Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 7
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Bricks-on-pedestals silicon optomechanical cavity: a mass sensor for nanoparticles detection

  • Grau-Martínez, Alberto|||0000-0002-2411-1317
  • Mercadé, Laura|||0000-0002-4994-7727
  • Ortiz-Fernández, Raúl|||0000-0002-4998-0201
  • Martínez, Alejandro|||0000-0001-5448-0140
[EN] Optomechanical cavities can be used as highly sensitive mass sensors actuated by an optical field. In this work, we introduce and numerically demonstrate a new design for an optomechanical cavity consisting of a series of asymmetrically distributed rectangular silicon nanobricks, with each brick acting as an independent mechanical resonator but all coupled to the same optical field. Each silicon brick is placed on top of a thin silica pillar that ensures mechanical support whilst providing enough acoustic isolation between the individual mechanical resonances - at GHz frequencies - of each brick. The mass sensing capabilities of this cavity are studied through numerical simulations, proving that a point mass approximation can be used for silica nanoparticles with a radius smaller than 100 nm and that different nanoparticles can be measured independently but simultaneously and in real-time., HORIZON EUROPE Framework Programme (101091968 (MAGNIFIC)); Generalitat Valenciana (CIGE/ 2023/126); Universitat Politècnica de València (PAID-06-22); Agencia Estatal de Investigación (PID2021-124618NB-C21 (ALLEGRO)).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Scattering-matrix approach for a quantitative evaluation of the topological protection in valley photonic crystals

  • Leveque, Gaëtan
  • Pennec, Yan
  • Szriftgiser, Pascal
  • Amo, Alberto
  • Martínez, Alejandro|||0000-0001-5448-0140
[EN] The realization of photonic crystal waveguides with high topological protection enables robust light propagation against defect-induced scattering. It should allow the design of very compact devices by exploiting guiding through sharp bends with low losses and backreflection. In this work we use valley topological triangular resonators coupled to an input waveguide to evaluate the conversion between helical topological edge modes with opposite helicity at sharp bends or routing elements like splitters. To that purpose, we first analyze via numerical simulations the existence of backward scattering at cavity corners or transmission with helicity conversion at the splitter between the input waveguide and the cavity. We show evidence that such processes take place, in particular at sharp corners, which results in transmission minima and split resonances, otherwise nonexistent. In order to evaluate the small coupling coefficients associated with this effect, a phenomenological model based on an exact parametrization of scattering matrices at splitters and corners of the resonators is then introduced. By comparison with the numerical simulations, we are able to quantify the helicity conversion at sharp bends and splitters. Finally, we use the obtained set of phenomenological parameters to compare the predictions of the model with full numerical simulations for fractal-inspired cavities based on the Sierpin ' ski triangle construction. We show that the agreement is overall good but shows more differences for the cavity composed of the smallest triangles. Our results suggest that even in a system exempt from geometrical and structural defects, helicity conversion is not negligible at corners, sharp bends, and splitters. However, simpler but predictive calculations can be realized with a phenomenological approach, allowing simulations of very large devices beyond the reach of standard numerical methods, which is crucial to the design of photonic devices which gather compactness and low losses through topological conduction of electromagnetic waves., G.L. and Y.P. are grateful for the Horizon-RIA action project Magnific (Project No. 101091968) . A.A. is grateful to the European Research Council for support via the grant EmergenTopo (Grant No. 865151, the Labex CEMPI (Grant No. ANR-11-LABX-0007), and Region Hauts-de-France through the CPER Wavetech.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Experimental Evaluation of All-Optical Up- and Down-Conversion of 3GPP 5G NR Signals Using an Optomechanical Crystal Cavity Frequency Comb

