flux on concentrated solar power (CSP) receiver tubes under realistic operating conditions. A three-dimensional CFD model of a molten-salt receiver tube was validated against induction-heating experiments over a range of Reynolds numbers. Among the turbulence models evaluated, the SST k–ω model showed the best agreement with the experimental data, yielding a surface-temperature RMSE of 17.69 °C. The validated CFD framework was then employed to simulate a representative Gemasolar power-tower configuration using a realistic non-uniform absorbed heat-flux profile. Surface-temperature data extracted at the mid-height of the receiver tube were used as inputs to an inverse heat-conduction model. Accurate heat-flux reconstruction was achieved using a single optimally placed temperature measurement, with no additional benefit from multiple inputs. The minimum deviation of −6.82 % occurred at a circumferential measurement angle of 70°. The inverse method demonstrated strong robustness to synthetic noise, with a minimum average heat-flux RMSE of 0.21 % of the peak flux for white noise and a maximum error of 37.7 % for drift noise. Under well-conditioned conditions, heat-flux deviations remained below 2 %, confirming the suitability of the approach for real-time thermal monitoring of CSP receiver tubes., The authors gratefully acknowledge the financial support provided by the European Union (HORIZON MSCA Doctoral Network, Project number 101072537) and by the grant PID2021-122895OB-I00 funded by MICIU/AEI/10.13039/501100011033 and by “ERDF A way of making Europe.
Repositori Obert UdL
Publicación Contribución de congreso (ConferenceOutput)

Electric Heating Design for Decarbonized Industrial Steam: A Metallic Phase Change Material Power-to-Heat System

  • Cuenca-Romero, Ana
  • Barnetche, Magdalena
  • Prieto, Cristina
  • Al-Saaidi,, Hussein
  • Reinholz, Jonas
  • Melka, Bartlomiej
This study analyzes ways to electrify a thermal energy storage tank with direct steam generation in terms of implementation, power and temperature requirements and performance. The analyzed storage tank unit contains a metallic phase change material as thermal storage medium, with a maximum operation temperature of 430 °C, a charging power of 135 kW and delivers steam at 165 ºC and 6.5 barg. The heating methods analyzed were immersion heaters, heat tracing and heat bands. CFD simulations of a simplified tank geometry were carried out to analyze the different heating methods and the results show that all are applicable in terms of heating up and melting the phase change material. Heat bands deliver higher power per surface area, meeting the desired charging time, but limited contact surface and natural convection lead to significant temperature gradients., This work was partially funded by European Union's HORIZON MSCA Doctoral Network program under grant agreement 101072537 TOPCSP. This research was funded by CETP, the Clean Energy Transition Partnership under the 2022 CETP joint call for research proposals, co-funded by the European Commission (GA N°101069750) and with the funding organizations detailed on https://cetpartnership.eu/fundingagencies-and-call-modules. The project code SERA-20231002 has received funding from the Centro para el Desarrollo Tecnológico y la Innovación (CDTI).
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

Electric Heating Design for Decarbonized Industrial Steam: A Metallic Phase Change Material Power-to-Heat System

  • Cuenca-Romero, Ana
  • Barnetche, Magdalena
  • Prieto, Cristina
  • Al-Saaidi,, Hussein
  • Reinholz, Jonas
  • Melka, Bartlomiej
This study analyzes ways to electrify a thermal energy storage tank with direct steam generation in terms of implementation, power and temperature requirements and performance. The analyzed storage tank unit contains a metallic phase change material as thermal storage medium, with a maximum operation temperature of 430 °C, a charging power of 135 kW and delivers steam at 165 ºC and 6.5 barg. The heating methods analyzed were immersion heaters, heat tracing and heat bands. CFD simulations of a simplified tank geometry were carried out to analyze the different heating methods and the results show that all are applicable in terms of heating up and melting the phase change material. Heat bands deliver higher power per surface area, meeting the desired charging time, but limited contact surface and natural convection lead to significant temperature gradients., This work was partially funded by European Union's HORIZON MSCA Doctoral Network program under grant agreement 101072537 TOPCSP. This research was funded by CETP, the Clean Energy Transition Partnership under the 2022 CETP joint call for research proposals, co-funded by the European Commission (GA N°101069750) and with the funding organizations detailed on https://cetpartnership.eu/fundingagencies-and-call-modules. The project code SERA-20231002 has received funding from the Centro para el Desarrollo Tecnológico y la Innovación (CDTI).