  • Fito-Estevan, Vicente
  • Ortiz-Fernández, Raúl|||0000-0002-4998-0201
  • Maria Morant|||0000-0001-5565-7788
  • Mercadé, Laura|||0000-0002-4994-7727
  • Roberto Llorente|||0000-0003-4799-2564
  • Martínez, Alejandro|||0000-0001-5448-0140
[EN] Optomechanical crystal cavities (OMCCs) allow the interaction between localized optical and mechanical modes through the radiation-pressure force. Driving such cavities with blue-detuned lasers relative to the optical resonance can induce a phonon lasing regime where the OMCC supports self-sustained mechanical oscillations. This dynamic state results in a narrow and stable microwave tone that modulates the laser at integer multiples of the mechanical resonance frequency, creating an optomechanical (OM) frequency comb suitable for microwave photonics applications. OMCCs enable compact, low-cost power-efficient all-photonic processing of multiple microwave signals, crucial for current and future beyond-5G systems, whilst being compatible with silicon integrated photonic circuits. This work reports the demonstration of all-optical up- and down-conversion of 3GPP 5G new-radio (NR) signals from the low- to mid- and extended-mid bands using the first and second harmonics of the frequency comb generated in a silicon OMCC. The OM comb generates up to 6 harmonics in the K-band, which is suitable for microwave photonic applications. The experimental demonstration also evaluates the impact of the phase-noise and the signal-to-noise ratio (SNR) in the frequency-converted 5G NR signals when the first and second OMCC harmonics are employed for frequency conversion., The work of Vicente Fito and Raul Ortiz were supported under Grant PAID-01-20 UPV and Grant GVACIACIF/2021/006. This work was supported in part by Generalitat Valenciana CIAICO/2021/201 TERAFLEX Project under Grant IDIFEDER/2021/061, in part by Spanish Ministry of Science and Innovation ALLEGRO under Grant PID2021-124618NB-C21, in part by SLOMO under Grant PDC2022-133267-C21, in part by MUSICIAN (CHISTERA IV Cofund 2021), and in part by the European Commission through MAGNIFIC under Grant HORIZON-CL4-2022-RESILIENCE-01-10 101091968.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Single nanoparticle deposition and detection on a photonic crystal nanobeam cavity

  • Grau-Martínez, Alberto|||0000-0002-2411-1317
  • Mercadé, Laura|||0000-0002-4994-7727
  • Gómez-Herreros, Estefania|||0009-0002-9474-6171
  • Gómez-Gómez, María Isabel|||0000-0001-7548-209X
  • Pinilla-Cienfuegos, Elena|||0000-0002-3734-0821
  • Martínez, Alejandro|||0000-0001-5448-0140
  • Nuño Ruano, Paula
  • Alonso Ramos, Carlos
[EN] Optical cavities are highly interesting elements for detecting nanoparticles, since their optical response is strongly affected - and therefore the response is easily measured - by the presence of a nanoparticle in their vicinity. Ideally, the nanoparticle should be placed in the region with maximum field confinement to maximize light-matter interaction and provide a highly sensitive response. However, in real applications, we usually do not have control over where the nanoparticle is actually placed. In this work, we consider the case of detection of non-resonant gold nanospheres using a silicon photonic crystal nanobeam cavity for the case in which the nanoparticle is not placed in the region of maximum field confinement at resonance (weak coupling). In our experiments, we use APTES (3-aminopropyltriethoxysilane) to functionalize the cavity so that gold nanoparticles can bond to it. Then we use a nanoprinter to deposit gold nanoparticles on predefined positions that, for the cavity under experimental study, turn out to be on a sidewall of the cavity. Optical characterization of the device before and after the nanoparticle deposition shows a large variation in the optical response, which we attribute to the perturbation of the optical resonance by the presence of the nanoparticle. Numerical simulations support our experimental findings, which confirm that optical cavities can perform nanoparticle detection even in cases where they are not placed in regions with maximum electric field., Agencia Estatal de Investigación (PID2021-124618NB-C21, CNS2024-154922); European Commission (101091968).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Dual-mode phonon dynamics and lasing in optomechanical cavities

  • Ortiz-Fernández, Raúl|||0000-0002-4998-0201
  • Martínez, Alejandro|||0000-0001-5448-0140
  • Mas-Arabi, Carlos|||0000-0001-5564-5365
  • Milián Enrique, Carles|||0000-0001-8492-366X
[EN] We use the full nonlinear bifurcation theory as a powerful methodology to thoroughly classify and predict the phonon lasing dynamics in optomechanical cavities. We exemplify its scope in the very relevant and so far vaguely explored dynamics of dual-mode phonon lasing when two independent mechanical modes are directly coupled to one optical field. We uncover a plethora of different lasing regimes in a fixed and realistic cavity geometry, including single- and dual-mode lasing, and an example of chaos. All dynamical regimes are unambiguously associated with bifurcations of different natures, which may exhibit both super- and subcritical natures characterizing the often hysteretic behavior of the systems when they are externally driven by a time-varying laser source. Our results, generalizable to any other optomechanical system, open unprecedented pathways to understand and control the formation and dynamics of optomechanical frequency combs., The authors acknowledge funding from Generalitat Valenciana (GVA, CIACIF/2021/006), HORIZON EUROPE Framework Programme (MAGNIFIC 101091968), Generalitat Valenciana (CIGE/2023/126), and Agencia Estatal de Investigación (ALLEGRO PID2021-124618NB-C21 and MUSICIAN PCI2022-135003-2, CHISTERA IV Cofund 2021). C.M.A. acknowledges funding from the Ministerio de Universidades through the Beatriz Galindo program (BG22/00025).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Phase-noise and stability comparison of fiber-loop and integrated-waveguide coupling in optomechanical crystal oscillators

  • Ortiz-Fernández, Raúl|||0000-0002-4998-0201
  • Martínez, Alejandro|||0000-0001-5448-0140
  • Mercadé, Laura|||0000-0002-4994-7727
  • Yang, Xinyan
[EN] Optomechanical crystal cavities (OMCCs) display appealing features to function as on-chip photonic microwave oscillators (PMOs) when operated in the phonon lasing regime. Silicon OMCCs have so far demonstrated the best performance in terms of phase noise in a free-running configuration. Some preliminary experiments have also demonstrated that the generated microwave tone can be used for mixing wireless signals compliant with 5G standards. Still, more research is needed to identify the primary noise sources and determine the path towards improvement. Here, we report experiments on the realization of optomechanical PMOs operating at 4 GHz under two different driving conditions of the cavity: light coupling via a tapered fiber loop versus using an adjacent integrated waveguide illuminated by a lensed fiber. We performed measurements of the phase noise and the frequency stability in time of the detected tone for both cases and observed an improvement when the light is coupled by an adjacent integrated waveguide. This can be explained by the fact that the ambientinduced motion and changes due to perturbations in the refractive index of the medium surrounding the fiber loop result in variations of the coupling, which in turn affect the stability of the PMO. These results emphasize the relevance of a mechanically stable coupling technique when using such optomechanical devices in real applications, which can be of particular importance in environments where large vibrations are expected., The authors acknowledge funding from the Spanish State Research Agency under projects ALLEGRO, MUSICIAN, and SLOMO (Grants No. PID2021-124618NB-C21, PCI2022-135003-2, and No. PDC2022-133267-C21). We also acknowledge support from the European Commission under the project MAGNIFIC (Grant 101091968).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Performance Evaluation of Dual-Drive Mach-Zehnder Modulator and Optomechanical Crystal Cavity Comb Generation for All-Optical Band Conversion in 5G-Advanced Cellular Systems

  • Fito-Estevan, Vicente
  • Ortiz-Fernández, Raúl|||0000-0002-4998-0201
  • Maria Morant|||0000-0001-5565-7788
  • Mercadé, Laura|||0000-0002-4994-7727
  • Martínez, Alejandro|||0000-0001-5448-0140
  • Roberto Llorente|||0000-0003-4799-2564
[EN] Multiband operation is a key aspect of emerging 5GAdvanced cellular systems, also named 5.5G, which target seamless provision of multi-gigabit per second connectivity employing sub-6 GHz and mm-wave overlapping coverage. All-optical frequency conversion gives flexibility due to the feasible high-speed reconfiguration in broad bands and large radio signal bandwidth. Optical frequency combs, featuring a spectrum of discrete, equally spaced coherent frequency lines, are crucial for high-precision metrology, spectroscopy, and telecommunications. Their effectiveness in all-optical frequency conversion depends on their stability in terms of frequency drift, phase noise, and power distribution across the comb lines. This paper evaluates experimentally the generation of optical frequency combs employing two distinct technologies: a dual-driven Mach-Zehnder modulator (DD-MZM) and an optomechanical crystal cavity (OMCC), and experimentally compares their performance for all-optical frequency conversion of 5G data streams. The DD-MZM implementation generates a comb with flexible line spacing and comprising several spectrum-flat lines with low phase noise (¿88.5 dBc/Hz at 1 kHz offset and ¿108.3 dBc/Hz at 100 kHz offset). The OMCC implementation provides a reduced footprint (182 µm2) since it is implemented on a silicon chip and has the extra advantage of generating an optical comb without an external local oscillator, which reduces its power requirements (under 1 mW) while providing a phase noise of ¿38.3 dBc/Hz at 1 kHz offset and ¿97.1 dBc/Hz at 100 kHz offset. The polarization stability and jitter of both implementations are also evaluated. The experimental demonstration evaluates the error vector magnitude (EVM) of frequency-converted 3GPP 5G NR signals using both implementations, confirming the successful transmission with EVM smaller than 12.01% for DD-MZM up to, The work of Vicente Fito was supported by UPV under Grant PAID-01-20. The work of Raúl Ortiz was supported by GVA under Grant CIACIF/2021/006. The work of Laura Mercadé was supported in part by Generalitat Valenciana under Grant CIGE/2023/126 and in part by UPV under Grant PAID-06-22. This work was supported in part by Generalitat Valenciana under Grant CIAICO/2021/201 TERAFLEX project and Grant IDIFEDER/2021/061, in part by the Spanish Ministry of Science and Innovation under Grant iPHOEBE PID2023-152410OB-I00, Grant ALLEGRO PID2021-124618NB-C21, and Grant MUSICIAN CHISTERA IV Cofund 2021, and in part by the European Commission under Grant MAGNIFIC HORIZON-CL4-2022-RESILIENCE-01-10101091968. Funding for open access charge provided by Universitat Politècnica de València.